Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polyolefin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Thermodynamically leveraged solventless aerobic deconstruction of polyethylene-terephthalate plastics over a single-site molybdenum-dioxo catalyst

Here, we describe the solventless catalytic deconstruction of polyethylene-terephthalate (PET) under an aerobic atmosphere, mediated by an earth-abundant, low-cost activated carbon (AC)-supported single-site molybdenum-dioxo catalyst (AC/MoO 2 ). Catalytic amounts of AC/MoO 2 selectively convert waste PET into its monomer, terephthalic acid (TPA), within 4 h at 265 °C with yields as high as 94% under 1 atm air. Pure crystalline TPA product sublimes from the reaction hot zone, crystallizing on the reactor cold zone, thus avoiding the need for separation and purification steps. This process does not employ any hazardous/toxic reducing agents or solvents, and the catalyst can be recycled multiple times without loss of activity, rendering this process highly atom-efficient. According to computational and experimental mechanistic studies, the AC/MoO 2 catalyst mediates a thermoneutral metal-catalyzed β-scission step, followed by an exothermic step that converts the vinyl benzoate intermediate to TPA and acetaldehyde using trace amounts of moisture in the air. The formation of gaseous acetaldehyde makes the isolation of TPA from the reaction mixture facile and industrially favorable, especially since solvents are unnecessary. The present methodology is also extended to the deconstruction of other frequently used polyester plastics, polybutylene terephthalate (PBT), polyethylene naphthalate (PEN), and polyethylene furanoate (PEF), and operates equally well with post-consumer waste products. Notably, this process is also compatible with plastic mixtures of polyesters with polyolefins, polyamides, and polycarbonates, leading to the selective conversion of each polyester to the corresponding monomer, leaving the residual polymer unchanged and polyester-free.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Techno-economic and life cycle analyses of the synthesis of a platinum–strontium titanate catalyst

The heterogeneous platinum/strontium titanate (Pt/SrTiO 3 or Pt/STO) catalyst has garnered significant attention as a promising candidate for the hydrogenolysis of polyolefins to hydrocarbon oils. This study evaluates the cost and environmental impacts of a newly developed scalable Pt/STO catalyst production, which includes the synthesis of the STO support and the deposition of Pt onto the support. This two-step synthesis plays a significant role in assessing the commercial feasibility of the catalyst, while energy consumption during the process plays an important role in its environmental impacts. The CatCost and the Research and Development Greenhouse Gases, Regulated Emissions, and Energy use in Technologies (R&D GREET) models were used, respectively, to perform techno-economic analysis (TEA) and life cycle analysis (LCA) of the newly developed catalyst. The TEA showed that the raw materials, accounting for approximately 76% of the total operation cost, has a profound effect on the estimated catalyst cost, mainly due to the platinum precursor. The LCA findings indicated that the catalyst production generates greenhouse gas (GHG) emissions of 66 kg CO 2 e per kg, primarily due to the use of solvents and electricity in the process. The sensitivity analysis indicated that the total operating costs (OpEX), platinum precursor cost, and spent catalyst value (SCV) significantly impact the cost of the synthesized catalyst. Additionally, adopting solvent recovery strategies and using renewable electricity can reduce the GHG emissions of catalyst production to 29 kg CO 2 e per kg.

Heterogeneous Platinum/strontium titanate Catalyst↗
DOE OSTI2025

Backbone editing and deconstruction of polyethylene by Beckmann rearrangement and hydrogenolysis

Polyethylene is the most widely produced commodity plastic and is used in many applications, including packaging, insulation, and medical devices. However, the inertness of polyethylene makes chemical recycling inefficient and challenging. We report the conversion of oxidized high-density and low-density polyethylene, formed by direct, catalytic oxidation, to polyamides by Beckmann rearrangement of the corresponding oximes. These polyamides have enhanced surface properties over those of unmodified polyethylene, while maintaining the same, favorable mechanical profiles. The amide sites were reductively cleaved by hydrogenolysis with ruthenium-based catalysts to furnish alcohol- and amine-terminated fragments, which were used for the synthesis of polyurea-urethanes with poly(tetrahydrofuran) and methylene diphenyl diisocyanate. These experiments show how to install cleavable moieties into the backbone of polyethylene to facilitate deconstruction and the generation of new materials to affect greater sustainability in polyolefins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Microstructure of amide-functionalized polyethylenes determined by NMR relaxometry

Amidation of polyethylenes creates a range of amide-containing materials with enhanced properties, but the effect of these functional groups on the microstructure of these new materials is not known. Here we employ solid-state nuclear magnetic resonance (NMR) techniques to analyze the microstructure of amide-modified polyethylenes. While a decrease in crystallinity was observed with increasing amounts of functionalization, we found by measuring the chain mobility of the crystalline, amorphous, and interphasial regions of the polyethylenes with NMR relaxation techniques that the grafted amidyl groups partition into the rigid amorphous fraction (RAF) between the crystalline and amorphous regions. The chemical specificity of these NMR experiments creates precise assessments of the location of functional groups within the materials. Together, these insights into the microstructure and morphology of amide-containing polyethylenes lay a foundation for a deeper understanding of the structure and properties of functional polyolefins.

Haber, Shira [Lawrence Berkeley National Laborator↗
DOE OSTI2026

Recent advances in chemical recycling and upcycling of plastic waste into valuable materials, chemicals, and energy: a comprehensive review

The global plastic waste crisis has increased in severity in recent years: annual plastic production is projected to reach 500 million metric tons by 2025, and plastic waste accumulation is expected to surpass 12 billion metric tons. Despite these growing volumes, only ∼9% of plastic waste is currently recycled; the majority is either landfilled, incinerated, or mismanaged, contributing to escalating greenhouse gas emissions—from 1.7 Gt carbon dioxide equivalent (CO 2 -eq.) in 2015 to an estimated 6.5 Gt CO 2 -eq. by 2050—and physical environmental pollution. This review provides a comprehensive overview of advanced plastic upcycling strategies to address this issue and recover value from diverse plastic waste streams. Recent developments in solvent-based dissolution, chemical depolymerization, and thermochemical conversions are examined for major plastic types, including polyolefins, polycondensation polymers, and PVC. Underlying reaction pathways, catalyst designs, and processing parameters that govern product selectivity, efficiency, and conversion yields are discussed in depth. Emerging techniques such as microwave-assisted depolymerization, tandem catalysis, and co-processing approaches are highlighted for their potential to enhance efficiency under milder conditions. Emphasis is also placed on the production of high-value products such as monomers, naphtha-range hydrocarbons, and syngas, and discussion is provided on catalyst stability, contaminant removal, scalability, life cycle effects on the environment, and technoeconomic viability. Finally, the review outlines future research directions focused on catalyst innovation, integrated process design, supportive policy frameworks, and interdisciplinary collaboration. All recommendations are aimed at accelerating large-scale implementation of plastic upcycling technologies and advancing the global circular plastics economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Application of Cable Condition Monitoring Technologies to Assess Age-Related Degradation of Industrial Cables Installed in Harsh Environments

The aging of electrical cables has been the subject of substantial research and development (R&D) projects performed by national and international laboratories, universities, and private organizations for many years. This R&D was conducted to develop guidance, equipment, and techniques to support aging management of in-service cables in industrial facilities such as nuclear power plants, research reactors, waste facilities, and fuel fabrication plants. Through these research efforts, condition monitoring technologies have been developed that can determine the severity of age-related degradation that occurs in industrial cables and insulation polymers during service. This paper summarizes the results of aging assessments that were performed for cables installed in two U.S. nuclear power plants, one a pressurized water reactor and one a boiling water reactor. These cables had been in service for over 40 years and during plant operation were exposed to harsh environmental conditions including elevated temperatures and radiation. For these assessments, a comprehensive series of measurements was performed to assess the aged condition of the cables. These cables came from different manufacturers, were manufactured in different years, and were constructed with a variety of jacket and insulation polymers including chloro-sulfonated polyethylene (CSPE), cross-linked polyethylene (XLPE)/cross-linked polyolefin (XLPO), neoprene, and ethylene propylene rubber (EPR). The goal of these assessments was to determine the current aged condition of the cable polymers and provide an estimate of how long the cable insulation materials could remain exposed to their in-service environmental conditions before reaching their end-of-life condition. Both nuclear power plants have received license renewals to extend their operation from 40 to 60 years, and the utilities need objective evidence to show that critical components such as cables will be able to function safely and reliably during the extended operating period. Furthermore, the results of these assessments showed that the cables exhibited different aged conditions depending on the type of polymers they were constructed with and the environment they were exposed to during service. Some of the cables and insulation polymers showed signs of significant age-related degradation and were estimated to have approximately 5 years of remaining service life. Other cables exhibited no signs of significant age-related degradation and were estimated to have 50 years or more of remaining service life. Using the results of these cable aging assessments, plant personnel were able to (1) determine the overall aged condition of cables and insulation polymers using objective test results, (2) identify aged or degraded cables before they caused operability issues, and (3) avoid unnecessary and costly replacement of cables that can continue to operate safely and reliably.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Glass/glass photovoltaic module reliability and degradation: a review

Glass/glass (G/G) photovoltaic (PV) module construction is quickly rising in popularity due to increased demand for bifacial PV modules, with additional applications for thin-film and building-integrated PV technologies. G/G modules are expected to withstand harsh environmental conditions and extend the installed module lifespan to greater than 30 years compared to conventional glass/backsheet (G/B) modules. With the rapid growth of G/G deployment, understanding the outdoor performance, degradation, and reliability of this PV module construction becomes highly valuable. In this review, we present the history of G/G modules that have existed in the field for the past 20 years, their subsequent reliability issues under different climates, and methods for accelerated testing and characterization of both cells and packaging materials. We highlight some general trends of G/G modules, such as greater degradation when using poly(ethylene-co-vinyl acetate) (EVA) encapsulants, causing the industry to move toward polyolefin-based encapsulants. Transparent backsheets have also been introduced as an alternative to the rear glass for decreasing the module weight and aiding the effusion of trapped gaseous degradation products in the laminate. New amendments to IEC 61215 standard protocols for G/G bifacial modules have also been proposed so that the rear side power generation and UV exposure will be standardized. We further summarize a suite of destructive and non-destructive characterization techniques, such as current-voltage scans, module electro-optical imaging, adhesion tests, nanoscale structural/chemical investigation, and forensic analysis, to provide deeper insights into the fundamental properties of the module materials degradation and how it can be monitored in the G/G construction. This will set the groundwork for future research and product development.

14 SOLAR ENERGY↗
DOE OSTI2020

Damp Heat Induced Degradation of Silicon Heterojunction Solar Cells With Cu-Plated Contacts

Damp heat exposure is one of the most stringent environments for testing the durability of solar cells in packaged modules. Damp heat stresses and induces a variety of degradation modes in solar cells and modules: for example, moisture-induced corrosion of electrodes and interconnections, deterioration of polymeric materials, and/or thermally activated diffusion processes. To screen for these and other potential degradation modes, we subject one-cell modules containing silicon heterojunction (SHJ) solar cells with Cu-plated contacts to extended damp heat tests at 85 °C/85% relative humidity. SHJ cells were laminated with two common encapsulants: ethylene vinyl acetate (EVA) and polyolefin elastomer (POE), and two constructions: glass-backsheet and glass-glass. We observe degradation in all components of solar cell maximum power (PMP): current, voltage, and fill factor, and find evidence of increased carrier recombination and nonideal diode behavior with increasing stress. For glass-backsheet constructions, EVA samples generally degrade more than POE by a factor of approximately 1.5x PMP, and the different encapsulants produce different degradation patterns. Similar trends are observed in glass-glass modules, but to a lesser degree. In a different experiment, we observe a decrease in effective minority carrier lifetime of nonmetallized SHJ precursors measured after damp heat. This implies that some degradation unrelated to the contacts is to be expected and confirms the observation of increasing recombination.

14 SOLAR ENERGY↗
DOE OSTI2019

Field-Aged Glass/Backsheet and Glass/Glass PV Modules: Encapsulant Degradation Comparison

Ethylene vinyl acetate (EVA) is the predominant encapsulant in crystalline-silicon photovoltaic (PV) modules; however, its degradation is a subject of major concern, which causes significant power loss under field conditions. This article presents a comparison of EVA degradation in field-aged PV modules with glass/backsheet (G/B) and glass/glass (G/G) architectures. Modulelevel characterization included UV fluorescence imaging and I-V measurements. Material analytical techniques, including colorimetry, differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared spectroscopy, and Raman spectroscopy, were performed to correlate the module performance parameters with EVA material properties. An intense EVA discoloration in G/G modules was observed, which was corroborated by higher module Isc and Pmax degradation rates compared with its counterpart G/B modules. Higher power degradation was accompanied by a significant increase in EVA crosslinking, vinyl acetate content, yellowness index, and presence of functional groups containing unsaturated moieties that are linked to degradation products of photothermal reaction, and a higher decrease in the degree of crystallinity. The absence of a polymeric backsheet in hermetically sealed G/G modules, which restricts photobleaching and enhances the entrapment of volatile acetic acid and other degradation by-products, plays a major role in causing higher EVA degradation in G/G modules. This article concludes that EVA might have been a good choice of an encapsulant for the G/B modules over the decades, but it may prove to be an inappropriate choice for the G/G modules because of potential degassing, corrosion, and/or discoloration issues. Ionomers or polyester-based encapsulants like polyolefins could be best suited for G/G modules as it appears to be a current trend in the industry.

14 SOLAR ENERGY↗
DOE OSTI2021

Failure Analysis of a New Polyamide-Based Fluoropolymer-Free Backsheet After Combined-Accelerated Stress Testing

The viability of novel coextruded, fluoropolymer-free backsheets for photovoltaic (PV) modules has been questioned as a result of a large number of early-life backsheet failures in PV installations containing one of the earliest co-extruded polyamide (PA)-based backsheet to reach the market, “AAA.” New PV reliability testing protocols have been recently developed and applied to backsheets to reproduce failures observed in the field and evaluate the durability of novel backsheet materials and designs prior to commercialization. A new co-extruded PA-based backsheet was tested using combined-accelerated stress testing (C-AST) and demonstrated a greater lifetime than AAA, and some other fluoropolymer-based backsheets such as polyvinylidene fluoride. The improved PA-based backsheet also eventually failed by through-thickness cracking. Using surface and bulk material characterization techniques, we performed a comprehensive study of material properties before and after the stress testing. Aging of the backsheet resulted in an increase of surface roughness by erosion of the outer PA layer. However the failure is more likely related to an increase in crystallinity of the polyolefin core layer reducing the backsheet tearing energy. The analysis can ultimately inform on the specific weaknesses of the materials so that the manufacturer can improve the backsheet design to extend its lifetime.

14 SOLAR ENERGY↗
DOE OSTI2024

Investigating the Crosslinking, Degradation, and Adhesion Behavior of Photovoltaic Encapsulants Under Thermal Accelerated Aging

Degradation of photovoltaic (PV) module encapsulant characteristics that lead to mechanical embrittlement and delamination remains a cause of failure in solar installations. A multiscale reliability model connecting the encapsulant mechanical and fracture properties to the degraded molecular structure and interfacial bonding to adjacent solar cell and glass substrates was previously published. The model, developed primarily for poly(ethylene-co-vinyl acetate) acetate (EVA) encapsulants, remains to be experimentally validated. Determining the degradation and crosslinking kinetics of alternative encapsulants, such as polyolefin elastomer (POE) and EVA/POE/EVA composites (EPE), can generalize the model. In this work, we subject fully cured EVA, POE, and EPE encapsulants to accelerated thermal aging to determine how high temperatures impact reaction kinetics. An increase in gel content (crosslinking) and decrease in crystallinity of the encapsulants under hot-aerobic (90 degrees C, 22% RH) and hot-anaerobic (90 degrees C, sealed in N 2 air) aging were observed, even in the absence of UV and crosslinking initiators. Fourier transform infrared spectroscopy (FTIR)-attenuated total reflectance analysis showed insignificant encapsulant degradation, demonstrating the critical role of UV and moisture in accelerating degradation. Adhesion testing performed on coupon-level specimens (cell/encapsulant/glass laminates) showed decreases in adhesion energy, Gc , from 5000 h of hot-dry (90 degrees C, ~1% RH) and hot-humid (90 degrees C, 60% RH) aging. POE coupons demonstrated the best stability, followed by EPE then EVA. For EVA and POE, hot-humid aged coupons experienced a larger decrease in Gc due to enhanced hydrolytic degradation. Hot-dry aging condition demonstrated that thermal degradation of the interface could be significant even if the encapsulant experiences negligible degradation in the absence of UV and elevated humidity.

accelerated aging↗
DOE OSTI2025

Sequential Stress Identifies Processing Defects in Bifacial Photovoltaic Modules That Limit Durability

Here, we use sequential stress to investigate hurdles to bifacial photovoltaic (PV) module durability from lamination defects. We test mini-modules with glass/glass (G/G) and glass/transparent-backsheet (G/TB) constructions using either ethylene vinyl acetate or polyolefin elastomer (POE) based encapsulants under a modified IEC 63209-2 sequential stress. This sequence includes multiple iterations of damp heat (DH200), full spectrum light exposure (A3), thermal cycling (TC50), and humidity/freeze (HF10). We compare indoor stress with outdoor exposure. Results show similar relative trends in degradation after a year outdoors compared to our first stress cycle. Subsequent stress cycles impart more severe damage than outdoor exposure for the short outdoor duration used here. Edge-pinch lamination defects in G/G mini-modules limit durability causing delamination and cell cracks. Conversely, we observe greater degradation in G/TB mini-modules compared to G/G in the later stages of the stress sequence when the backsheets are directly exposed to UV-containing light. Our results highlight: 1) the utility of sequential stress testing to uncover degradation modes in bifacial PV, 2) implications of using mini-modules for testing PV quality, and 3) the importance of lamination defects that must be avoided to ensure durability as the industry adopts G/G or G/TB packaging.

14 SOLAR ENERGY↗
DOE OSTI2020

Stability of Tin-Lead Halide Perovskite Solar Cells

Tin-lead perovskites have low band gaps (1.2 eV - 1.4 eV) that offer complementary absorption spectra to mixed halide perovskites with band gaps in the range of 1.6 eV - 1.85 eV. In combination, tin-lead and mixed halide perovskites can be used to make efficient all-perovskite tandem solar cells. While these can achieve high efficiency, they are hampered by the unproven longterm stability of tin-containing perovskites. We make the first demonstration of tin-lead perovskite solar cells that pass benchmark 1000-hour tests of stability under stressors of heat, light, and atmospheric exposure. We identify that mixed tin-lead perovskites oxidise by a different chemical pathway, one that is much less favourable, than the oxidation pathway followed by pure tin perovskites, making them significantly more stable. Fortuitously, mixed tin-lead perovskites also have band gaps that are close to ideal for the rear cell of an all-perovskite monolithic two-junction tandem. Beyond selecting the composition of the perovskite to be one that has inherently suppressed tendency to oxidise, we also fabricate a novel heterojunction-based architecture that eliminates the commonly used acidic PEDOT:PSS layer, which leads to enhanced stability. By packaging the resulting solar cell in a glass-on-glass package with a pliable low-elastic-modulus polyolefin encapsulant and a butyl rubber edge seal, we also demonstrate that the low band gap perovskite solar cell that passes the IEC damp heat test for thin film solar cells - a milestone that demonstrates the removal of a significant impediment to the commercialization of high efficiency perovskite tandem solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

BACKFLIP: Identification of Materials and Changes Upon Aging of Emerging Fluoropolymer-Free and Industry-Benchmark PV Backsheets

Extending lifetimes of photovoltaic (PV) modules and decreasing manufacturing and decommissioning costs are motivating research of novel PV module backsheet materials. Backsheet integrity is critical to the safety and performance of a PV module, however, the polymeric materials are often vulnerable to environmental degradation. The long-term durability of emerging polyolefin (PO) materials is being examined to inform regarding the possible replacement of laminated backsheets containing polyethylene terephthalate (PET) cores and fluoropolymer protective inner/outer layers. This study compares traditional PET-based backsheets with novel, co-extruded, and recyclable PO-based backsheets after being subjected to hygrometric and UV photolytic accelerated weathering. A large set of characterization methods will compare physical, chemical, structural, mechanical, and insulating properties of these backsheets and the resulting mini-module (MiMo) PV performances. The study of chemical composition, glass- and phase-transition temperatures, degree of crystallinity, and crystalline structure are described here.

mini-module↗
DOE OSTI2021

Mechanistic Insights to Degradation of PERC Minimodules with Differentiated Packaging Materials & Module Architectures

In this paper, we study the degradation behavior of glass-backsheet (GB) and double glass (DG) multicrystalline sil- icon monofacial PERC minimodules, fabricated using polyolefin elastomer (POE) and ethylene vinyl acetate (EVA) encapsulants, undergoing exposures of modified damp-heat (80 °C / 85% RH), with and without full spectrum light. The completed exposure time, at this time, is 1512 hours with each step of 504 hours. Step- wise measurements are conducted throughout exposures including current-voltage (I-V ) curves, Suns-V oc , electroluminescence (EL) images, and four-point proof loading with EL for tracking changes in mechanical properties in encapsulants by cell fracture probability. The results show that GB minimodules of both encapsulants, compared to DG minimodules, experience more changes in features of I-V and Suns-V oc measurements. There is no development of PV cell cracking during proof loading as seen from EL images and the load versus load line displacement plots currently.

14 SOLAR ENERGY↗
DOE OSTI2023

A Comparison of Emerging and Industry Benchmark Photovoltaic Backsheets Between Different Outdoor Locations

Recent interest within the photovoltaic (PV) module industry is largely directed toward enhanced lifetimes in the field, balanced with improved recyclability. Traditionally, fluoropolymer-based backsheets have been used, however, are difficult to recycle. Emerging polyolefin (PO)-based backsheets are more recyclable and can be formulated to be robust. Properties of different fluoropolymer- and non-fluoropolymer-based backsheet coupons and in encapsulated silicon mini modules that have been fielded in Albuquerque, NM and Cocoa, FL are reported here. Seven backsheets were examined: two novel PO's, TPT, APO, PPE, AAA, and KPf. Methods of examination include module electrical performance (I - V flash test), surface morphology (optical microscope and gloss), polymer chemical structure (FTIR), EL imaging, mechanical tensile testing, DC breakdown voltage, DSC (phase transitions), and optical performance (reflectance spectra).

industries↗
DOE OSTI2020

Polyethylene upcycling to long-chain alkylaromatics by tandem hydrogenolysis/aromatization

The current scale of plastics production and the accompanying waste disposal problems represent a largely untapped opportunity for chemical upcycling. Tandem catalytic conversion by platinum supported on γ-alumina converts various polyethylene grades in high yields (up to 80 weight percent) to low-molecular-weight liquid/wax products, in the absence of added solvent or molecular hydrogen, with little production of light gases. The major components are valuable long-chain alkylaromatics and alkylnaphthenes (average ~C 30 , dispersity Ð = 1.1). Coupling exothermic hydrogenolysis with endothermic aromatization renders the overall transformation thermodynamically accessible despite the moderate reaction temperature of 280°C. This approach demonstrates how waste polyolefins can be a viable feedstock for the generation of molecular hydrocarbon products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Chemically recyclable thermoplastics from reversible-deactivation polymerization of cyclic acetals

Identifying plastics capable of chemical recycling to monomer (CRM) is the foremost challenge in creating a sustainable circular plastic economy. Polyacetals are promising candidates for CRM but lack useful tensile strengths owing to the low molecular weights produced using current uncontrolled cationic ring-opening polymerization (CROP) methods. Here, we present reversible-deactivation CROP of cyclic acetals using a commercial halomethyl ether initiator and an indium(III) bromide catalyst. Using this method, we synthesize poly(1,3-dioxolane) (PDXL), which demonstrates tensile strength comparable to some commodity polyolefins. Depolymerization of PDXL using strong acid catalysts returns monomer in near-quantitative yield and even proceeds from a commodity plastic waste mixture. Our efficient polymerization method affords a tough thermoplastic that can undergo selective depolymerization to monomer.

Abel, Brooks A.↗