Search NASA⌕ Search

SEARCH · Search NASA

Results for “STAGNATION REGION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Endwall heat transfer in the junction region of a circular cylinder normal to a flat plate at 30 and 60 degrees from stagnation point of the cylinder

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

Nagamatsu, H. T.↗
NASA NTRS1980

A rapid method for the approximate determination of nonlinear solutions Application to aerodynamic flows

A method for determining highly accurate approximations to families of strongly nonlinear solutions which are either continuous or discontinuous, and which represent variations in some arbitrary parameters, is developed and evaluated. The procedure consists of defining a unit perturbation by employing two or more nonlinear solutions which differ from one another by a nominal change in some geometric or flow parameter, and then using that unit perturbation to predict a family of related nonlinear solutions over a range of parameter variation. Coordinate straining is used in determining the unit perturbation to account for the movement of discontinuities and maxima of high-gradient regions due to the perturbation. Although the procedure is generally applicable, results are presented here for nonlinear aerodynamic applications. Attention is focused in particular on transonic flows which are strongly supercritical and exhibit large surface shock movement over the parametric range studied; and on subsonic flows which display large pressure variations in the stagnation and peak suction pressure regions. Flows past both isolated airfoils and compressor cascades involving a variety of flow and geometry parameter changes are considered. Comparisons with the corresponding 'exact' nonlinear solutions indicate a remarkable accuracy and range of validity of such a procedure. Computational time is trivial.

Stahara, S. S.↗
NASA NTRS1981

A rapid perturbation procedure for determining nonlinear flow solutions: Application to transonic turbomachinery flows

Perturbation procedures and associated computational codes for determining nonlinear flow solutions were developed to establish a method for minimizing computational requirements associated with parametric studies of transonic flows in turbomachines. The procedure that was developed and evaluated was found to be capable of determining highly accurate approximations to families of strongly nonlinear solutions which are either continuous or discontinuous, and which represent variations in some arbitrary parameter. Coordinate straining is employed to account for the movement of discontinuities and maxima of high gradient regions due to the perturbation. The development and results reported are for the single parameter perturbation problem. Flows past both isolated airfoils and compressor cascades involving a wide variety of flow and geometry parameter changes are reported. Attention is focused in particular on transonic flows which are strongly supercritical and exhibit large surface shock movement over the parametric range studied; and on subsonic flows which display large pressure variations in the stagnation and peak suction pressure regions. Comparisons with the corresponding 'exact' nonlinear solutions indicate a remarkable accuracy and range of validity of such a procedure.

Stahara, S. S.↗
NASA NTRS1981

Energy efficient engine, high-pressure turbine cooling model technology report

Two dimensional flow visualization model tests were used to substantiate the flow stability benefits derived from the use of turning vanes in the root and tip turn flow areas. Results indicate the need for corner fillets and flow injection into the acute corner formed by the intersection of the rib and simulated airfoil suction surface in order to minimize recirculation (stagnation) of flow in that region. Three dimensional flow visualization model tests verified the actual blade coolant passage design.

Gardner, W. B.↗
NASA NTRS1974

Heating analysis for the Pioneer Venus multiprobe mission

The fully coupled, radiating flow field around the entry probes is determined from a detailed calculation which includes equilibrium chemistry, nongray radiative transport, ablation product injection, and a laminar or turbulent boundary layer. Results show that the radiative flux toward the body is attenuated in the boundary layer at downstream regions of the body as well as at the stagnation point and that, even when radiation absorption by ablation products is accounted for, the radiative heating rates along the downstream regions of the body can, under certain conditions, exceed the stagnation point values. It is also shown that, for Venusian entry, the spectral distribution of radiative flux and the magnitude of radiation absorption by ablation products depend strongly on entry velocity, and that the state of the boundary layer can significantly influence the amount of ablation product absorption or emission that occurs in various spectral regions.

Sutton, K.↗
NASA NTRS1979

Modeling of Radiative Heating in Base Region of Jovian Entry Probe

A theoretical model is derived to determine the average thermodynamic properties in the expanding region, recirculating region, recompression region, and neck region through application of one-dimensional conservation equations. Radiative transfer is calculated using spectrally detailed computer codes accounting for nonequilibrium. The results show that the most severe heating occurs immediately behind the frustum, and that the recompression and neck regions are the major sources of radiation that heats the base stagnation point, The radiation flux to the base point is slightly stronger with ablation than without. Its value is 0.11(43 P(sub b)/P(sub s))(sup 2) times that to the front stagnation point where the base pressure P(sub b) is defined as the average pressure in the recirculating region and P(sub s) is the front stagnation-point pressure. The time-integrated heat load to the base point is 18(43 P(sub b)/P(sub s))(sup 2) kJ/sq cm.

Park, Chul↗
NASA NTRS1978

Methods used for Space Shuttle SRB thrust shape design

Optimization of the Space Shuttle trajectory is discussed with reference to the low acceleration profile required for Shuttle missions. Static tests of the nominal flight curve are described in terms of impulse requirements, vacuum thrust, and burn time. Attention is given to BARF (Burning Anomaly Rate Factor), and it is noted that mandrel fabrication is intended to include the flexibility to counter BARF, should it occur. Test results are presented in which both BARF and specific impulse are considered as independent variables. It was found that no erosive burning occurred, BARF did not occur, specific impulse was on the order of 265 sec, and flow anomalies in the star region produced head-to-aft stagnation pressure drops in excess of theoretical predictions. In other areas, good agreement is noted between theoretical prediction and empirical data.

Baker, J.↗
NASA NTRS1985

End-wall and profile losses in a low-speed axial flow compressor rotor

The blade-to-blade variation of relative stagnation pressure losses in the tip region inside the rotor of a single-stage, axial-flow compressor, is presented and interpreted in this paper. The losses are measured at two flow coefficients (one at the design point and the other at the near peak pressure rise point) to discern the effect of blade loading on the end-wall losses. The tip clearance losses are found to increase with an increase in the pressure rise coefficient. The losses away from the tip region and near the hub regions are measured downstream. The losses are integrated and interpreted in this paper.

Lakshminarayana, B.↗
NASA NTRS1993

Surface hot-film method for the measurement of transition, separation and reattachment points

A real-time method of determining positions of laminar-to-turbulent transition region, separation and reattachment points and stagnation points using an array of simultaneously operated surface-mounted hot-film sensors has been developed and applied to a wind-tunnel test of a multielement airfoil model. Determination of various types of transitions and flow directions in various regimes of flows seen on multielement airfoils are possible without precise sensor calibration or laborious post-test data analysis. The results agree with established method and theoretical methods, but determination of turbulent reattachment points are not yet satisfactory.

Nakayama, Akihiko↗
NASA NTRS1993

Aerodynamic heating environment definition/thermal protection system selection for the HL-20

Definition of the aerothermal environment is critical to any vehicle such as the HL-20 Personnel Launch System that operates within the hypersonic flight regime. Selection of an appropriate thermal protection system design is highly dependent on the accuracy of the heating-environment prediction. It is demonstrated that the entry environment determines the thermal protection system design for this vehicle. The methods used to predict the thermal environment for the HL-20 Personnel Launch System vehicle are described. Comparisons of the engineering solutions with computational fluid dynamic predictions, as well as wind-tunnel test results, show good agreement. The aeroheating predictions over several critical regions of the vehicle, including the stagnation areas of the nose and leading edges, windward centerline and wing surfaces, and leeward surfaces, are discussed. Results of predictions based on the engineering methods found within the MINIVER aerodynamic heating code are used in conjunction with the results of the extensive wind-tunnel tests on this configuration to define a flight thermal environment. Finally, the selection of the thermal protection system based on these predictions and current technology is described.

Wurster, K. E.↗
NASA NTRS1981

Influence of thermal boundary conditions on heat transfer from a cylinder in cross flow

Local heat transfer data over the leading surface of a cylinder in crossflow were obtained for a Reynolds number range of 50,000. The cylinder was operated at both uniform-wall-temperature and uniform-heat-flux thermal ance of 80 deg from the front stagnation point, the uniform-wall-temperature heat transfer coefficients were as much as 66 percent lower than the uniform-heat-flux data. Between the stagnation point and 60 deg around the cylinder, there were no significant differences in the data. This region of the cylinder is within the cylindrical curvature region of the front end of a real turbine so it was concluded that either thermal boundary condition could be used to model turbine flow over that region of the blade. Results of evaluating the exponent x in the fundamental relationship Nu=f(Re) sup x, which is used in data correlation show the exponent varies as a function of local position on the cylinder even in the laminar flow region. The value of x increases linearly from 0.50 at the stagnation point to 0.59 at 60 deg around the cylinder. This linear trend continued into the separation region at 80 deg for the uniform-wall-temperature data, but x increased markedly in the separation region for the uniform-heat-flux data.

Papell, S. S.↗
NASA NTRS1992

In-flight detection of flow separation, stagnation, and transition

Flight tests were conducted to demonstrate the feasibility of simultaneous determination of: (1) boundary-layer instability and transition characteristics; (2) flow separation region; and (3) the location of the leading-edge stagnation point. Surface mounted, multi-element, micro-thin, hot-film sensors were used in conjunction with a bank of constant-temperature anemometers and a PC-based 8-channel simultaneous data acquisition system. Conventional techniques were used to determine the boundary-layer instability and transition characteristics while the flow separation and the stagnation points were determined through the presence of phase reversal signatures.

Mangalam, S. M.↗
NASA NTRS1975

Analysis of atmospheric flow over a surface protrusion using the turbulence kinetic energy equation

Atmospheric flow fields resulting from a semi-elliptical surface obstruction in an otherwise horizontally homogeneous statistically stationary flow are modelled with the boundary-layer/Boussinesq-approximation of the governing equation of fluid mechanics. The turbulence kinetic energy equation is used to determine the dissipative effects of turbulent shear on the mean flow. Mean-flow results are compared with those given in a previous paper where the same problem was attacked using a Prandtl mixing-length hypothesis. Iso-lines of turbulence kinetic energy and turbulence intensity are plotted in the plane of the flow. They highlight regions of high turbulence intensity in the stagnation zone and sharp gradients in intensity along the transition from adverse to favourable pressure gradient.

Frost, W.↗
NASA NTRS1975

Analysis of atmospheric flow over a surface protrusion using the turbulence kinetic energy equation with reference to aeronautical operating systems

Flow over surface obstructions can produce significantly large wind shears such that adverse flying conditions can occur for aeronautical systems (helicopters, STOL vehicles, etc.). Atmospheric flow fields resulting from a semi-elliptical surface obstruction in an otherwise horizontally homogeneous statistically stationary flow are modelled with the boundary-layer/Boussinesq-approximation of the governing equation of fluid mechanics. The turbulence kinetic energy equation is used to determine the dissipative effects of turbulent shear on the mean flow. Iso-lines of turbulence kinetic energy and turbulence intensity are plotted in the plane of the flow and highlight regions of high turbulence intensity in the stagnation zone and sharp gradients in intensity along the transition from adverse to favourable pressure gradient. Discussion of the effects of the disturbed wind field in CTOL and STOL aircraft flight path and obstruction clearance standards is given. The results indicate that closer inspection of these presently recommended standards as influenced by wind over irregular terrains is required.

Frost, W.↗
NASA NTRS1977

Impact conditions required for formation of melt by jetting in silicates

It is demonstrated that the process of jetting which occurs when particles collide at oblique angles may produce melt at much lower velocities than are required for melt production in head-on collisions. The minimum velocities of impact required for jetting in aluminum, bronzitite, dunite, and quartz are calculated by the method of shock polars. The analysis, which depends on stated assumptions about attained pressures and the occurrence of jetting, uses shock-velocity particle-velocity equations of state with three shock regimes. The treatment indicates that jetting should arise in bronzitite, dunite, and quartz at relative velocities as low as 1-2 km/sec. At such velocities material which passes near the stagnation point in the jet-forming region is subjected to sufficiently high pressures so that it is probably melted.

Kieffer, S. W.↗
NASA NTRS1985

A review of some approximate methods used in aerodynamic heating analyses

It is pointed out that preliminary design and optimization studies for new aerospace vehicles require techniques which can calculate aerodynamic heating rates accurately and efficiently. The method employed to calculate the flow field depends to a large extent on the shape of the vehicle, Mach number, Reynolds number, and Knudsen number. In the case of the aero-assisted orbital transfer vehicle (AOTV), a substantial portion of the flight will be in the transitional regime between continuum and free molecule flow. The present paper discusses some approximate methods which have been used to calculate heating rates on high-speed vehicles. Attention is given to the stagnation point and leading edges, the downstream region, the axisymmetric analog, laminar and turbulent heating rates, transition heating rates, gas models, and three-dimensional applications.

Dejarnette, F. R.↗
NASA NTRS1994

Close-up analysis of inflight ice accretion

The objective of this effort was to validate in flight, data that has been gathered in the NASA Lewis Research Center's Icing Research Tunnel (IRT) over the past several years. All data was acquired in flight on the NASA Lewis Research Center's Twin Otter Icing Research Aircraft. A faired 3.5 in. diameter metal-clad cylinder exposed to the natural icing environment was observed by a close-up video camera. The grazing angle video footage was recorded to S-VHS video tape and after the icing encounter, the resultant ice shape was documented by 35 mm photography and pencil tracings. The feather growth area was of primary interest; however, all regions of the ice accretion, from the stagnation line to the aft edge of run back were observed and recorded. After analysis of the recorded data several interesting points became evident: (1) the measured flight feather growth rate is consistent with IRT values, (2) the feather growth rate appears to be influenced by droplet size, (3) the feathers were straighter in the lower, spottier LWC of flight in comparison to those observed in the IRT, (4) feather shedding and ice sublimation may be significant to the final ice shape, and (5) the snow encountered on these flights appeared to have little influence on ice growth.

Reehorst, Andrew L.↗