SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A method for producing one or more hydroxide solids includes providing a catholyte comprising an electrolyte solution; contacting the catholyte with an electroactive mesh cathode to electrolytically generate hydroxide ions, thereby precipitating the one or more hydroxide solid(s); and removing the one or more hydroxide solids from the surface of the mesh where they may deposit.
For improved understanding of the behavior of Li plasma facing components (PFCs) in the presence of oxygen impurities, we report on the thermal stability of ultrathin (up to 1.0 nm) LiO x films on a titanium-zirconium-molybdenum (TZM) alloy substrate over the temperature range of 310–1400 K. LiO x films were prepared by either post-oxidation of Li films or Li films deposited on an oxygen-precovered TZM surface. Thermal stability of these films was studied using a combination of temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and low-energy ion scattering (LEIS). For post-oxidized Li films, TPD showed that no Li desorption occurred until temperatures above 620 K, and then Li desorbed from the surface via at least three desorption peaks. The O 1s XPS spectra on the post-oxidized films at 310 K indicate the formation of lithium oxide (Li2O) and peroxide/hydroxide (Li 2 O 2 /LiOH). The peroxide/hydroxide converts to oxide after heating to 680 K with no desorption of Li or O 2 , and then this film decomposes to liberate Li into the gas phase while leaving oxygen at the TZM surface. Heating the LiO x films to 1070 K led to a solid-state reaction with surface Mo atoms of the substrate to form a condensed binary lithium molybdenum oxide (LixMoOy) phase, which upon further heating decomposed to liberate gas phase binary lithium molybdenum oxide species. Li deposition on an oxygen-precovered TZM surface formed a complex, highly stable, oxygen rich, Li-O-Mo interfacial oxide. Li desorption from multilayer Li films on oxygen-precovered TZM surfaces occurred in a metallic Li multilayer peak and three other oxide-derived peaks. These results support the improved thermal stability of oxidized lithium as compared to metallic Li and have implications for Mo impurity transport into the plasma at high temperatures.
Temperature locale sensors include an enclosure defining a sealed volume with a phase-change material therein at a known pressure. The phase-change material is formulated to exhibit a gas-to-solid phase change, without condensing to a liquid phase, at the known pressure and a targeted temperature, i.e., the material's “deposition temperature.” The phase-change material—while at least partially in gaseous form, either initially or after sublimation—is exposed to an environment with temperatures varying by location, including a maximum temperature above the phase-change material's deposition temperature and other temperatures at or below the deposition temperature. The gaseous phase-change material, in a location at the deposition temperature, solidifies from its gaseous phase to form solid grain deposits on a surface within the enclosure of the sensor. The solid deposits precisely identify the location of the specific, targeted deposition temperature.
Properties of solid–liquid interfaces and surface charge characteristics mediate ionic and molecular transport through porous systems, affecting many processes such as separations. Herein, we report experiments designed to probe the electrochemical properties of solid–liquid interfaces using a model system of a single polyethylene terephthalate (PET) pore in contact with aqueous and propylene carbonate solutions of LiClO 4 . First, the existence and polarity of surface charges were inferred from current–voltage curves recorded when a pore was placed in contact with a LiClO4 concentration gradient. Second, the electro-osmotic transport of uncharged polystyrene particles through the PET pore provided information on the polarity and the magnitude of the pore walls’ zeta potential. Our experiments show that the PET pores become effectively positively charged when in contact with LiClO 4 solutions in propylene carbonate, even though in aqueous LiClO 4 , the same pores are negatively charged. Additionally, the electro-osmotic velocity of the particles revealed a significantly higher magnitude of the positive zeta potential of the pores in propylene carbonate compared to the magnitude of the negative zeta potential in water. The presented methods of probing the properties of solid–liquid interfaces are expected to be applicable to a wide variety of solid and liquid systems.
A deep understanding of the interaction of the surface of cathode materials with solid electrolytes is crucial to design advanced solid-state batteries (SSBs). This is especially true for the new class of lithium metal chloride (Li-M-Cl) solid electrolytes which are receiving rapidly growing attention due to their very high oxidative stability (>4 V) in combination with good ionic conductivity that can enable long cell cycle life. While Li-M-Cl electrolytes typically contain resource-limited metals (M) such as indium or rare earths, work has focused on substituting M with more abundant elements such as zirconium. Via operando resistance measurements using intermittent current interruption we explore the dynamic evolution of the interphase at the surface of Ni-rich NCM85 or NCM111 cathode particles inside a working SSB with three different Li-(M 1 ,M 2 )-Cl catholytes (Li 3 InCl 6 , Li 2 Sc 1/3 In 1/3 Cl 4 and Li 5/2 Y 1/2 Zr 1/2 Cl 6 ) to reveal the impact of the cationic metal substitution on the interfacial chemistry. We show that the metal plays a critical role in determining high voltage stability, contrary to prior assumptions. Using a combination of cyclic voltammetry and ultraviolet photoelectron spectroscopy measurements of the electronic band structure to assess oxidative stability; coupled with DFT calculations and ToF-SIMS to evaluate products formed at the interface at different upper cutoff potentials and degrees of delithiation, we are able to differentiate between electrochemical and chemical degradation. We find that Li 2 Sc 1/3 In 1/3 Cl 4 yields the highest (and Li 3 InCl 6 the lowest) stability against electrochemical oxidation, while Li 5/2 Y 1/2 Zr 1/2 Cl 6 undergoes a detrimental chemical reaction with oxygen released from Ni-rich NCM85 at high potentials, resulting in fast capacity fading. Altogether, our work establishes a platform for the metrics and an approach that can be utilized to efficiently evaluate the stability of new halide SEs in SSB cells.
Abstract Transpiration cooling is able to provide more uniform coolant coverage than film cooling to effectively protect the component surface from contacting the hot gas. Due to numerous coolant ejection outlets within a small area at the target surface, the experimental thermo-fluid investigation on transpiration cooling becomes a significant challenge. Two classic methods to investigate film cooling, the steady-state foil heater method and the transient thermography technique, fail for transpiration cooling because the foil heater would block numerous coolant outlets, and the semi-infinite solid conduction model no longer holds for porous plates. In this study, a micro-lithography method to fabricate a silver coil pattern on top of the additively manufactured polymer porous media as the surface heater was proposed. The circuit was deliberately designed to cover the solid surface in a combination of series connection, and parallel connection to ensure the power in each unit cell area at the target surface was identical. With uniform heat flux generation, the steady-state tests were conducted to obtain distributions of a pair of parameters, adiabatic cooling effectiveness, and heat transfer coefficient (HTC). The results showed that the adiabatic cooling effectiveness could reach 0.65 with a blowing ratio lower than 0.5. Meanwhile, the heat transfer coefficient ratio (hf/h0) of transpiration cooling was close to 1 with a small blowing ratio at 0.125. A higher HTC ratio was observed for smaller pitch-to-diameter cases due to more turbulence intensity generated at the target surface.
The collection of solid particulates and liquids from surfaces by the use of cloth swipes is fairly ubiquitous. In such methods, there is a continuous concern regarding the ability to locate and quantitatively sample the analyte species from the material. In this effort, we demonstrate the initial coupling of an Advion Plate Express plate reader to a liquid sampling–atmospheric pressure glow discharge (LS-APGD) microplasma ionization source with an Orbitrap mass spectrometer to perform uranium isotopic analyses of solution residues on cotton swipes. The Plate Express employs a sampling probe head to engage and seal against the swipe surface. Subsequentially, the analyte residues are desorbed and transported within a 2% HNO 3 electrolyte flow to the ionization source. Quantitative recoveries were observed following a single 30 s extraction step, with the absolute mass sampled per extraction being ~100 ng. While the intrasample variability in the analytical responses for triplicate sampling of the same swipe yield ~30% RSD, this lack of precision is offset by the ability to determine isotope ratios for enriched uranium specimens with a precision of better than 10% RSD. Pooled, intersample precision ( n = 9) was found to be <5%RSD across the various sample compositions. Finally, 235 U/ 238 U determinations (ranging from 0.053 to 1.806) were accurate with errors of <10%, absolute. The 234 U- and 236 U-inclusive ratios were determined with similar accuracy in enriched samples. While the driving force for the effort is in the realm of nuclear nonproliferation efforts, the ubiquitous use of cloth swipes across many application areas could benefit from this convenient approach, including the use of versatile, reduced-format mass spectrometer systems.
Abstract The continuous rupturing and rebuilding of unstable solid electrolyte interphase (SEI) layer during cycling would block Na + diffusion and induce Na dendrite formation, ultimately limiting the practical application of high‐energy‐density sodium metal batteries. Herein, a hybrid SEI layer containing Li‐species is dexterously constructed on the surface of sodium metal anode. Li‐containing inorganic components (Li 3 N, LiF, and Li 2 CO 3 ) are introduced to stabilize the Na/electrolyte interface and enhance the mechanical and diffusion kinetic properties of the SEI layer, which can reduce the side reactions and gas generation, regulate Na + flux during cycling and promote rapid Na + migration for uniform dendrite‐free Na deposition. As a result, the constructed Na symmetric cells achieve low overpotential and long cycle life of 5900, 1800, and 500 h at current densities of 3, 10, and 30 mA cm −2 , respectively. Furthermore, the full cells paired with the Na₃V₂(PO₄)₃ cathode demonstrate high specific capacity and excellent cycle stability, even at an ultra‐high cathode loading of 39.3 mg cm −2 and a low N/P ratio (negative/positive electrode capacity ratio of 1.21).
Delineating intricate interactions between highly reactive Li-metal electrodes and the diverse constituents of battery electrolytes has been a long-standing scientific challenge in materials design for advanced energy storage devices. Here, we isolated lithium polysulfide anions (LiS 4 - ) from an electrolyte solution based on their mass-to-charge ratio and deposited them on Li-metal electrodes under clean vacuum conditions using ion soft landing (ISL), a highly controlled interface preparation technique. The molecular level precision in the construction of these model interfaces with ISL, coupled with in situ x-ray photoelectron spectroscopy and ab initio theoretical calculations, allowed us to obtain unprecedented insight into the parasitic reactions of well-defined polysulfides on Li-metal electrodes. Our study reveals that the oxide-rich surface layer, which is amenable to direct electron exchange, drives multielectron sulfur oxidation (S o → S 6+ ) processes. Furthermore, our results have substantial implications for the rational design of future Li-S batteries with improved efficiency and durability.
During washing of radiologically impacted building surfaces, penetration of radionuclide ions into complex solids associated with these surfaces may occur. This study investigates the penetration of Cs-137, Sr-85, and Eu-152 solutions into numerous common building materials and radionuclide behavior when these materials were exposed to a static bath or low-pressure flow of tap water, 0.1 M potassium chloride (KCl), and 0.5 M KCl. The decontamination efficacy and the depth profile for residual contamination were measured to determine the conditions under which applying a wash solution has benefit compared to physically removing the surface material. On asphalt, 70-80% of the radionuclides were found to be within 0.02 mm of the surface. Concrete is more porous than asphalt, and 80% of the radionuclides were within 0.2 mm of the surface for Cs-137 and Eu-152 and 50-80% for Sr-85. Water effectively removed all contaminants from hard nonporous surfaces. Finally, this paper illustrates that a wash penalty factor concept-defined as ratio of the depth at which 50% of the radioactivity is found in the washed sample divided by the depth at which 50% of radioactivity is found in the control-can serve as a way to quantify whether the wash method increases the depth at which contamination penetrates into the material and thus the material becomes more difficult to decontaminate.
Evaporation of small water droplets on solids is hindered because surface tension pulls the droplet into a spherical cap that has a small perimeter. Our solution is to coat a solid with a very thin, porous layer into which the droplet flows to create a large-area disk with concomitant high rate of evaporation. We investigate evaporation by varying factors that have not been previously considered: pore size and distribution, contact angle, temperature, and relative humidity (RH). A larger pore size resulted in faster evaporation, which we explain through faster transport within the coating. Even faster evaporation occurred for a bilayer structure with small particles on the air side and larger particles on the solid side. Further, the water advancing contact angle had an insignificant effect in the range from < 10° through to 60°. Our results for different pore sizes, temperature, humidity, and contact angle all collapse onto a single curve when appropriately normalized. This validates an equation that can be used for the evaporation from a homogeneous coating that depends only one empirical factor and the droplet volume. Since the volume is often user-controlled, we envisage that this equation can be used to predict evaporation and guide design of fast-drying coatings.
The separation of electrode active materials from spent Li-ion batteries (LIBs) by froth flotation is challenging due to the changes in surface properties of electrode active materials from cycling as well as the presence of organic binders. In this work, the froth flotation separation of aged anode and cathode composite materials from spent LIBs was systematically investigated after the materials were heat treated. The results show that aged anode and cathode materials from spent LIBs can be well separated from each other after a heating process in air at 400 degrees C and at which some of the PVDF binder remains intact. The underlying mechanism was investigated by X-ray photoelectron spectroscopy (XPS), contact angle measurements, and scanning transmission electron microscopy (STEM) coupled with energy-dispersive X-ray spectroscopy (EDX). The results from the XPS and contact angle measurements show that there is a hydrophilic and oxygen-rich layer on the surface of aged anode materials. This hydrophilic surface, associated with the solid electrolyte interface (SEI) layer, impacts the froth flotation process significantly. The results also show that both the SEI layers and PVDF binder residues on the surface are removed at 400 degrees C for an hour, restoring the hydrophobicity of the anode materials, which, in turn, benefits the separation of anode and cathode materials. The STEM/EDX elemental analysis data confirms that there are 20 nm-thick oxygen-rich SEI layers on the surfaces, which can be removed after a heating process. The present result illustrates the significance of the SEI layers in flotation separation of electrode materials and sheds new lights into the future development of the recycling processes for the separation of anode and cathode composite materials from spent Li-ion batteries.
SRNL analyzed samples from Tank 38H and Tank 43H to support ECP and CCP. The results indicate the concentrations of most species in the Tank 38H surface sample increased from the previous surface sample. The Tank 38H sub-surface sample shows only small changes in concentration for most major species in the solution from the previous sample. The large differences in the concentrations of major components between the Tank 38H surface and sub-surface samples indicate significant stratification of solution species within the tank. The Tank 38H surface and sub-surface samples both contained a small amount of sludge solids (<1 wt%). The Tank 43H surface and sub-surface samples are slightly more dilute than the previous samples. The Tank 43H sub-surface sample exhibits a composition more concentrated than the surface sample indicating some stratification within the tank. The Tank 38H surface and sub-surface sample both show large increases in the concentrations of uranium and plutonium likely due to the presence of sludge solids in both samples. (Note: the samples were digested and analyzed without filtration.) The total uranium concentrations of the two Tank 43H samples are similar to the previous sample results. The plutonium concentration in both Tank 43H samples appear to have decreased from the previous samples; however, the surface sample concentrations are close to the detection limit.
As protonic ceramic electrolysis cells emerge for efficient H 2 production, there is a need to develop air electrode materials enabling fast, durable steam splitting and proton incorporation. Single-phase triple conductors may fail to satisfy the myriad performance/stability requirements, and their critical charge-carriers (holes, oxygen vacancies, and protons) are in competition, limiting their concentrations. Instead, we propose task-sharing, vertically aligned nanocomposites (VANs), comprising a proton conductor (BaZr 0.9 Y 0.1 O 3-δ ) and a redox-active mixed ionic electronic conductor (Ce 0.9 Pr 0.1 O 2-δ ), that may enable rapid proton surface exchange at the solid–gas interface and transport along the solid–solid heterointerfaces. We grew VANs by pulsed laser deposition and investigated the interplay between their processing conditions, structure, and proton and oxygen surface exchange kinetics. We varied the substrate temperature, laser repetition rate, laser fluence, and processing oxygen pressure. The crystallinity and phases were characterized by grazing-incidence X-ray diffraction, and the strain and structural order as a function of depth were evaluated by angle-dependent synchrotron X-ray pair distribution function analysis. To evaluate the potential for interdiffusion, the formation energies of substitutional defects were simulated with density functional theory. Corresponding structural analysis and elemental mapping were performed by scanning/transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electron energy-loss spectroscopy, indicating distinct nanoscale compositional regions with a hierarchical structure embedded in individual VANs columns and minimal interdiffusion across a bilayer film. Proton and oxygen surface exchange coefficients (k H , k O ) and polarization resistances were evaluated by electrical and optical relaxations and impedance spectroscopy of VAN-incorporated protonic ceramic electrochemical cells, respectively, at 400–500 °C, demonstrating values comparable to some of the best-known triple and mixed conductors.
As the main components of Portland cement, calcium silicates show substantial differences in their hydration reactivity which have not been fully explained. A comprehensive comparison of the initial hydration process of calcium silicates, namely dicalcium silicate (C{sub 2}S) and tricalcium silicate (C{sub 3}S), was conducted using molecular dynamics simulations. The initial hydration process was divided into three stages using cut-off times of 0.001 ns and 3 ns. The hydration of M{sub 3}-C{sub 3}S (010) was more evident than that of β-C{sub 2}S (100), supported by the hydroxylation degree, radial distribution function, atomic density profile, etc. The coordination number of the surface Ca atoms might be the underlying reason for such a difference. Interactions between cement surfaces and water molecules were mainly characterised by solid OH bonding and Ca-water O bonding. Dissolution of Ca atoms was observed, although quite scarce, while no dissolution of Si atoms was observed.
Considerable attention has been directed to understanding the influence of heterointerfaces between Ruddlesden–Popper (RP) phases and ABO 3 perovskites on the kinetics of oxygen electrocatalysis at elevated temperatures. Here, we report the effect of heterointerfaces on the oxygen surface exchange kinetics by employing heteroepitaxial oxide thin films formed by decorating LaNiO 3 (LNO) on La 1.85 Sr 0.15 CuO 4 (LSCO) thin films. Regardless of LNO decoration, tensile in-plane strain on LSCO films does not change. The oxygen surface exchange coefficients (kchem) of LSCO films extracted from electrical conductivity relaxation curves significantly increase with partial decorations of LNO, whereas full LNO coverage leads to the reduction in the kchem of LSCO films. The activation energy for oxygen exchange in LSCO films significantly decreases with partial LNO decorations in contrast with the full coverage of LNO. Optical spectroscopy reveals the increased oxygen vacancies in the partially covered LSCO films relative to the undecorated LSCO film. We attribute the enhanced oxygen surface exchange kinetics of LSCO to the increased oxygen vacancies by creating the heterointerface between LSCO and LNO.
This project established quantitative links between inner‑sphere chemistry (active metal identity, coordination, and zeolite topology) and outer‑sphere organization (solvent identity, hydrogen‑bond networks, and pore condensation) that govern rates, activation barriers, and selectivities for alkene epoxidation and epoxide ring‑opening at solid–liquid and quasi‑liquid–solid interfaces. We deconvoluted contributions from covalent interactions at active sites and noncovalent, solvent‑mediated interactions within pores by pairing well‑defined metal substituted zeolites with controlled solvent environments. We then mapped those contributions onto measurable kinetics (ΔH‡, ΔS‡), adsorption thermodynamics (ITC), and in situ spectroscopy. The transferrable outcomes include a set of design rules that include the following understandings. First, tune silanol ((SiOH)x) density and pore topology to organize solvent networks that selectively stabilize transition states. Second, exploit activity‑coefficient‑normalized rates and adsorption– barrier correlations to diagnose when solvent reorganization rather than surface chemistry limits performance. Third, use partial pore condensation (e.g., acetonitrile, water but also generalizable to other solvents) to elicit liquid‑like stabilization effects even in nominally vapor‑phase reactors. Collectively, these results provide strategies to increase epoxidation rates, improve oxidant utilization (i.e., selectivities), and steer regioselectivity in zeolite‑based catalytic processes relevant to sustainable oxidation chemistry. These outcomes should be transferable to other classes of reactions that proceed in microporous materials and under confinement provided by organized solvents (e.g., electrochemical double layers).
This report contains the characterization of six 200-mL Tank 48H samples: HTF-48-21-74, HTF-48-21-75, HTF-48-21-76, HTF-48-21-81, HTF-48-21-82, and HTF-48-21-83. The effort supports a Systems Engineering Evaluation (SEE) recommendation involving a Tank 48H decantation strategy that would remove liquid volume and grout the solids. The first three Tank 48H samples were surface samples taken after a quiescent period in the tank. The quiescent period allowed settling of the solids, these being mostly potassium tetraphenylborate. These three surface samples had no measurable solids, though a settling haze could be seen. The latter three samples were taken at 48, 25, and 10 inches from the bottom of Tank 48H immediately after tank mixing pumps had been run. Those samples contained measurable insoluble solids that were readily visible. All six samples were analyzed to provide chemical and radionuclide concentrations as defined as the "Limit" and "Target" in the Saltstone Production Facility (SPF) Waste Acceptance Criteria (WAC) and per the compliance strategy in the Tank Farm Waste Compliance Plan (WCP). Samples were analyzed by many methods to determine pH, density/specific gravity, radioactive isotopes, soluble and insoluble elements, total solids, total insoluble solids, organic and inorganic mercury, volatile and semi-volatile chemicals, and anions. Photographs of the settling of small samples were taken over time and are displayed in this report. The extent of settling was very significant, showing that surface sample liquids are similar to filtrates. However, Cs-137 measurements exceeded WAC limits in all surface samples (1.1E+07 vs. 1.3E+06). The solids were found to contain very high cesium activity, measured as high as 1.1E+10 dpm/gram. Sodium was in the range of 4.24 to 4.74 M for all samples, so the solids would tend to settle with time and would not be at risk of floating without air entrainment. No organic mercury was detected in this work.