SEARCH · Search NASA

Results for “Reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1980

An active control system for helicopter vibration reduction by higher harmonic pitch

An analytical study defining the basic configuration of an active control system to reduce helicopter vibrations is presented. Theoretical results for a nonlinear four-bladed single rotor helicopter simulation are discussed, showing that vibration reductions on the order of 80-90% for airspeeds up to 150 kn can be expected when using a higher harmonic pitch in an active feedback control system. The rotor performance penalty associated with this level of vibration reduction is about 1-3% and the increase in rotor blade stresses is considered to be low. The location of sensor accelerometers proved to be significant for vibration reductions, and it is noted that the RTSA controller is tolerant of sensor signal noise.

Taylor, R. B.↗

NASA NTRS1981

Forebody drag reduction

It is shown that the mechanisms of forebody drag reduction by means of either a spike or a forward-facing jet are similar, with the maximum achievable drag reduction being of the same order. Because the jet may be a relatively cool gas, however, the forward facing jet has the additional capability of reducing the aerodynamic heating that is so severe at high Mach numbers. By means of the correlation presented, jet ejection parameters may be chosen to achieve maximum permissible forebody drag reduction. The correlation method uses a momentum coefficient that characterizes jet efflux and freestream conditions.

Pamadi, B. N.↗

NASA NTRS1982

Study of noise reduction characteristics of composite fiber-reinforced panels, interior panel configurations, and the application of the tuned damper concept

The application of fiber reinforced composite materials, such as graphite epoxy and Kevlar, for secondary or primary structures developing in the commercial airplane industry was investigated. A composite panel program was initiated to study the effects of some of the parameters that affect noise reduction of these panels. The fiber materials and the ply orientation were chosen to be variables in the test program. It was found that increasing the damping characteristics of a structural panel will reduce the vibration amplitudes at resonant frequencies with attendant reductions in sound reduction. Test results for a dynamic absorber, a tuned damper, are presented and evaluated.

Lameris, J.↗

NASA NTRS1981

Veiling glare reduction methods compared for ophthalmic applications

Veiling glare in ocular viewing was simulated by viewing the retina of an eye model through a sheet of light-scattering material lit from the front. Four methods of glare reduction were compared, namely, optical scanning, polarized light, viewing and illumination paths either coaxial or intersecting at the object, and closed circuit TV. Photographs show the effect of these methods on visibility. Polarized light was required to eliminate light specularly reflected from the instrument optics. The greatest glare reduction was obtained when the first three methods were utilized together. Glare reduction using TV was limited by nonuniform distribution of scattered light over the image.

Buchele, D. R.↗

NASA NTRS1983

A meteorologically-driven yield reduction model for spring and winter wheat

A yield reduction model for spring and winter wheat was developed for large-area crop condition assessment. Reductions are expressed in percentage from a base yield and are calculated on a daily basis. The algorithm contains two integral components: a two-layer soil water budget model and a crop calendar routine. Yield reductions associated with hot, dry winds (Sukhovey) and soil moisture stress are determined. Input variables include evapotranspiration, maximum temperature and precipitation; subsequently crop-stage, available water holding percentage and stress duration are evaluated. No specific base yield is required and may be selected by the user; however, it may be generally characterized as the maximum likely to be produced commercially at a location.

Ravet, F. W.↗

NASA NTRS1983

Conceptual design of a data reduction system

A telemetry data processing system was defined of the Data Reduction. Data reduction activities in support of the developmental flights of the Space Shuttle were used as references against which requirements are assessed in general terms. A conceptual system design believed to offer significant throughput for the anticipated types of data reduction activities is presented. The design identifies the use of a large, intermediate data store as a key element in a complex of high speed, single purpose processors, each of which performs predesignated, repetitive operations on either raw or partially processed data. The recommended approach to implement the design concept is to adopt an established interface standard and rely heavily on mature or promising technologies which are considered main stream of the integrated circuit industry. The design system concept, is believed to be implementable without reliance on exotic devices and/or operational procedures. Numerical methods were employed to examine the feasibility of digital discrimination of FDM composite signals, and of eliminating line frequency noises in data measurements.

Source record↗

NASA NTRS1983

Study of noise reduction characteristics of double-wall panels

The noise reduction characteristics of general aviation type, flat, double-wall structures were investigated. The experimental study was carried out on 20-by-20 inch panels with an exposed area of 18 by 18 inches. A frequency range from 20 to 5000 Hz was covered. The experimental results, in general, follow the expected trends. At low frequencies the double-wall structures are no better than the single-wall structures. However, for depths normally used in the general aviation industry, the double-wall panels are very attractive. The graphite-spoxy skin panels have higher noise reduction at very low frequencies ( 100 Hz) than the Kevlar skin panels. But the aluminum panels have higher noise reduction in the high frequency region, due to their greater mass. Use of fiberglass insulation is not effective in the low frequency region, and at times it is even negative. But the insulation is effective in the high-frequency region. The theoretical model for predicting the transmission loss of these multilayered panels is also discussed.

Navaneethan, R.↗

NASA NTRS1985

Life and reliability modeling of bevel gear reductions

A reliability model is presented for bevel gear reductions with either a single input pinion or dual input pinions of equal size. The dual pinions may or may not have the same power applied for the analysis. The gears may be straddle mounted or supported in a bearing quill. The reliability model is based on the Weibull distribution. The reduction's basic dynamic capacity is defined as the output torque which may be applied for one million output rotations of the bevel gear with a 90 percent probability of reduction survival.

Savage, M.↗

NASA NTRS1985

Method for growth of crystals by pressure reduction of supercritical or subcritical solution

Crystals of high morphological quality are grown by dissolution of a substance to be grown into the crystal in a suitable solvent under high pressure, and by subsequent slow, time-controlled reduction of the pressure of the resulting solution. During the reduction of the pressure interchange of heat between the solution and the environment is minimized by performing the pressure reduction either under isothermal or adiabatic conditions.

Shlichta, P. J.↗

NASA NTRS1985

Anaerobic reduction of elemental sulfur by Chromatium vinosum and Beggiatoa alba

The effect of sulfur globules on the buoyant density of Chromatium vinosum and Beggiatoa alba was examined. The potential use of sulfur as a terminal electron acceptor in the anaerobic metabolism of Beggiatoa alba is also examined. The effect of the reduction of intracellular sulfur was investigated during dark metabolism on the buoyant density of C. vinosum. It is hypothesized from the results that the sulfur reduction to sulfide is part of an anaerobic energy operating system. Carbon stored as PHB can be oxidized with the concomitant reduction of sulfur to sulfide.

Schmidt, T. M.↗

NASA NTRS1985

A fast efficient implicit scheme for the gasdynamic equations using a matrix reduction technique

An efficient implicit finite-difference algorithm for the gasdynamic equations utilizing matrix reduction techniques is presented. A significant reduction in arithmetic operations is achieved without loss of the stability characteristics generality found in the Beam and Warming approximate factorization algorithm. Steady-state solutions to the conservative Euler equations in generalized coordinates are obtained for transonic flows and used to show that the method offers computational advantages over the conventional Beam and Warming scheme. Existing Beam and Warming codes can be retrofit with minimal effort. The theoretical extension of the matrix reduction technique to the full Navier-Stokes equations in Cartesian coordinates is presented in detail. Linear stability, using a Fourier stability analysis, is demonstrated and discussed for the one-dimensional Euler equations.

Barth, T. J.↗

NASA NTRS1986

Combined Devices for Turbulent-Drag Reduction

Aircraft skin-friction drag reduced as much as 15 percent. One effective drag-reduction technique involves use of riblets. Riblets are longitudinal striations or grooves machined on originally smooth surface. Grooves alined with flow. Grooves have depths and spacings on order of turbulent wallstreak and burst dimensions and designed to change near-wall structure of turbulent boundary layer. Another approach, using large-eddy-breakup (LEBU) devices, or turbulence manipulators or ribbons also demonstrated reductions in local skin friction and net drag in air. LEBU device consists of thin, ribbonlike strips or airfoils suspended parallel to test surface and positioned within turbulent boundary layer. Technique potentially reduce net skin-friction drag by at least 15 percent on turbulent boundary layer of aircraft, representing possible annual savings in fuel costs of $300 to $400 million for U.S. commercial fleet. Also applicable to frictionloss reduction inside pipes and ducts, contributing to increased efficiency of pumps, heat exchangers, air conditioners, and other devices involving fluid flow.

Walsh, M. J.↗

NASA NTRS1986

Data reduction, management, and analysis software for CID

In an overview of the Data Reduction System, three major steps are examined. First, the raw data tapes were selected from the onboard recorders. These tapes should provide the best quality data for the data reduction software system. These tapes contained 352 channels of data, plus the monitor channels recorded in 8 bit Pulsed Coded Modulation (PCM) words. The next step consists of transcribing the PCM tapes from 8 bit serial digital data to 8 bit parallel digital data. This puts the data in the correct format for processing. The transcription process was accomplished here at LaRC in the Central Data Transportation Facility (CDTF). The last step in this 3 step process is to process the data through the reduction system developed for the Impact Dynamic Research Facility in the early part of 1980. Processing system criteria, system interface routines, and engineering units program that reads digitized data from tapes, and file management programs are discussed.

Davis, C. W.↗

NASA NTRS1986

Aircraft drag prediction and reduction. Addendum 1: Computational drag analyses and minimization; mission impossible?

The Special Course on Aircraft Drag Prediction was sponsored by the AGARD Fluid Dynamics Panel and the von Karman Institute and presented at the von Karman Institute, Rhode-Saint-Genese, Belgium, on 20 to 23 May 1985 and at the NASA Langley Research Center, Hampton, Virginia, USA, 5 to 6 August 1985. The course began with a general review of drag reduction technology. Then the possibility of reduction of skin friction through control of laminar flow and through modification of the structure of the turbulence in the boundary layer were discussed. Methods for predicting and reducing the drag of external stores, of nacelles, of fuselage protuberances, and of fuselage afterbodies were then presented followed by discussion of transonic drag rise. The prediction of viscous and wave drag by a method matching inviscid flow calculations and boundary layer integral calculations, and the reduction of transonic drag through boundary layer control are also discussed. This volume comprises Paper No. 9 Computational Drag Analyses and Minimization: Mission Impossible, which was not included in AGARD Report 723 (main volume).

Slooff, J. W.↗

NASA NTRS1985

Life and reliability modeling of bevel gear reductions

Savage, M.↗

NASA NTRS1985

Application of modern structural optimization to vibration reduction in rotorcraft

This paper explores a number of techniques which are capable of reducing vibration levels in rotorcraft by redistributing the mass and stiffness properties of the structure. First, vibration reduction in the rotor is considered by using formal structural optimization for ensuring optimal frequency placement. Two cases are considered: in the first case aeroelastic constraints are not enforced and the blade is designed for minimum weight; in the second case aeroelastic constraints are enforced and vibration levels are minimized in forward flight. Next, vibration reduction in the fuselage is considered and the various methods available for vibration reduction by local structural modification are reviewed. The feasibility of combining local structural modification with modern structural optimization is discussed and some extensions of previous research are suggested.

Friedmann, P.↗

NASA NTRS1985

Mixed models and reduction method for dynamic analysis of anisotropic shells

A time-domain computational procedure is presented for predicting the dynamic response of laminated anisotropic shells. The two key elements of the procedure are: (1) use of mixed finite element models having independent interpolation (shape) functions for stress resultants and generalized displacements for the spatial discretization of the shell, with the stress resultants allowed to be discontinuous at interelement boundaries; and (2) use of a dynamic reduction method, with the global approximation vectors consisting of the static solution and an orthogonal set of Lanczos vectors. The dynamic reduction is accomplished by means of successive application of the finite element method and the classical Rayleigh-Ritz technique. The finite element method is first used to generate the global approximation vectors. Then the Rayleigh-Ritz technique is used to generate a reduced system of ordinary differential equations in the amplitudes of these modes. The temporal integration of the reduced differential equations is performed by using an explicit half-station central difference scheme (Leap-frog method). The effectiveness of the proposed procedure is demonstrated by means of a numerical example and its advantages over reduction methods used with the displacement formulation are discussed.

Noor, A. K.↗

NASA NTRS1986

Experimental investigation of rotorcraft hub and shaft fairing drag reduction

A wind-tunnel test was conducted to obtain data on several rotorcraft hub and shaft fairing drag reduction configurations. Aerodynamic loads and moments were acquired for each test configuration. Limited wake pressure measurements and flow visualization (tuft) photographs were obtained for some configurations. All hub and shaft fairing configurations were tested on a 1/5-scale XH-59A model fuselage. Both coaxial and single rotor configurations were tested. All rotor assemblies were modeled with nonrotating hardware. The drag reduction methods tested included cambered elliptical hub fairings, several different shaft fairings, and strakes. Test data show that significant drag reductions can be attained with certain fairing configurations. The lowest drag values for the single rotor configurations were obtained for a cambered elliptical hub fairing with a large thickness airfoil shaft fairing. The lowest coaxial configuration drag values were obtained with cambered elliptical hub fairings and a long chord intermediate shaft fairing.

Young, L. A.↗