Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermodynamic Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Relating phase transitions to pore size distributions and mechanical mortar properties in CSA-OPC-C$ based systems – The potential impact of delayed straetlingite formation

The scope of this research is to investigate the performance evolution of five ternary CSA-OPC-Cs systems. Time resolved thermodynamic modeling was employed to gain insight into changes in the volume fractions of the hydrating pastes and link these changes to trends in the pore size distributions of the mortars. Pore solution analyses were performed to investigate which hydrates have the potential to exert high crystallization pressures. In three out of five blends the resulting tensile stress exceeded the tensile strength of the materials, resulting in the occurrence of coarse pores, which could be linked to the measured compressive strengths. Two damaging crystallization processes were identified in the investigated blends. One is the continuous precipitation of ettringite at high supersaturation in a system with high anhydrite addition. The other is the delayed crystallization of straetlingite at high supersaturation and crystallization pressure in the confined environment of mature pastes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deterioration mechanism of alkali-activated materials in sulfuric acid and the influence of Cu: A micro-to-nano structural, elemental and stable isotopic multi-proxy study

In this study, a multi-proxy approach combining {sup 29}Si, {sup 27}Al and {sup 1}H MAS-NMR, FEG-EPMA, XANES at the Cu K-edge and XRD analytics with hydrochemical tools such as ICP-OES analyses, oxygen-isotope signatures, and thermodynamic modelling was applied to K-silicate-activated metakaolin specimens - with and without CuSO{sub 4}·5H{sub 2}O addition - exposed to sulfuric acid at pH = 2 for 35 days. The results revealed a multistage deterioration mechanism governed by (i) acid diffusion, (ii) leaching of K-A-S-H, (iii) microstructural damage related to precipitation of expansive (K,Ca,Al)-sulfate-hydrate phases (iv) complete dissolution of the K-A-S-H framework, (v) and formation of silica gel in the outermost corroded regions. Copper ions were mainly located in layered spertiniite-chrysocolla-like phases in the as-cured materials. The results demonstrate an overall negative effect of Cu addition on chemical material durability, implying that the reported higher durability of Cu-doped AAM in biocorrosion environments can be best explained by bacteriostatic effects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reactions of self-healing agents and the chemical binding of aggressive ions in sea water: Thermodynamics and kinetics

New self-healing agents that can chemically bind seawater ions invading cracked cementitious materials were proposed. The potential of self-healing and binding of seawater ions were investigated by thermodynamic modeling. It was found that CaO-NaAlO{sub 2} and CaO-metakaolin agents can have Cl{sup −}, SO{sub 4}{sup 2−} and Mg{sup 2+} chemically bound by reacting with sea water to form Friedel's salt, Kuzel's salt, ettringite and hydrotalcite. The removal of Cl{sup −} from seawater firstly increased and then decreased with the increase of Ca/Al molar ratio in both agents, while the removal of Mg{sup 2+} and SO{sub 4}{sup 2−} were hardly influenced and approximated 100%. Because NaAlO{sub 2} dissolves and releases Al(OH){sub 4}{sup −} rapidly, precipitates binding Cl{sup −}, SO{sub 4}{sup 2−} and Mg{sup 2+} were formed fast. In comparison, the reaction of metakaolin binding aggressive ions occurred after 3 days. Because of the faster reaction and the capacity to make [Cl{sup −}]/[OH{sup −}] lower in the solution, CaO-NaAlO{sub 2} would be more efficient for self-healing and mitigating reinforcement corrossion than CaO-metakaolin.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crack-Free 30% Chromium-Nickel Alloy Welding Products for Nuclear Service

We report prior research in the development of 30% chromium-nickel alloy nuclear welding wires has resulted in the resolution of primary water stress corrosion cracking (PWSCC) and ductility dip cracking (DDC) as well as improvement in solidification cracking (SC) resistance. The resolution of DDC exhibits some Laves phase, which has a negative effect on SC resistance. In this study, the use of an alternate carbide former, tantalum (Ta), in combination with niobium (Nb) was researched. Three heats of recently designed Filler Metal 52MSS-Ta (i.e., HV1648, HV1673A, and VX131WXW) were melted, fabricated, and systematically studied. DDC and SC were evaluated with thermodynamic modeling using the Scheil solidification simulation model, two types of varestraint tests, and strain-to-fracture (STF) testing. The varestraint and STF test results showed an improved SC resistance with reduced Laves phase and concurrent excellent DDC resistance. Optimized compositions with low Laves phase also exhibited high threshold strain values (TSVs) in the STF test. VX131WXW — which contains 2.81 wt-% Ta, 0.6 wt-% Nb, and 6 wt-% iron (Fe) - exhibited a TSV of 24%. Thermo-Calc computed the Laves phase to be 0.24% for VX131WXW compared to 0.06% in HV1673A. This difference in Laves phase resulted in the lower SC resistance of VX131WXW compared to HV1673A when measured with longitudinal varestraint testing. The maximum crack distance for HV1673A was about 0.6 mm while that of heat VX131WXW was about 1.0 mm. The typical diluted weld deposit made with VX131WXW was also resistant to PWSCC due to the chromium content exceeding 24%. These simultaneous results mark progress toward crack-free welds and provide direction for further optimization of Ta-containing filler metals.

30% chromium-nickel alloy↗
DOE OSTI2020

Thermodynamics and kinetics of solution combustion synthesis: Ni(NO 3 ) 2 + fuels systems

Solution combustion synthesis (SCS) utilizes exothermic self-propagating reactions to prepare nanoscale materials that can be used widely in energy, electronics, and biomedical technologies and other applications. SCS is a specific variety of a more general combustion synthesis (CS) method. Investigations of the thermodynamics, kinetics, and the mechanisms of SCS reactions, are not as well studied as the other CS processes. This work reports on a systematic study of the thermodynamics and kinetics of SCS reactions involving Ni(NO 3 ) 2 , an oxidizer, and either glycine (C 2 H 5 NO 2 ) or hexamethylenetetramine (HMT, C 6 H 12 N 4 ) as fuels. A thermodynamic modeling approach, based on the Gibbs free energy minimization principle, is applied to the simultaneous calculations of the adiabatic temperatures and compositions of the equilibrium products. Our calculations reveal the influence of fuel-to-oxidizer ratio, amount of water, and the oxygen in air on the combustion temperature under adiabatic conditions and the composition of the resulting products. We have, in turn, measured the combustion temperature and phase composition of products and compared them with the calculations. Variations of drying times for the solutions yield precursor gels with varying water contents. This approach enables the manipulation of combustion parameters and confirms the use of calculated activation energies for reactions using the Merzhanov-Khaikin method. Here, the results show that SCS reactions in fuel-lean solutions producing NiO have higher activation energy in contrast to reactions with fuel-rich solutions that form Ni. Reduction of activation energies due to the increase in the fuel-to-oxidizer ratio could be related to the observed change of the rate-limiting stages of the endothermic decomposition of the individual reactants to the exothermic decomposition of coordinate compounds formed between the reactants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Planet Formation by Gas-assisted Accretion of Small Solids

We compute the accretion efficiency of small solids, with radii 1 cm ≤ R s ≤ 10 m, on planets embedded in gaseous disks. Planets have masses 3 ≤ M p ≤ 20 Earth masses (M ⊕ ) and orbit within 10 au of a solar mass star. Disk thermodynamics is modeled via 3D radiation-hydrodynamics calculations that typically resolve the planetary envelopes. Both icy and rocky solids are considered, explicitly modeling their thermodynamic evolution. The maximum efficiencies of 1 ≤ R s ≤ 100 cm particles are generally ≲10%, whereas 10 m solids tend to accrete efficiently or be segregated beyond the planet’s orbit. A simplified approach is applied to compute the accretion efficiency of small cores, with masses M p ≤ 1 M ⊕ and without envelopes, for which efficiencies are approximately proportional to $M^{2/3}_{p}$. The mass flux of solids, estimated from unperturbed drag-induced drift velocities, provides typical accretion rates dM p /dt ≲ 10 -5 M ⊕ yr -1 . In representative disk models with an initial gas-to-dust mass ratio of 70–100 and total mass of 0.05–0.06 M ⊙ , the solids’ accretion falls below 10 -6 M ⊕ yr -1 after 1–1.5 Myr. The derived accretion rates, as functions of time and planet mass, are applied to formation calculations that compute dust opacity self-consistently with the delivery of solids to the envelope. Assuming dust-to-solid coagulation times of ≈0.3 Myr and disk lifetimes of ≈3.5 Myr, heavy-element inventories in the range 3–7 M ⊕ require that ≈90–150 M ⊕ of solids cross the planet’s orbit. The formation calculations encompass a variety of outcomes, from planets a few times M ⊕ , predominantly composed of heavy elements, to giant planets. The peak luminosities during the epoch of the solids’ accretion range from ≈10 -7 to ≈10 -6 L ⊙ .

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Mobility of heavy rare earth elements in magmatic-hydrothermal systems: Experimental determination of DyPO 4 solubility in supercritical fluids

Dysprosium (Dy) is part of the heavy rare earth elements (REE) and a critical component in the production of high-performance super magnets used in wind turbines, electric vehicles, and other green technologies. The HREE phosphate, xenotime, is commonly associated with hydrothermal systems, where the mobility, fractionation, and deposition of REE are controlled by the stability of aqueous complexes and solubility of REE minerals which depend on temperature, pressure, and fluid composition (salinity, pH, and ligand availability). Here, we conducted a series of synthetic DyPO 4 solubility experiments in NaCl-HCl-bearing aqueous solutions (pH of 2 at 25 °C) from 500 to 700 °C and 1.5 kbar using externally heated pressure vessels. DyPO 4 displays a strong prograde solubility with temperature across all studied fluid salinities (0–0.5 m NaCl). The DyPO₄ solubility isotherms at 500 °C, 600 °C, and 700 °C show a complex relationship with salinity where DyPO₄ solubility is highest (39.2–1552 ppm at 500–700 °C) in 0 m NaCl solutions, decreases strongly (21–331 ppm at 500–700 °C) in the 0.06 m NaCl solutions and remains relatively constant in the 0.25 m (42.8–248 ppm) and 0.5 m NaCl (40.2–124 ppm) solutions. Thermodynamic modeling suggests that pH increases as a function of temperature and salinity, and controls solubility due to the stability of chloride complexes (i.e., DyCl +2 and DyCl 2 + ) at 500–600 °C, transitioning to hydroxyl complexes (i.e., Dy(OH) 3 0 ) dominating at 700 °C and relatively alkaline pH. Comparison with NdPO 4 solubility data indicates that the light REE in monazite is significantly more soluble than the heavy REE in xenotime in saline fluids at high temperature (500–700 °C), implying efficient light/heavy REE fractionation in supercritical fluids. The lower solubility of DyPO 4 relative to NdPO 4 suggests that at high temperatures, acidic (pH 2–4), low-salinity (∼5 wt% NaCl) fluids will favor the precipitation of xenotime over monazite as it will cool from 700 °C to below 500 °C. These observations align with paragenetic mineral assemblages in NYF pegmatites (e.g., Baveno, Italy), where xenotime commonly immobilizes heavy REE during the high-temperature hydrothermal stages.

58 GEOSCIENCES↗
DOE OSTI2020

Requirements and Conceptual Design of Off-gas Systems for the Reprocessing of Metallic Fuels

An assessment has been conducted to determine how key regulations regarding volatile radionuclide emissions to the atmosphere may apply to the off-gas streams associated with electrochemical reprocessing. The scope of this assessment was based upon a generic electrochemical reprocessing scheme with a throughput rate of 200 MTIHM/y applied to metallic fuel discharged from a sodium fast reactor (SFR), but the findings are able to be translated to other advanced nuclear scenarios as merited. Air dispersion modeling was performed using the EPA CAP-88 model and evaluated the uncontrolled decontamination factors (DFs) that would be required to achieve regulatory compliance with the dose-based limits set forth by EPA regulation 40 CFR 190.10(a). These DFs were compared to those required by fuel cycle–based limits set forth by EPA regulation 40 CFR 190.10(b). Two theoretical sites with disparate climatological conditions were selected for air dispersion modeling (Idaho and Tennessee). The radionuclides modeled included 3 H, 85 Kr, 129 I, and selected alpha-emitting transuranic isotopes (referred to here as 239 Pu-TRU <1y ). It was found that the fuel cycle-based limits in 40 CFR 190.10(b) are most restrictive for 85 Kr and 239 Pu-TRU <1y , with DFs of 3 and 6.1E+09, respectively. The dose-based limit as derived from 40 CFR 190.10(a) could require mitigation of tritium in some scenarios, with an estimated DF of about 3 for the reference scenarios. The fuel cycle-based limit for 129 I resulted in a DF of about 240 for the reference scenario. The need for iodine mitigation based on dose to the public depended upon the physical form of iodine as either particulate or vapor-phase species. Emission of iodine from the facility as a vapor necessitated DFs of about 2 but emission as a particulate would require DFs >6,000 to meet thyroid dose-based limits. Effects of physical form on needed iodine mitigation are significant, but the understanding of speciation of iodine both during electrochemical reprocessing and after release to the atmosphere is limited. The electrochemical processing unit operations were evaluated to identify potential release points for the volatile radionuclides and to assess the potential for retention of the radionuclides within the process (thus decreasing the need for mitigation). Mitigation strategies for 3 H, 85 Kr, 129 I, and 239 Pu-TRU <1y were identified. In all cases, there are reasonably achievable pathways to regulatory compliance, although in some cases additional R&D is merited to verify the chemical speciation of these isotopes and to develop and demonstrate potential treatment technologies for this application. Whether or not additional off-gas controls (beyond common operations such as HEPA filtration and oxygen and moisture control) are needed for any of these regulated or volatile radionuclides depends on the (a) type of facility (NRC-regulated or DOE), (b) used fuel process rate, (c) used fuel burnup and composition, (d) speciation and retention of volatile radionuclides in the process and in the cell gas cleanup system, (e) site-specific parameters such as location, meteorology, stack height, and site boundaries, and (f) levels of conservatism and safety factors used in assessing compliance to air emissions regulations. Performance of this assessment revealed several areas where information is lacking or additional research is required in order to better determine if or what kinds of off-gas control might be needed. First, and most significantly, the understanding of the chemical speciation and physical form and partitioning of iodine during electrochemical processing operations is lacking and prevents the ability to accurately assess the potential iodine mitigation requirements. Future research in this area should be multifaceted and include thermodynamic modeling of iodine speciation in different process steps, experiments to quantify the kinetics of vapor-phase and melt-phase transitions, bench-scale experiments to determine the potential chemical and physical form of iodine emissions from the electrorefining process, and verification of iodine behavior with experiments utilizing operational facilities. Similarly, an improved understanding of iodine behavior in the environment after release from the facility stack will be required to refine dose estimations, as particulate and vapor-phase emissions result in significantly different doses to the MEI.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Fundamental Effects of Al and Ta on Microstructure and Phase Transformations in the Al–Cr–Mo–Ta–Ti Refractory Complex Concentrated Alloy System

The effect of aluminum and tantalum concentrations on a refractory metal complex concentrated alloy is reported, particularly with respect to their effect on microstructure and phase composition of the alloy in cast and annealed form. Alloys with an equiatomic composition, (AlCrMoTaTi), an aluminum-lean composition (Al 0.75 CrMoTaTi), and a tantalum-lean composition (AlCrMoTa 0.75 Ti) are produced via arc melting. The alloys exhibit multiphase structures, confirmed by X-ray diffraction, microstructural characterization, and thermal analysis. The minor off-equiatomic adjustments of aluminum and tantalum in this alloy system did not drastically alter the prevalence of the Cr–Ta-based Laves phase. Correlations between thermodynamic predictions and observed phase transformations via thermal analysis are improved upon refinement of calculations removing impractical intermediate phases. As a result, experimental findings provide information for the refinement of thermodynamic modeling and deliver additional insight into the optimization of alloy compositions within this five-component system.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Lattice-Distortion-Enhanced Yield Strength in a Refractory High-Entropy Alloy

Severe distortion is one of the four core effects in single-phase high-entropy alloys (HEAs) and contributes significantly to the yield strength. However, the connection between the atomic-scale lattice distortion and macro-scale mechanical properties through experimental verification has yet to be fully achieved, owing to two critical challenges: 1) the difficulty in the development of homogeneous single-phase solid-solution HEAs and 2) the ambiguity in describing the lattice distortion and related measurements and calculations. Here, a single-phase body-centered-cubic (BCC) refractory HEA, NbTaTiVZr, using thermodynamic modeling coupled with experimental verifications, is developed. Compared to the previously developed single-phase NbTaTiV HEA, the NbTaTiVZr HEA shows a higher yield strength and comparable plasticity. The increase in yield strength is systematically and quantitatively studied in terms of lattice distortion using a theoretical model, first-principles calculations, synchrotron X-ray/neutron diffraction, atom-probe tomography, and scanning transmission electron microscopy techniques. These results demonstrate that severe lattice distortion is a core factor for developing high strengths in refractory HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Linking DSC/TGA to Cell Levels: Energetics, Evolved Gases, and Thermal Safety of NMC811‐Graphite Micro‐Cell

Thermochemical characterization of battery materials links intrinsic material properties to decomposition pathways, heat generation, and gas evolution that govern performance and safety. Despite extensive work on NMC811-Graphite, variability across partial configurations and the limited adoption of micro-cell architectures (cathode+anode+electrolyte+separator) hinder robust cell-scale interpretation. Accordingly, this work establishes a bottom-up, component-resolved methodology integrating DSC/TGA, evolved gas analysis (EGA), and in situ XRD to link decomposition pathways and energy release across partial and micro-cell configurations, providing a transferable assessment of safety and stability in emerging chemistries. In separator-free configurations, the gas–solid reaction between cathode-evolved O 2 and anode-leached Li dominates the net heat release (1139 J g −1 ). In contrast, in the micro-cell configuration, the separator hinders O 2 transport and alters the timing and pathways of other reactions, and reduces the net energy release to 618 J g −1 . Energy release was organized into defined temperature windows that provide a framework for a thermodynamic model combining quantified gas evolution with selected decomposition pathways and effective reaction enthalpies to estimate net specific energy release, with agreement between DSC and cell-level tests. Ex situ XPS of heat-treated samples extends post-mortem analysis to thermal-abuse regimes, supporting key pathway elements.

25 ENERGY STORAGE↗
DOE OSTI2022

Current challenges in hydrate‐based desalination: Kinetic and thermodynamic perspective

Abstract Water scarcity is becoming a severe problem worldwide due to inadequate freshwater resources and swift population growth. Seawater desalination is one of the vital approaches to meet the demand for freshwater. However, energy and associated costs with conventional seawater desalination techniques are incentivizing non‐conventional water desalination processes. Water desalination using gas hydrates formation is one of the emerging non‐conventional processes. In this perspective article, recent advances in hydrate‐based seawater desalination (HBSD) have been critically analyzed to outline a future path towards a clean and efficient hydrate‐based desalination process. It provides a detailed comparison of various processes developed over decades, and measured desalination efficiencies with their process details. Moreover, the current challenges, limitations, and future perspectives of hydrate‐based desalination are also discussed. The study also recapitulates the thermodynamics and kinetics aspects of the hydrate‐based desalination process. In addition, various factors controlling the desalination efficiencies, such as control of the separation of hydrate crystals, salt deposition on hydrate particles, and hydrate morphology, were thoroughly investigated with their proposed process designs. The kinetics of hydrate formation is also assessed, with the possibility of a zero‐induction regime and its consequent impact on hydrate morphology. The current capabilities of the thermodynamics models (Gibbs energy minimization + electrolyte equation of state) were discussed using various commercially available software. Additionally, the role of hydrate promotors is also discussed, which can reduce the higher cost associated with the hydrate‐based desalination process.

Khan, Muhammad Naveed↗
DOE OSTI2022

A liquid stratification model to predict failure in thermally damaged EBW detonators

In previous work, commercially available downward facing exploding bridgewire detonators (EBWs) were exposed to elevated temperatures. These detonators were then initiated using a firing set which discharged a high amplitude short duration electrical pulse into a thin gold bridgewire. Responses of the detonators were measured using photonic doppler velocimetry (PDV) and high-speed photography. A time delay of 4 μs between EBW initiation and first movement of an output flyer separated operable detonators from inoperable detonators or duds. Here, we propose a simple method to determine detonator operability from the calculated state of the detonator at the time the firing set is initiated. The failure criterion is based on the gap distance between the exploding bridgewire (EBW) and the adjacent initiating explosive within the detonator which is low-density pentaerythritol tetranitrate (PETN) that melts between 413-415 K (140-142 ºC). The gap forms as PETN melts and flows to the bottom of the input pellet. Melting of PETN is modeled thermodynamically as an energy sink using a normal distribution spread over a temperature range between the onset temperature of 413 K and the ending temperature of 415 K. The extent of the melt is determined from the average temperature of the PETN. The PETN liquid is assumed to occupy the interstitial gas volume in the lower part of the input pellet. The vacated volume from the relocated liquid forms the gap between the EBW and the PETN. The remaining sandwiched layer consists of solid PETN particles and gas filling interstitial volume. We predict that a threshold gap between 17-27 μm separates properly functioning detonators from duds.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Engineering Supramolecular Polymer Conformation for Efficient Carbon Nanotube Sorting

Supramolecular polymer sorting is a promising approach to separating single-walled carbon nanotubes (CNTs) by electronic type. Unlike conjugated polymers, they can be easily removed from the CNTs after sorting by breaking the supramolecular bonds, allowing for isolation of electronically pristine CNTs as well as facile recycling of the sorting polymer. However, little is understood about how supramolecular polymer properties affect CNT sorting. Herein, chain stoppers are used to engineer the conformation of a supramolecular sorting polymer, thereby elucidating the relationship between sorting efficacy and polymer conformation. Through NMR and UV–vis spectroscopy, small-angle X-ray scattering (SAXS), and thermodynamic modeling, it is shown that this supramolecular polymer exhibits ring–chain equilibrium, and that this equilibrium can be skewed toward chains by the addition of chain stoppers. Furthermore, by controlling the stopper–monomer ratio, the sorting yield can be doubled from 7% to 14% without compromising the semiconducting purity (>99%) or properties of sorted CNTs.

42 ENGINEERING↗
DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗
DOE OSTI2022

A New Recycled Al–Si–Mg Alloy for Sustainable Structural Die Casting Applications

The use of secondary aluminum for structural components in the automotive industry is limited by the high Fe contents in recycled alloys which often result in the formation of brittle β-Al 5 FeSi phase which reduces the ductility of aluminum castings. In this study, a new secondary Al-Si-Mg alloy with high Fe content (about 0.44 wt.%) was developed for die casting applications. Based on thermodynamic modeling, manganese was added to obtain a designed Fe-to-Mn ratio of 2 which successfully suppressed the formation of β-Al 5 FeSi phase, by forming α-Al 15 (Fe,Mn) 3 Si 2 phase with rounded or hexagonal morphology. Additionally, a fine needle-like π-Al 8 FeMg 3 Si 2 phase was also formed within the eutectic regions. The new recycled alloy showed comparable mechanical properties in as-cast and heat treated (T5 and T6) conditions to three major primary die cast alloys (≤ 0.2 wt.% Fe) with similar composition. Ductility up to 7.4% from tensile elongation was achieved in as-cast recycled alloy due to the modification and refinement of α-Al 15 (Fe,Mn) 3 Si 2 by Mn and Sr additions. Tensile elongation was further improved to 9.1% after T6 treatment as a result of dissolution of π-Al 8 FeMg 3 Si 2 phase, defragmentation of α-Al 15 (Fe,Mn) 3 Si 2 and the spheroidization of Si phase. This new alloy provides a promising path for increasing usage of recycled aluminum with high Fe content in structural die castings for automotive and other applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid State Reduction Driven Synthesis of Mn Containing Multi-principal Component Alloys

In recent years, high entropy alloys (HEAs), also known as multi-principal component alloys (MPCAs) have emerged as a new and exciting class of materials. This paper reports on the solid state reduction synthesis of a series of CoFeNiMn-based MPCA compositions, starting from a mixture of the corresponding oxides. One of the aims of the study was to test whether the degree of reduction of MnO, a highly stable oxide, could be enhanced by tailoring the alloy composition. Specifically, the influence of Ni content was studied because Ni exhibits a significant negative enthalpy of mixing with Mn. High purity precursor powders of Co(OH) 2 , Fe 2 O 3 , MnO 2 , and NiO were milled and mixed using standard ceramic processing methods. Here, the nominal sample compositions (assuming complete oxide reduction) were (CoFeMn) x Ni (1-x) , for x = 0, 0.083, 0.166, and 0.25. The oxide samples were subjected to a series of isothermal reduction anneals in flowing 3 pct H 2 –Ar at 1100 °C. The resulting microstructures were characterized using scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The composition of the resulting MPCAs was determined quantitatively using wavelength dispersive spectroscopy (WDS) in the electron microprobe. The study revealed that for each of the initial oxide compositions studied, it was possible to achieve an MPCA with ~ 25 at. pct Mn. These results were found to be consistent with the predictions of a thermodynamic model whereby a negative enthalpy of mixing (ΔH mix ), combined with a contribution from configurational entropy, can offset a positive free energy of reduction (ΔG red ). The incorporation of vibrational entropy into first principles calculations was found to have a significant effect on the predicted crystal structure of the MPCAs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

First Principles Evaluation of Phase Stability in the In-Sn Binary System

Abstract The In-Sn binary alloy system exhibits several unusual features that challenge crystallographic and thermodynamic expectations. We combine first principles total energy calculation with simple thermodynamic modeling to address two key points. First, we evaluate energies along the Bain path to interpret the discontinuous transition between the phases α-In (Pearson type tI2) and β-In 3 Sn (also Pearson type tI2) that are identical in symmetry. Second, we demonstrate that the solid solution phases β-In 3 Sn and γ-InSn 4 (Pearson type hP1) exist at high temperatures only, and they exhibit eutectoid decompositions at low temperatures.

Chemistry↗