SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analysis of normal accelerations through center of gravity of aircraft due to landing impacts and ground operations associated with taxi, takeoff, and landing
The internal performance of two exhaust system concepts applicable to single-engine short-take-off and vertical-landing tactical fighter configurations was investigated. These concepts involved blocking (or partially blocking) tailpipe flow to the rear (cruise) nozzle and diverting it through an opening to a ventral nozzle exit for vertical thrust. A set of variable angle vanes at the ventral nozzle exit were used to vary ventral nozzle thrust angle between 45 and 110 deg relative to the positive axial force direction. In the vertical flight mode the rear nozzle (or tailpipe flow to it) was completely blocked. In the transition flight mode flow in the tailpipe was split between the rear and ventral nozzles and the flow was vectored at both exits for aircraft control purposes through this flight regime. In the cruise flight mode the ventral nozzle was sealed and all flow exited through the rear nozzle.
Present designs for large flying boats are characterized by high wing loading, high aspect ratio, and low parasite drag. The high wing loading results in the universal use of flaps for reducing the takeoff and landing speeds. These factors have an effect on takeoff performance and influence to a certain extent the design of the hull. An investigation was made of the influence of various factors and design parameters on the takeoff performance of a hypothetical large flying boat by means of takeoff calculations. The parameters varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The takeoff times and distances were calculated to the stalling speeds and the performance above these speeds was studied separately to determine piloting technique for optimum takeoff. The advantage of quick deflection of the flap at high water speeds is shown.
Methods for providing runway information in cockpit during aircraft takeoff and landing roll
Objective and subjective data gathered in the processes of comparing a linear and a nonlinear washout for motion simulators reveal that there is no difference in the pilot performance measurements used during instrument landing system (ILS) approaches with a Boeing 737 conventional takeoff and landing (CTOL) airplane between fixed base, linear washout, and nonlinear washout operations. However, the subjective opinions of the pilots reveal an important advance in motion cue presentation. The advance is not in the increased cue available over a linear filter for the same amount of motion base travel but rather in the elimination of false rotational rate cues presented by linear filters.
Electric propulsion enables radical new vehicle concepts, particularly for Vertical Takeoff and Landing (VTOL) aircraft because of their significant mismatch between takeoff and cruise power conditions. However, electric propulsion does not merely provide the ability to normalize the power required across the phases of flight, in the way that automobiles also use hybrid electric technologies. The ability to distribute the thrust across the airframe, without mechanical complexity and with a scale-free propulsion system, is a new degree of freedom for aircraft designers. Electric propulsion is scale-free in terms of being able to achieve highly similar levels of motor power to weight and efficiency across a dramatic scaling range. Applying these combined principles of electric propulsion across a VTOL aircraft permits an improvement in aerodynamic efficiency that is approximately four times the state of the art of conventional helicopter configurations. Helicopters typically achieve a lift to drag ratio (L/D) of between 4 and 5, while the VTOL aircraft designed and developed in this research were designed to achieve an L/D of approximately 20. Fundamentally, the ability to eliminate the problem of advancing and retreating rotor blades is shown, without resorting to unacceptable prior solutions such as tail-sitters. This combination of concept and technology also enables a four times increase in range and endurance while maintaining the full VTOL and hover capability provided by a helicopter. Also important is the ability to achieve low disc-loading for low ground impingement velocities, low noise and hover power minimization (thus reducing energy consumption in VTOL phases). This combination of low noise and electric propulsion (i.e. zero emissions) will produce a much more community-friendly class of vehicles. This research provides a review of the concept brainstorming, configuration aerodynamic and mission analysis, as well as subscale prototype construction and flight testing that verifies transition flight control. A final down-selected vehicle is also presented.
Short takeoff and landing (STOL) performance utilizing a circulation control airfoil was successfully demonstrated on the A-6 CCW (circulation control wing). Controlled flight at speeds as slow as 67 knots was demonstrated. Takeoff ground run and liftoff speed reductions in excess of 40 and 20 percent respectively were achieved. Landing ground roll and approach speeds were similarly reduced. The technology demonstrated was intended to be useable on modern high performance aircraft. STOL performance would be achieved through the combination of a 2-D vectored nozzle and a circulation control type of high lift system. The primary objective of this demonstration was to attain A-6 CCW magnitude reductions in takeoff and landing flight speed and ground distance requirements using practical bleed flow rates from a modern turbofan engine for the blown flap system. Also, cruise performance could not be reduced by the wing high lift system. The A-6 was again selected as the optimum demonstration vehicle. The procedure and findings of the study to select the optimum high lift wing design are documented. Some findings of a supercritical airfoil and a comparison of 2-D and 3-D results are also described.
Current research on vertical- or short-takeoff-and-landing (V/STOL) aircraft is concentrating on developing a multirole-capable fighter. Several V/STOL concepts being studied show a capability performing for short-takeoff and vertical-landing (STOVL) missions. This paper is concerned with a propulsion concept which promises added flexibility in mission performance: the hybrid-tandem fan. This propulsion concept is combined with four aircraft planforms and the performance of each is evaluated on a representative mission. The four aircraft planforms used in the study are a conventional wing-tail, a forward-swept wing and canard, a delta-wing and canard, and an oblique wing and tail. The mission was chosen so that the four aircraft all had approximately the same gross takeoff weight. The four designs are compared at various phases of the mission.
Engine failure represents a major safety concern to helicopter operations, especially in the critical flight phases of takeoff and landing from/to small, confined areas. As a result, the JAA and FAA both certificate a transport helicopter as either Category-A or Category-B according to the ability to continue its operations following engine failures. A Category-B helicopter must be able to land safely in the event of one or all engine failures. There is no requirement, however, for continued flight capability. In contrast, Category-A certification, which applies to multi-engine transport helicopters with independent engine systems, requires that they continue the flight with one engine inoperative (OEI). These stringent requirements, while permitting its operations from rooftops and oil rigs and flight to areas where no emergency landing sites are available, restrict the payload of a Category-A transport helicopter to a value safe for continued flight as well as for landing with one engine inoperative. The current certification process involves extensive flight tests, which are potentially dangerous, costly, and time consuming. These tests require the pilot to simulate engine failures at increasingly critical conditions, Flight manuals based on these tests tend to provide very conservative recommendations with regard to maximum takeoff weight or required runway length. There are very few theoretical studies on this subject to identify the fundamental parameters and tradeoff factors involved. Furthermore, a capability for real-time generation of OEI optimal trajectories is very desirable for providing timely cockpit display guidance to assist the pilot in reducing his workload and to increase safety in a consistent and reliable manner. A joint research program involving NASA Ames Research Center, the FAA, and the University of Minnesota is being conducted to determine OEI optimal control strategies and the associated optimal,trajectories for continued takeoff (CTO), rejected takeoff (RTO), balked landing (BL), and continued landing (CL) for a twin engine helicopter in both VTOL and STOL terminal-area operations. This proposed paper will present the problem formulation, the optimal control solution methods, and the key results of the trajectory optimization studies for both STOL and VTOL OEI operations. In addition, new results concerning the recently developed methodology, which enable a real-time generation of optimal OEI trajectories, will be presented in the paper. This new real-time capability was developed to support the second piloted simulator investigation on cockpit displays for Category-A operations being scheduled for the NASA Ames Vertical Motion Simulator in June-August of 1995. The first VMS simulation was conducted in 1994 and reported.
A prior trade study established the effectiveness of using Active Flow Control (AFC) for reducing the mechanical complexities associated with a modern high-lift system without sacrificing aerodynamic performance at low-speed flight conditions representative of takeoff and landing. The current technical report expands on this prior work in two ways: (1) a refined conventional high-lift system based on the NASA Common Research Model (CRM) is presented that is more representative of modern commercial transport aircraft in terms of stall characteristics and maximum Lift/Drag (L/D) ratios at takeoff and landing-approach flight conditions; and (2) the design trade space for AFC-enabled high-lift systems is expanded to explore a wider range of options for improving their efficiency. The refined conventional high-lift CRM (HL-CRM) concept features leading edge slats and slotted trailing edge flaps with Fowler motion. For the current AFC-enhanced high lift system trade study, the refined conventional high-lift system is simplified by substituting simply-hinged trailing edge flaps for the slotted single-element flaps with Fowler motion. The high-lift performance of these two high-lift CRM variants is established using Computational Fluid Dynamics (CFD) solutions to the Reynolds-Averaged Navier-Stokes (RANS) equations. These CFD assessments identify the high-lift performance that needs to be recovered through AFC to have the CRM variant with the lighter and mechanically simpler high-lift system match the performance of the conventional high-lift system. In parallel to the conventional high-lift concept development, parametric studies using CFD guided the development of an effective and efficient AFC-enabled simplified high-lift system. This included parametric trailing edge flap geometry studies addressing the effects of flap chord length and flap deflection. As for the AFC implementation, scaling effects (i.e., wind-tunnel versus full-scale flight conditions) are addressed, as are AFC architecture aspects such as AFC unit placement, number AFC units, operating pressures, mass flow rates, and steady versus unsteady AFC applications. These efforts led to the development of a novel traversing AFC actuation concept which is efficient in that it reduces the AFC mass flow requirements by as much as an order of magnitude compared to previous AFC technologies, and it is predicted to be effective in driving the aerodynamic performance of a mechanical simplified high-lift system close to that of the reference conventional high-lift system. Conceptual system integration studies were conducted for the AFC-enhanced high-lift concept applied to a NASA Environmentally Responsible Aircraft (ERA) reference configuration, the so-called ERA-0003 concept. The results from these design integration assessments identify overall system performance improvement opportunities over conventional high-lift systems that suggest the viability of further technology maturation efforts for AFC-enabled high lift flap systems. To that end, technical challenges are identified associated with the application of AFC-enabled high-lift systems to modern transonic commercial transports for future technology maturation efforts.
A design study was conducted for a remote lift-fan commercial V/STOL transport for the 1985 time period. The investigation centered on the commercial short haul transportation application to carry 100 passengers over trip distances of 400 nautical miles from a vertical takeoff and landing, and 800 nautical miles after a 1600 foot STOL takeoff. The study included investigation of alternate numbers and arrangements of lift fans and gas generators, fan control margins, and structural concepts. The sensitivity of direct operating costs to major airframe parameters, airframe costs, propulsion costs, yearly aircraft utilization rate, and trip distances are evaluated.
Early research on the development of machine vision algorithms to serve as pilot aids in aircraft flight operations is discussed. The research is useful for synthesizing new cockpit instrumentation that can enhance flight safety and efficiency. With the present work as the basis, future research will produce low-cost instrument by integrating a conventional TV camera together with off-the=shelf digitizing hardware for flight test verification. Initial focus of the research will be on developing pilot aids for clear-night operations. Latter part of the research will examine synthetic vision issues for poor visibility flight operations. Both research efforts will contribute towards the high-speed civil transport aircraft program. It is anticipated that the research reported here will also produce pilot aids for conducting helicopter flight operations during emergency search and rescue. The primary emphasis of the present research effort is on near-term, flight demonstrable technologies. This report discusses pilot aids for night landing and takeoff and synthetic vision as an aid to low visibility landing.
Aircraft takeoff and landing performance on slippery runways in crosswind, causing tire hydroplaning
Preliminary acoustic tests of the engine-over-the-wing concept as a method for reducing the aerodynamic noise created by conventional and short takeoff aircraft are discussed. Tests were conducted with a small wing section model having two flaps which can be set for either the landing or takeoff positions. Data was acquired with the flaps set at 10 degrees and 20 degrees for takeoff and 30 and 60 degrees for landing. The engine exhaust was simulated by an air jet from a convergent nozzle. Far field noise data are presented for nominal pressure ratios of 1.25, 1.4 and 1.7 for both the flyover and sideline modes.
The Pathfinding for Airspace with Autonomous Vehicles (PAAV) Concept Document, version 1.0, lays out the key challenges and potential solutions for the use of uncrewed aircraft (UA) technology for future regional air cargo operations. The challenges and solutions described in this document were informed by communications with the UA industry community (e.g., RTCA, the Federal Aviation Administration, and regional air cargo business operators), as well as the PAAV team’s research activities during the last two years including four tabletop exercises, a human-in-the-loop simulation study, a numerical simulation study, a functional allocation study, and flight data analysis (Appendix A). This document first describes the expected operational context of PAAV (Section 2), such as the flight mission, baseline UAS components, nominal operations, m:N operations (i.e., "m" remote pilots per "N" aircraft), and off-nominal operations. This context sets the scope for the PAAV concept development work. PAAV concept development assumes that UA operations will be increasingly autonomous. Thus, near- and far-term assumptions are defined (Section 3). PAAV identified seven key challenges for UA operations (Section 4): - Flight route planning - Separation and flow management - Traffic pattern integration - Contingency management - Taxi, takeoff, and landing - m:N operations - Communications operations The following 13 potential solutions to these challenges are then described (Section 5): - Scalable communications architecture - Data link - Designated UAS corridors - Crew planning for m:N operations - Flight route optimization - Traffic load-level control - Trajectory solutions with data link - Automated hazard avoidance for m:N operations - Traffic pattern integration (TPI) tool - Standard lost command and control (C2) link (LC2L) procedures - Automated hazard avoidance under LC2L - Auto-taxi, auto-takeoff, and auto-land - Ground control station (GCS) user interface for m:N operations The document attempts to link each of these solutions to one or more of the challenge areas. Novel solutions involving numerous automation technologies are needed to mitigate traffic and airspace management challenges, especially for realizing m:N operations and ensuring safety under LC2L conditions. The purpose of this document is to help understand alternatives and tradeoffs among potential solutions and provide a foundation for a cohesive PAAV concept that will be described and refined in subsequent concept versions.
Flight experiments were conducted with Ames Research Center's Quiet Short-Haul Research Aircraft to evaluate the influence of highly augmented control modes on the ability of pilots to execute precision instrument flight operations in the terminal area, particularly approaches to and landings on a short runway. The aircraft is a powered-lift, short-takeoff and landing configuration that is equipped with a modern digital fly-by-wire flight control system, a head-up display, and a solar head-down display that make it possible to investigate control concepts and display format and content for full envelope, powered-lift operations. Considerable attention has been devoted in this flight program to assessing flightpath and airspeed command and stabilization modes developed using nonlinear, inverse model-following methods. The primary benefit of this control concept was realized when the pilot was required to execute a complex transition and approach under instrument conditions and in the presence of a wide range of wind and turbulence conditions.
Flight experiments with NASA Ames Research Center's quiet short-haul research aircraft evaluated the influence of pursuit displays on the ability of pilots to execute precision-instrument flight operations in the terminal area, particularly approaches to and landings on a short runway. The aircraft is a powered-lift, short-takeoff and landing configuration equipped with a modern digital fly-by-wire flight control system, a head-up display, and a color head-down display that make it possible to investigate control and display concepts for full-envelope, powered-lift operations. Flight-path-oriented displays that provide status and command information in a format with minimal clutter were investigated. The pilots could fly the aircraft with the precision associated with flight-director guidance and with a high degree of situation awareness. The primary benefits of this display concept were realized when the pilot was required to execute a complex transition and approach under instrument conditions and in the presence of a wide range of wind and turbulence conditions.
Advanced takeoff procedures were developed for a Mach 2.62 high-speed civil transport configuration (HSCT) equipped with turbine bypass engines, with the goal of reducing the takeoff noise levels for certification to FAR 36, Stage 3 noise levels. The detailed takeoff and landing module for the Flight Optimizations System (FLOPS) computer program was used to generate takeoff profiles. All takeoff procedures were constrained to meet a FAR takeoff field length of 11,000 feet, as well as the minimum required engine-out climb gradients for each airbome segment. Aircraft noise levels at the FAR 36 certification points were calculated using the Aircraft Noise Prediction Program (ANOPP). The study showed that using advanced takeoff procedures in noise certification could result in a 2.25 dB reduction in the amount of noise suppression required to certify this configuration for Stage 3 noise limits. Advanced procedures also resulted in an 8 percent reduction in the 100 EPNdB noise footprint area compared to basic FAR 36 takeoff procedures. In addition, improvements in the lift-to-drag ratio using high-lift devices were shown to produce 1.81 dB more noise reduction when used in combination with advanced takeoff procedures.