Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLOTTED WIND TUNNEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Experimental study of flow due to an isolated suction hole and a partially plugged suction slot

Details for construction of a model of a partially plugged, laminar flow control, suction slot and an isolated hole are presented. The experimental wind tunnel facility and instrumentation is described. Preliminary boundary layer velocity profiles (without suction model) are presented and shown to be in good agreement with the Blasius laminar profile. Recommendations for the completion of the study are made. An experimental program for study of transition on a rotating disk is described along with preliminary disturbance amplification rate data.

Goglia, G. L.↗
NASA NTRS1980

Large-scale wind-tunnel tests of inverting flaps on a STOL utility aircraft model

A unique inverting flap system was investigated on a large scale deflected slipstream model in the Ames 40 by 80 foot wind tunnel. The subject tests utilized 33% chord double-slotted flaps on a low aspect ratio wing that was fully immersed in the propeller slipstream. Evaluation of the flap effectiveness is aided by comparisons with the results of tests of other flap systems on the same twin propeller, twin tail boom STOL utility aircraft mode. No extreme or abrupt force or moment increments were encountered when the flaps were deflected through a wide range, corresponding to the complete retraction/extension spectrum. The lift and descent capability of the inverting flaps compared very favorably with that of the other flap systems that have been tested on this model, including some with much greater mechanical complexity. As expected, the flaps caused large nose down, pitching moment increments at the high lift settings; however, the trimmed characteristics are still competitive with those obtained from the more complicated flap systems. It is believed that these flaps may have promising potential application to the design of relatively simple STOL utility aircraft with improved performance capabilities. In addition, they may merit consideration as retrofits to existing aircraft with less effective flap systems.

Feistel, T. W.↗
NASA NTRS1995

Computational Investigation of Tangential Slot Blowing on a Generic Chined Forebody

The effect of tangential slot blowing on the flowfield about a generic chined forebody at high angles of attack is investigated numerically using solutions of the thin-layer, Reynolds-averaged, Navier-Stokes equations. The effects of jet mass now ratios, angle of attack, and blowing slot location in the axial and circumferential directions are studied. The computed results compare well with available wind-tunnel experimental data. Computational results show that for a given mass now rate, the yawing moments generated by slot blowing increase as the body angle of attack increases. It is observed that greater changes in the yawing moments are produced by a slot located closest to the lip of the nose. Also, computational solutions show that inboard blowing across the top surface is more effective at generating yawing moments than blowing outboard from the bottom surface.

Agosta-Greenman, Roxana M.↗
NASA NTRS2016

Computations of Combustion-Powered Actuation for Dynamic Stall Suppression

A computational framework for the simulation of dynamic stall suppression with combustion-powered actuation (COMPACT) is validated against wind tunnel experimental results on a VR-12 airfoil. COMPACT slots are located at 10% chord from the leading edge of the airfoil and directed tangentially along the suction-side surface. Helicopter rotor-relevant flow conditions are used in the study. A computationally efficient two-dimensional approach, based on unsteady Reynolds-averaged Navier-Stokes (RANS), is compared in detail against the baseline and the modified airfoil with COMPACT, using aerodynamic forces, pressure profiles, and flow-field data. The two-dimensional RANS approach predicts baseline static and dynamic stall very well. Most of the differences between the computational and experimental results are within two standard deviations of the experimental data. The current framework demonstrates an ability to predict COMPACT efficacy across the experimental dataset. Enhanced aerodynamic lift on the downstroke of the pitching cycle due to COMPACT is well predicted, and the cycleaveraged lift enhancement computed is within 3% of the test data. Differences with experimental data are discussed with a focus on three-dimensional features not included in the simulations and the limited computational model for COMPACT.

Jee, Solkeun↗
NASA NTRS1942

Pressure distribution over an NACA 23012 airfoil with a fixed slot and a slotted flap

Report presents the results of a pressure-distribution investigation conducted in the Langley Memorial Aeronautical Laboratory 7 by 10-foot wind tunnel to determine the air loads on an NACA 23012 airfoil in combination with a fixed leading-edge slot and a slotted flap. Pressures were measured over the upper and lower surfaces of the component parts of the combination for several angles of attack and at several flap settings. The data, presented as pressure diagrams and graphs of section coefficients, are applicable to rib, slat, and flap designs for the combination.

Harris, Thomas A↗
NASA NTRS2004

Parametric Studies of Flow Separation using Air Injection

Boundary Layer separation causes the airfoil to stall and therefore imposes dramatic performance degradation on the airfoil. In recent years, flow separation control has been one of the active research areas in the field of aerodynamics due to its promising performance improvements on the lifting device. These active flow separation control techniques include steady and unsteady air injection as well as suction on the airfoil surface etc. This paper will be focusing on the steady and unsteady air injection on the airfoil. Although wind tunnel experiments revealed that the performance improvements on the airfoil using injection techniques, the details of how the key variables such as air injection slot geometry and air injection angle etc impact the effectiveness of flow separation control via air injection has not been studied. A parametric study of both steady and unsteady air injection active flow control will be the main objective for this summer. For steady injection, the key variables include the slot geometry, orientation, spacing, air injection velocity as well as the injection angle. For unsteady injection, the injection frequency will also be investigated. Key metrics such as lift coefficient, drag coefficient, total pressure loss and total injection mass will be used to measure the effectiveness of the control technique. A design of experiments using the Box-Behnken Design is set up in order to determine how each of the variables affects each of the key metrics. Design of experiment is used so that the number of experimental runs will be at minimum and still be able to predict which variables are the key contributors to the responses. The experiments will then be conducted in the 1ft by 1ft wind tunnel according to the design of experiment settings. The data obtained from the experiments will be imported into JMP, statistical software, to generate sets of response surface equations which represent the statistical empirical model for each of the metrics as a function of the key variables. Next, the variables such as the slot geometry can be optimized using the build-in optimizer within JMP. Finally, a wind tunnel testing will be conducted using the optimized slot geometry and other key variables to verify the empirical statistical model. The long term goal for this effort is to assess the impacts of active flow control using air injection at system level as one of the task plan included in the NASAs URETI program with Georgia Institute of Technology.

Zhang, Wei↗
NASA NTRS1947

Investigation of a Spoiler-Type Lateral Control System on a Wing with Full-Span Flaps in the Langley 19-Foot Pressure Tunnel

Tests of a partial-span model of a large bomber-type air1ane were conducted to determine the. aerodynamic characteristics of the wing equipped with full-span flaps and a retractable spoiler end aileron lateral control system. The arrangement consisted of (1) a double slotted flap extending over aproximate1y 86 percent of the wing semispan, (2) a 20-percent constant-percentage-chord aileron extending from the outboard end of the flap to the wing tip, and (3) a retractable spoiler, located at the 65-percent wing-chord station and extending from approximately 63 percent of the wing semispan to the wing tip. In addition, tests were made of a wing vent (of 1 and 2 percent of the wing chord located directly behind the spoiler), perforations in the spoiler, a blot or cut-out along the lower edge of the spoiler and spoilers of various spans. With full-span flaps deflected and with the 2-percent vent open or closed the initial stalling of the wing occurred at the tips, but with the vents closed there probably would be no appreciable loss in lateral control until maximum lift was reached. The l-percent vent increased the rolling effectiveness of the spoiler at small spoi1er deflections, particularly at high angles of attack with flaps deflected. With flaps deflected the 2-percent vent caused a large reduction in both the wing lift and rolling effectiveness of the spoiler at large angles of attack. However, at small angle of attack the 2-percent vent increased the rolling effectiveness of the spoiler at small spoiler deflections. The simultaneous operation of the spoiler and vent (in contrast to a vent fixed in the wing) would result in a large increase in the effectiveness of the spoiler and would avoid any loss in wing lift as in a fixed vent arrangement. The tests of the spoiler modifications revealed that (1) the spoiler perforations reduced the rolling-moment and yawing-moment coefficients but caused the spoiler hinge-moment coefficients to become more positive; (2) the spoiler slot had no notable effect on the rolling-moment and yawing-moment characteristics but produced a positive increase in the spoiler hinge-moment coefficients at large spoiler deflections; (3) the effects produced by the individual modifications were additive when the various modifications were combined. In general, progressively decreasing the spoiler span by removing the segments from the inboard end of the spoiler caused a decrease in rolling effectiveness approximately proportional to the span of the segment.

WING FLAPS, SLOTTED & AILERONS↗
NASA NTRSDate not supplied

Aeroelastic Simulation of Wind Tunnel Scale Aspect Ratio 13.5 Common Research Model with Trailing Edge Mini-Flaps

This paper presents a computation study of an aspect ratio 13.5 wind tunnel scale Common Research Model (CRM) with trailing edge mini-flaps using FUN3D. The aeroelastic simulations are conducted under free-air and inside wind tunnel conditions. The NASA Langley Research Center Transonic Dynamic Tunnel (TDT) is a closed circuit and slotted-test-section with a 16 ft ×16 ft test section. The structure mode shapes are extracted from the latest updated NASTRAN Finite-Element Model (FEM) model. A dynamic pressure sweep is performed to determine the control reversal boundary of the trailing edge mini-flaps. The wind tunnel wall interference effects on the mini-flap control derivatives are analyzed based on the simulations.

Aeroelastic↗
NASA NTRS1998

Overview of Laminar Flow Control

The history of Laminar Flow Control (LFC) from the 1930s through the 1990s is reviewed and the current status of the technology is assessed. Early studies related to the natural laminar boundary-layer flow physics, manufacturing tolerances for laminar flow, and insect-contamination avoidance are discussed. Although most of this publication is about slot-, porous-, and perforated-suction LFC concept studies in wind tunnel and flight experiments, some mention is made of thermal LFC. Theoretical and computational tools to describe the LFC aerodynamics are included for completeness.

Joslin, Ronald D.↗
NASA NTRS2004

Flutter Stability of the Efficient Low Noise Fan Calculated

The TURBO-AE aeroelastic code has been used to verify the flutter stability of the Efficient Low Noise Fan (ELNF), which is also referred to as the trailing-edge blowing fan. The ELNF is a unique technology demonstrator being designed and fabricated at the NASA Glenn Research Center for testing in Glenn's 9-by-15-Foot Low-Speed Wind Tunnel. In the ELNF, air can be blown out of slots near the trailing edges of the fan blades to fill in the wakes downstream of the rotating blades. This filling of the wakes leads to a reduction of the rotor-stator interaction (tone) noise that results from the interaction of wakes with the downstream stators. The ELNF will demonstrate a 1.6-EPNdB1 reduction in tone noise through wake filling, without increasing the broadband noise. Furthermore, the reduced blade row interaction will decrease the possibility of forced response and enable closer spacing of blade rows, thus reducing engine length and weight. During the design of the ELNF, the rotor blades were checked for flutter stability using the detailed aeroelastic analysis capability of the three-dimensional Navier-Stokes TURBOAE code. The aeroelastic calculations were preceded by steady calculations in which the blades were not allowed to vibrate. For each rotational speed, as the back-pressure was increased, the mass flow rate decreased, and the operating point moved along the constant speed characteristic (speed-line) from choke to stall as shown on the fan map. The TURBO-AE aeroelastic analyses were performed separately for the first two vibration modes (bending and torsion) and covered the complete range of interblade phase angles or nodal diameters at which flutter can occur. The results indicated that the ELNF blades would not encounter flutter at takeoff conditions. The calculations were then repeated for a part-speed condition (70-percent rotational speed), and the results again showed no flutter in the operating region. On the fan map (shown), the predicted flutter point at part speed condition was located beyond the stall line, which means that the ELNF will not encounter flutter since it will never operate beyond the stall line. All the calculations done so far have been for the nonblowing case, and selected calculations will be repeated with air blowing from the trailing edge of the fan.

Bakhle, Milind A.↗
NASA NTRS1933

The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight

This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.

WING SLOTS↗
NASA NTRS1989

Experimental investigation of the high angle of attack characteristics of a high performance general aviation aircraft

Scale model wind tunnel tests and full scale flight tests have been conducted for the Questair Venture general aviation aircraft configuration in order to investigate its high angle-of-attack aerodynamics. Attention is given to the formulation of a wing leading-edge modification capable of enhancing stall departure characteristics. This modification, which involved both outboard wing leading-edge droop and two chordwise leading-edge slots, is found to produce almost no wing-rock tendency when tested on a wind tunnel free-to-roll apparatus; in the full-scale aircraft, the modification yielded gentle, controllable stall characteristics with little cruise and climb performance penalty.

Meyer, H. F.↗
NASA NTRS1974

Noise reduction in transonic wind tunnels

The phenomena of background noise generation in transonic wind tunnels are analyzed. In unsteady aerodynamic tests, background disturbances create problems because the instrumentation senses them in addition to the fluctuations generated by the aerodynamic flow over wind-tunnel models. Calibrations of 25 facilities show that the amplitudes of the background fluctuations are excessive. In porous-wall facilities, one noise source consists of porous-wall edgetones that are generated by the passage of air over the holes. A flow model is developed that yields the frequencies of these oscillations. Test section boundary layers and hole configurations govern the occurrence of these fluctuations. In slotted-wall facilities, a noise source is the slotted-wall shearing caused by the air flowing along the openings. In both types of wind tunnels, other flow mechanisms also cause disturbances, and these phenomena are described. Noise-reduction methods are outlined which will provide valid unsteady aerodynamic results.

Mccanless, G. F., Jr.↗