Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rearrangement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Microstructure and CPO evolution of dynamically recrystallized olivine during complex deformation conditions: a full-field numerical modeling approach

The rheological properties of mantle rocks are strongly dependent on their crystallographic preferred orientation (CPO). Olivine CPO, defined by the orientation of seismically fast [100] axes parallel to flow direction, is also thought to be a dominant contributor to seismic anisotropy in the Earth's upper mantle. However, the amount of deformation needed to overprint a new CPO on a pre-existing fabric and the impact of the inherited CPOs on the transient microstructure evolution, remain unknown. This study employs a full-field numerical approach (VPFFT-ELLE) to explore the dynamic recrystallization and microstructural evolution of olivine polycrystalline aggregates under complex deformation conditions. We test four combinations of successive pure shear and simple shear boundary conditions. Findings indicate that inherited CPOs influence subsequent deformation in a manner dependent on the kinematic relationship between successive stages. In all cases, a minor strain increment (ε ∼0.3–0.6) is sufficient to erase the previous microstructure and CPO. However, when deformation conditions change dramatically (e.g., stretching direction changes orthogonally), the intensity of the new CPO developed is significantly lower and strain distribution are specially altered. During a transient strain stage, pre-existing microstructures undergo extensive reworking, especially when deformation conditions are changed dramatically, such as switching from simple shear to a pure shear condition with a parallel shortening direction relative to the stretching direction. We estimate the significance of these results in interpreting observations of seismic velocity anisotropy, concluding that P-wave seismic anisotropy is significantly and positively correlated with the evolution of olivine CPO with deformation history. This research underscores the transient nature of microstructural rearrangement in olivine aggregates and the necessity for caution in interpreting seismic anisotropy in regions with complex deformation histories, as inherited CPOs can influence current fabric development and induce deviation to the present deformation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surpassing the stiffness-extensibility trade-off of elastomers via mastering the hydrogen-bonding clusters

The current paradigm of elastomer design typically falls into the trade-off between stiffness and extensibility. With a few reports on circumventing this trade-off behavior, e.g., increasing Young's modulus without sacrificing extensibility, the design principles to achieve improvements in both stiffness and extensibility have rarely been demonstrated. Herein, with a model system, i.e., cross-linked polydimethylsiloxane (PDMS) network, we demonstrate two approaches that can surpass the stiffness-extensibility trade-off and provide significant improvement in both parameters. Such an achievement is realized by introducing rationally arranged hydrogen-bonding units, i.e., ureidopyrimidone (UPy), leading to simultaneously improved Young's modulus and extensibility up to 158 and 3 times, respectively. Based on the experimental results, we also propose a microscopic picture of network rearrangement during the stretching process. Moreover, using this picture, we further improved Young's modulus of the elastic network without affecting its extensibility through mastering the distribution/topology of UPy clusters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Machine learning bridges local static structure with multiple properties in metallic glasses

A long-standing challenge in the metallic glass (MG) community has been how to quantitatively gauge the influence of the intricate local packing environment on the response (such as the propensity for atomic rearrangement) of the atomic configuration to external stimuli. Here we establish this structure–property relation by representing the complex amorphous structure using a single, flexibility-orientated structural quantity. This structural flexibility (SF) couples to a bona fide structural representation, the pair distribution function (PDF) of individual atoms, through a weighting function that reflects what matters in the static atomic configuration to dynamic responses. Machine learning is used, employing microscopic flexibility volume as the supervisory signal, to establish via direct regression an optimized weighting vector, which is proven robust for all quenching rates, deformation conditions, and different compositions in a given (e.g., Cu x Zr 100-x ) alloy system. Additionally, the SF is evaluated solely from the particle positions (PDF), for any structure variation, from the atomic scale up to sample average. Strong correlations are demonstrated between SF and a broad range of properties, including vibrational, diffusional, as well as elastic and plastic relaxation responses.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Catalysts by pyrolysis: Direct observation of transformations during re-pyrolysis of transition metal-nitrogen-carbon materials leading to state-of-the-art platinum group metal-free electrocatalyst

Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-Nx sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. Finally, these observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Polymeric membranes for CO 2 separation and capture

Over the past decade, CO 2 separation and capture have become the new bandwagon for polymer science and membrane research. This review presents the fundamentals of CO 2 /gas separation in polymeric membranes and discusses how these principles underpin opportunities and challenges for post-combustion carbon capture (CO 2 /N 2 ), hydrogen purification (CO 2 /H 2 ), and natural gas and biogas sweetening (CO 2 /CH 4 ). Emerging polymeric membrane materials are discussed, including a few polymers containing a high content of polar functional groups (i.e., ether oxygen-rich polymers and polymeric ionic liquids), shape-persisting glassy polymers (i.e., perfluoropolymers, thermally rearranged polymers, iptycene-containing polymers), and reactive polymers featuring facilitated transport. Moreover, the promising candidates for each CO 2 separation application are highlighted. Lastly, the permeability-selectivity data reviewed were plotted against their 2008 and 2019 upper bounds.

08 HYDROGEN↗
DOE OSTI2020

A continuum damage mechanics (CDM) based Wilshire model for creep deformation, damage, and rupture prediction

In this report, a new constitutive model is derived that combines the Wilshire equations with continuum damage mechanics (CDM) to enable the long-term prediction of creep deformation, damage, and rupture. The Wilshire equations have been demonstrated to accurately extrapolate the stress-rupture, minimum-creep-strain-rate, and time-to-strain of various alloys across decade of life. Recently, the time-to-creep-strain equation has been rearranged to predict creep deformation curves; however, the resulting equation is difficult to calibrate and does not track damage. The CDM-based Sinh constitutive model accurately predicts creep deformation, damage, and stress-rupture for a variety of alloys; however, it lacks an explicit description of stress and temperature co-dependence which limits interpolation and extrapolation ability. In this study, the Wilshire and the CDM-based Sinh equations are combined to create the “WCS” model. The WCS model combines the best features of each model while eliminating their deficiencies. Experimental data for alloy P91 is gathered and the WCS model is calibrated to the data. The WCS model accurately predicts the stress rupture, minimum-creep-strain-rate, creep deformation, and damage of alloy P91 across the experimental stress and temperature range as well as consistency in parametric simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Infinitely rugged intra-cage potential energy landscape in metallic glasses caused by many-body interaction

The absence of translational symmetry in glassy materials poses a significant challenge in establishing effective structure-property relationships in real space. Consequently, the potential energy landscape (PEL) in phase space is widely utilized to comprehend the complex phenomena in glasses. The classical PEL features a two-scale profile comprising mega-basins and sub-basins, corresponding to α-relaxations (e.g. glass transition) and β-relaxations (e.g. local cage-breaking atomic rearrangements), respectively. Recent studies, however, reveal that sub-basins are not smooth and contain finer structures, the origins of which remain elusive. Here we probe the smoothness of sub-basin bottoms in glasses' PEL by introducing small intra-cage cyclic loading and then measuring the net changes in atomic-level stresses. Compared to glasses with pair interaction, glasses with many-body interaction exhibit orders-of-magnitude larger and loading-dependent stress changes even before the first cage-breaking event takes place, which reflect much more feature-rich sub-basins. We further demonstrate this stark contrast stems from the spatial distribution of individual atom's constraining force field. Specifically, at vanishing perturbations, many-body interactions disrupt the positive-definite synchrony in energy variations of the perturbed atom and the whole system, causing inherently less confined atomic responses and infinitely rugged sub-basins. The implications of these findings for the selective addition or removal of fine structures in the PEL and the subsequent tuning of glassy materials' responses to external stimuli are also explored.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the irreversible sodiation of tin disulfide

Tin disulfide is considered as a promising electrode material for sodium-ion batteries because of its two-dimensional layered structural characteristics allowing the intercalation of Na ions. Understanding the underlying reaction mechanisms and the decisive step of the reaction reversibility is critical for its applications. Herein, we investigate the sodiation and desodiation processes of SnS 2 by employing in situ transmission electron microscopy (TEM). After the initial intercalation reaction, a rock-salt Na y SnS 2 phase with disordering Na and Sn cations is observed, followed with a conversion reaction and an alloying reaction. Additionally, the disordering reaction occurs along <1-10> direction of pristine SnS 2 phase which is correlated with local bonding rearrangements induced by the exchange of Sn and Na cations. In-situ TEM studies and first-principles calculations indicate that the original 2D SnS 2 structure could not be recovered during desodiation. Instead, the disordered Na y SnS 2 phase is finally formed, which indicates that the irreversible disordering transition is the determining step of irreversible cycling. This work probes the structural evolution of sodiation, providing a fundamental understanding of the electrochemical properties of metal sulfides and inspiring rational designs of high performance electrodes for sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Stable all-solid-state sodium-sulfur batteries for low-temperature operation enabled by sodium alloy anode and confined sulfur cathode

All-solid-state sodium-sulfur (Na-S) batteries are promising for stationary energy storage devices because of their low operating temperatures (less than 100 °C), improved safety, and low-cost fabrication. Using Na alloy instead of Na metal as an anode in Na-S batteries can prevent dendrite growth and improve interfacial stability between the anode and solid electrolytes to achieve long-cycling stability. A high-sulfur content cathode possessing high sulfur utilization is also important to enable an energy-dense Na-S battery. In this work, we studied Na-Sb and Na- Sn alloy anodes and demonstrated the superiority of Na 3 Sb alloy undergoing a stable Na alloying/dealloying process at 0.04 mA cm -2 for over 500 hours. Combining the optimized Na3Sb alloy anode with sulfur-carbon composites prepared by the vapor deposition approach, the full cell shows a high sulfur specific capacity and improved rate performance. Moreover, the all-solid-state Na alloy-S battery can deliver a high initial discharge specific capacity of 1377 mAh g -1 and maintain good capacity retention of 70 % after 180 cycles at 60 °C. Further, post-cycle characterizations show that both the anode and cathode perform a reversible discharge/charge process after the 1st cycle, and the cathode undergoes significantly rearranged distributions of carbon and solid-state electrolytes after 180 cycles due to severe volume change induced by repeated sodiation/desodiation process.

25 ENERGY STORAGE↗
DOE OSTI2025

Deciphering volume changes in Li-S solid-state battery components during cycling: Implication for advanced battery design

Here, in this work, we developed custom fixtures to investigate the mechanical and electrochemical behavior of all-solid-state lithium batteries during cycling under constant pressure and constant volume conditions. We successfully monitored vertical displacements during constant pressure cycling and pressure variations during constant volume cycling, allowing us decouple volume changes in the sulfur, Li 2 S cathodes, LixIn anode, and solid-state electrolyte. Scanning electron microscopy and electrochemical impedance spectroscopy confirmed that two structural changes occur during ASSLB cycling: (1) irreversible fractures in the active material particles, and (2) void formation within the electrode matrix. While the fractures in primary particles are permanent, void formation can be mitigated through stack pressure, which promotes particle rearrangement in the electrode matrix. Our findings emphasize the importance of stack pressure in maintaining the microscale integrity of all-solid-state lithium batteries, preventing void formation and enhance battery performance and durability.

Cell Design↗
DOE OSTI2022

Low-synch Gram–Schmidt with delayed reorthogonalization for Krylov solvers

The parallel strong-scaling of iterative methods is often determined by the number of global reductions at each iteration. Low-synch Gram-Schmidt algorithms are applied here to the Arnoldi algorithm to reduce the number of global reductions and therefore to improve the parallel strong-scaling of iterative solvers for nonsymmetric matrices such as the GMRES and the Krylov-Schur iterative methods. In the Arnoldi context, the factorization is "left-looking" and processes one column at a time. Among the methods for generating an orthogonal basis for the Arnoldi algorithm, the classical Gram-Schmidt algorithm, with reorthogonalization (CGS2) requires three global reductions per iteration. A new variant of CGS2 that requires only one reduction per iteration is presented and applied to the Arnoldi algorithm. Delayed CGS2 (DCGS2) employs the minimum number of global reductions per iteration (one) for a one-column at-a-time algorithm. The main idea behind the new algorithm is to group global reductions by rearranging the order of operations. DCGS2 must be carefully integrated into an Arnoldi expansion or a GMRES solver. Numerical stability experiments assess robustness for Krylov-Schur eigenvalue computations. Performance experiments on the ORNL Summit supercomputer then establish the superiority of DCGS2 over CGS2.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Investigating the weak charge of 48 Ca using a dispersive optical model

A new nonlocal dispersive-optical-model analysis has been carried out for neutrons and protons in 48 Ca that reproduces the weak-form-factor measurement of CREX. In addition to elastic-scattering angular distributions, total and reaction cross sections, single-particle energies, the neutron and proton numbers, and the charge distribution, the CREX-measured weak form factor has been fit to extract the neutron and proton self-energies both above and below the Fermi energy. The resulting single-particle propagators yield a weak form factor of F w = 0.125 ± 0.05 and a neutron skin of R skin = 0.152 ± 0.05 fm, in good agreement with CREX. The rearrangement of the neutron distribution to accommodate such a thin neutron skin results in the high-momentum content of the neutrons exceeding that of the protons, in contrast to what is expected from high-energy two-nucleon knockout measurements by the CLAS collaboration and ab initio asymmetric matter calculations. The present analysis also emphasizes the importance of neutron experimental data in constraining weak charge observables necessary for a precise description of neutron densities. Notably, the neutron reaction cross section and further parity-violating experiments weak form factor measurements are essential to generate a unique way to determine the 48 Ca neutron distribution in this framework.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Synthesis of imidazolium-mediated Poly(benzoxazole) Ionene and composites with ionic liquids as advanced gas separation membranes

We report thermally rearranged (TR) polymers and ionic polymers are two material classes which have been employed in leading gas separation membranes. This work introduces a novel approach of combining the benzoxazole functionality associated with TR polymers with tailorable cationic groups, yielding a new type of imidazolium-mediated poly(benzoxazole) ionene polymer, “Im-PBO-Ionene” with the aim of enhanced CO 2 separation performance. The structural changes exhibited from the Coulombic interactions between the ionene backbone and the “free” ionic liquid (IL) resulted in enhanced gas separation performance, shown in fundamental characterizations, observed through increased diffusivities and more notably, retained high selectivities and 3x or 5x respective increases in CO 2 permeability upon the addition of 1 or 2 equivalents of IL per polymer repeat unit. These new high-performance ionenes demonstrate the versatility of ionene design and potential of the ionene + IL material platform for gas separation membranes with versatile incorporation of sophisticated functional and structural features.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Compression behavior of microcrystalline cellulose spheres: Single particle compression and confined bulk compression across regimes

Particle characteristics can drastically influence the process-structure-property-performance aspects of granular materials in compression. In this study, we aim to computationally simulate the mechanical processes of stress redistribution in compacts including the kinematics of particle rearrangement during densification and particle deformation leading to fragmentation. Confined compression experiments are conducted with three sets of commercial microcrystalline cellulose particles nearly spherical in shape with different mean particle size. Experimentally measured compression curves from tall powder columns are fitted with the Kenkre et al. (J. of American Chemical Society, Vol. 79, No. 12) model. This model provides a basis to derive several common two-parameter literature models and as a framework to incorporate statistical representations of critical particle behaviors. We focus on the low-stress compression data and the model comparisons typically not discussed in the literature. Furthermore, additional single particle compressions report fracture strength with particle size for comparison to the apparent particle strength extracted from bulk compression data.

42 ENGINEERING↗
DOE OSTI2026

Defect engineering in nickel via electrodeposition following low temperature annealing

Electrodeposited nickel coatings are characterized by high densities of crystalline defects including dislocations, growth twins, and hydrogen bubbles/voids, arising from the non-equilibrium nature of deposition. While these metastable features influence as-deposited properties, their evolution under low temperature annealing remains unexplored. Here, in this study, we demonstrate that low temperature annealing (200 °C) induces significant microstructural rearrangement without grain growth, enabling defect engineering through thermally assisted dislocation motion and twin boundary migration. Notably, we observe faceted twin boundaries and dislocation organization into extended networks, which have been rarely reported under such annealing conditions. These transformations are attributed to hydrogen-assisted defect mobility, facilitated by the release or redistribution of hydrogen trapped during deposition. These structural transformations correlate with a significant enhancement in mechanical properties, including a twofold increase in yield strength and improved ductility. Our findings highlight the role of trapped hydrogen in mediating low-temperature defect mobility and twin boundary evolution, offering a unique pathway for microstructural tuning of metallic coatings through controlled annealing.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Chromoanagenesis in plants: triggers, mechanisms, and potential impact

Chromoanagenesis is a single catastrophic event that involves, in most cases, localized chromosomal shattering and reorganization, resulting in a dramatically restructured chromosome. First discovered in cancer cells, it has since been observed in various other systems, including plants. In this review, we discuss the origin, characteristics, and potential mechanisms underlying chromoanagenesis in plants. Here, we report that multiple processes, including mutagenesis and genetic engineering, can trigger chromoanagenesis via a variety of mechanisms such as micronucleation, breakage–fusion–bridge (BFB) cycles, or chain-like translocations. The resulting rearranged chromosomes can be preserved during subsequent plant growth, and sometimes inherited to the next generation. Because of their high tolerance to genome restructuring, plants offer a unique system for investigating the evolutionary consequences and potential practical applications of chromoanagenesis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Advancing sustainable aviation fuel with high-energy-density bicycloalkanes production from corn stover mixed sugars

Bicycloalkanes stand out as a replacement for aromatics from conventional jet fuel (CJF) because of their high energy density and lower freezing point. Most reports to date have focused on synthesizing bicycloalkanes using model compounds or single sugar components of lignocellulose. Here, we utilize all lignocellulosic sugars of corn stover (CS) to produce bicycloalkanes. First, furfural (FFR) and 5-hydroxymethyl furfural (5-HMF) are produced via acid-catalyzed dehydration, achieving combined FFRs molar yields ranging from 65% to 73%, respectively. The resulting FFRs are converted to cyclopentanones with molar yields within the range of 57%–63% via hydrogenation and Piancatelli rearrangement. Further aldol condensation of cyclopentanones yields C 10 -C 12 oxygenates with 80 mol %. Lastly, these oxygenates are directly hydrodeoxygenated to bicycloalkanes in a yield of 83.8 mol %. The resulting bicycloalkanes exhibit tier α fuel properties consistent with Jet A fuel (CJF) specifications and blend compatibility with CJF at a 37% volumetric ratio.

09 BIOMASS FUELS↗
DOE OSTI2021

Scavenger receptor MARCO contributes to macrophage phagocytosis and clearance of tumor cells

Highlights: • The MARCO receptor on macrophages was positively correlated with the ability to phagocyte tumor cells. • Macrophage MARCO affects cytoskeleton rearrangement and pseudopodia formation through the SYK-PI3K-Rac1 pathway. • Integrin is the ligand of MARCO on the tumor cells. Macrophage receptor with collagenous structure (MARCO) is a member of the class A scavenger receptor family which is expressed on the cell surface of macrophages. It is well known that MARCO avidly binds to unopsonized pathogens, leading to its ingestion by macrophages. However, the role of MARCO in the recognition and phagocytosis of tumor cells by macrophages remains poorly understood. In this study, we used lentiviral technology to knockdown and overexpress MARCO and investigated the ability of macrophages to phagocytose tumor cells. Our results showed that MARCO expression was correlated with the ability of macrophages to carry on phagocytosis. MARCO knockdown led to significant decreases in the number of engulfment pseudopodia of macrophages and inhibition of the phagocytosis of tumor cells. On the other hand, MARCO overexpression elevated activity of SYK, PI3K and Rac1 in macrophages, which led to changes in macrophage morphology and enhanced phagocytosis by promoting formation of stress fibers and pseudopodia. By Co-IP analysis we showed that MARCO directly binds to the β5 integrin of SL4 tumor cells. In summary, these results demonstrated the important role for MARCO in demonstrated tumor cells uptake and clearance by macrophages.

60 APPLIED LIFE SCIENCES↗