Search NASA⌕ Search

SEARCH · Search NASA

Results for “SPAN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Pressure-distribution measurements on a tapered wing with a partial-span split flap in curved flight

Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and the yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degree pitch; 0 degree, 5 degree, and 10 degree yaw; and with split flaps covering 25, 50, 75, and 100 percent of the wing span and deflected 60 degrees. The results are given in the form of load distributions and as calculated moment coefficients. The experimental values of rolling- and yawing- moment coefficients were in fairly close agreement with theory.

Troller, TH↗
NASA NTRS1941

The calculation of span LCAD distributions of swept-back wings

Span load distributions of swept-back wings have been calculated. The method used was to replace the wing with a bound vortex at the quarter-chord line and to calculate the downwash due to the system of bound and trailing vortices to conform at the three-quarter-chord line to the slope of the flat-plate wing surface. Results are given for constant-chord and 5:1 tapered plan forms, for sweep-back angles of 0 degrees, 30 degrees, and 45 degrees, and for aspect ratios of 3, 6, and 9. Some comments on the stalling of swept-back wings are included.

Mutterperl, William↗
NASA NTRS1948

Free-flight Investigation at Transonic and Supersonic Speeds of the Rolling Effectiveness of a 42.7 Degree Sweptback Wing Having Partial-span Ailerons

An investigation of the rolling effectiveness at transonic and supersonic speeds of partial-span ailerons on a 42.7 degree sweptback wing having symmetrical circular-arc airfoil sections of 10-percent thickness ratio normal to the wing quarter-chord line has been made by means of rocket-propelled test vehicles. The results are compared with results of a supersonic wind-tunnel test at Mach number 1.9.

CONTROLS, LATERAL↗
NASA NTRS1954

Effect of Ice Formations on Section Drag of Swept NACA 63A-009 Airfoil with Partical-span Leading-edge Slat for Various Modes of Thermal Ice Protection

Studies were made to determine the effect of ice formations on the section drag of a 6.9-foot-chord 36 degree swept NACA 63A-009 airfoil with partial-span leading-edge slat. In general, the icing of a thin swept airfoil will result in greater aerodynamic penalties than for a thick unswept airfoil. Glaze-ice formations at the leading edge of the airfoil caused large increases in section drag even at liquid-water content of 0.39 gram per cubic meter. The use of an ice-free parting strip in the stagnation region caused a negligible change in drag compared with a completely unheated airfoil. Cyclic de-icing when properly applied caused the drag to decrease almost to the bare-airfoil drag value.

PROTUBERANCES - BODIES↗
NASA NTRS1956

Heat-requirements for Ice Protection of a Cyclically Gas-heated, 36 Degree Swept Airfoil with Partial-span Leading-edge Slat

Heating requirements for satisfactory cyclic de-icing over a wide range of icing and operating conditions have been determined for a gas-heated, 36deg swept airfoil of 6.9-foot chord with a partial-span leading-edge slat. Comparisons of heating requirements and effectiveness were made between the slatted and unslatted portions of the airfoil. Studies were also made comparing cyclic de-icing with continuous anti-icing, and cycll.cde-icing systems with and without leading-edge ice-free parting strips. De-icing heat requirements were approximately the same with either heated or unheated parting strips because of the aerodynamic effects of the 36deg sweep angle and the spanwise saw-tooth profile of leading-edge glaze-ice deposits. Cyclic de-icing heat-source requirements were found to be one-fourth or less of the heat requirements for complete anti-icing. The primary factors that affected the performance of the cyclic de-icing heating system were ambient air temperature, heat distribution, and thermal lag.

Gray, Vernon H↗
NASA NTRS1953

On the application of transonic similarity rules to wings of finite span

The transonic aerodynamic characteristics of wings of finite span are discussed from the point of view of a unified small perturbation theory for subsonic, transonic, and supersonic flows about thin wings. This approach avoids certain ambiguities which appear if one studies transonic flows by means of equations derived under the more restrictive assumption that the local velocities are everywhere close to sonic velocity. The relation between the two methods of analysis of transonic flow is examined, the similarity rules and known solutions of transonic flow theory are reviewed, and the asymptotic behavior of the lift, drag, and pitching-moment characteristics of wings of large and small aspect ratio is discussed. It is shown that certain methods of data presentation are advantageous for the effective display of these characteristics.

Spreiter, John R↗
NASA NTRS1957

Measurement of Aerodynamic Forces for Various Mean Angles of Attack on an Airfoil Oscillating in Pitch and on Two Finite-span Wings Oscillating in Bending with Emphasis on Damping in the Stall

The oscillating air forces on a two-dimensional wing oscillating in pitch about the midchord have been measured at various mean angles of attack and at Mach numbers of 0.35 and 0.7. The magnitudes of normal-force and pitching-moment coefficients were much higher at high angles of attack than at low angles of attack for some conditions. Large regions of negative damping in pitch were found, and it was shown that the effect of increasing the Mach number 0.35 to 0.7 was to decrease the initial angle of attack at which negative damping occurred. Measurements of the aerodynamic damping of a 10-percent-thick and of a 3-percent-thick finite-span wing oscillating in the first bending mode indicate no regions of negative damping for this type of motion over the range of variables covered. The damping measured at high angles of attack was generally larger than that at low angles of attack. (author)

Rainey, A Gerald↗
NASA NTRS1931

A proof of the theorem regarding the distribution of lift over the span for minimum induced drag

The proof of the theorem that the elliptical distribution of lift over the span is that which will give rise to the minimum induced drag has been given in a variety of ways, generally speaking too difficult to be readily followed by the graduate of the average good technical school of the present day. In the form of proof this report makes an effort to bring the matter more readily within the grasp of this class of readers.

Durand, W F↗
NASA NTRS1936

Flight Investigation of Lateral Control Devices for Use with Full-Span Flaps

This report presents the results of flight tests made on five different lateral control devices that appeared adaptable to wings fitted with full span flaps: controllable auxiliary airfoils (airfoils mounted above and forward of the leading edge of the wings), external ailerons (airfoils mounted above the wing and slightly forward of its maximum ordinate), upper-surface ailerons (similar to split trailing-edge flaps except that they constitute the upper surface of the wing), ailerons that retract into the wing when in neutral, and narrow-chord conventional ailerons in combination with a special type of split flap that retracts into the under surface of the wing forward of the ailerons. The devices were tested on a small parasol monoplane. Experienced gained in the use of flaps during these tests has indicated the desirability of a flap that can be operated quickly and easily.

Soule, H A↗
NASA NTRS1937

Pressure Distribution Over a Rectangular Airfoil with a Partial-Span Split Flap

This report presents the results of pressure-distribution tests of a Clark y wing model with a partial-span split flap made to determine the distribution of air loads over both the wing and the flap. The model was used in conjunction with a reflection plane in the NACA 7 by 10 foot wind tunnel. The 20-percent-chord split flap extended over the inboard 60 percent of the semispan. The tests were made at various flap deflections up to 45 degrees and covered a range of angles of attack from zero lift to approximately maximum lift for each deflection.

Wenzinger, Carl J↗
NASA NTRS1939

Calculation of the aerodynamic characteristics of tapered wings with partial-span flaps

Factors derived from wing theory are presented. By means of these factors, the angle of zero lift, the lift-curve slope, the pitching moment, the aerodynamic-center position, and the induced drag of tapered wings with partial-span flaps may be calculated. The factors are given for wings of aspect ratios 6 and 10 , of taper ratios from 0.25 to 1.00, and with flaps of various length. An example is presented of the method of application of the factors. Fair agreement with experimental results is shown for two wings of different taper ratio having plain flaps of various spacing.

Person, Henry A↗
NASA NTRS1941

Wind-tunnel investigation of spoiler, deflector, and slot lateral-control devices on wings with full-span split and slotted flaps

Report presents the results of an extensive investigation made in the NACA 7 by 10-foot wind tunnel of spoiler, deflector, and slot types of lateral-control device on wings with full-span split and slotted flaps. The static rolling and yawing moments were determined for all the devices tested, and the static hinge moments and the time response were determined for a few devices of each type.

Wenzinger, Carl J↗
NASA NTRS1944

Effects of Small Angles of Sweep and Moderate Amounts of Dihedral on Stalling and Lateral Characteristics of a Wing-Fuselage Combination Equipped with Partial- and Full-Span Double Slotted Flaps

Tests of a wing-fuselage combinations incorporating NACA 65-series airfoil sections were conducted in the NACA 19-foot pressure tunnel. The investigation included the tests with flaps neutral and with partial- and full-span double slotted flaps deflected to determine the effects of (1) variations of wing sweep between -4 degrees and 8 degrees on stalling and lateral stability and control characteristics and (2) variations of dihedral between 0 degree and 6.75 degrees on lateral stability characteristics.

Teplitz, Jerome↗
NASA NTRS1950

Some theoretical low-speed span loading characteristics of swept wings in roll and sideslip

The Weissinger method for determining additional span loading for incompressible flow is used to find the damping in roll, the lateral center of pressure of the rolling for wing plan forms of various aspect ratios, taper ratios, and sweep angles. In addition, the applicability of the method to the determination of certain other aerodynamic derivatives is investigated, and corrections for the first-order effects of compressibility are indicated. The agreement obtained between experimentally and theoretically determined values for the aerodynamic coefficients indicates that the method of Weissinger is well suited to the calculation of such resulting aerodynamic derivatives of wings as do not involve considerations of tip suction.

Bird, John D↗
NASA NTRS1940

Effect of wing loading, aspect ratio, and span loading of flight performances

An investigation is made of the possible improvements in maximum, cruising, and climbing speeds attainable through increase in the wing loading. The decrease in wing area was considered for the two cases of constant aspect ratio and constant span loading. For a definite flight condition, an investigation is made to determine what loss in flight performance must be sustained if, for given reasons, certain wing loadings are not to be exceeded. With the aid of these general investigations, the trend with respect to wing loading is indicated and the requirements to be imposed on the landing aids are discussed

Gothert, B↗
NASA NTRS1994

Semi-span model testing in the national transonic facility

The present work was motivated by an ongoing research program at NASA Langley Research Center to develop a semi-span testing capability for the National Transonic Facility (NTF). This test technique is being investigated as a means to design and optimize high-lift devices at flight Reynolds numbers in a ground test facility. Even though the freestream Mach numbers of interest are around .20, the flow around a transport wing with high lift devices deployed may contain regions of compressible flow. Thus to properly model the flow physics, a compressible flow solver may be required. However, the application of a compressible flow solver at low Mach numbers can be problematic. The objective of this phase of the project is to directly compare the performance of two widely used three-dimensional compressible Navier-Stokes solvers at low Mach numbers to both experimental data and to results obtained from an incompressible Navier-Stokes solver. The geometries of interest are two isolated wings with different leading edge sweep angles. The compressible Navier-Stokes solvers chosen, TLNS3D-MB and CFL3D, which were developed at NASA Langley Research Center (LaRC), represent the current state-of-the-art in compressible 3-D Navier-Stokes solvers. The incompressible Navier-Stokes solver, INS3D-UP, developed recently at NASA Ames Research Center (ARC), represents the current state-of-the-art in incompressible Navier-Stokes solvers.

Chokani, Ndaona↗
NASA NTRS1994

Vibration reduction in helicopter rotors using an actively controlled partial span trailing edge flap located on the blade

This report describes an analytical study of vibration reduction in a four-bladed helicopter rotor using an actively controlled, partial span, trailing edge flap located on the blade. The vibration reduction produced by the actively controlled flap (ACF) is compared with that obtained using individual blade control (IBC), in which the entire blade is oscillated in pitch. For both cases a deterministic feedback controller is implemented to reduce the 4/rev hub loads. For all cases considered, the ACF produced vibration reduction comparable with that obtained using IBC, but consumed only 10-30% of the power required to implement IBC. A careful parametric study is conducted to determine the influence of blade torsional stiffness, spanwise location of the control flap, and hinge moment correction on the vibration reduction characteristics of the ACF. The results clearly demonstrate the feasibility of this new approach to vibration reduction. It should be emphasized than the ACF, used together with a conventional swashplate, is completely decoupled from the primary flight control system and thus it has no influence on the airworthiness of the helicopter. This attribute is potentially a significant advantage when compared to IBC.

Millott, T. A.↗