Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLIDING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Tunable amorphous carbon films formed on ultralow wear, Pt–Au alloys

The mechanocatalytic formation of carbonaceous films at the interface between sliding metallic contacts is simultaneously advantageous for reducing friction and adhesion in several tribological applications and detrimental for electrical contacts as they can induce device failure by increasing the contact resistance. Yet, remarkably little is still known about the chemistry, structural and mechanical properties, and tunability of these interfacial layers. In this study, we performed contact pressure-dependent tribological experiments in dry nitrogen containing trace organics on four, nanocrystalline Pt–Au alloys ([Au] from 0 at.% to 10 at.%) – a promising class of alloys for ultralow wear and electrical contact applications. The ex-situ, multi-technique characterization results did not only provide insights into the chemical nature and mechanical behavior of the mechanocatalytic, carbon-rich films formed on Pt–Au surfaces, but also revealed the interplay between catalytic and mechanochemical tribofilm formation controlled by the composition-dependent electronic structure of the Pt–Au substrate and the applied contact pressure. The results of this work provide guidelines for tailoring nanocrystalline alloys to control their mechanocatalytic activity on the basis of variations of the alloy mechanical properties and element's electronic structure with the alloy stoichiometry.

AFM↗
DOE OSTI2026

Designing Thermomechanically Stable Nanocrystalline Alloys for Low Friction and Wear: A Perspective

In this Perspective, we discuss recent work and future trends on the usage of thermomechanically stable and selflubricating nanocrystalline (NC) alloys for low friction and wear applications. The theoretical underpinnings and mechanistic framework for attaining and maintaining low friction and wear in metal contacts are presented. Initial work on stress, time, and temperature-dependent changes in friction and wear in NC alloys validates the models, demonstrating lower friction from decreased interfacial strength, contact pressure, sliding speed, and temperature and increased roughness and material hardness. Subsequent work reveals that NC Pt−Au, metal nitrides, complex-concentrated, and high-entropy alloys come with additional stabilization factors such as low-friction carbon tribofilms and oxide/amorphous−crystalline layers but are still susceptible to destabilization factors including irradiation and adverse environmental conditions.

alloys↗
DOE OSTI2025

Tribology and Tribocorrosion of Case-Hardened Steels: A Review

This report reviews the tribological and tribocorrosion performance of steels that are case-hardened via boriding, chromizing, carburizing, nitriding, nitrocarburizing, and carbonitriding. Case-hardening is commonly used to improve the hardness, impact durability, wear resistance, and corrosion resistance of steel alloys and has been successfully applied in various industries, providing a cost-effective, high-throughput solution for applications involving contact and sliding interfaces in complex service environments. This article summarizes the literature results of the wear and friction behavior of common case-hardening methods for steel alloys under various conditions, including corrosive environments. Special attention is given to the influences of case-hardening process parameters and alloy composition on tribological performance. Furthermore, by discussing key findings from the literature, this review provides insights into optimizing case-hardening processes for improving the tribological and tribocorrosion performance of steel alloys.

Alloys↗
NASA NTRS1967

Solenoid valve design has one moving part

Solenoid valve structure has only one moving part, a ball and spring assembly. This eliminates wear caused by sliding motion contact between stationary and moving parts or between moving parts.

Anderson, J. W.↗
NASA NTRS1974

High shear stress behavior of some representative lubricants

Shear stress independent behavior observed for representative, synthetic, nonblended lubricants is found to be of the same magnitude as the shear stress in sliding elastohydrodynamic contacts. It is shown that dissipation heating is the only mechanism of importance in the generation of deviations from constant viscosity as measured with capillary tube viscometric methods. Newtonian end corrections for capillary tubes are found to be constant for nonblended liquid lubricants.

Jakobsen, J.↗
NASA NTRS1978

Ferrographic analysis of wear particles from sliding elastohydrodynamic experiments

The Ferrograph was used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness (A ratio). The general wear level parameter and the wear severity index yielded similar correlations with average A ratios. Essentially all the generated wear particles were of the normal rubbing wear type. The Ferrograph was more sensitive in detecting the wear debris than was the commonly used emission spectrograph.

Jones, W. R., Jr.↗
NASA NTRS1983

Traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed.

Loewenthal, S. H.↗
NASA NTRS1984

Elastic model of the traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

Loewenthal, S. H.↗
NASA NTRS1951

Preliminary Investigation of Molybdenum Disulfide-air-mist Lubrication for Roller Bearings Operating to DN Values of 1 x 10(exp 6) and Ball Bearings Operating to Temperatures of 1000 F

The effectiveness of molybdenum disulfide MoS2 as a bearing lubricant was determined at high temperature and at high speeds. A 1-inch-bore ball bearing operated at temperatures to 1000 F, a speed of 1725 rpm, and a thrust load of 20 pounds when lubricated only with MoS2-air mist. A 75-millimeter-bore cageless roller bearing, provided with a MoS2-syrup coating before operation, operated at DN values to 1 x 10(exp 6) with a load of 368 pounds.

BEARINGS, ANTI - FRICTION↗
NASA NTRS1951

Comparison of High-Speed Operating Characteristics of Size 215 Cylindrical-Roller Bearings as Determined in Turbojet Engine and in Laboratory Test Rig

A comparison of the operating characteristics of 75-millimeter-bore (size 215) cylindrical-roller one-piece inner-race-riding cage-type bearings was made using a laboratory test rig and a turbojet engine. Cooling correlation parameters were determined by means of dimensional analysis, and the generalized results for both the inner- and outer-race bearing operating temperatures are compared for the laboratory test rig and the turbojet engine. Inner- and outer-race cooling-correlation curves were obtained for the turbojet-engine turbine-roller bearing with the same inner- and outer-race correlation parameters and exponents as those determined for the laboratory test-rig bearing. The inner- and outer-race turbine roller-bearing temperatures may be predicted from a single curve, regardless of variations in speed, load, oil flow, oil inlet temperature, oil inlet viscosity, oil-jet diameter or any combination of these parameters. The turbojet-engine turbine-roller-bearing inner-race temperatures were 30 to 60 F greater than the outer-race-maximum temperatures, the exact values depending on the operating condition and oil viscosity; these results are in contrast to the laboratory test-rig results where the inner-race temperatures were less than the outer-race-maximum temperatures. The turbojet-engine turbine-roller bearing, maximum outer-race circumferential temperature variation was approximately 30 F for each of the oils used. The effect of oil viscosity on inner- and outer-race turbojet-engine turbine-roller-bearing temperatures was found to be significant. With the lower viscosity oil (6x10(exp -7) reyns (4.9 centistokes) at 100 F; viscosity index, 83), the inner-race temperature was approximately 30 to 35 F less than with the higher viscosity oil (53x10(exp -7) reyns (42.8 centistokes) at 100 F; viscosity index, 150); whereas the outer-race-maximum temperatures were 12 to 28 F lower with the lower viscosity oil over the DN range investigated.

BEARINGS, ANTI-FRICTION↗
NASA NTRS1998

"Long life" DC brush motor for use on the Mars surveyor program

DC brush motors have several qualities which make them very attractive for space flight applications. Their mechanical commutation is simple and lightweight, requiring no external sensing and control in order to function properly. They are extremely efficient in converting electrical energy into mechanical energy. Efficiencies over 80% are not uncommon, resulting in high power throughput to weight ratios. However, the inherent unreliability and short life of sliding electrical contacts, especially in vacuum, have driven previous programs to utilize complex brushless DC or the less efficient stepper motors. The Mars Surveyor Program (MSP'98) and the Shuttle Radar Topography Mission (SRTM) have developed a reliable "long life" brush type DC motor for operation in low temperature, low pressure CO2 and N2, utilizing silver-graphite brushes. The original intent was to utilize this same motor for SRTM's space operation, but the results thus far have been unsatisfactory in vacuum. This paper describes the design, test, and results of this development.

Braun, David↗
NASA NTRS1981

Dynamics of solid dispersions in oil during the lubrication of point contacts. Part 1: Graphite

A Hertzian contact was lubricated with dispersed graphite in mineral oils under boundary lubrication conditions. The contact was optically observed under pure rolling, combined rolling and sliding, and pure sliding conditions. The contact was formed with a steel ball on the flat surface of a glass disk. Photomicrographs are presented which show the distribution of the graphite in and around the contact. Friction and surface damage are also shown for conditions when the base oils are used alone and when graphite is added to the base oils. Under pure rolling and combined rolling and sliding conditions, it is found that, for low speeds, a graphite film can form which will separate the contacting surfaces. Under pure sliding conditions, graphite accumulates at the inlet and sweeps around the contact, but very little of the graphite passes through the contact. The accumulated graphite appears to act as a barrier which reduces the supply of oil available to the contact for boundary lubrication. Friction data show no clear short term beneficial or detrimental effect caused by addition of graphite to the base oil. However, during pure sliding, more abrasion occurs on the polished balls lubricated with the dispersion than on those lubricated with the base oil alone. All observations were for the special case of a highly-polished ball on a glass surface and may not be applicable to other geometries and materials, or to rougher surfaces.

Cusano, C.↗
NASA NTRS1981

Dynamics of solid dispersions in oil during the lubrication of point contacts. I - Graphite

A Hertzian contact is lubricated with dispersed graphite in mineral oils under boundary lubrication conditions. The contacts are optically observed under pure rolling, combined rolling and sliding, and pure sliding conditions. The contact is formed with a steel ball on the flat surface of a glass disk. Under pure rolling and combined rolling and sliding conditions, it is found that, for low speeds, a graphite film can form which will separate the contacting surfaces. In contrast, under pure sliding conditions, graphite accumulates at the inlet and sweeps around the contact, but very little of graphite passes through the contact. The accumulated graphite appears to act as a barrier which reduces the supply of oil available to the contact for boundary lubrication. Friction data show no clear short-term beneficial or detrimental effect caused by addition of graphite to the base oil. However, during pure sliding, more abrasion occurs on the polished balls lubricated with the dispersion than on those lubricated with the base oil alone.

Cusano, C.↗
NASA NTRS1984

Efficiency of nonstandard and high contact ratio involute spur gears

A power loss prediction was extended to include involute spur gears of nonstandard proportions. The method is used to analyze the effects of modified addendum, tooth thickness, and gear center distance in addition to the parameters previously considered which included gear diameter, pitch, pressure angle, face width, oil viscosity, speed, and torque. Particular emphasis was placed on high contact ratio gearing (contact ratios greater than two). Despite their higher sliding velocities, high contact ratio gears are designed to levels of efficiency comparable to those of conventional gears while retaining their advantages through proper selection of gear geometry.

Anderson, N. E.↗
NASA NTRS1986

Efficiency of nonstandard and high contact ratio involute spur gears

A power loss prediction was extended to include involute spur gears of nonstandard proportions. The method is used to analyze the effects of modified addendum, tooth thickness, and gear center distance in addition to the parameters previously considered which included gear diameter, pitch, pressure angle, face width, oil viscosity, speed, and torque. Particular emphasis was placed on high contact ratio gearing (contact ratios greater than two). Despite their higher sliding velocities, high contact ratio gears are designed to levels of efficiency comparable to those of conventional gears while retaining their advantages through proper selection of gear geometry.

Anderson, N. E.↗
NASA NTRS1975

Wear and interfacial transport of material

The paper is a review of adhesion or bonding across an interface between two solids in contact, transfer or transport to one or both surfaces, wear with tangential motion, and the effect of surface films on adhesion, transfer, and wear. The discussion is limited to the case of adhesive wear which deals with the interfacial transport of material from one surface to another. The data presented suggest that the resulting interfacial adhesive bond for metals in contact is generally stronger than the cohesive bond in the cohesively weaker of the two materials so that upon separation of the surfaces transfer will occur from the cohesively weaker material to the cohesively stronger; that with tangential motion of two metal surfaces in contact such as encountered with sliding, rolling, or rubbing contact, the frictional energy can be dissipated in a number of ways, where heating of the surfaces can produce metallurgical changes such as alloying; and that the presence of adsorbed and reacted films on the surface of metals and alloys even in frictions of a monolayer can reduce interfacial bonding, adhesion, and transfer.

Buckley, D. H.↗
NASA NTRS1980

Finite elements for contact problems in two-dimensional elastodynamics

A finite element approach for contact problems in two dimensional elastodynamics was proposed. Sticking, sliding, and frictional contact were taken into account. The method consisted of a modification of the shape functions, in the contact region, in order to involve the nodes of the contacting body. The formulation was symmetric (both bodies were contactors and targets), in order to avoid interpenetration. Compatibility over the interfaces was satisfied. The method was applied to the impact of a block on a rigid target. It is shown that the formulation can be applied to fluid structure interaction, and to problems involving material nonlinearity.

Zimmermann, T. K.↗