Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESIDUAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Estimation of uncertainty for contour method residual stress measurements

This paper describes a methodology for the estimation of measurement uncertainty for the contour method, where the contour method is an experimental technique for measuring a two-dimensional map of residual stress over a plane. Random error sources including the error arising from noise in displacement measurements and the smoothing of the displacement surfaces are accounted for in the uncertainty analysis. The output is a two-dimensional, spatially varying uncertainty estimate such that every point on the cross-section where residual stress is determined has a corresponding uncertainty value. Both numerical and physical experiments are reported, which are used to support the usefulness of the proposed uncertainty estimator. The uncertainty estimator shows the contour method to have larger uncertainty near the perimeter of the measurement plane. For the experiments, which were performed on a quenched aluminum bar with a cross section of 51 × 76 mm, the estimated uncertainty was approximately 5 MPa (σ/E = 7 · 10⁻⁵) over the majority of the cross-section, with localized areas of higher uncertainty, up to 10 MPa (σ/E = 14 · 10⁻⁵).

42 ENGINEERING↗

Superhard behaviour, low residual stress, and unique structure in diamond-like carbon films by simple bilayer approach

Simple bilayer approach is proposed for synthesizing hard and superhard diamond-like carbon (DLC) coatings with reduced residual stress. For this, M/DLC bilayer (M = Ti and Cu) structures are grown using hybrid system involving radio frequency (RF)-sputtering and RF-plasma enhanced chemical vapor deposition techniques. Ti/DLC bilayer deposited at negative self bias of 100 V shows superhard behaviour with hardness (H) as 49 GPa. Cu/DLC bilayer grown at self bias of 100 V exhibits hard behaviour with H as 22.8 GPa. The hardness of Ti/DLC (Cu/DLC) bilayer gets changed from superhard (hard) to hard (moderate hard) regime, when the self bias is raised to 300 V. Residual stress in Ti/DLC (Cu/DLC) bilayer is found to be significantly low that varies in the range of 1 GPa-1.65 GPa (0.8 GPa-1.6 GPa). The microstructure and morphology are studied by Raman spectroscopy, scanning electron microscopy (SEM), and atomic force microscopy (AFM). SEM and AFM pictures reveal the creation of nanostructured features in the deposited bilayers. Raman, SEM, and AFM analyses are correlated with the nano-mechanical properties. Owing to excellent nano-mechanical properties, these bilayers can find their direct industrial applications as hard and protective coatings.

36 MATERIALS SCIENCE↗

Measurement and prediction of through-section residual stresses in the manufacturing sequence of bearing components

Through-section residual stresses in an asymmetric, thin-walled tapered bearing component were non-destructively studied via neutron diffraction after soft machining, heat treatment and hard turning. Two-dimensional area maps revealed non-uniform distributions of stress fields in both the thinnest and thickest sections of the component, indicating that the entire processing sequence plays a vital role — not only in distortion, but in the final stress state as well. Here, a computational model was developed to further understand the extent of the distortion induced in bearing components as a result of process variables in the manufacturing sequence.

36 MATERIALS SCIENCE↗

Measuring multiple residual-stress components using the contour method and multiple cuts

The conventional contour method determines one component of stress over the cross section of a part. The part is cut into two, the contour of the exposed surface is measured, and Bueckner's superposition principle is analytically applied to calculate stresses. In this paper, the contour method is extended to the measurement of multiple stress components by making multiple cuts with subsequent applications of superposition. The theory and limitations are described. The theory is experimentally tested on a 316L stainless steel disk with residual stresses induced by plastically indenting the central portion of the disk. The stress results are validated against independent measurements using neutron diffraction. The theory has implications beyond just multiple cuts. The contour method measurements and calculations for the first cut reveal how the residual stresses have changed throughout the part. Subsequent measurements of partially relaxed stresses by other techniques, such as laboratory x-rays, hole drilling, or neutron or synchrotron diffraction, can be superimposed back to the original state of the body.

36 MATERIALS SCIENCE↗

Impact of surface and residual stresses and electro-/magnetostatic axial loading on the suspended nanomechanical based mass sensors: A theoretical study

Suspended nanomechanical mass sensors are capable to detect the attached molecules or particles through the shifts in the resonant frequencies. However, surface and residual stresses can as well cause a shift of the sensor resonances. As result, understanding the impact of stresses in an accuracy and sensitivity of the mass sensors is a fundamental requirement for a rigorous analysis of experimental data. Here, we present a detailed theoretical study of the suspended nanomechanical resonators and mass sensors under axial load created by surface (residual) stresses or electrostatic (magnetostatic) forces. Easily accessible formulas allowing one either to accurately predict the resonant frequencies of the beam under tension/compression or to disentangle the effects of stresses (axial forces) and the molecule mass on the frequency shift of the suspended mass sensors have been derived. A dimensionless parameter enabling us a simple characterization of the device vibrational regime (i.e., beam, string, or beam-to-string transition) has been identified. Based on the results, the applicability limits of the classical beam theory with and without axial loading have been found. We also show that tuning the beam resonant frequencies enhances the mass sensitivity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Residual stress and bending strength of ZnO films deposited on polyimide sheet by RF sputtering system

Zinc oxide (ZnO) films were deposited on a soft polyimide sheet substrate by radio frequency sputtering with a ZnO powder target, and the films' crystal orientations and residual stress were investigated using x-ray diffraction as a function of substrate temperature. C-axis oriented ZnO films were achieved using this ZnO powder target method. The ZnO films exhibited high compressive residual stresses between −0.7 and −1.4 GPa. Finally, the authors examined the strength of the obtained film by applying tensile bending loads. No cracks were observed on the surfaces of the ZnO films after a bending test using cylinders with diameters >25 mm. After a bending test using a cylinder with a diameter of 19 mm, large cracks were formed on the films. Therefore, the authors concluded that the tensile bending strength of the obtained films was greater than ∼420 MPa.

42 ENGINEERING↗

Measurement of Residual Stresses by X-ray Diffraction Near Simulated Heat Affected Zones in Austenitic Stainless Steels

Simulated heat-affected zones (HAZs) were made in austenitic stainless steel specimens using a Gleeble. The samples were heated to temperatures as high as 1100°C by computer controlled resistance heating. By controlling the heating rate, maximum temperature, and cooling rate, a wide range of residual stresses were introduced in the specimens. Stress measurements were made using X-ray diffraction. It was found that significant stress gradients were produced in the simulated HAZs, and that all stresses were compressive in nature, both in the longitudinal and transverse directions. These results are not representative of the residual stresses determined in the HAZs of real welds, thus calling into question some aspects of the role of the Gleeble in such simulations.

36 MATERIALS SCIENCE↗

In-Situ Calibrated Modeling of Residual Stresses Induced in Machining under Various Cooling and Lubricating Environments

Although many functional characteristics, such as fatigue life and damage resistance depend on residual stresses, there are currently no industrially viable ‘Digital Process Twin’ models (DPTs) capable of efficiently and quickly predicting machining-induced stresses. By leveraging advances in ultra-high-speed in-situ experimental characterization of machining and finishing processes under plane strain (orthogonal/2D) conditions, we have developed a set of physics-based semi-analytical models to predict residual stress evolution in light of the extreme gradients of stress, strain and temperature, which are unique to these thermo-mechanical processes. Initial validation trials of this novel paradigm were carried out in Ti-6Al4V and AISI 4340 alloy steel. A variety dry, cryogenically cooled and oil lubricated conditions were evaluated to determine the model’s ability to capture the tribological changes induced due to lubrication and cooling. The preliminarily calibrated and validated model exhibited an average correlation of better than 20% between the predicted stresses and experimental data, with calculation times of less than a second. Based on such fast-acting DPTs, the authors envision future capabilities in pro-active surface engineering of advanced structural components (e.g., turbine blades).

36 MATERIALS SCIENCE↗

Residual Stress Distribution and Microstructure of a Multiple Laser-Peened Near-Alpha Titanium Alloy

Laser peening without coating (LPwC) was performed on a Ti-2.5 Cu alloy with multiple passes (1, 3 and 5), using a Nd:YAG laser (1064 nm) at a constant overlap rate of 70% and power density of 6.7 GW cm{sup −2}. Hardness and residual stress profiles indicated thermal softening near the surface (< 100 μm) and bulk softening due to adiabatic heating. Maximum hardness (235 HV at 500 μm) and maximum residual stress (− 890 MPa at 100 μm) were observed for LPwC with 1 pass. Surface roughness and surface 3-D topography imaging showed that the surface roughness increased with the increase in the number of passes. XRD results indicated no significant β phases. However, peak shifts, broadening and asymmetry were observed and interpreted based on dislocation activity. Microstructures indicated no melting or resolidification or refinement of grains at the surface. Twin density was found to increase with the increase in the number of passes.

36 MATERIALS SCIENCE↗

Residual stresses in functionally graded thermal barrier coatings

Functionally graded materials offer potential as a solution to the premature failure of thermal barrier coatings due to thermal residual stresses, however this solution has not been fully evaluated to date. An analytical methodology based on the bending of plates has been used to model the residual stress distribution through the layers of a functionally graded (FG) cermet top coat-bond layer-substrate system after cooling from a high deposition temperature. The model is then applied to two material systems with different trends in variation in the coefficient of thermal expansion from the substrate to the top coat layer. Increasing the number of layers reduces the discrete stress variations across the interfaces through the FG layers and reduces the propensity of interfacial cracking. While the stress in the top coat is always compressive for the Inconel substrate, the stress in the top coat is tensile in nature for the steel substrate when the ceramic volume fraction in the functionally graded layers is low. The stress in the top coat gradually becomes compressive with an increasing volume fraction of ceramic in the functionally graded top coat. The curvature of the TBC system follows a similar trend and changes its sign with increasing ceramic content for the steel substrate. In conclusion, the effect of the number of layers on the curvature gradually diminishes and the curvature becomes constant beyond only a few layers.

36 MATERIALS SCIENCE↗

Simultaneous determination of the residual stress, elastic modulus, density and thickness of ultrathin film utilizing vibrating doubly clamped micro-/nanobeams

Measurement of ultrathin film thickness and its basic properties can be highly challenging and time consuming due to necessity of using several very sophisticated devices. Here, we report an easy accessible resonant based method capable to simultaneously determinate the residual stress, elastic modulus, density and thickness of ultrathin film coated on doubly clamped micro-/nanobeam. We show that a general dependency of the resonant frequencies on the axial load is also valid for in-plane vibrations, and the one depends only on the considered vibrational mode. As a result, we found that the film elastic modulus, density and thickness can be evaluated from two measured in-plane and out-plane fundamental resonant frequencies of micro-/nanobeam with and without film under different prestress forces. Whereas, the residual stress can be determined from two out-plane (in-plane) measured consecutive resonant frequencies of beam with film under different prestress forces without necessity of knowing film and substrate properties and dimensions. Moreover, we also reveal that the common uncertainties in force (and thickness) determination have a negligible (and minor) impact on the determined film properties. The application potential of the present method is illustrated on the beam made of silicon and SiO{sub 2} with deposited 20 nm thick AlN and 40 nm thick Au thin films, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of a self-equilibrium cutting strategy for the contour method of residual stress measurement

An assessment of cutting-induced plasticity (CIP) is performed, by finite element (FE) prediction of the plastic strain accumulation along the cut tip when the EDM wire sections the NeT TG4 weld benchmark specimen along two cutting directions. The first direction corresponds to a conventional (C) cutting strategy, whereby the EDM wire cuts through the thickness of the weld specimen and travels in a direction transverse to the weld. The second direction corresponds to a self-equilibrating cutting (SE) strategy, whereby the EDM wire cuts across the transverse direction of the weld specimens and travels through the thickness of the plate. The cutting thus progresses simultaneously through the compression-tension-compression regions of present weld residual stress (WRS) field. This type of cutting strategy is believed to minimize the CIP by minimising residual stress redistribution during cutting, due to stress equilibration across the sectioned material. The simulated cutting procedures are conducted under a range of clamping conditions to assess whether mechanical restraint has a primary or secondary influence on CIP accumulation. Both predictions of CIP and the resultant back-calculated WRS demonstrate that (i) mechanical restraint is the primary variable influencing CIP development, and (ii) under no circumstance does a self-equilibrating cutting strategy perform significantly better than a conventional cutting approach. Furthermore, the reason that self-equilibrating cuts are not effective is illustrated by calculating the Mode I (K I ) stress intensity factor (SIF) along the cut tip, and correlating trends in K I to CIP development.

36 MATERIALS SCIENCE↗

Ion-beam radiation-induced Eshelby transformations: The mean and variance in hydrostatic and shear residual stresses

Ion beam plays a pivotal role in ion implantations and the fabrication of nanostructures. However, there lacks a quantitative model to describe the residual stresses associated with the ion-beam radiation. Radiation-induced residual stress/transformation strain have been mostly recognized in the hydrostatic sub strain space. Here, in this study, we use molecular dynamics (MD) simulations to show that the response of a material to irradiation is generally anisotropic that depends on the ion-beam direction, and should be described using tensorial quantities. We demonstrate that accelerator-based ion beam irradiation, combined with the intrinsic lattice anisotropy and externally induced anisotropy (such as anisotropic mechanical loadings), causes radiation-actuated shear transformation strains in addition to hydrostatic expansion. We map out these complex correlations for several materials. Radiation-induced defects are shown to be responsible for residual shear stresses in the manner of Eshelby inclusion transformation. We propose such tensorial response model should be considered for accurate nanoscale fabrication using ion-beam irradiation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Residual stresses distribution, correlated with bending tests, within explosively welded Ti gr. 2/A1050 bimetals

Highlights: • Ti gr.2/A1050 clad was slightly affected by the explosive welding since negative sign values of stress tensor were detected. • Upon bending higher negative compression stresses were detected in this area. • Twins morphology changed from parallel to cross-shaped arrangement as a consequence of bending. • The compressive twinning was the dominant system before and after three point bending. - Abstract: Synchrotron radiation and XRD{sup 2} method were used to investigate the residual stress distribution before and after three point bending tests within an explosively welded composite composed of two light metals, namely: Ti gr. 2 and A1050. The analysis has shown that the bimetal is slightly affected by the explosive welding process since negative sign values of stress tensor were detected only in the immediate vicinity of interface of Ti gr. 2 characterized by a width of about 0.25 mm. Upon bending higher negative compression stresses are detected in this area as the σ{sub 11} value changes from −500 MPa to −1200 MPa. Additionally, the analysis of microstructure has revealed significant changes in twins morphology with primary and conjugate twinning before and after bending, respectively. However, the compressive twinning was the dominant system in both cases. Bending has changed the initial bimodal texture developing more spread basal components towards the transverse direction. The sample surface has been also significantly affected as the presence of compressive residual stress (−500 MPa) after bending was measured.

36 MATERIALS SCIENCE↗

Residual stress stability in fiber textured stoichiometric AlN film grown using rf magnetron sputtering

The authors report on the stability of mechanical stress with aging and thermal cycling for columnar structured stoichiometric and homogeneous aluminum nitride thin films grown using radio frequency magnetron sputtering technique. The set of deposition parameters were optimized for the best possible orientation of crystallites in the c axis of compositionally stoichiometric films. The as-grown stress in the slightly nitrogen-rich film does not change when exposed to the atmosphere following deposition, while that in the nitrogen-deficient film, it changes due to oxidation. Additionally, the magnitude of as-grown stress has been found to depend on the substrate material in addition to the deposition parameters. The stress in the film grown on a Si(001) substrate was more tensile than in the film grown on a semi-insulating (si) GaAs(001) substrate for a given set of deposition parameters. Furthermore, the stress in the film grown on Si decreased with temperature, while that on si GaAs increased, indicating the thermally induced stress component to be the major component in the residual stress. Upon subsequent cooling the stress changes in both substrates followed the same path as of heating, thus exhibiting no hysteresis with thermal cycles between room temperature and 400 deg. C.

36 MATERIALS SCIENCE↗

Residual Stresses and Plastic Deformation in Self-Pierce Riveting of Dissimilar Aluminum-to-Magnesium Alloys

In this study, the complex relationship between deformation history and residual stresses in a magnesium-to-aluminum self-pierce riveted (SPR) joint is elucidated using numerical and experimental approaches. Non-linear finite element (FE) simulations incorporating strain rate and temperature effects were performed to model the deformation in the SPR process. In order to accurately capture the deformation, a stress triaxiality-based damage material model was employed to capture the sheet piercing from the rivet. Strong visual comparison between the physical cross-section of the SPR joint and the simulation was achieved. To aid in understanding of the role of deformation in the riveting process and to validate the modeling approach, several experimental measurements were conducted. To quantify the plastic deformation from the piercing of the rivet, micro hardness mapping was performed on a cross-section of the SPR joint. The FE model showed very strong correlation to the experimental hardness mapping results suggesting the nonlinear model captured the plastic deformation with high accuracy. To measure the elastic residual stresses in the SPR joint, neutron and x-ray diffraction mapping techniques were conducted and in general, the FE model correlated well to the trends and magnitudes of the elastic stresses. While some error occurred in between the model and the neutron and x-ray diffraction results, the numerical approach developed in this study shows potential as a tool for understanding SPR behavior as well as optimizing the process parameters.

36 MATERIALS SCIENCE↗

Residual Stresses in SAVY 4000 and Hagan Container Bodies

Chloride-induced stress corrosion cracking (SCC) has been investigated as a potential failure mechanism for the SAVY 4000 and the Hagan containers used to store plutonium-bearing materials at Los Alamos National Laboratory. This report discusses the regions of the container bodies most susceptible to SCC and the magnitude of the residual stresses in those regions. Boiling MgCl2 testing indicated that for both containers the region near the top weld was most susceptible to SCC. The Hagan showed through wall cracking after 22-24 hours of exposure both parallel (axial stresses) and perpendicular (hoop stresses) to the weld. The SAVY 4000 container showed significant cracking above and below the weld after 47 hours of exposure but there was no visual evidence of a through wall crack and the cracks did not leak water. Two through wall holes formed in the bottom of the SAVY 4000 container after 44-46 hours of exposure. For both containers, average “through wall” residual stresses were determined from hole drilling data 4 mm below the weld. In the Hagan body, average tensile hoop stresses were 194 MPa and average compressive axial stresses were -120 MPa. In the SAVY 4000 body, average compressive hoop stresses were 11 MPa and average tensile axial stresses were 25 MPa. Results suggest that because the Hagan container exhibited through wall cracking in a shorter time in boiling MgCl2 and had the higher average tensile stress, 194 MPa hoop stress, it is more susceptible to SCC than the SAVY 4000 container.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ASSESSMENT OF RESIDUAL STRESSES ON U10MO ALLOY BASED MONOLITHIC MINI-PLATES DURING HOT ISOSTATIC PRESSING

This article presents an assessment of the residual stress field on U10Mo alloy based monolithic fuel plates and their elasto-plastic response to the thermo-mechanical fabrication process. Monolithic plate-type fuel for research and test reactors is a new fuel form proposed and developed by Idaho National Laboratory (INL) to accomplish higher uranium densities in the reactor core and allow multi-fold reduction of fuel enrichment. Identification of the 3D residual field is critical for benchmarking the new design and understanding the overall performance of the new plate-type fuels. To define fuel-cladding stress-strain characteristics, a new thermo-mechanical finite element model was developed. Material properties at high temperatures and material plasticity were considered carefully to improve the accuracy as the Hot Pressing temperature reaches the melting temperature of the cladding material. By using elasto-thermo-plastic material models, it was determined that the cladding material (AL6061-TO) is exposed to tensile stress field and exceeds its proportional limits, while the fuel foil (U10Mo) is under compression and remains below its yield limit. It was shown that the residual stresses would govern the overall behavior of the plates, and therefore, should not be neglected. In particular, the simulations have revealed the existence of stress gradients at the fuel/cladding interface, thus emphasizing the necessity of excellent bonding quality at the bond region for mechanical endurance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗