Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Experimental stress analysis of large plastic deformations in a hollow sphere deformed by impact against a concrete block

An experimental plastic strain measurement system is presented for use on the surface of high velocity impact test models. The system was used on a hollow sphere tested in impact against a reinforced concrete block. True strains, deviatoric stresses, and true stresses were calculated from experimental measurements. The maximum strain measured in the model was small compared to the true failure strain obtained from static tensile tests of model material. This fact suggests that a much greater impact velocity would be required to cause failure of the model shell structure.

Morris, R. E.↗
NASA NTRS1981

Development of orthotropic birefringent materials for photoelastic stress analysis

Materials were selected and fabrication procedures developed for orthotropic birefringent materials. An epoxy resin (Maraset 658/558 system) was selected as the matrix material. Fibers obtained from style 3733 glass cloth and type 1062 glass roving were used as reinforcement. Two different fabrication procedures were used. In the first one, layers of unidirectional fibers removed from the glass cloth were stacked, impregnated with resin, bagged and cured in the autoclave at an elevated temperature. In the second procedure, the glass roving was drywound over metal frames, impregnated with resin and cured at room temperature under pressure and vacuum in an autoclave. Unidirectional, angle-ply and quasi-isotropic laminates of two thicknesses and with embedded flaws were fabricated. The matrix and the unidirectional glass/epoxy material were fully characterized. The density, fiber volume ratio, mechanical, and optical properties were determined. The fiber volume ratio was over 0.50. Birefringent properties were in good agreement with predictions based on a stress proportioning concept and also, with one exception, with properties predicted by a finite element analysis.

Daniel, I. M.↗
NASA NTRS1991

Stress analysis of Tellus Regio, Venus, based on gravity and topography - Comparison with Venera 15/16 radar images

The tectonics of the Tellus Region highland on Venus is examined using the altimetry and gravity data collected by Pioneer Venus, which were incorporated into a thin elastic shell model to calculate both the global (long-wavelength) and the regional (short-wavelength) stresses for various assumed values of crust, lithosphere, and mantle thickness and modes of compensation. The resultant stress fields were compared to the surface morphology observed in the Venera 15/16 radar images and interpreted in terms of stress history of Tellus Regio. The best fitting parameters were found to be consistent with minor amounts of lithospheric flexure being necessary to produce the observed surface features of this region.

Williams, David R.↗
NASA NTRS1972

Physiological factors and optical parameters as bases of vegetation discrimination and stress analysis.

The successful application of photographic, optical-mechanical scanning, and other sensing techniques to vegetation must be based on an understanding of the biological and physical principles involved. The objective is to review the biological and optical characteristics of vegetation and to discuss how knowledge of them can support operational programs by aiding in wavelength selection, timing of missions, and discriminations between vegetation types as well as between healthy and stressed plants of the same type. Both laboratory situations, in which relatively pure spectral data are obtained, and field situations are considered. In the latter, sensor performance and background variables affect data quality.

Wiegand, C. L.↗
NASA NTRS1992

Stress analysis and damage evaluation of flawed composite laminates by hybrid-numerical methods

Structural components in flight vehicles is often inherited flaws, such as microcracks, voids, holes, and delamination. These defects will degrade structures the same as that due to damages in service, such as impact, corrosion, and erosion. It is very important to know how a structural component can be useful and survive after these flaws and damages. To understand the behavior and limitation of these structural components researchers usually do experimental tests or theoretical analyses on structures with simulated flaws. However, neither approach has been completely successful. As Durelli states that 'Seldom does one method give a complete solution, with the most efficiency'. Examples of this principle is seen in photomechanics which additional strain-gage testing can only average stresses at locations of high concentration. On the other hand, theoretical analyses including numerical analyses are implemented with simplified assumptions which may not reflect actual boundary conditions. Hybrid-Numerical methods which combine photomechanics and numerical analysis have been used to correct this inefficiency since 1950's. But its application is limited until 1970's when modern computer codes became available. In recent years, researchers have enhanced the data obtained from photoelasticity, laser speckle, holography and moire' interferometry for input of finite element analysis on metals. Nevertheless, there is only few of literature being done on composite laminates. Therefore, this research is dedicated to this highly anisotropic material.

Yang, Yii-Ching↗
NASA NTRS1953

Experimental Stress Analysis of Stiffened Cylinders with Cutouts.pure Torsion

Torsion tests were made on a cylindrical semimonocoque shell of circular cross section. The cylinder was first tested without a cutout, and then with a rectangular cutout which was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 to 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each size of cutout, and the stresses obtained are presented in tables. (author)

LOADS AND STRESSES, STRUCTURAL - TORSION↗
NASA NTRS1954

Experimental Stress Analysis of Stiffened Cylinders with Cutouts : Pure Bending

Bending tests were made on a cylindrical semimonocoque shell of circular cross section. The cylinder was tested without a cutout and then with a rectangular cutout which was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 to 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each size of cutout, and the stresses obtained are presented in tables. (author)

Schlechte, Floyd R↗
NASA NTRS1981

Thermal and stress analysis of thermal barrier coatings

An analysis has been performed that predicts the thermomechanical behavior of thermal barrier coated specimens. The analysis predicts the behavior during both plasma spray coating application and burner rig testing conditions simulating engine operation. The analysis was accomplished through utilization of one-dimensional through thickness and two-dimensional finite element calculations. The results of these calculations showed that specimens with a substrate control temperature between 300 F and 600 F would be optimum. Controlling substrate temperature was found to have a more dominant effect on the mechanical strains than the ceramic or substrate thicknesses. The predicted stresses and mechanical strains at the bond-coating interface are large enough to cause cracks in this region where post-test observations have determined coating failures originate.

Cassenti, B. N.↗
NASA NTRS1982

Digital imaging techniques in experimental stress analysis

Digital imaging techniques are utilized as a measure of surface displacement components in laser speckle metrology. An image scanner which is interfaced to a computer records and stores in memory the laser speckle patterns of an object in a reference and deformed configuration. Subsets of the deformed images are numerically correlated with the references as a measure of surface displacements. Discrete values are determined around a closed contour for plane problems which then become input into a boundary integral equation method in order to calculate surface traction in the contour. Stresses are then calculated within this boundary. The solution procedure is illustrated by a numerical example of a case of uniform tension.

Peters, W. H.↗
NASA NTRS1989

Stress analysis method for clearance-fit joints with bearing-bypass loads

Within a multi-fastener joint, fastener holes may be subjected to the combined effects of bearing loads and loads that bypass the hole to be reacted elsewhere in the joint. The analysis of a joint subjected to search combined bearing and bypass loads is complicated by the usual clearance between the hole and the fastener. A simple analysis method for such clearance-fit joints subjected to bearing-bypass loading has been developed in the present study. It uses an inverse formulation with a linear elastic finite-element analysis. Conditions along the bolt-hole contact arc are specified by displacement constraint equations. The present method is simple to apply and can be implemented with most general purpose finite-element programs since it does not use complicated iterative-incremental procedures. The method was used to study the effects of bearing-bypass loading on bolt-hole contact angles and local stresses. In this study, a rigid, frictionless bolt was used with a plate having the properties of a quasi-isotropic graphite/epoxy laminate. Results showed that the contact angle as well as the peak stresses around the hole and their locations were strongly influenced by the ratio of bearing and bypass loads. For single contact, tension and compression bearing-bypass loading had opposite effects on the contact angle. For some compressive bearing-bypass loads, the hole tended to close on the fastener leading to dual contact. It was shown that dual contact reduces the stress concentration at the fastener and would, therefore, increase joint strength in compression. The results illustrate the general importance of accounting for bolt-hole clearance and contact to accurately compute local bolt-hole stresses for combined bearings and bypass loading.

Naik, R. A.↗
NASA NTRS1972

Stress Analysis and Design of Silicon Solar Cell Arrays and Related Material Properties

A systematic approach is presented for the design of solar cell arrays to eliminate mechanical failures that might arise in components of the arrays in a thermal environment. A prerequisite to the approach is the characterization of material properties at different temperatures. Significant data is obtained for the thermal behavior of the silicon solar cell material and adhesives. Upon determining the mechanical and thermal material properties of the components of the solar cell array, utilizing a finite element idealization for predicting the stress fields in the components, and employing the von Mises failure criterion, potential failure areas in various design configurations in a given thermal environment are identified. Guide lines and means to optimize a given design are illustrated by two examples.

Salama, A. M.↗
NASA NTRS1984

Stress analysis of multilayered plates around circular holes

The elasticity problem for a thick plate consisting of two bonded dissimilar homogeneous layers is considered. It is assumed that the plate is infinite, contains a circular hole, and is subjected to axisymmetric external loads. A technique suitable to the formulation of three-dimensional boundary value problems is introduced and applied to the three-dimensional elasticity solution of an infinite plate with a hole. The effect of Poisson's ratio is studied in some detail, and the axisymmetric problem of a laminated plate is solved. The stresses at the interface are calculated and are observed to become unbounded at the hole boundary. An approximate treatment of the singularity is presented and the stress intensity factors are computed. Some of the results are compared with those found from the finite element method. The agreement between the two sets with regard to trend and magnitude is found to be very satisfactory.

Delale, F.↗
NASA NTRS2000

An Assessment of Five Modeling Approaches for Thermo-Mechanical Stress Analysis of Laminated Composite Panels

A study is made of the effects of variation in the lamination and geometric parameters, and boundary conditions of multi-layered composite panels on the accuracy of the detailed response characteristics obtained by five different modeling approaches. The modeling approaches considered include four two-dimensional models, each with five parameters to characterize the deformation in the thickness direction, and a predictor-corrector approach with twelve displacement parameters. The two-dimensional models are first-order shear deformation theory, third-order theory; a theory based on trigonometric variation of the transverse shear stresses through the thickness, and a discrete layer theory. The combination of the following four key elements distinguishes the present study from previous studies reported in the literature: (1) the standard of comparison is taken to be the solutions obtained by using three-dimensional continuum models for each of the individual layers; (2) both mechanical and thermal loadings are considered; (3) boundary conditions other than simply supported edges are considered; and (4) quantities compared include detailed through-the-thickness distributions of transverse shear and transverse normal stresses. Based on the numerical studies conducted, the predictor-corrector approach appears to be the most effective technique for obtaining accurate transverse stresses, and for thermal loading, none of the two-dimensional models is adequate for calculating transverse normal stresses, even when used in conjunction with three-dimensional equilibrium equations.

Noor, A. K.↗
NASA NTRS1946

Stress Analysis of Columns and Beam Columns by the Photoelastic Method

Principles of similarity and other factors in the design of models for photoelastic testing are discussed. Some approximate theoretical equations, useful in the analysis of results obtained from photoelastic tests are derived. Examples of the use of photoelastic techniques and the analysis of results as applied to uniform and tapered beam columns, circular rings, and statically indeterminate frames, are given. It is concluded that this method is an effective tool for the analysis of structures in which column action is present, particularly in tapered beam columns, and in statically indeterminate structures in which the distribution of loads in the structures is influenced by bending moments due to axial loads in one or more members.

BEAM-COLUMNS - STRESSES↗
NASA NTRS1972

Structural dynamic and thermal stress analysis of nuclear reactor vessel support system

A nuclear reactor vessel is supported by a Z-ring and a box ring girder. The two proposed structural configurations to transmit the loads from the Z-ring and the box ring girder to the foundation are shown. The cantilever concrete ledge transmitting the load from the Z-ring and the box girder via the cavity wall to the foundation is shown, along with the loads being transmitted through one of the six steel columns. Both of these two supporting systems were analyzed by using rigid format 9 of NASTRAN for dynamic loads, and the thermal stresses were analyzed by AXISOL. The six column configuration was modeled by a combination of plate and bar elements, and the concrete cantilever ledge configuration was modeled by plate elements. Both configurations were found structurally satisfactory; however, nonstructural considerations favored the concrete cantilever ledge.

Chi-Diango, J.↗
NASA NTRS1954

Experimental Stress Analysis of Stiffened Cylinders with Cutouts : Shear Load

A cylindrical semimonocoque shell of circular cross section was mounted as a cantilever and loaded by a direct shear at the tip. The cylinder was tested with no cutout, with a rectangular cutout on the tension side, and with the cutout centered on the neutral axis on one side of the cylinder. The cutout was successively enlarged through six sizes varying from 30 degrees to 130 degrees in circumference and from 1 and 2 bays in length. Strain measurements were made with resistance-type wire strain gages near the cutout on the stringers, the skin, and the rings for each case, and the stresses obtained are presented in tables. (author)

Rosecrans, Richard↗