SEARCH · Search NASA

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Noise of a model counterrotation propeller with reduced aft rotor diameter at simulated takeoff/approach conditions (F7/A3)

A model high-speed advanced counterrotation propeller, F7/A3, was tested in the NASA Lewis Research Center 9 by 15 foot Anechoic Wind Tunnel at simulated takeoff/approach conditions of 0.2 Mach number. Acoustic measurements were taken with an axially translating microphone probe, and with a polar microphone probe which was fixed to the propeller nacelle and could take both sideline and circumferential acoustic surveys. Aerodynamic measurements were also made to establish propeller operating conditions. The propeller was run at two setting angles (front angle/rear angle) of 36.4/43.5 and 41.1/46.4 degrees, forward rotor tip speeds from 165 to 259 m/sec, rotor spacings from 8.48 to 14.99 cm based on pitch change axis separation, and angles of attack to 16 degrees. The aft rotor diameter was 85 percent of the forward rotor diameter to reduce tip vortex-aft rotor interaction as a major interaction noise source. Results are compared with equal diameter F7/A7 data which was previously obtained under similar operating conditions. The aft rotor-alone tone was 7 dB lower for the reduced diameter aft rotor, due to reduced tip speed at constant rpm. Interaction tone levels for the F7/A3 propeller were higher at minimum row spacing and lower at maximum spacing.

Woodward, Richard P.↗

NASA NTRS1988

Noise of a model counterrotation propeller with reduced aft rotor diameter at simulated takeoff/approach conditions (F7/A3)

Woodward, Richard P.↗

NASA NTRS1977

Ceramics for the advanced automotive gas turbine engine: A look at a single shaft design

The results of a preliminary analysis of a single shaft regenerative design with a single stage radial turbine are presented to show the fuel economy that can be achieved at high turbine inlet temperatures, with this particular advanced design, if the turbine tip speed and regenerator inlet temperature are not limited. The engine size was 100 hp for application to a 3500 lb auto. The fuel economy was analyzed by coupling the engine to the auto through a continuously variable speed-ratio transmission and operating the system at constant turbine inlet temperature over the Composite Driving Cycle. The fuel was gasoline and the analysis was for a 85 F day. With a turbine inlet temperature of 2500 F the fuel economy was 26.2 mpg, an improvement of 18 percent over that of 22.3 mpg with a turbine inlet temperature of 1900 F. The turbine tip speed needed for best economy with the 2500 F engine was 2530 ft/sec. The regenerator temperature was approximately 2200 F at idle. Disk stresses were estimated for one single stage radial turbine and two two-stage radial-axial turbines and compared with maximum allowable stress curves estimated for a current ceramic material. Results show a need for higher Weibull Modulus, higher strength ceramics.

Nosek, S. M.↗

NASA NTRSDate not supplied

Conceptual Design Trade Studies for Acoustic Predictions of the NASA UAM Tiltrotor Reference Vehicle

A toolchain of low-and mid-fidelity tools is applied to NASA’s Urban Air Mobility tiltrotor reference vehicle to quantify trades in sizing, performance, and noise at the conceptual design level. The process includes conceptual sizing, comprehensive analysis, and acoustic analysis to design and analyze versions of the concept tiltrotor with differing design variables. Rotor tip speed is the primary design variable studied, with blade twist, blade taper, and blade number also considered. The noise metrics used are the FAA/EASA certification Effective Perceived Noise Levels for takeoff, flyover, and approach. Certification condition noise is calculated for all conditions in both conversion and airplane flight modes, with airplane mode flight resulting in noise 10-25EPNdB quieter than conversion mode and tip speed variation providing noise reduction up to 9EPNdB.

Acoustic↗

NASA NTRS1975

Study of noise sources in a subsonic fan using measured blade pressures and acoustic theory

Sources of noise in a 1.4 m (4.6 ft) diameter subsonic tip speed propulsive fan running statically outdoors are studied using a combination of techniques. Signals measured with pressure transducers on a rotor blade are plotted in a format showing the space-time history of inlet distortion. Study of these plots visually and with statistical correlation analysis confirms that the inlet flow contains long, thin eddies of turbulence. Turbulence generated in the boundary layer of the shroud upstream of the rotor tips was not found to be an important noise source. Fan noise is diagnosed by computing narrowband spectra of rotor and stator sound power and comparing these with measured sound power spectra. Rotor noise is computed from spectra of the measured blade pressures and stator noise is computed using the author's stator noise theory. It is concluded that the rotor and stator sources contribute about equally at frequencies in the vicinity of the first three harmonics of blade passing frequency. At higher frequencies, the stator contribution diminishes rapidly and the rotor/inlet turbulence mechanism dominates. Two parametric studies are performed by using the rotor noise calculation procedure which was correlated with test. In the first study, the effects on noise spectrum and directivity are calculated for changes in turbulence properties, rotational Mach number, number of blades, and stagger angle. In the second study the influences of design tip speed and blade number on noise are evaluated.

Hanson, D. B.↗

NASA NTRS1973

Noise levels of operational helicopters of the OH-6 type designed to meet the LOH mission

Formulas relating overall sound pressure level (OASPL) to parameters such as horsepower required, tip speed, and thrust for main and tail rotors are presented for standard and quieted helicopters. Formulas relating OASPL to engine parameters such as horsepower output and percent power turbine rpm are presented for unmuffled and muffled engines. The linear scale was used in preference to any of the weighted scales because it resulted in more consistent agreement with the test data when the SPL is expressed in the usual parameters of tip speed, thrust generated and power required. It is recognized that the linear scale does not adequately reflect hearing response, and hence is not a good absolute measure for detection by humans. However, linear OASPL is believed to be useful as a relative means of comparing noise level variations of individual components in similar helicopters with reasonably modest design changes.

Wagner, R. A.↗

NASA NTRS1993

Propfan noise propagation

The unconventional supersonic tip speed of advanced propellers has led to uncertainties about Propfan's noise acceptability and compliance with Federal Aviation Noise Regulation (FAR 36). Overhead flight testing of the Propfan with an SR-7L blade during 1989's Propfan Test Assessment (PTA) Program have shown unexpectedly high far-field sound pressure levels. This study here attempts to provide insights into the acoustics of a single-rotating propeller (SRP) with supersonic tip speed. At the same time, the role of the atmosphere in shaping the far-field noise characteristics is investigated.

George, Albert R.↗

NASA NTRS1985

Laboratory experiments on active suppression of advanced turboprop noise

The noise generated by supersonic tip speed propellers may be a cabin environment problem for future propeller-driven airplanes. Active suppression from speakers inside the airplane cabin has been proposed for canceling out this noise. The potential of active suppression of advanced turboprop noise was tested by using speakers in a rectangular duct. Experiments were first performed with sine wave signals. The results compared well with the ideal cancellation curve of noise as a function of phase angle. Recorded noise signals from subsonic and supersonic tip speed propellers were than used in the duct to deterthe potential for canceling their noise. The subsonic propeller data showed significant cancellations but less than those obtained with the sine wave. The blade-passing-tone cancellation curve for the supersonic propeller was very similar to the subsonic curve, indicating that it is potentially just as easy to cancel supersonic as subsonic propeller blade-passing-tone noise. Propeller duct data from a recorded propeller source and spatial data taken on a propeller-drive airplane showed generally good agreement when compared versus phase angle. This agreement, combined with the similarity of the subsonic and supersonic duct propeller data, indicates that the area of cancellation for advanced supersonic propellers will be similar to that measured on the airplane. Since the area of cancellation on the airplane was small, a method for improving the active noise suppression by using outside speakers is discussed.

Dittmar, J. H.↗

NASA NTRS1973

A comparison of the overall and broadband noise characteristics of full-scale and model helicopter rotors.

The broadband noise generated by full-scale and model rotors is compared in terms of spectral content and the dependence on tip speed and rotor thrust/pitch angle. Low frequency broadband noise and high frequency broadband noise are studied separately and blade 'scaling' effects are outlined. The degree of agreement between measurements and theoretical and semi-empirical prediction methods is reviewed together with the directionality patterns. The parameters relating to the overall noise are also discussed. It is shown that in general good agreement is obtained between the full-scale and model rotors when considering spectral content and the dependency of the noise levels on tip speed and thrust. The scaling factors usually considered applicable to the low frequency broadband noise do not, however, appear to apply to either the model or full scale rotors.

Leverton, J. W.↗

NASA NTRS1982

Model helicopter rotor low frequency broadband noise

The results of an experimental investigation of low frequency broadband noise (LFBN) radiated from model helicopter rotors are presented. The results up to tip Mach number of 0.50 suggest that the peak sound pressure level (SPL) of LFBN appears to follow tip Mach number to a fourth power law and rms velocity of turbulence to a second power law. The experimental results on the effect of tip speed and advance ratio on the peak SPL of LFBN can be explained on the basis of a simple scaling law. However, the experimental results on the effect of blade loading on the peak SPL of LFBN is still not clearly understood. A simple peak SPL scaling law for noise from a helicopter in forward flight encountering a sinusoidal gust is also developed. The trends predicted by the scaling law with the experimental results are found satisfactory for the cases of variation of the peak SPL of LFBN with tip speed and advance ratio.

Humbad, N. G.↗

NASA NTRS1976

Experimental and theoretical studies of subsonic fan noise

The noise generated by inlet turbulence impinging on a subsonic axial flow fan was studied as a function of tip speed, flow coefficient, and intensity and scale of turbulence was carried out. Both turbulence and far field acoustic measurements were made. The new elements introduced in the theoretical analysis were accounting for blade loading dependent noise mechanisms and consideration of anisotropic turbulence impinging on the rotor because of inlet flow contraction effects. Experimentally an unexplained increase of noise at about 1/2 and 1 1/2 times blade passsing frequency was observed at low flow coefficients even though there was no evidence of compressor surge. In the final version the theory does a fair job of predicting variations of noise with blade loading and tip speed. Alteration of inlet turbulence length scales produced some but not very pronounced changes in the far field PWL spectra. Some degree of eddy contraction and resulting anisotropy were essential to explain the concentration of energy around blade passing frequencies.

Mani, R.↗

NASA NTRS1979

Study of blade aspect ratio on a compressor front stage aerodynamic and mechanical design report

A single stage compressor was designed with the intent of demonstrating that, for a tip speed and hub-tip ratio typical of an advanced core compressor front stage, the use of low aspect ratio can permit high levels of blade loading to be achieved at an acceptable level of efficiency. The design pressure ratio is 1.8 at an adiabatic efficiency of 88.5 percent. Both rotor and stator have multiple-circular-arc airfoil sections. Variable IGV and stator vanes permit low speed matching adjustments. The design incorporates an inlet duct representative of an engine transition duct between fan and high pressure compressor.

Burger, G. D.↗

NASA NTRS1974

Perturbation solutions for the influence of forward flight on helicopter rotor flapping stability

The stability of the flapping motion of a helicopter rotor blade in forward flight is investigated, using a perturbation technique which gives analytic expressions for the eigenvalues, including the influence of the periodic aerodynamic forces in forward flight. The perturbation solutions are based on small advance ratio (the ratio of the helicopter forward speed to the rotor tip speed). The rotor configurations considered are a single, independent blade; a teetering rotor; a gimballed rotor with three, four, and five or more blades; and a rotor with N independent blades. The constant coefficient approximation with the equations and degrees of freedom in the nonrotating frame represents the flap dynamic reasonably well for the lower frequency modes, although it cannot, of course, be completely correct. The transfer function of the rotor flap response to sinusoidal pitch input is examined, as an alternative to the eigenvalues as a representation of the dynamic characteristics of the flap motion.

Johnson, W.↗

NASA NTRS1980

Comparison of several inflow control devices for flight simulation of fan tone noise using a JT15D-1 engine

To enable accurate simulation of in-flight fan tone noise during ground static tests, four devices intended to reduce inflow disturbances and turbulence were tested with a JT15D-1 turbofan engine. These inflow control devices (ICD's) consisted of honeycomb/screen structures mounted over the engine inlet. The ICD's ranged from 1.6 to 4 fan diameters in size, and differed in shape and fabrication method. All the ICD's significantly reduced the BPF tone in the far-field directivity patterns, but the smallest ICD's apparently introduced propagating modes which could be recognized by additional lobes in the speeds; at supersonic fan tip speed the smallest ICD's had some measurable loss, but the largest had no loss. Data from a typical transducer show that the unsteady inflow distortion modes (turbulence) were eliminated or significantly reduced when either of the ICD's was installed. However, some steady inflow distortion modes remained.

Mcardle, J. G.↗

NASA NTRS1983

An experimental investigation and numerical prediction of thermomechanical phenomena in high speed rotor tip rubbing

A thermomechanical study of the intermittent rubbing of a rotor blade tip and a casing seal is carried out taking into account the existence of thermal contact resistance. The effect of the thermal properties of a plasma sprayed coating on the blade tip is studied. The influence of a variable heat generation and variable thermal contact resistance at the blade tip as it passes along the path of rubbing is also discussed.

Emery, A. F.↗

NASA NTRS1986

Experimental short-duration techniques

Short-duration facilities used for gas turbine studies are described. Data recording techniques; and instruments (thin-film heat flux gages, high-frequency response pressure measurements, total temperature probes, measurement of rotor tip speed, active measurement of tip clearance) are presented.

Dunn, Michael G.↗

NASA NTRS1987

Computation of transonic potential flow on helicopter rotor blades

Two computer codes, the full-potential three-dimensional (FP3D) code and the full-potential rotor (FPR) code have recently been developed. Both of these codes solve the three-dimensional conservative formulation of the full potential equation. The FPR code was developed at the U.S. Army Aeroflightdynamics Directorate (AFDD) while the FP3D code was a joint development by ONERA and AFDD. Both of these codes were used to predict the nonlifting, unsteady flow over a rotor operating at high advance ratio and tip speed. Three different rotor tip planform shapes were studied: a rectangular tip, a 30 deg aft swept tip and a 30 deg forward swept tip. Results of these computations are compared to results obtained using an earlier small-disturbances code. Also, the lifting flow over a rectangular tip operating at a slightly different condition was computed. These results are also compared with the small disturbances computations and with experimental results.

Costes, M.↗

NASA NTRS1999

A Mode Detection Method Using the Azimuthal Directivity of a Turbofan Model

The azimuthal, far field directivity of a scale fan model was measured in high resolution. The model is a 12 inch diameter rotor with 16 blades followed by 40 stator vanes. The tests were conducted at the nominal 100% speed corresponding to a tip speed of 905 ft/sec. Measurement of the radiated sound field, forward of the fan, was made in an anechoic chamber with an inflow control device and a baffle separating the aft and forward radiated interaction noise. The acoustic field was surveyed with a circular hoop array of 16 microphones which was moved to 14 axial stations. At each axial station the hoop was rotated in half-degree increments to take 736 points in the azimuthal angle. In addition to sound pressure level, the phase angle relative to a reference microphone was measured at each point. The sound pressure level is shown to vary in patterns by 10-15 dB especially for the fundamental tone but also for the first and second harmonic. A far field mode detection method has been developed and used with the data which determines the modes generated by the fan and which then interact to form the azimuthal directivity.

Thomas, R. H.↗