Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transitional flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Cavity Unsteady-Pressure Measurements at Subsonic and Transonic Speeds

An experimental investigation was conducted in the Langley 8-Foot Transonic Pressure Tunnel to determine the flow characteristics of rectangular cavities with varying relative dimensions at subsonic and transonic speeds. Cavities were tested with width-to-depth ratios of 1, 4, 8, and 16 for length-to-depth ratios l/h of 1 through 17.5. The maximum cavity depth was 2.4 in., and the turbulent boundary layer approaching the cavity was approximately 0.5 in. thick. Unsteady- and mean static-pressure measurements were made at free-stream Mach numbers from 0.20 to 0.95 at a unit Reynolds number per foot of approximately 3 x 10(exp 6); however, only unsteady-pressure results are presented in this paper. Results indicate that as l/h increases, cavity flows changed from resonant to nonresonant with resonant amplitudes decreasing gradually. Resonant spectra are obtained largely in cavities with mean static-pressure distributions characteristic of open and transitional flows. Resonance sometimes occurred for closed flow. Increasing cavity width or decreasing cavity depth while holding l/h fixed had the effect of increasing resonant amplitudes and sometimes induced resonance. The effects due to changes in width are more pronounced. Decreasing Mach number has the effect of broadening the resonances.

Tracy, Maureen B.↗
NASA NTRS1996

Non-linear k-epsilon-v(sup 2)(bar) modeling with application to high-lift

The k-epsilon-v(sup 2)(bar) model has been investigated to quantify its predictive performance on two high-lift configurations: 2D flow over a single-element aerofoil, involving closed-type separation; 3D flow over a prolate spheroid, involving open-type separation. A 'code-friendly' modification has been proposed which enhances the numerical stability, in particular, for explicit and uncoupled flow solvers. As a result of introducing Reynolds-number dependence into a coefficient of the s-equation, the skin-friction distribution for the by-pass transitional flow over a flat plate is better predicted. In order to improve deficiencies arising from the Boussinesq approximation, a nonlinear stress-strain constitutive relation was adopted, in which the only one free constant is calibrated on the basis of DNS data, and the Reynolds-stress anisotropy near the wall is fairly well represented.

Lien, F. S.↗
NASA NTRS1993

Thermally-Choked Combustor Technology

A program is underway to demonstrate the practical feasibility of thermally-choked combustor technology with particular emphasis on rocket propulsion applications. Rather than induce subsonic to supersonic flow transition in a geometric throat, the goal is to create a thermal throat by adding combustion heat in a diverging nozzle. Such a device would have certain advantages over conventional flow accelerators assuming that the pressure loss due to heat addition does not severely curtail propulsive efficiency. As an aid to evaluation, a generalized one-dimensional compressible flow analysis tool was constructed. Simplified calculations indicate that the process is fluid dynamically and thermodynamically feasible. Experimental work is also being carried out in an attempt to develop, assuming an array of practical issues are surmountable, a practical bench-scale demonstrator using high flame speed H2/O2 combustibles.

Knuth, William H.↗
NASA NTRS1995

A k-Omega Turbulence Model for Quasi-Three-Dimensional Turbomachinery Flows

A two-equation k-omega turbulence model has been developed and applied to a quasi-three-dimensional viscous analysis code for blade-to-blade flows in turbomachinery. the code includes the effects of rotation, radius change, and variable stream sheet thickness. The flow equations are given and the explicit runge-Kutta solution scheme is described. the k-omega model equations are also given and the upwind implicit approximate-factorization solution scheme is described. Three cases were calculated: transitional flow over a flat plate, a transonic compressor rotor, and transonic turbine vane with heat transfer. Results were compared to theory, experimental data, and to results using the Baldwin-Lomax turbulence model. The two models compared reasonably well with the data and surprisingly well with each other. Although the k-omega model behaves well numerically and simulates effects of transition, freestream turbulence, and wall roughness, it was not decisively better than the Baldwin-Lomax model for the cases considered here.

Chima, Rodrick V.↗
NASA NTRS1988

Studies of aerothermal loads generated in regions of shock/shock interaction in hypersonic flow

Detailed measurements of heat transfer and pressure distribution have been made in the present study of the aerothermal characteristics of regions of two-dimensional shock/shock interaction generated by the incidence of single and multiple shocks onto the bow shock ahead of a spanwise cylinder. For transitional flows, the measurements demonstrated a large increase in the aerothermal loads with increasing Mach number that cannot be predicted by simple phenomenological models. The studies with multiple incident shocks demonstrate that the largest aerothermal loads are generated on the cylinder when the shocks coalesce before they are incident on the bow shock.

Holden, M. S.↗
NASA NTRS1986

Aerothermal tests of spherical dome protuberances on a flat plate at a Mach number of 6.5

Aerothermal tests were conducted in the Langley 8-Foot High-Temperature Tunnel at a Mach number of 6.5 on a series of spherical dome protuberances mounted on a flat-plate test apparatus. Detailed surface pressure and heating-rate distributions were obtained for various dome heights and diameters submerged in both laminar and turbulent boundary layers including a baseline geometric condition representing a thermally bowed metallic thermal protection system (TPS) tile. The present results indicated that the surface pressures on the domes were increased on the windward surface and reduced on the leeward surface as predicted by linearized small-perturbation theory, and the distributions were only moderately affected by boundary-layer variations. Surface heating rates for turbulent flow increased on the windward surface and decreased on the leeward surface similar to the pressure; but for laminar boundary layers, the heating rates remained high on the leeward surface, probably due to local transition. Transitional flow effects cause heat load augmentation to increase by 30 percent for the maximum dome height in a laminar boundary layer. However, the corresponding augmentation for a dome with a height of 0.1 in. and a diameter of 14 in. representative of a bowed TPS tile was 14 percent or less for either a laminar or turbulent boundary layer.

Glass, C. E.↗
NASA NTRS2023

Experimental Characterization of the Space Launch System Block 1B Liftoff and Transition Environment

A wind tunnel test was conducted at the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel to evaluate the liftoff and transition flow environment of the Space Launch System Block 1B launch vehicles and tower interference effects with the newly designed Mobile Launcher 2. This test leveraged several unique diagnostic capabilities, including eight distributed force and moment measurements on the launch tower tiers, new umbilical and crew access arm configurations, and unsteady pressure acquisition on the rocket nose in the cargo configuration. The tower loading revealed a strong impact of the SLS vehicle height on force coefficients for individual tiers. Although the umbilicals produced weak influence on the loading on both vehicle and launch tower, unsteady pressure measurements revealed a slight increase in fundamental pressure oscillation frequency at specific wind azimuth directions. Multimodal flow states were observed in the gap flow between the vehicle and solid rocket boosters, producing different load profiles along the vehicle that are now incorporated in the vehicle database. This phenomenon was investigated using time-series measurements of forces as well as tufts and smoke flow visualization.

SLS↗
NASA NTRS1996

DSMC simulations of OREX entry conditions

Results of direct simulation Monte Carlo (DSMC) solutions are presented for the Japanese Orbital Reentry Experiment (OREX) vehicle, a 50 deg half-angle spherically blunted cone with a nose radius of 1.35 m and a base diameter of 3.4 m. The flow conditions simulated are those for entry into the Earth's atmosphere at a nominal velocity of about 7.4 km/s and zero incidence. Calculations are made for the higher altitude portion of entry, encompassing the transitional flow regime (altitudes of 200 to 80 km). Comparisons with flight measured values are made for axial acceleration, surface pressure, and stagnation point heating.

Moss, James N.↗
NASA NTRS1959

Heat Transfer from Cylinders in Transition From Slip Flow to Free-Molecule Flow

Over 600 measured heat-transfer coefficients in the transition from slip to free-molecule flow have been correlated by using the Nusselt number Nu as a function of the Knudsen Kn and Reynolds Re (or Mach M) numbers. The experimental range for these heat-transfer data from transverse cylinders in air corresponds to the following dimensionless groups: M, 0.10 to 0.90; Re, 0.03 to 11.5; Kn, 0.10 to 5.0. The total air temperature T(sub t) was maintained constant at 80 F, but wire temperature was Varied from 150 to 580 F. At Kn=0.10, Nu extrapolates smoothly into slip-flow empirical curves that show Nu as a function of Re and M or Kn. The correlation gradually changes from the square root of Re(sub t) dependence characteristic of continuum flow to first-power Re dependence as Kn increases (decreasing Re). At the experimental limit Kn ft 5.0, the Nu data correlate with a mean fractional error of 413 percent by the prediction of free-molecule-flow theory. In comparing experimental results with theory, an accommodation coefficient of 0.57+/-0.07 was inferred from the heat-transfer data, which were obtained with etched tungsten wire in air. The wire recovery temperature T(sub e) was measured and compared with existing data and theory in terms of a ratio eta(equivalent to T(sub e)/T(sub t). The results can be divided into three groups by Kn criteria: For Kn less than 2.01, eta is independent of Kn, and eta decreases from 1.0 to 0.97 as M increases from 0 to 0.90; for 2.0 less than Kn less than 5.0, eta is a function of both Kn and M in this transition region to fully developed free-molecule flow; and for Kn greater than 5.0, eta predicted by free-molecule-flow theory is observed and increases from 1.0 to 1.08 as M increases from 0 to 0.90, again independent of Kn. Therefore, these T(sub e) data provide a guide to the boundary of fully developed free-molecule flow, which is.inferred from this research to exist for Kn greater than 5.0. This boundary criterion is substantiated by other published data on T(sub e) at supersonic speeds.

Cybulski, Ronald J.↗
NASA NTRS1991

Numerical analysis of rarefied slit flows. II - Navier-Stokes simulations

The model problem of pressure-driven flow of a rarefied monatomic gas through a two-dimensional slit is analyzed via full Navier-Stokes numerical simulation. Parametric solutions are generated for slit-height based Knudsen number ranging from continuum to transitional flow and for reservoir pressure ratios leading to subsonic and supersonic flow. The change in the structure of the flowfield near the slit as a function of pressure ratio and Knudsen number are quantified from a purely continuum standpoint. The choice of numerical domain size, boundary conditions and treatment of the slit are also discussed. As expected, comparison with a Direct Simulation Monte Carlo solution for a highly rarefied case shows large differences in the predicted mass flow. The cause of these differences can be quantified through detailed comparison of the local flowfield properties. For the larger pressure ratio cases qualitative trends with increasing rarefaction are discussed, including the change in the sonic line shape in the slit and the in total mass flow.

Wadsworth, D. C.↗
NASA NTRS2009

NEXT Long-Duration Test Neutralizer Performance and Erosion Characteristics

The NASA's Evolutionary Xenon Thruster (NEXT) program is developing the next-generation ion propulsion system with significant enhancements beyond the state-of-the-art to provide future NASA science missions with enhanced capabilities at a low total development cost. A Long-Duration Test (LDT) was initiated in June 2005, to verify the NEXT propellant throughput capability to a qualification-level of 450 kg, 1.5 times the anticipated throughput requirement of 300 kg per thruster based on mission analyses. As of September 2, 2009, the thruster has accumulated 24,400 hr of operation with extensive durations at the following input powers: 6.9, 4.7, 1.1, and 0.5 kW. The thruster has processed 434 kg of xenon, surpassing the NASA Solar Technology Application Readiness (NSTAR) program thruster propellant throughput demonstrated during the extended life testing of the Deep Space 1 flight spare ion thruster and approaching the NEXT development qualification throughput goal of 450 kg. The NEXT LDT has demonstrated a total impulse of 16.1 10(exp 6zzz0 N s; the highest total impulse ever demonstrated by an ion thruster. A reduction in neutralizer flow margin has been the only appreciable source of thruster performance degradation. The behavior of the neutralizer is not easily predicted due to both erosion and deposition observed in previous wear tests. Spot-to-plume mode transition flow data and in-situ erosion results for the LDT neutralizer are discussed. This loss of flow margin has been addressed through a combination of a design change in the prototype-model neutralizer to increase flow margin at low emission current and to update the NEXT throttle table to ensure adequate flow margin as a function of propellant throughput processed. The new throttle table will be used for future LDT operations. The performance of the NEXT LDT neutralizer is consistent with that observed for long-life hollow cathodes. The neutralizer life-limiting failure modes are progressing as expected and the neutralizer data indicate none of the neutralizer failures are imminent.

Herman, Daniel A.↗
NASA NTRS2018

DNS of Laminar to Turbulent Transition on NACA 0012 Airfoil with Sand Grain Roughness

The Lattice-Boltzmann-based solver PowerFLOW is used to perform direct numerical simulations of the transitional flow over an airfoil at Reynolds number equal to 0.657 million. The leading edge of the airfoil is covered with sand particles, represented by polyhedra, to mimic the grit used in experiments. The sensitivity of the laminar to turbulent transition to the size of these particles, grid resolution, spanwise length is evaluated and rectangular trips are also tested.

Ribeiro, A. F. P.↗
NASA NTRS1980

Investigations of eddy coherence in jet flows

In turbulent shear flow the term coherent structures refers to eddies which are both spatially coherent, i.e., large eddies, aand also temporally coherent, i.e., they retain their identities for times which are long compared with their time scales in fixed point measurements. In transitional flows, the existence of such structures is evident from flow visualizations. In many other flows, such structures are not so evident. The reasons for the existence of these two classes of flows are discussed and attention is focused upon the more difficult flows, where coherent structures are not so evident. Techniques by which the existence (or nonexistence) of such structures in these flows can be established from point measurements, are also discussed. A major problem is shown to be the need to discriminate between real losses in eddy coherence and apparent losses in coherence introduced by phase scrambling effects which 'smear' multipoint correlations. The analysis of multiprobe time dependent data in cold and reacting round turbulent jets is described and it is shown how evidence of strong eddy coherence can be extracted from data.

Yule, A. J.↗
NASA NTRS1990

One- and two-dimensional Stirling machine simulation using experimentally generated flow turbulence models

Investigations of one- and two-dimensional (1- or 2-D) simulations of Stirling machines centered around experimental data generated by the U. of Minnesota Mechanical Engineering Test Rig (METR) are covered. This rig was used to investigate oscillating flows about a zero mean with emphasis on laminar/turbulent flow transitions in tubes. The Space Power Demonstrator Engine (SPDE) and in particular, its heater, were the subjects of the simulations. The heater was treated as a 1- or 2-D entity in an otherwise 1-D system. The 2-D flow effects impacted the transient flow predictions in the heater itself but did not have a major impact on overall system performance. Information propagation effects may be a significant issue in the simulation (if not the performance) of high-frequency, high-pressure Stirling machines. This was investigated further by comparing a simulation against an experimentally validated analytic solution for the fluid dynamics of a transmission line. The applicability of the pressure-linking algorithm for compressible flows may be limited by characteristic number (defined as flow path information traverses per cycle); this warrants further study. Lastly the METR was simulated in 1- and 2-D. A two-parameter k-w foldback function turbulence model was developed and tested against a limited set of METR experimental data.

Goldberg, Louis F.↗
NASA NTRS1992

In-flight detection of flow separation, stagnation, and transition

Flight tests were conducted to demonstrate the feasibility of simultaneous determination of: (1) boundary-layer instability and transition characteristics; (2) flow separation region; and (3) the location of the leading-edge stagnation point. Surface mounted, multi-element, micro-thin, hot-film sensors were used in conjunction with a bank of constant-temperature anemometers and a PC-based 8-channel simultaneous data acquisition system. Conventional techniques were used to determine the boundary-layer instability and transition characteristics while the flow separation and the stagnation points were determined through the presence of phase reversal signatures.

Mangalam, S. M.↗
NASA NTRS1987

Direct simulation of stagnation streamline flow for hypersonic reentry

The direct simulation Monte Carlo (DSMC) method is applied to simulate one-dimensional flow along the stagnation streamline. The freestream conditions considered are those encountered by the nose region of the Space Shuttle Orbiter during the hypersonic reentry. The range of altitudes (75 to 92 km) considered in the present calculations covers continuum to the less rarefied portion of the transition flow regime. The calculations account for thermal as well as the chemical nonequilibrium effects. The attention is focused on the flow structure along the stagnation streamline for different specified shock locations at a given altitude. The effect of shock location on the stagnation-point gas composition and heat transfer is analyzed for specific altitude; consequently, these results are appropriate for hemispherical bodies with different nose radii. Finally, comparison is made between the present DSMC results and the viscous shock-layer calculations, which show good agreement at the lowest altitude.

Dogra, Virendra K.↗
NASA NTRSDate not supplied

Simulation and Modeling of Hypersonic Turbulent Boundary Layers Subject to Favorable Pressure Gradients due to Streamline Curvature

Direct numerical simulations (DNS) of favorable-pressure-gradient turbulent boundary layers are presented for a nominal freestream Mach number of 5, with the objective of assessing the limitations of the currently available Reynolds-averaged Navier-Stokes (RANS) models. The favorable pressure gradient is induced by the streamwise curvature of the two-dimensional, planar, convex measurement surface used during experiments at the Texas A&M University. The DNS data shows good comparison with the measured velocity profiles, strain rates, and some, but not all, of the Reynolds-stress components. The discrepancies between the predicted and the measured wall-normal as well as shear stress components are primarily attributed to the lower than actual values inferred from typical PIV measurements of turbulent boundary layers. The DNS data shows a zero or slightly negative Reynolds shear stress in the outer part of the boundary-layer, which is indicative of the decaying turbulent motion under a strong favorable pressure gradient. The DNS data is also compared with the results of RANS computations based on commonly used zero, one, and two equation eddy-viscosity models. The RANS models yield reasonable comparisons with the DNS-based skin friction under zero and weak pressure gradients, but significant discrepancies under a strong pressure gradient. The k-w SST model provided the best overall predictions of skin friction, except in the region where the flow transitions from a favorable to an adverse pressure gradient. While the RANS models examined herein also give good predictions of the Reynolds shear stress under a sufficiently weak pressure gradient, none of those models are able to appropriately capture the reduction in the Reynolds stresses when the flow was subjected to a strong pressure gradient. An a priori assessment of the turbulent heat-flux prediction based on the assumption of a constant turbulent Prandtl number with the DNS data shows that while the constant turbulent Prandtl number model is effective in predicting the wall-normal component of turbulent heat flux, it does not capture the turbulent heat transfer in the streamwise direction for all the pressure gradient cases. The failure of the constant turbulent Prandtl number model highlights a requirement for more advanced models of the turbulent heat flux.

turbulent boundary layers↗