Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separated Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Shock strength effects on separated flows in non-equilibrium chemically reacting air - Shock wave/boundary layer interaction

This work is part of a general study to examine the effects of nonequilibrium chemical reactions on hypersonic separated flows. In particular, the work presented is the first attempt to quantitatively predict the effects of impinging shock strength on the separation region in non-equilibrium chemically reacting air over a flat plate. Of special interest is the local heat transfer rate to the plate at the reattachment point. The effects of chemically non-equilibrium on the flow field are assessed by making direct comparisons to the results calculated assuming a calorically perfect flow. Chemical reactions are found to increase heat transfer rates, and this increase becomes significantly larger as Reynolds number increases.

Ballaro, Charles A.↗

Experimental studies of flow separation and stalling on two-dimensional airfoils at low speeds. Phase 2: Studies with Fowler flap extended

Results were given on experimental studies of flow separation and stalling on a two-dimensional GA(W)-1 17 percent thick airfoil with an extended Fowler flap. Experimental velocity profiles obtained from a five tube probe survey with optimum flap gap and overlap setting (flap at 40 deg) are shown at various stations above, below, and behind the airfoil/flap combination for various angles of attack. The typical zones of steady flow, intermittent turbulence, and large scale turbulence were obtained from a hot wire anemometer survey and are depicted graphically for an angle of attack of 12.5 deg. Local skin friction distributions were obtained and are given for various angles of attack. Computer plots of the boundary layer profiles are shown for the case of the flap at 40 deg. Static pressure contours are also given. A GA(W)-2 section model was fabricated with 30 percent Fowler flaps and with pressure tabs.

Seetharam, H. C.↗

Development of an Axisymmetric Afterbody Test Case for Turbulent Flow Separation Validation

As identified in the CFD Vision 2030 Study commissioned by NASA, validation of advanced RANS models and scale-resolving methods for computing turbulent flows must be supported by improvements in high-quality experiments designed specifically for CFD implementation. A new test platform referred to as the Axisymmetric Afterbody allows for a range of flow behaviors to be studied on interchangeable afterbodies while facilitating access to higher Reynolds number facilities. A priori RANS computations are reported for a risk-reduction configuration to demonstrate critical variation among turbulence model results for a given afterbody, ranging from barely-attached to mild separated flow. The effects of body nose geometry and tunnel-wall boundary condition on the computed afterbody flow are explored to inform the design of an experimental test program.

Disotell, Kevin J.↗

Pseudo-direct solution to the boundary-layer equations for separated flow

This paper describes a procedure for the automatic iteration of an inverse boundary-layer technique to a prescribed pressure distribution in a separated flow. The technique is demonstrated by computation of two transonic airfoil flows and two externally generated shock boundary-layer interaction flows. These results are compared to experimental data and to solutions of the full Navier-Stokes equations. These comparisons indicate that substantial economies can be obtained by applying methods like the present, in lieu of full Navier-Stokes methods, in zonal calculation schemes for design purposes. The optimization technique leading to convergence is described in detail and a table of typical computation time is presented.

Arieli, R.↗

Flow Separation from Rods Ahead of Blunt Noses at Mach Number 2.72

An experimental investigation in the Langley Gas Dynamics Laboratory has been made of the flow separation from slender rods mounted to extend forward along the axes of symmetry of blunt-nosed bodies. The mechanism of the separation and its governing criteria are discussed. Drag data at a Mach number of 2.72 for various rod lengths and nose radii at an angle of attack of zero degrees are presented. It was found that the drag coefficients of blunt noses could be appreciably reduced by the use of protruding rods. Criteria for rod length which gives lowest drag are given. (author)

Jones, Jim J↗

Heat Transfer from a Hemisphere-cylinder Equipped with Flow-separation Spikes

Average heat-transfer, temperature-recovery, and pressure-distribution measurements were obtained over the hemispherical nose of a body of revolution both with and without flow-separation spikes. The tests, conducted in a range of Reynolds numbers from 1.55 to 9.85 x 10(5) and from Mach number 0.12 to 5.04, indicated that in supersonic flow the addition of spikes approximately doubles the rate of heat transfer, regardless of spike length.

Stalder, Jackson R↗

Control of separated flow past a cylinder using tangential wall jet blowing

A theoretical analysis is conducted to study the effect of a tangential wall jet on the control of two dimensional separated flow past a circular cylinder. For a tangential wall jet, the mathematical model derived previously is used and the vortex cloud method is adopted for the calculation of the external flow field. For certain limiting cases, the governing equations are simplified and closed forms of solutions for the wall jet parameters can be obtained. It is observed that the wall jet is very efficient in reducing drag by delaying the separation point in the range of small blowing strength. The suction force induced by the wall jet is negligible to the drag due to the external stream. However this suction increases the drag when the blowing strength is large.

Oh, Sejong↗

Turbulent separated flow past a backward-facing step: A critical evaluation of two-equation turbulence models

The ability of two-equation models to accurately predict separated flows is analyzed from a combined theoretical and computational standpoint. Turbulent flow past a backward facing step is chosen as a test case in an effort to resolve the variety of conflicting results that were published during the past decade concerning the performance of two-equation models. It is found that the errors in the reported predictions of the k-epsilon model have two major origins: (1) numerical problems arising from inadequate resolution, and (2) inaccurate predictions for normal Reynolds stress differences arising from the use of an isotropic eddy viscosity. Inadequacies in near wall modelling play a substantially smaller role. Detailed calculations are presented which strongly indicate the standard k-epsilon model - when modified with an independently calibrated anisotropic eddy viscosity - can yield surprisingly good predictions for the backstep problem.

Thangam, S.↗

Application of Navier-Stokes code PAB3D with kappa-epsilon turbulence model to attached and separated flows

A three-dimensional Navier-Stokes solver was used to determine how accurately computations can predict local and average skin friction coefficients for attached and separated flows for simple experimental geometries. Algebraic and transport equation closures were used to model turbulence. To simulate anisotropic turbulence, the standard two-equation turbulence model was modified by adding nonlinear terms. The effects of both grid density and the turbulence model on the computed flow fields were also investigated and compared with available experimental data for subsonic and supersonic free-stream conditions.

Abdol-Hamid, Khaled S.↗

Jet-Pylon Interaction of High Bypass Ratio Separate Flow Nozzle Configurations

NASA Langley Research Center, Hampton, Virginia, 23681-0001 USA An experimental investigation was performed of the acoustic effects of jet-pylon interaction for separate flow and chevron nozzles of both bypass ratio five and eight. The models corresponded to an approximate scale factor of nine. Cycle conditions from approach to takeoff were tested at wind tunnel free jet Mach numbers of 0.1, 0.2 and 0.28. An eight-chevron core nozzle, a sixteen chevron fan nozzle, and a pylon were primary configuration variables. In addition, two orientations of the chevrons relative to each other and to the pylon were tested. The effect of the pylon on the azimuthal directivity was investigated for the baseline nozzles and the chevron nozzles. For the bypass ratio five configuration, the addition of the pylon reduces the noise by approximately 1 EPNdB compared to the baseline case and there is little effect of azimuthal angle. The core chevron produced a 1.8 EPNdB reduction compared to the baseline nozzle. Adding a pylon to the chevron core nozzle produces an effect that depends on the orientation of the chevron relative to the pylon. The azimuthal directivity variation remains low at less than 0.5 EPNdB. For the bypass ratio eight configuration the effect of adding a pylon to the baseline nozzle is to slightly increase the noise at higher cycle points and for the case with a core chevron the pylon has little additional effect. The azimuthal angle effect continues to be very small for the bypass ratio eight configurations. A general impact of the pylon was observed for both fan and core chevrons at both bypass ratios. The pylon reduces the typical low frequency benefit of the chevrons, even eliminating it in some cases, while not impacting the high frequency. On an equal ideal thrust basis, the bypass ratio eight baseline nozzle was about 5 EPNdB lower than the bypass ratio five baseline nozzle at the highest cycle condition, however, with a pylon installed the difference decreased to about 4 EPNdB.

Thomas, Russell H.↗

Analysis of an RNG based turbulence model for separated flows

A two-equation turbulence model of the K-epsilon type was recently derived by using Renormalization Group (RNG) methods. It was later reported that this RNG based model yields substantially better predictions than the standard K-epsilon model for turbulent flow over a backward facing step - a standard test case used to benchmark the performance of turbulence models in separated flows. The improvements obtained from the RNG K-epsilon model were attributed to the better treatment of near wall turbulence effects. In contrast to these earlier claims, it is shown in this paper that the original version of the RNG K-epsilon model substantially underpredicts the reattachment point in the backstep problem. This is a deficiency that is traced to the modeling of the production of dissipation term. However, with the most recent improvements in the RNG K-epsilon model, excellent results for the backstep problem are now obtained.

Speziale, C. G.↗

Model-Invariant Hybrid LES-RANS Computation of Separated Flow Past Periodic Hills

The requirement that physical quantities not vary with a hybrid LESRANS model's blending parameter imposes conditions on the computation that lead to better results across LES-RANS transitions. This promises to allow placement of those transitions so that LES is performed only where required by the physics, improving computational efficiency. The approach is applied to separated flow past periodic hills, where good predictions of separation-bubble size are seen due to the gradual, controlled, LES-RANS transition and the resulting enhanced near-wall eddy viscosity.

Woodruff, Stephen↗

LaRC Separate Flow Testing Status

The main goal of this presentation is to give some of the objectives of the testing program. This includes: develop jet noise data base for separate flow nozzles with bypass ratio's 5 to 14; evaluate effect of pylon on noise; develop low performance impact noise suppression concepts; and evaluate potential for active control of jet noise.

Seiner, Jack↗

Analysis of Extensive Cross-Flow Separation using Higher-Order RANS Closure Models

The turbulent flow fields associated with the incompressible flow over a 6:1 prolate spheroid at high angle of attack, and the supersonic flow over an ogive cylinder are studied. Both these flows are characterized by large separation and vortical flow regions and therefore provide a challenging database for comparison of turbulent closure models. Of interest is the ability to predict the effects of separation and associated vortical motion common to both flows. Two turbulent models are investigated that each represent the class of linear eddy-viscosity models (LEVMs) and explicit algebraic stress models (EASMs). Since the EASM accounts for anisotropic effects, the in- fluence of these effects on flow field predictions can be assessed. The EASM model is shown to both improve the separation location prediction and pressure trough under the secondary vortex on the 6:1 prolate spheroid at high angle of attack and high Reynolds number, and improve the prediction of the separation location on a supersonic ogive cylinder.

Morison, J. H.↗

Analysis of Extensive Cross-Flow Separation using Higher-Order RANS Closure Models

The turbulent flow fields associated with the incompressible flow over a 6:1 prolate spheroid at high angle of attack, and the supersonic flow over an ogive cylinder are studied. Both these flows are characterized by large separation and vortical flow regions and therefore provide a challenging database for comparison of turbulent closure models. Of interest is the ability to predict the effects of separation and associated vortical motion common to both flows. Two turbulent models are investigated that each represent the class of linear eddy-viscosity models (LEVMs) and explicit algebraic stress models (EASMs). Since the EASM accounts for anisotropic effects, the influence of these effects on flow field predictions can be assessed. The EASM model is shown to both improve the separation location prediction and pressure trough under the secondary vortex on the 6:l prolate spheroid at high angle of attack and high Reynolds number, and improve the prediction of the separation location on a supersonic ogive cylinder.

Morrison, J. H.↗

Viscid-inviscid interaction of incompressible separated flows

A flow model has been devised to deal with the viscid-inviscid interaction of a class of two-dimensional incompressible separated flow problems. It is suggested that the corresponding inviscid flow of these problems is described by the free streamline theory with few unspecified parameters and their values are, in turn, determined by the viscous flow considerations. The problem of a flow past a backward facing step is selected for study in detail. The viscous flow components of turbulent jet mixing, recompression, and reattachment are delineated and studied individually. When they are later combined, it is found that the point of reattachment behaves as a saddle-point-type singularity in the system of differential equations describing the viscous flow process. This feature is employed to the determination of the aforementioned free parameters and thus the establishment of the overall corresponding inviscid flow field. The resulting base pressure coefficient for the specific case agrees reasonably well with the available experimental data.

Chow, W. L.↗

Scale effects on turbulent boundary layer development and flow separation around V/STOL inlets at high incidence

Numerical methods for calculating laminar and turbulent boundary layers development around V/STOL engine inlets at high incidence angles, along with the procedures for predicting flow separation, are presented. Results of scale-effects, which are obtained by a numerical scaling procedure on the boundary layer characteristics and incidence angles at onset of separation are discussed. The interesting 'cross-over' phenomena, where the full-scale models actually exhibit earlier separation than the scaled-models, is illustrated for a typical V/STOL inlet at a certain operating condition. Some of the numerical results are compared with the existing wind-tunnel test data for a 1/6 scale inlet model to demonstrate the validity of the numerical approach.

Chou, D. C.↗

A comparative study of Full Navier-Stokes and Reduced Navier-Stokes analyses for separating flows within a diffusing inlet S-duct

A three-dimensional implicit Full Navier-Stokes (FNS) analysis and a 3D Reduced Navier Stokes (RNS) initial value space marching solution technique has been applied to a class of separated flow problems within a diffusing S-duct configuration characterized by vortex-liftoff. Both the FNS and the RNS solution technique were able to capture the overall flow physics of vortex lift-off, and gave remarkably similar results which agreed reasonably well with the experimental measured averaged performance parameters of engine face total pressure recovery and distortion. However, the Full Navier-Stokes and Reduced Navier-Stokes also consistently predicted separation further downstream in the M2129 inlet S-duct than was indicated by experimental data, thus compensating errors were present in the two Navier-Stokes analyses. The difficulties encountered in the Navier-Stokes separations analyses of the M2129 inlet S-duct center primarily on turbulence model issues, and these focused on two distinct but different phenomena, namely, (1) characterization of low skin friction adverse pressure gradient flows, and (2) description of the near wall behavior of flows characterized by vortex lift-off.

Anderson, B. H.↗