Search NASA⌕ Search

SEARCH · Search NASA

Results for “Static pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Potential uses of vacuum bubbles in noise and vibration control

Vacuum bubbles are new acoustic elements which are dynamically more compliant than the gas volume they replace, but which are statically robust. They are made of a thin metallic shell with vacuum in their cavity. Consequently, they pose no danger in terms of contamination or fire hazard. The potential of the vacuum bubble concept for noise and vibration control was assessed with special emphases on spacecraft and aircraft applications. The following potential uses were identified: (1) as a cladding, to reduce sound radiation of vibrating surfaces and the sound excitation of structures, (2) as a screen, to reflect or absorb an incident sound wave, and (3) as a liner, to increase low frequency sound transmission loss of double walls and to increase the low frequency sound attenuation of muffler baffles. It was found that geometric and material parameters must be controlled to a very high accuracy to obtain optimal performance and that performance is highly sensitive to variations in static pressure. Consequently, it was concluded that vacuum bubbles have more potential in spacecraft applications where static pressure is controlled more than in aircraft applications where large fluctuations in static pressure are common.

Ver, Istvan L.↗
NASA NTRS1950

Effect of Ram-jet Pressure Pulsations on Supersonic-diffuser Performance

Experimental study of effects of combustion roughness and controlled mechanical oscillations on diffuser operation was conducted on an 8-inch ram jet at Mach number 1.87. Within experimental accuracy, the optimum mean combustion-chamber static pressure occurred when the maximum instantaneous static pressure equalled the optimum steady-flow value and the corresponding decrement in optimum mean static pressure was equal to one-half the total amplitude of the pressure pulsations. A marked attenuation of amplitude of cold-buzz pressure fluctuations was effected over limited range of subcritical diffuser operation by means of properly tuned rotating disk located in combustion chamber.

Connors, James F↗
NASA NTRS2003

Mechanisms of Rotating Instability in Axial Compressors Investigated

Rotating instability is a phenomenon that occurs in the tip flow region of axial compressor stages during stable operation. It can be observed in highly staggered rotors with significant tip clearance and is strongest at high-load operating points where the characteristic levels off. In this condition, the single-stage fan under investigation radiates an audible, whistling tone, and wall pressure spectra in the vicinity of the rotor disk exhibit nonrotational components. The graph shows the spectrum of static pressure at a point on the endwall near the leading edge. A hump appears at roughly half of the blade passing frequency (BPF) and is characteristic of rotating instability. A computational model was developed at the NASA Glenn Research Center to investigate the mechanism behind this phenomenon. A three-dimensional steady Navier-Stokes code that has been successfully tested for a wide range of turbomachinery flows was modified to execute a time-accurate simulation of the full annulus of the compressor. At the inlet of the computational domain, the total pressure, total temperature, and two velocity components are specified. Since no unsteady measurements of static pressure or other flow variables were available downstream of the rotor, circumferentially averaged static pressure was specified on the shroud at the outlet of the computational domain. A three-dimensional view of the vortex from the numerical model is shown. Particle traces released near the leading edge tip have rolled up to illustrate the tip clearance vortex. Flow near the trailing edge is pushed forward by the axially reversed flow. It then interacts with the tip clearance flow and the incoming flow and results in the rotating instability vortex, the core of which is illustrated by total pressure shading on planes located successively downstream. The rotating instability vortex is formed periodically midway between the blades and moves toward the pressure side of the passage. The unsteady behavior of this vortex structure is the main mechanism of the rotating instability is shown. The numerical model can be used to detect any possible occurrence of rotating instability when the tip clearance increases during engine service.

Hah, Chunill↗
NASA NTRS1972

Basic flow characteristics of a linear aerospike nozzle segment.

The separated base flow region within a linear aerospike nozzle segment is investigated experimentally in an ejector-diffuser system. The nozzle-diffuser system and base pressure characteristics are described over the pressure ratio range from the 'open wake' to the 'closed wake' operation. Schlieren photographs and static pressure distributions along the test section centerline and top contour describe the transition from 'open wake' to 'closed wake' flow fields. Base pressure and static pressure distributions are utilized to present the effects of a ramp diffuser. The effects of base bleed on the base pressure ratio and structure of the nozzle flow field are also presented.

Mueller, T. J.↗
NASA NTRS2012

Effect of Sweep on Cavity Flow Fields at Subsonic and Transonic Speeds

An experimental investigation was conducted in the NASA Langley 7 x 10-Foot High Speed Tunnel (HST) to study the effect of leading- and trailing-edge sweep on cavity flow fields for a range of cavity length-to-height (l/h) ratios. The free-stream Mach number was varied from 0.2 to 0.8. The cavity had a depth of 0.5 inches, a width of 2.5 inches, and a maximum length of 12.0 inches. The leading- and trailing-edge sweep was adjusted using block inserts to achieve leading edge sweep angles of 65 deg, 55 deg, 45 deg, 35 deg, and 0 deg. The fore and aft cavity walls were always parallel. The aft wall of the cavity was remotely positioned to achieve a range of length-to-depth ratios. Fluctuating- and static-pressure data were obtained on the floor of the cavity. The fluctuating pressure data were used to determine whether or not resonance occurred in the cavity rather than to provide a characterization of the fluctuating pressure field. Qualitative surface flow visualization was obtained using a technique in which colored water was introduced into the model through static-pressure orifices. A complete tabulation of the mean static-pressure data for the swept leading edge cavities is included.

Tracy, Maureen B.↗
NASA NTRS1993

Forcing function modeling for flow induced vibration

The fundamental forcing function unsteady aerodynamics for application to turbomachine blade row forced response are considered, accomplished through a series of experiments performed in a rotating annular cascade and a research axial flow turbine. In particular, the unsteady periodic flowfields downstream of rotating rows of perforated plates, airfoils and turbine blade rows are measured with a cross hot-wire and an unsteady total pressure probe. The unsteady velocity and static pressure fields were then analyzed harmonically and split into vortical and potential gusts, accomplished by developing a gust splitting analysis which includes both gust unsteady static pressure and velocity data. The perforated plate gusts closely were found to be linear theory vortical gusts, satisfying the vortical gust constraints. The airfoil and turbine blade row generated velocity perturbations did not satisfy the vortical gust constraints. However, the decomposition of the unsteady flow field separated the data into a propagating vortical component which satisfied these vortical gust constraints and a decaying potential component.

Fleeter, Sanford↗
NASA NTRS1950

The Effect of the Inlet Mach Number and Inlet-boundary-layer Thickness on the Performance of a 23 Degree Conical-diffuser-tail-pipe Combination

An investigation was conducted to determine the effect of the inlet Mach number and entrance-boundary-layer thickness on the performance of a 23 degree 21-inch conical-diffuser - tail-pipe combination with a 2:1 area ratio. The air flows used in this investigation covered an inlet Mach number range from 0.17 to 0.89 and corresponding Reynolds numbers of 1,700,000 to 7,070,000. Results are reported for two inlet-boundary-layer thicknesses. Over the entire range of flows, the mean value of the inlet displacement thickness is about 0.034 inch for the thinner inlet boundary layer and about 0.170 inch for the case of the thicker inlet boundary layer. The performance of the diffuser - tail-pipe combination is presented together with examples of longitudinal static-pressure distribution and the results of boundary-layer pressure surveys made at six points along the diffuser wall. The results indicated a progressive diminution of the static-pressure recovery and a steady increase in the total-pressure losses as the inlet Mach number was increased for both inlet-boundary-layer thicknesses. The ratio of actual static-pressure rise to that theoretically possible was much less and the total-pressure losses were greater for the case of the thicker inlet boundary layer throughout the speed range investigated. With the thinner inlet boundary layer, flow separation occurred at the diffuser exit at all inlet Mach numbers.Unseparated flow alternating with separated flow was observed near the inlet at the higher velocities. For the case of the thicker inlet boundary layer, the origin of the separated region occurred in the vicinity of the inlet-duct-diffuser junction section at all Mach numbers.

Persh, Jerome↗
NASA NTRS1983

End wall flow characteristics and overall performance of an axial flow compressor stage

This review indicates the possible future directions for research on endwall flows in axial flow compressors. Theoretical investigations on the rotor blade endwall flows in axial flow compressors reported here include the secondary flow calculation and the development of the momentum integral equations for the prediction of the annulus wall boundary layer. The equations for secondary vorticity at the rotor exit are solved analytically. The solution includes the effects of rotation and the viscosity. The momentum integral equations derived include the effect of the blade boundary layers. The axial flow compressor facility of the Department of Aerospace Engineering at The Pennsylvania State University, which is used for the experimental investigations of the endwall flows, is described in some detail. The overall performance and other preliminary experimental results are presented. Extensive radial flow surveys are carried out at the design and various off design conditions. These are presented and interpreted in this report. The following experimental investigations of the blade endwall flows are carried out. (1) Rotor blade endwall flows: The following measurements are carried out at four flow coefficients. (a) The rotor blade static pressures at various axial and radial stations (with special emphasis near the blade tips). (b) The hub wall static pressures inside the rotor blade passage at various axial and tangential stations. (2) IGV endwall flows: The following measurements are carried out at the design flow coefficient. (a) The boundary layer profiles at various axial and tangential stations inside the blade passage and at the blade exit. (b) Casing static pressures and limiting streamline angles inside the blade passage.

Sitaram, N.↗
NASA NTRS1973

Two-dimensional cascade test of a highly loaded, low-solidity, tandem airfoil turbine rotor blade

A tip region section of a low-solidity tandem airfoil blade for a turbine rotor was tested in a two-dimensional cascade tunnel at solidities of 0.736 and 0.912. Blade surface static pressures and blade exit total and static pressure and flow angle were surveyed. Blade surface velocities, wake shapes, and kinetic energy losses were analyzed and compared with values for 1.852 solidity tandem airfoil blading.

Kline, J. F.↗
NASA NTRS1991

Progress toward synergistic hypermixing nozzles

Mean flow measurements were obtained for air-to-air mixing downstream of swept and unswept ramp wall mounted hypermixing nozzle configurations. Aside from the sweep of the ramps, the two nozzle configurations studied are identical. The nozzles inject three parallel supersonic jets at a 15 deg angle (relative to the wind tunnel wall) into a supersonic freestream. Mach number and volume fraction distributions in a transverse plane 11.1 nozzle heights downstream from the nozzle exit plane were measured. Data are presented for a freestream Mach number of three at a matched static pressure condition and also at underexpanded static pressure condition (pressure ratio = 5). Surface oil flow visualization was used to study the near wall flow behavior. The results indicate that the swept ramp injectors produce stronger and larger vortex pairs than the unswept ramp injectors. The increased interaction between the swept ramp model's larger vortex pairs yields better mixing characteristics for this model.

Davis, D. O.↗
NASA NTRS1976

Pressure and velocity in a developing coaxial jet

Determinations of static pressure, mean velocity and turbulence intensity in the developing region of coaxial jets are presented. Detailed profiles were obtained at twelve axial locations (extending from the nozzle exit for a distance of 5 diameters) downstream from a single element of the Bell Aerospace H2/O2 19-element coaxial injector. Measurements of mass-flux per unit area (using a constant temperature anemometer), total pressure and local temperature were used in the determination of local static pressure and velocity. These data show a low pressure region exists near the nozzle exit. Although this pressure reduction is small (0.34 psi), it substantially altered the flow development. Comparison of results shows that velocity near the nozzle exit decreases initially (no central velocity core) as a result of both pressure gradients and viscous mixing. These data are compared with analytical predictions made using available computer codes. Results show the need to consider pressure effects in any proposed mathematical model.

Moon, L. F.↗
NASA NTRS1972

Analysis and testing of high entrainment single nozzle jet pumps with variable mixing tubes

An analytical model was developed to predict the performance characteristics of axisymmetric single-nozzle jet pumps with variable area mixing tubes. The primary flow may be subsonic or supersonic. The computer program uses integral techniques to calculate the velocity profiles and the wall static pressures that result from the mixing of the supersonic primary jet and the subsonic secondary flow. An experimental program was conducted to measure mixing tube wall static pressure variations, velocity profiles, and temperature profiles in a variable area mixing tube with a supersonic primary jet. Static pressure variations were measured at four different secondary flow rates. These test results were used to evaluate the analytical model. The analytical results compared well to the experimental data. Therefore, the analysis is believed to be ready for use to relate jet pump performance characteristics to mixing tube design.

Hickman, K. E.↗
NASA NTRS1972

Turbulent boundary layer in an adverse pressure gradient without effect of wall curvature

The hypersonic compressible turbulent boundary layer in an adverse pressure gradient along a cylindrical axisymmetric body was studied. The tests were conducted in a Mach 6 contoured axisymmetric nozzle. An external compression cowl was used to produce the gradual adverse pressure gradient and a maximum pressure rise of 7 times the freestream static pressure was achieved in a test region of 23 cm. Boundary layer profiles of static pressure, total pressure, and total temperature, as well as wall transient heat transfer rates were measured. Comparisons of the velocity total temperature profiles to linear and quadratic relations were made. Measured heat transfer data were in good agreement with the prediction from the flat-plate reference enthalpy method. Integral parameters were also in good agreement with results of numerical solutions for compressible turbulent boundary layer equations.

Zakkay, V.↗
NASA NTRS1981

A program to evaluate a control system based on feedback of aerodynamic pressure differentials. Part 2: Data report for phase 1 wind tunnel test

Wind tunnel test data are presented. The purpose of the test was to determine the sensor location for sensitivity to flap deflection and to determine the range required of the sensor. The calculations followed to correct the raw pressure measurements, the corrected measurements, which represent the static pressures along the airfoil surface, and the static pressures tabulated and in coefficient form are described. However, the chordwise locations of the upper and lower surface taps do not coincide. An interpolation routine is performed to find the lower surface pressure coefficients at the upper surface tap locations. The difference, C sub P(lower) - C sub P(upper), is calculated and listed and the data are reorganized with respect to each tap location. A numerical regression performed to quantify the slopes of the graphs allows more accurate comparison of sensitivity and linearity.

Hrabak, R. R.↗
NASA NTRS1992

Analysis of an advanced ducted propeller subsonic inlet

A time marching Navier-Stokes code called PARC (PARC2D for 2-D/axisymmetric and PARC3D for 3-D flow simulations) was validated for an advanced ducted propeller (ADP) subsonic inlet. The code validation for an advanced ducted propeller (ADP) subsonic inlet. The code validation was implemented for a non-separated flow condition associated with the inlet operating at angles-of-attack of 0 and 25 degrees. The inlet test data were obtained in the 9 x 15 ft Low Speed Wind Tunnel at NASA Lewis Research Center as part of a cooperative study with Pratt and Whitney. The experimental study focused on the ADP inlet performance for take-off and approach conditions. The inlet was tested at a free stream Mach number of 0.2, at angles-of-attack between O and 35 degrees, and at a maximum propeller speed of 12,000 RPM which induced a corrected air flow rate of about 46 lb/sec based on standard day conditions. The computational grid and flow boundary conditions (BC) were based on the actual inlet geometry and the funnel flow conditions. At the propeller face, two types of BC's were applied: a mass flow BC and a fixed flow properties BC. The fixed flow properties BC was based on a combination of data obtained from the experiment and calculations using a potential flow code. Comparison of the computational results with the test data indicates that the PARC code with the propeller face fixed flow properties BC provided a better prediction of the inlet surface static pressures than the predictions when the mass flow BC was used. For an angle-of-attack of 0 degrees, the PARC2D code with the propeller face mass flow BC provided a good prediction of inlet static pressures except in the region of high pressure gradient. With the propeller face fixed flow properties BC, the PARC2D code provided a good prediction of the inlet static pressures. For an angle-of-attack of 25 degrees with the mass flow BC, the PARC3D code predicted statis pressures which deviated significantly from the test data; however, with the fixed flow properties BC, a good comparison with the test data was obtained.

Iek, Chanthy↗
NASA NTRS1991

Turbulent boundary layer separation over a rearward facing ramp and its control through mechanical excitation

A vane which oscillates about a fixed point at the inlet to a two-dimensional, 20-deg rearward-facing ramp has been noted to effectively delay the separation of a turbulent boundary layer. A parametric study has been conducted to determine the variation of the maximum values of the static pressure recovery, measured close to the ramp exit as a function of the oscillation frequency of the vane. The resulting curves show a peak value in the maximum static pressure recovery as a function of the vane's oscillation frequency. For the excited cases, corona anemometer measurements in the inner wall regions of the boundary layer along the surface of the ramp show a large range of unsteadiness in the local velocities. Finally, a qualitative explanation of the phenomena of delay of separation is discussed which appears to be supported by the surface static pressure and flow field measurements obtained.

Mckinzie, Daniel J., Jr.↗
NASA NTRS2005

Experimental Investigation of a Morphing Nacelle Ducted Fan

The application of Circulation Control to the nacelle of a shrouded fan is proposed as a means to enhance off-design performance of the shrouded fan. Typically, a fixed geometry shroud is efficient at a single operating condition. Modifying circulation about the fixed geometry is proposed as a means to virtually morph the shroud without moving surfaces. This approach will enhance off-design-point performance with minimal complexity, weight, and cost. Termed the Morphing Nacelle, this concept provides an attractive propulsion option for Vertical Take-off and Landing (VTOL) aircraft, such conceptual Personal Air Vehicle (PAV) configurations proposed by NASA. An experimental proof of concept investigation of the Morphing Nacelle is detailed in this paper. A powered model shrouded fan model was constructed with Circulation Control (CC) devices integrated in the inlet and exit of the nacelle. Both CC devices consisted of an annular jet slot directing a jet sheet tangent to a curved surface, generally described as a Coanda surface. The model shroud was tailored for axial flight, with a diffusing inlet, but was operated off-design condition as a static lifting fan. Thrust stand experiments were conducted to determine if the CC devices could effectively improve off-design performance of the shrouded fan. Additional tests were conducted to explore the effectiveness of the CC devices a means to reduce peak static pressure on the ground below a lifting fan. Experimental results showed that off-design static thrust performance of the model was improved when the CC devices were employed under certain conditions. The exhaust CC device alone, while effective in diffusing the fan exhaust and improving weight flow into shroud inlet, tended to diminish performance of the fan with increased CC jet momentum. The inlet CC device was effective at reattaching a normally stalled inlet flow condition, proving an effective means of enhancing performance. A more dramatic improvement in static thrust was obtained when the inlet and exit CC devices were operated in unison, but only over a limited range of CC jet momentum. Operating the nacelle inlet and exit CC devices together proved very effective in reducing peak ground plane static pressure, while maintaining static thrust. The Morphing Nacelle concept proved effective at enhancing off-design performance of the model; however, additional investigation is necessary to generalize the results.

Kondor, Shayne A.↗
NASA NTRS2020

Full Aerothermal Characterization of the 6- by 9-Foot Icing Research Tunnel (2019 Test)

A full aerothermal characterization of the NASA Glenn Icing Research Tunnel (IRT) was completed in August 2019. A mandatory maintenance period required the test entry to be separated into two phases: the first occurring in April 2019 and the second in August 2019. The hardware used during this test entry consisted of the 6-foot quick-check rake, 6-foot traversing rake, RTD array, and hot-wire rake. The 6-foot quick check rake collects static pressure, total pressure, total temperature, and flow angularity data along the centerline of the test section. The data from the 6-foot quick-check rake were used to generate test section calibration relationships for total and static pressure as well as implement statistical process control. The 6-foot traversing rake collects flow uniformity data across the test section for various flow parameters, such as static pressure, total pressure, and flow angularity. Total temperature flow uniformity data is mapped by the RTD array and is used to generate the test section calibration relationship for total temperature. The hot-wire rake measures turbulence intensity at three lateral locations and characterizes airspeed unsteadiness in the test section. The test entry resulted in updated calibration relationships and a full characterization of test section flow quality and flow uniformity in the IRT.

Wind↗