Search NASA⌕ Search

SEARCH · Search NASA

Results for “Power conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Cascade type-I quantum well diode lasers emitting 960 mW near 3 μm

The cascade pumping scheme reduced the threshold current density of high power type-I quantum well GaSb-based λ ∼ 3 μm diode lasers down to ∼100 A/cm{sup 2} at room temperature. Laser heterostructures had single GaInAsSb quantum well gain stages connected in series by means of GaSb/AlSb/InAs tunnel junctions followed by InAs/AlSb electron injectors. Devices with densely stacked two and three gain stages and 100-μm-wide aperture demonstrated peak power conversion efficiency of 16% and continuous wave output power of 960 mW. Corresponding narrow ridge lasers demonstrated above 100 mW of output power. The experiment showed that the bandwidth of the gain and its rate of increase with current depended strongly on the thickness of AlSb layer separating electron injectors from quantum wells. The possible impact of electron injector interfaces and ionized impurities on the carrier scattering and recombination in the active quantum well is discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Defective TiO 2 with high photoconductive gain for efficient and stable planar heterojunction perovskite solar cells

Formation of planar heterojunction perovskite solar cells exhibiting both high efficiency and stability under continuous operation remains a challenge. Here, we show this can be achieved by using a defective TiO 2 thin film as the electron transport layer. TiO 2 layers with native defects are deposited by electron beam evaporation in an oxygen-deficient environment. Deep-level hole traps are introduced in the TiO 2 layers and contribute to a high photoconductive gain and reduced photocatalytic activity. The high photoconductivity of the TiO 2 electron transport layer leads to improved efficiency for the fabricated planar devices. A maximum power conversion efficiency of 19.0% and an average PCE of 17.5% are achieved. In addition, the reduced photocatalytic activity of the TiO 2 layer leads to enhanced long-Term stability for the planar devices. Under continuous operation near the maximum power point, an efficiency of over 15.4% is demonstrated for 100 h.

14 SOLAR ENERGY↗

Optimizing energy yield of monolithic perovskite/silicon tandem solar cells in real-world Conditions: The impact of luminescent coupling

Efficient light management is key to maximizing power conversion efficiency (PCE) in monolithic perovskite/silicon tandem solar cells. Achieving peak efficiency requires closely matched current generation in all junctions, especially in integrated configurations. However, real-world conditions vary significantly due to factors such as sunlight spectrum, diffuse-to-direct sunlight ratio, angular distribution of light, subcell temperature coefficients, and ground reflection. This study introduces a comprehensive optical and device simulation to optimize perovskite/silicon tandem cells, considering experimental luminescent coupling (LC) efficiency and its dependence on working conditions, alongside variations in radiative recombination, effect of temperature on absorptivity spectra, and cloud cover. Our results show potential energy yield improvements of up to 1.4 % with LC, based on current perovskite radiative recombination records, and up to 4 % with direct bandgap materials. Although radiative recombination's dependence on excitation intensity reduces output power and requires thicker absorbers, LC compensates for these losses. LC also lowers the optimized bandgap for the perovskite top cell from 1.72 eV to 1.64–1.68 eV, or even lower in regions with redshifted irradiance. Additionally, optimization revealed that thinner silicon bottom cells require a higher perovskite top cell bandgap, impacting the balance between fabrication cost and cell stability.

14 SOLAR ENERGY↗

Chalcogen effect on the photovoltaic performance of nonfused-ring small molecular electron acceptors for efficient organic solar cells

Fused-ring electron acceptors (FREAs) are the current working horse for the top performing organic solar cells (OSCs). Nevertheless, these FREAs surfer from high synthetic complexity, production costs and poor scalability, hindering their industrialization. Developing nonfused-ring electron acceptors (NFREAs) is a more feasible alternative solution towards future photovoltaic applications. Here, in this work, a series of NFREAs have been designed and synthesized by introducing chalcogen atoms on the side chains for OSCs. The introduced chalcogen atoms (O, S, and Se) not only modulated the energy levels but also finely tuned the intermolecular interactions. Especially, the formed S···S and Se···Se intermolecular interactions in TTS-4F and TTSe-4F resulted in higher molecular crystallinity than TTO-4F. Unexpectedly, the strong Se···Se interactions also led the aggregation of TTSe-4F and formation of large domains in the PM6:TTSe-4F blend. The moderate S···S interactions in TTS-4F enabled an optimal phase separation with more ideal nano fibrils distributed in the PM6:TTS-4F blend, facilitating the charge separation and transport. As a result, TTS-4F based devices achieved a champion power conversion efficiency (PCE) of 14.74%, higher than the TTO-4F (8.76%) and TTSe-4F (11.56%) based devices.

36 MATERIALS SCIENCE↗

Optimized molecular aggregation via incorporating fluorinated unit in the polymer donor for 17.3% efficiency organic solar cells

Regulating molecular aggregation state via chemical modification of photovoltaic materials to optimize the blend morphology is an effective and challenging strategy to improve the photovoltaic performance of organic solar cells (OSCs). Here, in this work, we demonstrate a random terpolymerization strategy by incorporating 1,3-bis(5-bromo-4-fluorothiophen-2-yl)-5,7-bis(2-ethylhexyl)-4H,8H-benzo[1,2-c:4,5-c']bisthiophene-4,8-dione (BFT, 30 mol%) unit with fluorinated π-bridges into the molecular backbone of PM6 and develop a terpolymer PF1. Benefiting from the strong electronegativity of fluorine atom and noncovalent interaction of F---S, the energy levels, molecular ordering, and aggregation properties of the polymer donors are precisely regulated. Notably, in the active layer film based on PF1: Y6, the π-π stacking distance can reduce to 3.51 Å, which is significantly smaller than that of PM6:Y6 (3.65 Å) and boosts the effective exciton dissociation and charge transport, thereby effectively optimize the photovoltaic properties of the related devices. As a result, the PF1:Y6-based OSCs achieved a power conversion efficiency (PCE) of up to 17.3%, which is much higher than that of the controlled OSCs based on PM6:Y6 (PCE = 16.2%). These results demonstrate high-efficiency OSCs enabled by regulating molecular aggregation via terpolymerization strategy.

14 SOLAR ENERGY↗

Tetrahydrofuran Processable Organic Solar Cells with 19.45% Efficiency Realized by Introducing High Molecular Dipole Unit Into the Terpolymer

Developing organic solar cells (OSCs) processable with halogen‐free, non‐aromatic solvents is crucial for practical applications, yet challenging due to the limited solubility of most photoactive materials. Here, this study introduces high‐performance terpolymers processable in tetrahydrofuran (THF) by incorporating dithienophthalimide (DPI) into the PM6 backbone. DPI extends the absorption band, lowers HOMO levels, and improves THF solubility and film crystallinity through its large dipole moment effect. Optimal PBD‐10:L8‐BO devices processed with THF achieved a competitive power conversion efficiency (PCE) of 18.79%, approaching chloroform‐processed devices (19.04%). By introducing PBTz‐F as a second donor, ternary OSCs reached an impressive 19.45% PCE when processed with THF. This improvement stems from enhanced photon generation, improved morphology, better charge transport, longer exciton lifetimes, efficient charge dissociation and collection, and suppressed recombination. These PCEs of 18.79% and 19.45% for binary and ternary blend OSCs, respectively, represent the highest reported efficiencies for OSCs processed with halogen‐free, non‐aromatic solvents. This work demonstrates significant progress in eco‐friendly OSC fabrication, paving the way for more sustainable and commercially viable organic photovoltaic technologies.

36 MATERIALS SCIENCE↗

Siloxane-functional small molecule acceptor for high-performance organic solar cells with 16.6% efficiency

As one of the simple but most effective molecular design strategies, side-chain engineering has been widely employed to modify the photoelectric properties of active layer materials for boosting the photovoltaic performance of organic solar cells (OSCs). In this work, a functionalized small molecule acceptor (SMA) named BTSi-4F with a bulky siloxane-terminated solubilizing group as side-chains, derived from a classical SMA of Y6, was designed and synthesized. The results demonstrate that the introduction of siloxane-functional terminated groups into SMA not only affects the optical absorption and molecular energy levels, but also regulates the miscibility between the polymer donor and SMA. Compared to the original Y6, BTSi-4F exhibits a better solubility, upshifted lowest unoccupied molecular orbital (LUMO) energy level, more ordered molecular packing, and higher electron-mobility. Matched with a wide bandgap polymer donor PM6, the chlorobenzene-processed OSCs based on PM6:BTSi-4F achieved a superior power conversion efficiency (PCE) of 16.6% with both high open-circuit voltage (V oc ) of 0.90 V and high fill factor (FF) of 0.77, while the devices based on PM6:Y6 obtained a much lower PCE of 13.0% with a V oc of 0.81 V and FF of 0.69 under the same conditions. This work offers a promising molecular design strategy of siloxane-terminated side chain engineering to develop high-performance SMAs for efficient OSCs.

14 SOLAR ENERGY↗

Crown Ether Modulation Enables over 23% Efficient Formamidinium-Based Perovskite Solar Cells

The use of molecular modulators to reduce the defect density at the surface and grain boundaries of perovskite materials has been demonstrated to be an effective approach to enhance the photovoltaic performance and device stability of perovskite solar cells. Herein, we employ crown ethers to modulate perovskite films, affording passivation of undercoordinated surface defects. This interaction has been elucidated by solid-state nuclear magnetic resonance and density functional theory calculations. The crown ether hosts induce the formation of host-guest complexes on the surface of the perovskite films, which reduces the concentration of surface electronic defects and suppresses nonradiative recombination by 40%, while minimizing moisture permeation. As a result, we achieved substantially improved photovoltaic performance with power conversion efficiencies exceeding 23%, accompanied by enhanced stability under ambient and operational conditions. This work opens a new avenue to improve the performance and stability of perovskite-based optoelectronic devices through supramolecular chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Toward Mass-Production of Transition Metal Dichalcogenide Solar Cells: Scalable Growth of Photovoltaic-Grade Multilayer WSe2 by Tungsten Selenization

Semiconducting transition metal dichalcogenides (TMDs) are promising for high-specific-power photovoltaics due to their desirable band gaps, high absorption coefficients, and ideally dangling-bond-free surfaces. Despite their potential, the majority of TMD solar cells to date are fabricated in a nonscalable fashion, with exfoliated materials, due to the lack of high-quality, large-area, multilayer TMDs. Here, we present the scalable, thickness-tunable synthesis of multilayer WSe2 films by selenizing prepatterned tungsten with either solid-source selenium at 900 degrees C or H2Se precursors at 650 degrees C. Both methods yield photovoltaic-grade, wafer-scale WSe2 films with a layered van der Waals structure and superior characteristics, including charge carrier lifetimes up to 144 ns, over 14x higher than those of any other large-area TMD films previously demonstrated. Simulations show that such carrier lifetimes correspond to ~22% power conversion efficiency and ~64 W g-1 specific power in a packaged solar cell, or ~3 W g-1 in a fully packaged solar module. The results of this study could facilitate the mass production of high-efficiency multilayer WSe2 solar cells at low cost.

carrier lifetime↗

Molecular helices as electron acceptors in high-performance bulk heterojunction solar cells

Despite numerous organic semiconducting materials synthesized for organic photovoltaics in the past decade, fullerenes are widely used as electron acceptors in highly efficient bulk-heterojunction solar cells. None of the non-fullerene bulk heterojunction solar cells have achieved efficiencies as high as fullerene-based solar cells. Design principles for fullerene-free acceptors remain unclear in the field. Here we report examples of helical molecular semiconductors as electron acceptors that are on par with fullerene derivatives in efficient solar cells. We achieved an 8.3% power conversion efficiency in a solar cell, which is a record high for non-fullerene bulk heterojunctions. Femtosecond transient absorption spectroscopy revealed both electron and hole transfer processes at the donor–acceptor interfaces. Atomic force microscopy reveals a mesh-like network of acceptors with pores that are tens of nanometres in diameter for efficient exciton separation and charge transport. As a result, this study describes a new motif for designing highly efficient acceptors for organic solar cells.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High 400 °C operation temperature blue spectrum concentration solar junction in GaInN/GaN

Transparent wide gap junctions suitable as high temperature, high flux topping cells have been achieved in GaInN/GaN by metal-organic vapor phase epitaxy. In structures of 25 quantum wells (QWs) under AM1.5G illumination, an open circuit voltage of 2.1 V is achieved. Of the photons absorbed in the limited spectral range of <450 nm, 64.2% are converted to electrons collected at the contacts under zero bias. At a fill factor of 45%, they account for a power conversion efficiency of38.6%. Under concentration, the maximum output power density per sun increases from 0.49 mW/cm{sup 2} to 0.51 mW/cm{sup 2} at 40 suns and then falls 0.42 mW/cm{sup 2} at 150 suns. Under external heating, a maximum of 0.59 mW/cm{sup 2} is reached at 250 °C. Even at 400 °C, the device is fully operational and exceeds room temperature performance. A defect analysis suggests that significantly higher fill factors and extension into longer wavelength ranges are possible with further development. The results prove GaInN/GaN QW solar junctions a viable and rugged topping cell for concentrator photovoltaics with minimal cooling requirements. By capturing the short range spectrum, they reduce the thermal load to any conventional cells stacked behind.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

GaAsP solar cells on GaP/Si with low threading dislocation density

GaAsP on Si tandem cells represent a promising path towards achieving high efficiency while leveraging the Si solar knowledge base and low-cost infrastructure. However, dislocation densities exceeding 10{sup 8} cm{sup −2} in GaAsP cells on Si have historically hampered the efficiency of such approaches. Here, we report the achievement of low threading dislocation density values of 4.0–4.6 × 10{sup 6} cm{sup −2} in GaAsP solar cells on GaP/Si, comparable with more established metamorphic solar cells on GaAs. Our GaAsP solar cells on GaP/Si exhibit high open-circuit voltage and quantum efficiency, allowing them to significantly surpass the power conversion efficiency of previous devices. The results in this work show a realistic path towards dual-junction GaAsP on Si cells with efficiencies exceeding 30%.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Polymer/Polymer Blend Solar Cells Using Tetraazabenzodifluoranthene Diimide Conjugated Polymers as Electron Acceptors

Two n-type semiconducting polymers with alternating arylene (thiophene or selenophene)–tetraazabenzodifluoranthene diimide (BFI) donor–acceptor architecture have been investigated as new electron acceptors in polymer/polymer blend solar cells. The new selenophene-linked polymer, PBFI-S, has a significantly smaller optical band gap (1.13 eV) than the thiophene-linked PBFI-T (1.38 eV); however, both polymers have similar HOMO/LUMO energy levels determined from cyclic voltammetry. Blends of PBFI-T with the thiazolothiazole–dithienylsilole donor polymer (PSEHTT) gave a 2.60% power conversion efficiency (PCE) with a 7.34 mA/cm 2 short-circuit current. In contrast, PBFI-S:PSEHTT blends had a 0.75% PCE with similarly reduced photocurrent and external quantum efficiency. As a result, reduced free energy for charge transfer and reduced bulk electron mobility in PBFI-S:PSEHTT blends compared to PBFI-T:PSEHTT blends as well as significant differences in bulk film morphology are among the reasons for the large loss in efficiency in PBFI-S:PSEHTT blend solar cells.

14 SOLAR ENERGY↗

Characterizing and Improving the Thermal Stability of Organic Photovoltaics Based on Halogen-Rich Non-Fullerene Acceptors

In this work, the thermal stability of inverted, halogen-rich non-fullerene acceptor (NFA)-based organic photovoltaics (OPVs) with MoO x as the hole transporting layer is studied at temperatures up to 80°C. Over time, the power conversion efficiency shows a “check-mark” shaped thermal aging pattern, featuring an early decrease, followed by a long-term recovery. A high Cl concentration at the BHJ/MoO x interface in the thermally aged device is found using energy dispersive X-ray spectroscopy. X-Ray photoelectron spectroscopy shows that the MoO x is chlorinated after thermal aging. With bulk quantum efficiency analysis, we propose an explanation to the check-mark shaped pattern. Inserting a thin C 70 layer between the BHJ and MoO x suppresses the thermal degradation mechanisms, resulting in 3 orders of magnitude increase in device lifetime at 80°C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improving Low-Bandgap Tin–Lead Perovskite Solar Cells via Contact Engineering and Gas Quench Processing

Low-bandgap Sn/Pb ABX 3 perovskites have reached photovoltaic power conversion efficiencies >20%, but they usually have poor stability due to the common use of acidic poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) hole transport layers and A-site cation compositions containing methylammonium (MA). In this work, we develop a process to enable high-quality MA-free Sn/Pb perovskite films grown using a gas quenching process instead of the conventional antisolvents, which provides improved control of the film growth and eliminates wrinkling. Using this method in a device structure with poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) instead of PEDOT:PSS as the hole transport layer, devices can reach efficiencies up to 20% mppt at 0.06 cm 2 and up to 17.5% mppt at 1 cm 2 active area. With these improvements, the devices are characterized for thermal stability and show 80% of the initial power output remaining after 4000 h at 85 °C.

14 SOLAR ENERGY↗

Introducing a Phenyl End Group in the Inner Side Chains of A‐DA'D‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Abstract Power conversion efficiency (PCE) of organic solar cells (OSCs) processed by nonhalogenated solvents is unsatisfactory due to the unfavorable morphology. Herein, two new small molecule acceptors (SMAs) Y6‐Ph and L8‐Ph are synthesized by introducing a phenyl end group in the inner side chains of the SMAs of Y6 and L8‐BO, respectively, for overcoming the excessive aggregation of SMAs in the long‐time film forming processed by nonhalogenated solvents. First, the effect of the film forming time on the aggregation property and photovoltaic performance of Y6, L8‐BO, Y6‐Ph, and L8‐Ph is studied by using the commonly used solvents: chloroform (CF) (rapid film forming process) and chlorobenzene (CB) (slow film forming process). It is found that Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCE from CF‐ to CB‐processed devices owing to the large phase separation, while the Y6‐Ph and L8‐Ph based OSCs show obviously increased PCEs Furthermore, L8‐Ph‐based OSCs processed by nonhalogenated solvento‐xylene (o‐XY) achieved a high PCE of 18.40% with an FF of 80.11%. The results indicate that introducing a phenyl end group in the inner side chains is an effective strategy to modulate the morphology and improve the photovoltaic performance of the OSCs processed by nonhalogenated solvents.

Chemistry↗

Photophysics in emerging photovoltaics

Emerging photovoltaic technologies continue to march forward with power conversion efficiencies of lead halide perovskite solar cells (PSCs) nearing 26%, perovskite-Si tandems now exceeding the single junction detailed balance limit of 33%, and organic solar cells (OSCs) showing efficiencies nearing 20%. Yet, some of the photophysics underpinning PSCs and OSCs remain unresolved. A better understanding will enable more efficient and photostable solar cells and optoelectronic devices in the future. Here, this special issue collects the latest cutting-edge research in the photophysics of PSCs and OSCs, contributed by experts on spectroscopy, theory, device physics, and materials science.

14 SOLAR ENERGY↗

Metal Oxide-Induced Instability and Its Mitigation in Halide Perovskite Solar Cells

Halide perovskite solar cells (PSCs) have emerged as a promising photovoltaic technology for sustainable energy solutions due to their impressive power conversion efficiency and a path to be manufactured by low-cost, high-throughput methods. To reach PSCs’ full potential for practical implementation, it is crucial to solving the issues related to its long-term operational stability. Furthermore, given that PSCs consist of many layers of dissimilar materials which form multiple internal interfaces, it is prudent to examine whether there exist interfacial interactions, most importantly between transport layers and perovskite absorbers, that can trigger device performance and instability. In this perspective, we bring to the attention of the PSC research community the lesser-known interfacial degradation of halide perovskites promoted by contact with metal oxide transport layers and highlight the deleterious effects on the PSCs’ performance and stability. We also discuss various mitigation strategies that have shown promises to achieve high-performing and stable PSCs.

14 SOLAR ENERGY↗