Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shock Tube”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Flat plate heat transfer for laminar transition and turbulent boundary layers using a shock tube

Heat transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.12 with gas temperatures of 425 K and 1000 K over a flat plate at room temperature. The measurements were made in air for a Reynolds number range of 600 to 6 million. The heat transfer measurements were conducted in a 70-ft long, 4 in. diameter shock tube. Reflecting wedges were used to reflect the incident shock wave to produce a flow Mach number of 0.12 behind the reflected shock wave. Thin film platinum heat gages were mounted on the plate surface to measure the local heat flux. The laminar results for gas temperatures of 425 K to 1000 K agree well with theory. The turbulent results are also close to incompressible theory, with the 1000 K flow case being slightly higher. The transition results lie between the laminar and turbulent predictions.

Brostmeyer, J. D.↗
NASA NTRS1975

Shock tube study of ionization rates of NaCl-contaminated argon

Electron density, electron temperature, and concentration of excited sodium atoms are measured in the weakly ionized regime behind a shock wave in impure argon in a shock tube using microwave techniques and spectrally resolved radiometry. Evidence is presented to show that an apparent increase in the rate of ionization is due to electron detachment of negative chlorine ions produced from sodium chloride vapor contained as an impurity. To be consistent with this chemical model, rate coefficients are found in the temperature range between 5500 and 8600 K for the dissociation of NaCl into an ion pair, dissociation of NaCl into a neutral pair, and electron detachment of a negative chlorine ion. Electron temperature is lower than heavy-particle temperature by roughly 1000 K. The electron-argon impact-ionization rate coefficient is a weak function of electron temperature in contradiction to expectation.

Schneider, K.-P.↗
NASA NTRS1986

Shock-tube pyrolysis of acetylene - Sensitivity analysis of the reaction mechanism for soot formation

The impact of thermodynamic parameters on the sensitivity of model predictions of soot formation by shock-tube pyrolysis of acetylene were assessed analytically. The pyrolysis process was treated as having three components: initiation, the initial pyrolysis stages; cyclization, formation of larger molecules and radicals and small aromatic molecules; and polymerization, further growth of aromatic rings. Rate equations are reviewed for each component. Thermodynamic effects were assessed by varying the C2H-H and C2H3-H bond energies and the Ct-(Ct) group additivity value. Any change in the C2H-H bond energy had a significant impact on the temperature and the maximum amount of the soot yield. The findings underscore the necessity of using accurate thermodynamic data for modeling high-temperature chemical kinetics.

Frenklach, M.↗
NASA NTRS1961

A Nonlinear Theory for Predicting the Effects of Unsteady Laminar, Turbulent, or Transitional Boundary Layers on the Attenuation of Shock Waves in a Shock Tube with Experimental Comparison

The linearized attenuation theory of NACA Technical Note 3375 is modified in the following manner: (a) an unsteady compressible local skin-friction coefficient is employed rather than the equivalent steady-flow incompressible coefficient; (b) a nonlinear approach is used to permit application of the theory to large attenuations; and (c) transition effects are considered. Curves are presented for predicting attenuation for a shock pressure ratio up to 20 and a range of shock-tube Reynolds numbers. Comparison of theory and experimental data for shock-wave strengths between 1.5 and 10 over a wide range of Reynolds numbers shows good agreement with the nonlinear theory evaluated for a transition Reynolds number of 2.5 X 10(exp 5).

Trimpi, Robert L.↗
NASA NTRS1992

NASA Ames's electric arc-driven shock tube facility and research on nonequilibrium phenomena in low density hypersonic flows

Basic requirements for a ground test facility simulating low density hypersonic flows are discussed. Such facilities should be able to produce shock velocities in the range of 10-17 km/sec in an initial pressure of 0.010 to 0.050 Torr. The facility should be equipped with diagnostics systems to be able to measure the emitted radiation, characteristic temperatures and populations in various energy levels. In the light of these requirements, NASA Ames's electric arc-driven low density shock tube facility is described and available experimental diagnostics systems and computational tools are discussed.

Sharma, Surendra P.↗
NASA NTRS1982

Homogeneous nucleation of ethanol and n-propanol in a shock tube

The condensation by homogeneous nucleation of ethanol (200 proof) and of n-propanol (99.98%) carried at small mole fraction in dry air (99.995%) was studied in the unsteady, isentropic expansion of a shock tube. Samples of the vapor at different partial pressures in dry air at room temperature were expanded into the liquid coexistence regime of the condensing species. A Kristler pressure transducer and Rayleigh light scattering were used to measure the pressure in the expansion and the onset of condensation. Condensation was observed at different locations between 0.15 and 1 m upstream of the diaphragm location, which correspond to different cooling rates of of the vapor samples about 50 to 10 C/ms.

Peters, F.↗
NASA NTRS1974

Shock-tube study of carbon monoxide dissociation kinetics

Carbon monoxide dissociation-rate data were obtained over the temperature range 5600-12,000 K. The experiments were conducted with undiluted CO to emphasize rate constants applicable to molecular gas systems. Data were obtained as time-resolved pressure measurements on the end wall of a shock tube and, in some cases, as emission histories of the C2 Swan system (0-0 band) behind incident shock waves. Results confirm the presence of C2 as an intermediate species in CO decomposition.

Hanson, R. K.↗
NASA NTRS1985

NASTRAN Analysis Comparison to Shock Tube Tests Used to Simulate Nuclear Overpressures

This report presents a study of the effectiveness of the NASTRAN computer code for predicting structural response to nuclear blast overpressures. NASTRAN's effectiveness is determined by comparing results against shock tube tests used to simulate nuclear overpressures. Seven panels of various configurations are compared in this study. Panel deflections are the criteria used to measure NASTRAN's effectiveness. This study is a result of needed improvements in the survivability/vulnerability analyses subjected to nuclear blast.

Wheless, T. K.↗
NASA NTRSDate not supplied

Shock Tube Characterization of Laser Absorption Sensors for Combustion Measurements of Green Propellants

Chemical kinetic models for green spacecraft propulsion systems are needed to calculate efficiency, estimate toxic products, and mitigate plume impingement risks. Laser absorption spectroscopy (LAS) is a common technique used to measure time-resolved mole fraction for model validation. LAS was used to measure species-time history nitrous oxide (N2O) and carbon monoxide (CO) behind reflected shock waves. The diagnostics were implemented at the University of Central Florida high-pressure shock tube facility. A mixture of ethylene (0.002) and N2O (0.008) was diluted with argon gas (0.99) and shock heated 12 bar and temperatures from 1400 to 1600 K.

Marley A. Albright↗
NASA NTRS1975

Shock tube study of ionization rates of NaCl-contaminated argon

Spectrally resolved radiometry and a microwave technique were used to measure the electron density, electron temperature, and concentration, and the concentration of sodium atoms in the weakly ionized region behind a shock wave in an argon shock tube. It is shown that the observed increase in the ionization rate is due to electron detachment of negative chlorine ions produced from sodium chloride vapor contained as an impurity in the argon gas. The observed behavior of the electron temperature in time and the reactions controlled by the electron temperature are analyzed in the light of the impurity reaction scheme.

Scheneider, C.-P.↗
NASA NTRS2022

An Investigation Into Some Important Aspects of Droplet Breakup/Vaporization Behavior Caused By a Gas Flow (Both Nonreacting & Detonative Combustion) in a Shock Tube

As a part of the rotating detonation engine (RDE) technology enablement project at NASA Glenn Research Center (GRC), an effort was undertaken to extend our current computational capabilities of OpenNCC in some important ways with the implementation of a modeling approach to account for the droplet breakup caused by a shock-induced gas motion, & a vaporization model valid over a wide range of pressure conditions encountered in multiphase detonation. With the modified code, a study was undertaken to investigate the individual droplet behavior followed by the passage of a shock front. The study is carried out by tracking a sparse group of droplets to gain some understanding of shock induced droplet behavior under various shock strengths & fuel injector conditions. The study also looks into the effect of randomization involved in determining the droplet breakup outcomes. Over a wide range of sub-critical conditions examined, larger droplets are observed to undergo significant changes in droplet behavior following their breakup. However, smaller droplets (10 µm or less ) remain unaffected by any shock induced breakup. In a follow-on work, we investigated the impact of shock and droplet interaction in a detonation study involving both gaseous as well as gas/liquid (droplet clouds) fuel/air stoichiometric mixtures in a simple 3D shock-tube configuration. The droplet clouds are made up of different initial droplet sizes of either 6, 10, or 30 µm. We also investigated the individual droplet behavior followed by the passage of a detonation front. The results represent conditions that lead to both overdriven and C-J (ChapmanJouguet) detonations. Under both test conditions, most of the droplet vaporization is completed within a short distance (duration) behind the detonation front & well within the region of complete combustion observed in a corresponding equivalent gas-phase fuel/air mixture. The impact of the shock-induced droplet breakup is found to be significant in the calculations involving the 30-µm droplets. Subsequent to the breakup, the drop sizes vary from 1 to 10 µm. Another factor that contributed to the observed rapid vaporization is the result of vaporization taking place under supercritical conditions. The overall detonation properties of various droplet clouds (made up of different initial sizes) are similar to those observed in a corresponding gaseous fuel/air mixture. In the calculation involving a gaseous fuel, the calculated C-J detonation velocity is 1822 m/s involving Jet-A/air and φ = 1. In the overdriven detonation, it is 2044 m/s. In the calculations involving droplet clouds, the corresponding detonation velocities are lower. The impact of increased droplet size is primarily seen in a higher reduction in the detonation velocity.

shock/droplet interaction↗
NASA NTRS1992

Research activity at the shock tube facility at NASA Ames

The real gas phenomena dominate the relaxation process occurring in the flow around hypersonic vehicles. The air flow around these vehicles undergoes vibrational excitation, chemical dissociation, and ionization. These chemical and kinetic phenomena absorb energy, change compressibility, cause temperature to fall, and density to rise. In high-altitude, low density environments, the characteristic thicknesses of the shock layers can be smaller than the relaxation distances required for the gas to attain chemical and thermodynamic equilibrium. To determine the effects of chemical nonequilibrium over a realistic hypersonic vehicle, it would be desirable to conduct an experiment in which all aspects of fluid flow are simulated. Such an experiment is extremely difficult to setup. The only practical alternative is to develop a theoretical model of the phenomena and to compute the flow around the vehicle including the chemical nonequilibrium, and compare the results with the experiments conducted in the facilities under conditions where only a portion of the flow phenomena is simulated. Three types of experimental data are needed to assist the aerospace community in this model development process: (1) data which will enhance our phenomenological understanding of the relaxation process, (2) data on rate reactions for the relevant reactions, and (3) data on bulk properties, such as spectral radiation emitted by the gas, for a given set of aerodynamic conditions. NASA Ames is in a process of collecting such data by simulating the required aerothermochemical conditions in an electric arc driven shock tube.

Sharma, Surendra P.↗
NASA NTRS1983

Shock Tube Studies of Soot Formation

The objective of this research is to record the time histories of the major and minor species which appear in the pyrolysis of toluene, benzene, butadiene, allene, and acetylene; to develop a set of reactions that will model the observed profiles over a wide temperature and concentration range; to identify the critical reactions that influence the pre-particle soot formation process. Toluene and benzene were chosen as two key aromatic compounds which are representative of the pyrolytic process. Butadiene, allene, and acetylene were selected to investigate the formation of aromatic compounds from non-cyclic species. The experimental apparatus used for the study consists of a shock tube coupled to a time-of-flight mass spectrometer Spectra are recorded at 30 microsecond intervals for a total observation time of 0.50 - 1.20 milliseconds. Peak heights of the species of interest in the m/e range 12-300 are measured as a function of reaction time. Calibration curves are constructed which aid the conversion of peak heights to concentrations. The mixtures range from 1 percent-6 percent fuel; the balance is neon diluent.

R D Kern↗
NASA NTRS1985

A high-precision finite element method for shock-tube calculations

A two-pass explicit scheme is developed in order to exploit some of the capabilities of finite difference modeling (FDM) for finite element modeling (FEM), which offers the opportunity to account for any type of geometry in fluid flow modeling. Features of the first-order upwind and the Lax-Wendroff high precision explicit finite difference algorithms are reviewed. A flux limiter is developed for FEM to serve as an analog for the single limiter function which has been defined for the various FDMs. It is shown that an antidiffusive limiter must be introduced into the weighting function which normally multiplies the time-derivative term in the variational equation. The two-pass scheme which results is demonstrated to be the equivalent of FDMs with five-point support. However, the present scheme is valid only for one-dimensional calculations and linear shape functions for shock tube flow phenomena. Further work is required for its use with nonlinear hyperbolic systems.

Hughes, T. J. R.↗
NASA NTRS1988

Shock tube investigation of dynamic response of pressure transducers for validation of rotor performance measurements

For some time now, NASA has had a program under way to aid in the validation of rotor performance and acoustics codes associated with the UH-60 rotary-wing aircraft; and to correlate results of such studies with those obtained from investigations of other selected aircraft rotor performance. A central feature of these studies concerns the dynamic measurement of surface pressure at various locations up to frequencies of 25 KHz. For this purpose, fast-response gauges of the Kulite type are employed. The latter need to be buried in the rotor; they record surface pressures which are transmitted by a pipette connected to the gauge. The other end of the pipette is cut flush with the surface. In certain locations, the pipette configuration includes a rather sharp right-angle bend. The natural question has arisen in this connection: In what way are the pipettes modifying the signals received at the rotor surface and subsequently transmitted to the sensitive Kulite transducer element. The basic details and results of the program performed and recently completed in the High Pressure Shock Tube Laboratory of the Department of Aeronautics and Astronautics at Stanford University are given.

Bershader, Daniel↗