Search NASA⌕ Search

SEARCH · Search NASA

Results for “Printing process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Pushing the Limits of Cubesat Attitude Control: A Ground Demonstration

A cubesat attitude control system (ACS) was designed at the NASA Marshall Space Flight Center (MSFC) to provide sub-degree pointing capabilities using low cost, COTS attitude sensors, COTS miniature reaction wheels, and a developmental micro-propulsion system. The ACS sensors and actuators were integrated onto a 3D-printed plastic 3U cubesat breadboard (10 cm x 10 cm x 30 cm) with a custom designed instrument board and typical cubesat COTS hardware for the electrical, power, and data handling and processing systems. In addition to the cubesat development, a low-cost air bearing was designed and 3D printed in order to float the cubesat in the test environment. Systems integration and verification were performed at the MSFC Small Projects Rapid Integration & Test Environment laboratory. Using a combination of both the miniature reaction wheels and the micro-propulsion system, the open and closed loop control capabilities of the ACS were tested in the Flight Robotics Laboratory. The testing demonstrated the desired sub-degree pointing capability of the ACS and also revealed the challenges of creating a relevant environment for development testin

Sanders, Devon S.↗
NASA NTRS2007

Designing High Speed Printed Circuit Boards Using DxDesigner and Expedition

Mentor's DxDesigner and Expedition schematic capture and printed circuit board tools were chosen to implement a custom high speed signal processing board containing many high pin count Field Programmable Gate Arrays and many high speed serial connections with data rates over 2 Gigasamples/sec. The methodology used to place the parts and route the board involved the interaction of both the DxDesigner and Expedition tools. The basic design philosophy was to specify as much as possible through design constraints at the schematic level. This paper will explore implementing that philosophy in both tools to facilitate part placement and trace routing.

printed circuit boards↗
NASA NTRS2019

Direct-Write Printing on Three-Dimensional Geometries for Miniaturized Detector and Electronic Assemblies

Aerosol Jet Printing (AJP) and other additive electronics technologies will enable new detector assemblies that were not previously possible with traditional assembly processes. This technology has the potential to reduce mass and volume for fabrication and assembly of detector, instrument and electronics concepts by reducing trace widths down to 10 microns, printing on complex geometries, and allowing new concept production. This poster summarizes development efforts of printed interconnects for space applications.

Printed Hybrid Electronics↗
NASA NTRS1973

Welded printed circuit (pc) stick

Printed-circuit stick module has reduced comb technique to six steps, cutting process time by approximately 50%. Method incorporates all type of components into one assembly. It reduces design and fabrication time for 14-lead flat pack to less than four hours and for the 22-lead flat pack to four hours. Average weight of each flat pack is also reduced to 2 g.

Kreis, F.↗
NASA NTRS1991

Qualification of uralane 5750 A/B (LV) for flight applications

Uralane 5750 A/B (LV) is a POLYURETHANE which was to be considered for use as a thin CONFORMAL COATING on printed circuit boards for JPL flight projects. As part of the qualification process several properties of Uralane 5750 A/B (LV) were measured for the as-cured material and after various environmental exposures. The properties that were measured included outgassing i.e. Total Mass Loss (TML) and Vacuum Condensable Mass (VCM) and mass accumulation rates on cold surfaces, Static Elastic Modulus and coefficient of Thermal Expansion (CTE). The Uralane 5750 A/B (LV) that was tested consisted of sheets which varied in both thickness and curing procedures. The environmental exposures consisted of vacuum, thermal and combined thermal vacuum. The physical properties of Uralane 5750 A/B (LV) met the JPL requirements for flight in both the as-cured condition and after environmental exposures.

Lewis, Donald F.↗
NASA NTRS1999

Micromechanics Analysis Code Post-Processing (MACPOST) User Guide

As advanced composite materials have gained wider usage. the need for analytical models and computer codes to predict the thermomechanical deformation response of these materials has increased significantly. Recently, a micromechanics technique called the generalized method of cells (GMC) has been developed, which has the capability to fulfill this -oal. Tc provide a framework for GMC, the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) has been developed. As MAC/GMC has been updated, significant improvements have been made to the post-processing capabilities of the code. Through the MACPOST program, which operates directly within the MSC/PATRAN graphical pre- and post-processing package, a direct link between the analysis capabilities of MAC/GMC and the post-processing capabilities of MSC/PATRAN has been established. MACPOST has simplified the production, printing. and exportation of results for unit cells analyzed by MAC/GMC. MACPOST allows different micro-level quantities to be plotted quickly and easily in contour plots. In addition, meaningful data for X-Y plots can be examined. MACPOST thus serves as an important analysis and visualization tool for the macro- and micro-level data generated by MAC/GMC. This report serves as the user's manual for the MACPOST program.

Goldberg, Robert K.↗
NASA NTRS1992

Infrared Measurement

A Jet Propulsion Laboratory Technical Support Package (TSP) describing a technique for processing data from an infrared radiometer assisted a manufacturer of laminates for printed circuit boards. To reduce emissions and lower the cost of producing prepreg (a continuous glass cloth, or web, impregnated with epoxy resin and partially cured by applying heat), Norplex Oak switched to infrared treating towers. The TSP confirmed the company's computer prediction of heat flux patterns, provided information that allowed the company to modify infrared treaters for consistency, and furnished a basis for development of optimal heater placements. The treaters are now successfully operating at increased speeds with improved product consistency.

Source record↗
NASA NTRS2016

Evaluation of Additively Manufactured Metals for Use in Oxygen Systems Project

Space Launch System, Commercial Resupply, and Commercial Crew programs have published intent to use additively manufactured (AM) components in propulsion systems and are likely to include various life support systems in the future. Parts produced by these types of additive manufacturing techniques have not been fully evaluated for use in oxygen systems and the inherent risks have not been fully identified. Some areas of primary concern in the SLS process with respect to oxygen compatibility may be the porosity of the printed parts, fundamental differences in microstructure of an AM part as compared to traditional materials, or increased risk of shed metal particulate into an oxygen system. If an ignition were to occur the printed material could be more flammable than components manufactured from a traditional billet of raw material and/or present a significant hazards if not identified and rigorously studied in advance of implementation into an oxygen system.

Tylka, Jonathan↗
NASA NTRSDate not supplied

Application of Regolith Polymer Composite FFF Construction in Simulated Lunar Conditions

NASA’s Artemis program has the lofty goal of creating a sustained lunar presence to provide unprecedented opportunities for scientific discovery and to ensure American industry’s access to the unlimited resources and commercial potential in space. To achieve this goal, NASA must incrementally develop and expand its capabilities beyond the short lunar stays of the Apollo program to a robust continued presence with infrastructure and equipment to reduce mission risk by providing safer and more reliable access to the surface, its resources, and protection from the environment. Kennedy Space Center’s Swamp Works Granular Mechanics and Regolith Operations laboratory has partnered with AI SpaceFactory to develop the architectural and structural design of a robotically constructable unpressurized shelter. The shelter, called Lina is designed to protect astronauts and surface assets from radiation, meteoroid impact, moon quakes and thermal gradients. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites was developed. The construction system and associated print parameters are discussed along with the environmental simulation equipment and a summary of test conditions. Test samples were printed in simulated lunar dirty thermal vacuum conditions (~-180 C, ~10-3 torr) and subjected to a series of tests. The resulting strength properties are summarized here, the full details of the material characteristics are provided in a related paper. Lina’s structural design criteria and the resulting initial structure design are detailed in two related papers, this paper presents an update to Lina’s design based on the achieved material strength properties. Finally, a scaled down version of the updated Lina was built on a regolith simulant surface using a novel anchoring technique in simulated lunar vacuum conditions.

lunar infrastructure↗
NASA NTRSDate not supplied

Application of Regolith Polymer Composite Fused Granular Fabrication Construction in Simulated Lunar Conditions

NASA’s Artemis program has the goal of creating a sustained lunar presence to provide unprecedented opportunities for scientific discovery and to ensure industry’s access to the unlimited resources and commercial potential in space. To achieve this goal, NASA must incrementally develop and expand its capabilities beyond the short lunar stays of the Apollo program to a robust continued presence with infrastructure and equipment to reduce mission risk. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory (a.k.a. Swamp Works) has partnered with SpaceFactory and LERA Consulting Structural Engineers to develop the architectural and structural design of a robotically constructable unpressurized shelter. The shelter, called Lunar Infrastructure Asset (LINA), is designed to protect astronauts and surface assets from radiation, meteoroid impact, thermal gradients, and to withstand moonquakes. A Fused Granular Fabrication (FGF) construction process using regolith polymer composites was developed. The construction system and associated print parameters are discussed along with the environmental simulation equipment and a summary of test conditions. Test samples were printed in dirty thermal vacuum conditions (~10-3 torr, ~-200 °C,) and subscale versions of LINA were printed on a regolith simulant substrate in vacuum (~10-4 torr). Full scale LINA design optimization, simulation, and construction concept of operations are discussed.

lunar infrastructure↗
NASA NTRSDate not supplied

Selection, Production and Properties of Regolith Polymer Composite for Lunar Construction

NASA’s Artemis program has the goal of creating a sustained lunar presence to provide unprecedented opportunities for scientific discovery and to ensure industry’s access to the unlimited resources and commercial potential in space. To achieve this goal, NASA must incrementally develop and expand its capabilities beyond the short lunar stays of the Apollo program to a robust continued presence with infrastructure and equipment to reduce mission risk. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory (a.k.a. Swamp Works) has partnered with SpaceFactory and LERA Consulting Structural Engineers to develop the architectural and structural design of a robotically constructable unpressurized shelter. The shelter, called Lunar Infrastructure Asset (LINA), is designed to protect astronauts and surface assets from radiation, meteoroid impact, thermal gradients, and to withstand moonquakes. A Fused Granular Fabrication (FGF) construction process using regolith polymer composites was developed. The construction system and associated print parameters are discussed along with the environmental simulation equipment and a summary of test conditions. Test samples were printed in dirty thermal vacuum conditions (~10-3 torr, ~-200 °C,) and subscale versions of LINA were printed on a regolith simulant substrate in vacuum (~10-4 torr). Full scale LINA design optimization, simulation, and construction concept of operations are discussed.

lunar infrastructure↗
NASA NTRSDate not supplied

Understanding the Feasibility of MAB Phase Structures for Lunar Applications

During the ten-week internship, my work focused on synthesis, characterization, and tailoring the flowability of the MAB phase powders for improving the surface finish and decreasing porosity of 3D-printed MAB phase structures. My mentor for the project was Dr. Samuel Hocker from NASA Langley and my faculty advisor was Dr. Surojit Gupta from the University of North Dakota. I also collaborated with Daniel Trieff from the University of North Dakota in developing characterization paradigm of 3D printed samples. The microencapsulation was performed via novel solvent casting-based microencapsulation process pioneered in UND, wherein a polymer (PLA, PHA) was dissolved into dichloromethane and precipitated onto the surface of the MoAlB particles. Two 100mL samples of microencapsulated powder was outsourced to Particle Technology Labs for flowability testing along with a 100mL control sample to determine if microencapsulation is a valid method for improving the flowability. The microencapsulated powders were characterized using SEM, Differential Scanning Calorimetry, and optical microscopy. The SEM images showed no change between the pure and microencapsulated powders. The optical microscopy analysis indicated a reduction in reflectivity for the PLA microencapsulated powders as well as hydrophobic properties. Both results suggest that microencapsulation was successful as PLA is a hydrophobic polymer and the change in reflectivity could be a result of the light being dispersed through the polymer coating. A reflectivity analysis will be done to bring more perspective to these observations. If powder flowability is improved, then the project will move forward with testing the printability of the microencapsulated powders and characterizing the structures using the designed characterization protocol. We are waiting for the DSC results. The characterization protocol for the 3D-printed MAB structures included a visual inspection of the plates to rule out any samples that had spalled or delaminated, optical microscopy to document surface features, porosity, and decomposition, and cleaning of the plates using an ultrasonic bath in preparation for SEM, EDS, and profilometry analyses.

MAB Phase↗
NASA NTRS2014

Printable Spacecraft: Flexible Electronic Platforms for NASA Missions

Why printed electronics? Why should NASA use printed electronics to make a spacecraft? Three words provide the answer: universal, impactful, progressive. The technology is universal because the applications it can affect are broad and diverse from simple sensors to fully functional spacecraft. The impact of flexible, printed electronics range from straightforward mass, volume and cost savings all the way to enabling new mission concepts. The benefits of the technology will become progressively larger from what is achievable today so that investments will pay dividends tomorrow, next year and next decade. We started off three years ago asking the question can you build an entire spacecraft out of printed electronics? In other words, can you design and fabricate a fully integrated, electronic system that performs the same end-to-end functions of a spacecraft - take scientific measurements, perform data processing, provide data storage, transmit the data, powers itself, orients and propels itself - all out of thin flexible sheets of printed electronics? This "Printable Spacecraft" pushes the limits of printed flexible electronics performance. So the answer is yes, more or less. In our studies for the NIAC (NASA Innovative Advanced Concepts) program, we have explored this question further, to explain more completely what "more or less" means and to outline what is needed to make the answer a definitive "yes". Despite its appealing "Flat Stanley"-like (a book series by Jeff Brown) qualities, making a Printable Spacecraft is not as easy as flattening the Cassini spacecraft with a bulletin board, as was Stanley Lamchop's fate. But, if NASA invests in the design challenges, the materials challenges, the performance challenges of printed electronics, it might find itself with a spacecraft that can enable as many adventures and advantages as Flat Stanley including putting it in an envelope and mailing it to the planet of your choice. You just have to let your imagination take over. In this report we document the work of the Phase 2 Printable Spacecraft task conducted under the guidance and leadership of the NIAC program. In Phase One of the NIAC task entitled "Printable Spacecraft", we investigated the viability of printed electronics technologies for creating multi-functional spacecraft platforms. Mission concepts and architectures that could be enhanced or enabled with this technology were explored. In Phase 2 we tried to answer the more practical questions such as can you really build a multi-functional printed electronic spacecraft system? If you do, can it survive the space environment? Even if it can, what benefit does a printable system provide over a traditional implementation of a spacecraft?

Materials↗
NASA NTRS2010

Inexpensive Implementation of Many Strain Gauges

It has been proposed to develop arrays of strain gauges as arrays of ordinary metal film resistors and associated electronic readout circuitry on printed circuit boards or other suitable substrates. This proposal is a by-product of a development of instrumentation utilizing metal film resistors on printed-circuit boards to measure temperatures at multiple locations. In the course of that development, it was observed that in addition to being sensitive to temperature, the metal film resistors were also sensitive to strains in the printed-circuit boards to which they were attached. Because of the low cost of ordinary metal film resistors (typically <$0.01 apiece at 2007 prices), the proposal could enable inexpensive implementation of arrays of many (e.g., 100 or more) strain gauges, possibly concentrated in small areas. For example, such an array could be designed for use as a computer keyboard with no moving parts, as a device for sensing the shape of an object resting on a surface, or as a device for measuring strains at many points on a mirror, a fuel tank, an airplane wing, or other large object. Ordinarily, the effect of strain on resistance would be regarded as a nuisance in a temperature-measuring application, and the effect of temperature on resistance would be regarded as a nuisance in a strain-measuring application. The strain-induced changes in resistance of the metal film resistors in question are less than those of films in traditional strain gauges. The main novel aspect of present proposal lies in the use of circuitry affording sufficient sensitivity to measure strain plus means for compensating for the effect of temperature. For an array of metal film resistors used as proposed, the readout circuits would include a high-accuracy analog-to-digital converter fed by a low noise current source, amplifier chain, and an analog multiplexer chain. Corrections would be provided by use of high-accuracy calibration resistors and a temperature sensor. By use of such readout circuitry, it would be possible to read the resistances of as many as 100 fixed resistors in a time interval of 1 second at a resolution much greater than 16 bits. The readout data would be processed, along with temperature calibration data, to deduce the strain on the printed-circuit board or other substrate in the areas around the resistors. It should also be possible to also deduce the temperature from the readings.

Berkun, Andrew C.↗
NASA NTRS2004

Printed Circuit Board Design (PCB) with HDL Designer

Contents include the following: PCB design with HDL designer, design process and schematic capture - symbols and diagrams: 1. Motivation: time savings, money savings, simplicity. 2. Approach: use single tool PCB for FPGA design, more FPGA designs than PCB designers. 3. Use HDL designer for schematic capture.

Winkert, Thomas K.↗
NASA NTRS1979

Array Automated Assembly, Phase 2

The baseline process sequence using nontextured square wafers was integrated. Difficulties encountered include: (1) replacement of the N-250 spray on diffusion source with PX-10 source; and (2) modification of the firing for printed silver and aluminum contracts is required to accommodate the change of wafer size and shape. Results indicate that the cells processed through the entire process sequence except laser scribe and spray on AR coating indicate the process sequence is feasible. Greater cell conversion efficiency is presented.

Taylor, W. E.↗
NASA NTRS1978

Array Automated Assembly Task Low Cost Silicon Solar Array Project, Phase 2

Progress in the development of solar cells and module process steps for low-cost solar arrays is reported. Specific topics covered include: (1) a system to automatically measure solar cell electrical performance parameters; (2) automation of wafer surface preparation, printing, and plating; (3) laser inspection of mechanical defects of solar cells; and (4) a silicon antireflection coating system. Two solar cell process steps, laser trimming and holing automation and spray-on dopant junction formation, are described.

Rhee, S. S.↗
NASA NTRS2016

Nanomaterial Based Sensors for NASA Missions

Nanomaterials such as carbon nanotubes (CNTs), carbon nanofibers (CNFs), graphene and metal nanowires have shown interesting electronic properties and therefore have been pursued for a variety of space applications requiring ultrasensitive and light-weight sensor and electronic devices. We have been pursuing development of chemical and biosensors using carbon nanotubes and carbon nanofibers for the last several years and this talk will present the benefits of nanomaterials these applications. More recently, printing approaches to manufacturing these devices have been explored as a strategy that is compatible to a microgravity environment. Nanomaterials are either grown in house or purchased and processed as electrical inks. Chemical modification or coatings are added to the nanomaterials to tailor the nanomaterial to the exact application. The development of printed chemical sensors and biosensors will be discussed for applications ranging from crew life support to exploration missions.

sensors↗