Data for "Arsenic Activation and Compensation in Single Crystal CdTe Bilayers"
Explore the source record for details and available documents.
14 SOLAR ENERGY↗
SEARCH · Search NASA
Results for “SOLAR ACTIVITY”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Improving photovoltaic hosting capacity of distribution networks with coordinated inverter control: A case study of the EPRI J1 feeder
Abstract Adding photovoltaic (PV) systems in distribution networks, while desirable for reducing the carbon footprint, can lead to voltage violations under high solar‐low load conditions. The inability of traditional volt‐VAr control in eliminating all the violations is also well‐known. This article presents a novel coordinated inverter control methodology that leverages system‐wide situational awareness to significantly improve hosting capacity (HC). The methodology employs a real‐time voltage‐reactive power (VQ) sensitivity matrix in an iterative linear optimizer to calculate the minimum reactive power intervention from PV inverters needed for mitigating over‐voltage without resorting to active power curtailing or requiring step voltage regulator setting changes. The algorithm is validated using the EPRI J1 feeder under an extensive set of realistic use cases and is shown to provide 3x improvement in HC under all scenarios.
Dalal, Dhaval [School of Electrical, Computer, and↗
A review on protection challenges of Transmission Lines connected to Inverter Based Resources
The increased penetration of inverter-based resources (IBRs) connected to transmission grids is challenging how traditional electric power systems operate. Such systems were originally designed based on the dominant presence of synchronous generators. Some main challenges include the increased concerns about system stability due to the reduced system inertia caused by IBRs and the reduced protection reliability caused by the non-deterministic fault current response of IBRs. The protection relays’ algorithms have been designed and validated based on well-known fault current characteristics of synchronous generations, while the short-circuit responses of IBRs heavily depend on their vendor-specific control schemes, which are mainly set to protect inverter semiconductor switches and DC components. The magnitude of short current that IBRs contribute is typically between 1.1–1.5 times the rated current that may behave unstably and incoherently with the voltages. The control scheme of the IBRs also controls the active (P) and reactive (Q) support during system voltage sag and swell conditions. These characteristics challenge not only protective relay schemes but also existing short-circuit software tools to correctly model IBRs for fault studies and protection coordination analyses.
14 SOLAR ENERGY↗
Science Driven Discovery of Nanoparticle Photocatalysts
Photocatalytic water splitting using suspensions of nanoparticle photocatalysts is a promising route to economically sustainable production of green hydrogen. The principal challenge is to develop photocatalysts with overall solar-to-hydrogen conversion efficiency that exceeds 10 percent. In this project we have developed a new platform for investigating candidate materials for photocatalytic water splitting. Our platform consists of patterned Au electrodes and a Ag/AgCl reference electrode on an insulating substrate onto which we disperse nanoparticle photocatalysts. We then cover the substrate with a thin layer of ionogel containing a protic ionic liquid that dissolves water from the ambient. Using this platform we have demonstrated photoelectrochemical activity mapping for single and small clusters of BiVO 4 nanoparticle photocatalysts and correlated these results to their Raman and photoluminescence spectra. The preliminary results suggest a strong correlation for low efficiency nanoparticles, followed by saturation for those with higher activities, indicating that interface reaction or electrolyte transport become the limiting factor. We anticipate that further application of this platform to investigation of candidate photocatalyst materials will provide useful insights into the mechanisms that limit their performance.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Machine learning enhanced characterization and optimization of photonic cured MAPbI 3 for efficient perovskite solar cells
Photonic curing (PC) can facilitate high-speed perovskite solar cell (PSC) manufacturing because it uses high-intensity light pulses to crystallize perovskite films in milliseconds. However, optimizing PC conditions is challenging due to its many variables, and using power conversion efficiency (PCE) as the optimization metric is both time-consuming and labor-intensive. This work presents a machine learning (ML) approach to optimize PC conditions for fabricating methylammonium lead iodide (MAPbI 3 ) films by quantitatively comparing their ultraviolet-visible (UV-vis) absorbance spectra to thermal annealed (TA) films using four similarity metrics. We perform Bayesian optimization coupled with Gaussian process regression (BO-GP) to minimize the similarity metrics. Refining PC conditions using active learning based on BO-GP models, we achieve a PC MAPbI3 film with an absorbance spectrum closely matching a TA reference film, which is further verified by its crystalline and morphological properties. Thus, we demonstrate that the UV-vis absorption spectrum can accurately proxy film quality. Additionally, we use an AI-based segmentation model for a more efficient grain size analysis. However, when we use the optimized PC condition to fabricate PSCs, we find that interaction between MAPbI 3 and the hole transport layer (HTL) during PC critically degrades the PSC performance. By adding a buffer layer between the HTL and MAPbI 3 , the optimized PC PSCs produce a champion PCE of 11.8%, comparable to the TA reference of 11.7%. Using UV-vis similarity metrics instead of device PCE as the objective in our BO-GP method accelerates the optimization of PC processing conditions for MAPbI 3 films.
14 SOLAR ENERGY↗
Ammonolysis with N 2 -diluted NH 3 suppresses Ta( IV ) defects in BaTaO 2 N and enhances photocatalytic water oxidation
BaTaO 2 N stands out among oxynitride photocatalysts because of its ability to capture visible light and to drive the photoelectrochemical water oxidation reaction. However, its solar energy conversion performance is limited by electron–hole recombination at Ta( IV ) defects in the material. These defects are formed by overreduction of the Ta(v) oxide precursor by excess ammonia under the high temperature conditions during ammonolysis. Here we show for the first time that Ta( IV ) defect concentrations can be lowered by conducting the ammonolysis reaction in mixed NH 3 /N 2 gas. The obtained BaTaO 2 N samples crystallize in the cubic CaTiO 3 structure type and form 200–300 nm faceted nanocrystals, based on X-ray diffraction, scanning electron microscopy, and HRTEM. Electron paramagnetic resonance spectra observe the Ta( IV ) defects at g = 1.999 and confirm an 11-fold reduction for the product synthesized in mixed (0.13 : 1.0 vol) NH 3 /N 2 gas, equivalent to 1.14 × 10 16 cm −3 Ta( IV ) ions. This optimized BaTaO 2 N has nearly twice the photocatalytic oxygen evolution activity (AQE of 6.78% at 400 nm) of a reference material made with 1.0 atm ammonia and 78% higher photoelectrochemical water oxidation photocurrent (0.9 mA cm −2 at 1.23 V vs. RHE) under simulated sunlight. According to X-ray photoelectron spectroscopy, remaining Ta( IV ) defects are concentrated in the surface region of the BaTaO 2 N particles, where >50% of all Ta ions are found in the +4 oxidation state. This surface Ta( IV ) population can be directly observed in Vibrating Kelvin Probe Surface Photovoltage Spectra (VK-SPV) via its 1.2–1.4 eV photovoltage onset. Here, it suggests that the surface Ta( IV ) ions contribute empty d-states 0.5–0.7 eV below the BaTaO 2 N conduction band edge. These findings highlight how the energetics and concentrations of Ta( IV ) defects influence the photoelectrochemical water oxidation ability of BaTaO 2 N. Additionally, the work establishes ammonolysis with diluted NH 3 as a new tool to minimize defects in BaTaO 2 N and to raise its solar energy conversion efficiency toward its theoretical limit. Because of its simplicity, the reduced ammonia pressure strategy will likely be applicable to other oxynitrides, which generally suffer from overreduction problems during ammonolysis.
Salmanion, Mahya [University of California, Davis,↗
Leveraging Existing Assets for Long Duration Energy Storage
Increased renewables penetration to electrical grid is necessary to reduce overall emissions from the electrical power generation sector. Nonetheless, its integration creates challenges to grid operators who must match the power being generated by intermittent renewables and other traditional energy sources with the demand from consumers, while ensuring the reliability and power quality for the entire system. Energy storage has been proposed as an alternative to natural gas peaking plants and a form to deliver excess renewable energy generation at times of peak demand. For energy storage to provide benefits to end customers (energy consumers), it must be reliable, efficient, and cost effective. The Illinois Sustainable Technology Center (ISTC), one of the surveys that integrate the Prairie Research Institute (PRI), aims to develop a Center for Energy Storage at Existing Assets (CESEA) at UIUC with the participation of Waste Pressure Corp and Ecotek Engineering USA LLC. CESEA will focus on LDES systems that can integrate to existing infrastructure in a manner that reduces the initial capital expenditure and demonstrates the ability to repurpose fossil assets that would otherwise become stranded, to serve the energy transition. CESEA aims to leverage UIUC’s unique facilities to validate LDES systems performance at a relevant operating environment. UIUC’s facilities include a 85-MW combined heat and power (CHP) power plant, two (2) solar PV plants totaling over 18 MWdc of installed capacity, an electrical grid along with a substation at transmission and distribution voltages, a 22-mile gas pipeline network operating at two pressure levels, along with steam and chilled water distribution networks. The new LDES systems will connect to the existing UIUC grid through a new test electrical station, which will have the capacity to accommodate additional connections to test new devices and technologies as part of future CESEA R&D activities. The test electrical station will contain meters, instrumentation, and controls to accurately capture data and allow optimization of control algorithms. CESEA will initially focus on technologies that: i) utilize existing equipment or facilities to perform at least one of the process steps in LDES (charging, storage, or discharging), ii) leverage mature or commercially available components or controls, iii) show potential for cost-leadership in 10+ hour storage at a commercial scale. Initial technologies that were identified to meet these criteria include Compressed Gas Energy Storage (CGES), and TES. CGES stores electricity by raising the pressure of a compressible gas inside a control volume and converting the stored energy to electricity via expansion-generation. CGES is a generalization of CAES that covers any working gas (not just air). A successful CGES demo will help to circumvent many challenges faced by CAES (long development times due to site prospecting, high cost of compression and storage, heat recovery management, etc.) by: 1) utilizing existing infrastructure (compressors, pipelines, underground storage or pressure vessels) used in the transportation and storage of industrial gases for LDES charging and storage; 2) deploying over sites already-developed for industrial applications with minor additional work; 3) leveraging the price structure of commercial industrial gas to cover the costs of electricity used during charging. A previous DOE-sponsored conceptual study (DE-FE-0032018) estimated the levelized cost of energy of a 1.1 MW / 17 MWh CGES system at $0.08/kWh, with a commercial 10x scale system cost estimated at <$0.04/kWh (Giardinella, 2022). The pilot-sized system was estimated to avoid up to 2693 tons of CO2/year.
25 ENERGY STORAGE↗
Symmetry‐Breaking Strategy Yields Dopant‐Free Small Molecule Hole Transport Materials for Inorganic Perovskite Solar Cells with 20.58% Efficiency and Outstanding Stability
Abstract Inorganic perovskites are known for their excellent photothermal stability; however, the photothermal stability of all‐inorganic n‐i‐p perovskite solar cells (PSCs) is compromised due to ion diffusion and free radical‐induced degradation caused by the use of doped spiro‐OMeTAD hole transport materials (HTMs). In this study, two isomeric donor–acceptor–donor (D–A–D) type small molecules, namely HBT and HiBT, were developed and used as dopant‐free HTMs, using 2,1,3‐benzothiadiazole or benzo[d][1,2,3]thiadiazole as acceptor moieties. The HiBT molecule, with its symmetry‐breaking features, exhibits a large dipole moment, enhanced coordination‐active sites, and a well‐aligned energy level structure, all of which contribute to passivating perovskite surface defects and improving free charge separation. As a result, inorganic CsPbI 3 PSCs with HiBT HTM achieved an impressive power conversion efficiency (PCE) of 20.58%, the highest reported for dopant‐free HTM‐based inorganic PSCs. Moreover, the enhanced hydrophobic properties of HiBT molecules, coupled with their ability to passivate perovskite surface defects, contribute to significantly improved device stability. The unencapsulated devices based on HiBT HTM retained over 83% and 80% of their initial efficiency after being stored at 85 °C for 50 days and undergoing maximum power point (MPP) tracking at 85 °C for 1100 h, respectively. These results highlight that the symmetry‐breaking strategy is an exceptionally effective approach for designing efficient, dopant‐free small molecule HTMs, significantly contributing to both the high efficiency and enhanced stability of all‐inorganic PSCs.
Chemistry↗
Photo-DAC: Light-Driven Ambient-Temperature Direct Air Capture by a Photobase
Direct air capture (DAC) may reduce atmospheric CO 2 concentrations to preindustrial levels, yet the high energies and temperatures involved in current DAC technologies hinder large-scale deployment. In the case of aqueous-based CO 2 absorbents, a large energetic penalty is associated with heating and boiling off water, as required for thermally driven solvent regeneration. This could be avoided via photochemically driven pH swings involving photoacids or photobases, and harnessing abundant and renewable solar energy, though efficient solvent regeneration and recycling in a realistic multicycle DAC process remains challenging. Herein, we report a photochemically driven DAC process (photo-DAC) in which atmospheric CO 2 capture by an aqueous glycylglycine (GlyGly) solution is enabled through a pH swing by a pyridine-substituted diiminoguanidine (PyDIG) photobase. Upon irradiation with UV light, the PyDIG photobase undergoes photoisomerization from the E,E to the Z,Z isomer, corresponding to a pK a increase of 2.8 units that activates GlyGly for DAC through deprotonation. After the GlyGly/PyDIG solvent is saturated with atmospheric carbon dioxide, leaving it in the dark under ambient conditions leads to the isomerization of PyDIG from the Z,Z back to the E,E isomer, which is accompanied by a pH drop and CO 2 release. To demonstrate the recyclability of the GlyGly/PyDIG solvent, we have completed six consecutive DAC cycles, with a measured average cyclic capacity in the range of 0.21–0.26 mol CO 2 per mol of GlyGly/PyDIG. These results open the prospect for energy-efficient DAC cycles completed entirely at ambient conditions, thereby avoiding the significant energy penalties associated with heating and boiling aqueous solvents.
Einkauf, Jeffrey D. [Oak Ridge National Laboratory↗
Carboxyl-functionalized perovskite enables ALD growth of a compact and uniform ion migration barrier
Mixed-halide wide-band-gap perovskites are critical components of highly efficient tandem cells, but their operating stability is limited by halide migration. Metal oxides deposited via atomic layer deposition (ALD) have been shown to block halide migration; however, previously pursued methods result in inhomogeneous nucleation and growth. We hypothesized that functionalizing the perovskite surface with ALD-active carboxyl groups could promote nucleation and enable higher-temperature metal oxide growth. We find that 5-ammonium valeric acid iodide (5-AVAI) facilitates the formation of a compact and uniform aluminum oxide (Al 2 O 3 ) layer and allows growth at 100°C compared with the previous limit of 75°C. We demonstrate that halide migration into the C 60 electron transport layer is reduced by a factor of 10 compared with the reference case. Finally, Al 2 O 3 -capped perovskite solar cells with a band gap of 1.78 eV retain 90% of their initial power conversion efficiency after 1,000 h of continuous operation under 1-sun illumination at 55°C.
Al2O3↗
Agrivoltaic Decision Tools for Perennial and Field Crop Farmers
This article describes a series of spreadsheet-based tools to help farmers estimate costs, revenues, and yields from agricultural production under different configurations of agrivoltaic installations for field and perennial crops. Crop-specific log books allow farmers to project changes in activity-level costs from the field due to agrivoltaic installations. The whole-farm tool helps farmers aggregate activity-level net returns up to the farm level to calculate projections of trade-offs between crop production with or without agrivoltaic installations. We present tools for lettuce and cranberries, but the tools are comprehensive and inclusive and so can be modified for other perennial and field crops.
14 SOLAR ENERGY↗
Data for "High dopant activation in arsenic doped single-crystal CdTe thin films: Insights from MBE growth and rapid thermal processing"
Explore the source record for details and available documents.
14 SOLAR ENERGY↗
Benchmarking DFT Accuracy in Predicting O 1s Binding Energies on Metals
X-ray photoelectron spectroscopy (XPS) is a powerful tool for probing the electronic structure and composition of materials, particularly metals and metal oxides of relevance to solar cells and catalysis. Density functional theory (DFT) is often used to support XPS peak assignments, but its reliability for predicting oxygen species is not well established. Here, we compile a large data set of experimental oxygen binding energies and evaluate corresponding DFT predictions. We find that as the binding energies of metal-bound atomic oxygen species increase, especially above ≈530 eV, there is a general decrease in the accuracy of DFTpredicted values. Thus, high-binding-energy atomic oxygen species, such as those proposed as active for selective Ag-catalyzed epoxidation, are less well represented. The chemical nature of the oxygen species also influences accuracy, with molecularly bound species more reliably captured across the entire range of energies. These findings illustrate the limitations of DFT for interpreting XPS spectra and provide a benchmark for improving computational methods.
Adsorption↗
Developing the Science Basis for Understanding Polymer Encapsulant Degradation Mechanisms: DuraMAT 2.0 Final Project Report
Polymeric encapsulants are essential materials in photovoltaic modules, protecting sensitive electronics from the environment while providing mechanical integrity to the multilayered assembly. However, these polymeric materials are susceptible to degradation processes driven by the ingress of environmental species, ultraviolet radiation, thermal stresses, and mechanical loading. In this study, we employ a combined atomistic simulation and accelerated aging experimental approach to study the molecular-scale mechanisms of encapsulant degradation. Classical molecular dynamics simulations quantify the diffusion of environmental and degradation species through the polymer matrix, producing composition-specific diffusion coefficients. Reactive simulations characterize activation energy barriers and reaction rate constants for key chemical pathways. In parallel, thermal-desorption analyses coupled with mass spectrometry monitor the emergence and concentration profiles of degradation products under controlled stressor conditions. By integrating simulation and experiment, we establish quantitative correlations between polymer composition, species diffusivity, and chemical reactivity. We anticipate that these relations and quantitative values could serve as high-fidelity inputs to reaction-diffusion models, enabling physics-informed lifetime predictions and guiding the design of more durable encapsulant materials for solar energy applications.
36 MATERIALS SCIENCE↗
Colloidal Synthesis of Palladium Nanocluster‐Decorated Cs 3 Sb 2 Cl 9 Perovskite Heterostructural Nanorods for Enhanced CO 2 Photoreduction
Developing efficient and sustainable photocatalysts for CO 2 reduction remains a significant challenge, particularly with environmentally benign materials. Here, in this study, we report the first one-step synthesis of metal–lead-free perovskite heterostructural nanocrystals by decorating Cs 3 Sb 2 Cl 9 perovskite nanorods with size-controlled Pd nanoclusters via a one-step hot-injection method. The resulting Pd-Cs 3 Sb 2 Cl 9 heteronanorods (HNRs) exhibit strong interfacial electronic coupling, enhanced charge separation, and excellent colloidal stability. Transient absorption spectroscopy and DFT calculations reveal a built-in electric field that drives directional electron transfer from the perovskite host to the Pd domains. Under UV irradiation, the Pd-Cs 3 Sb 2 Cl 9 HNRs demonstrate excellent CO 2 photoreduction activity with high CH 4 selectivity, achieving a record apparent quantum yield (AQY) of 2.62% among halide perovskite nanocrystal-based systems with a large electronic yield of 689.3 ± 12.2 µmol·g cat −1 . In situ spectroscopic monitoring and Gibbs free energy analysis further unveil a Pd-facilitated reaction pathway involving stabilization of key intermediates. This work introduces a new class of lead-free perovskite-based heterostructures through a facile one-step synthesis strategy and offers a new design principle for next-generation photocatalysts for solar fuel production.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Covalent Functionalization of Silicon with Plasma-Grown “Fuzzy” Graphene: Robust Aqueous Photoelectrodes for CO 2 Reduction by Molecular Catalysts
Carbon electrodes are ideal for electrochemistry with molecular catalysts, exhibiting facile charge transfer and good stability. Yet for solar-driven catalysis with semiconductor light absorbers, stable semiconductor/carbon interfaces can be difficult to achieve, and carbon’s high optical extinction means it can only be used in ultrathin layers. Here, we demonstrate a plasma-enhanced chemical vapor deposition process that achieves well-controlled deposition of out-of-plane “fuzzy” graphene (FG) on thermally oxidized Si substrates. The resulting Si|FG interfaces possess a silicon oxycarbide (SiOC) interfacial layer, implying covalent bonding between Si and the FG film that is consistent with the mechanical robustness observed from the films. The FG layer is uniform and tunable in thickness and optical transparency by deposition time. Using p-type Si|FG substrates, noncovalent immobilization of cobalt phthalocyanine (CoPc) molecular catalysts was employed for the photoelectrochemical reduction of CO 2 in aqueous solution. The Si|FG|CoPc photocathodes exhibited good catalytic activity, yielding a current density of ∼1 mA/cm 2 , Faradaic efficiency for CO of ∼70% (balance H 2 ), and stable photocurrent for at least 30 h at −1.5 V vs Ag/AgCl under 1-sun illumination. Furthermore, the results suggest that plasma-deposited FG is a robust carbon electrode for molecular catalysts and suitable for further development of aqueous-stable Si photocathodes for CO 2 reduction.
CO2 reduction↗
Frequency-Nadir-Constrained Unit Commitment for Low-Inertia, High-IBR Island Power Systems [Slides]
The process of energy decarbonization in island power systems is accelerated due to the swift integration of inverter-based renewable energy resources (IBRs). The unique features of such systems, including rapid frequency changes resulting from potential generation outages or imbalances due to the unpredictability of renewable power, pose a significant challenge in maintaining the frequency nadir without external support. This paper presents a unit commitment (UC) model with data-driven frequency nadir constraints, including either frequency nadir or minimum inertia requirements, helping to limit frequency deviations after significant generator outages. The constraints are formulated using a linear regression model that takes advantage of real-world, year-long generation scheduling and dynamic simulation data. The efficacy of the proposed UC model is verified through a year-long simulation in an actual island power system using historical weather data. The alternative minimum inertia constraint, derived from actual system operation assumptions, is also evaluated. Findings demonstrate that the proposed frequency nadir constraint notably improves the system's frequency nadir under high photovoltaic (PV) penetration levels, albeit with a slight increase in generation costs, when compared to the alternative minimum inertia constraint.
14 SOLAR ENERGY↗
Fundamental Studies of the Vibrational, Electronic, and Photophysical Properties of Tetrapyrrolic Architectures
The ability to capture and utilize light in the near-ultraviolet (NUV), visible and near-infrared (NIR-I and NIR-II) spectral regions (i.e., 320–400, 400–700, 700–1000, 1000–1700 nm) is essential for any solar-energy conversion scheme. Nature employs chlorophylls and bacteriochlorophylls in light-harvesting architectures to absorb light in the blue and red/NIR regions. Accessory pigments (carotenoids, bilins) augment absorption of the (bacterio)chlorophylls in the green region. The harvested energy is funneled to a reaction center protein, where charge separation occurs. Subsequent migration of the electron and the hole stabilizes and stores the energy from light via redox chemistry. The long-term objective of the Bocian/Holten&Kirmaier/Lindsey research program under this DOE grant has been to develop tetrapyrrole-based molecular architectures that absorb sunlight, funnel energy and separate charge with high efficiency. Integral to the program has been iterative cycles of design, synthesis and characterization that provided deep insights into the relationships between chemical composition, electronic structure, and key static and dynamic properties (vibrational, redox, photophysical, energy/charge transfer) of tetrapyrrolic systems. Such architectures included monomers, dyads, larger arrays, and complexes with accessory components. The objective was to develop molecular designs and guiding principles to enhance current and future energy-conversion schemes. Molecular arrays targeted to address one or more fundamental questions concerning light harvesting and energy/charge transfer were constructed from analogues of the naturally occurring hemes, chlorophylls and bacteriochlorophylls. Diverse, tunable synthetic building blocks were prepared that spanned the three respective tetrapyrrole families, which are the porphyrins, chlorins and bacteriochlorins. Thus, the research focused on porphyrins as well as synthetic surrogates for chlorophylls (chlorins, 13 1 -oxophorbines and chlorin-imides) and bacteriochlorophylls (bacteriochlorins, bacterio-13 1 -oxophorbines and bacteriochlorin-imides), generically termed hydroporphyrins. Although the three tetrapyrrole classes (porphyrins, chlorins and bacteriochlorins) absorb light strongly in the violet-blue spectral region, the long-wavelength absorption band typically lies in the green-orange, red, and NIR regions, respectively, with increasing intensity. Understanding the spectra, electronic structure, and energy/charge-transfer properties of such tetrapyrrolic macrocycles is of central importance for the rational design of molecular architectures for solar-energy conversion. Our integrated program of molecular design and synthesis coupled with a variety of spectroscopic, electrochemical, and computational studies have probed from first principles how structural and electronic properties of tetrapyrrolic macrocycles dictate spectral properties as well as the rates of ground-state hole/electron transfer and excited-state energy flow in multicomponent architectures. Individual molecules and multicomponent architectures were designed to test ideas of fundamental importance, often requiring the development of new synthetic methodology. The members of the collaborative team had almost daily discussions by phone and/or e-mail concerning design of molecules, flow of compounds between the labs, planning of physical characterization studies, discussing results and analysis and integrating into design of next generation architectures, and the preparation of manuscripts. Furthermore, students and postdocs in the different labs routinely communicated with one another to facilitate the advancement of the research activities. In short, a highly integrated and collaborative research program was well established among the groups. The research effort involved molecular design and synthesis of synthetic molecular architectures by the Lindsey group integrated with physicochemical and photophysical characterization by the Bocian group and the Holten&Kirmaier group (Figure 2). The Bocian group carried out electrochemical, electron paramagnetic resonance (EPR), resonance Raman (RR), and Fourier-transform infrared (FT-IR) studies, as well as density functional theory (DFT) calculations and the time-dependent extension (TDDFT) to gain insight into excited-state properties. The Holten&Kirmaier group carried out static and time-resolved absorption and fluorescence spectroscopy studies and simulated absorption spectra using molecular orbital (MO) energies from DFT as input to the four-orbital model to complement the TDDFT calculations. The combined measurements provided understanding of the vibrational/electronic properties of the individual molecules and the changes that occur upon incorporation into multicomponent architectures. This information underpinned elucidating the mechanisms and timescales of ground-state hole/electron transfer and excited-state energy and charge transfer.
14 SOLAR ENERGY↗