Search NASA⌕ Search

SEARCH · Search NASA

Results for “Turbulent boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Measurement and correlation of aerodynamic heating to surface corrugation stiffened structures in thick turbulent boundary layers

The flow conditions for which heating distributions were measured on corrugated surfaces and wavy walls in turbulent boundary layers are shown, along with the ratio of the displacement thickness to the roughness height versus the local edge Mach number for an equivalent smooth surface. The present data are seen to greatly extend the range of data available on corrugated surfaces in turbulent boundary layers. These data were obtained by testing fullscale corrugation roughened panels in the wall boundary layer of a supersonic and hypersonic wind tunnel. The experimental program used to obtain the data is described. The data are analyzed and correlated in terms of the pertinent flow and geometric parameters. The developed correlations are compared with the available thin boundary layer data, as well as with previously published correlation techniques.

Brandon, H. J.↗
NASA NTRS1986

Coherent structures in a turbulent boundary layer. I - Generation of 'artificial' bursts

In an effort to better understand the physics and structure of coherent events in a turbulent boundary layer, an attempt is made to produce 'artificial' bursts. These are generated in a turbulent boundary layer developed on a flat plate towed in an 18 m water channel and thus with negligible freestream turbulence. The burstlike events are produced by either withdrawing near-wall fluid from two minute holes separated in the spanwise direction or by pitching a miniature delta wing that is flush-mounted to the wall. Either of these two actions generates a hairpinlike vortex and low-speed streak that resemble naturally occurring structures. The resulting sequence of events that occur at a given location can be uniquely controlled, thus allowing detailed examination via phase-locked measurements and flow visualization. In this paper, the proof of concept of artificial burst generation is established by comparing the artificial events with natural, random bursts using flow visualization and hot-film signals.

Gad-El-hak, M.↗
NASA NTRS1972

Prediction of local and integrated heat transfer in nozzles using an integral turbulent boundary layer method

An empirical modification of an existing integral energy turbulent boundary layer method is proposed in order to improve the estimates of local heat transfer in converging-diverging nozzles and consequently, provide better assessments of the total or integrated heat transfer. The method involves the use of a modified momentum-heat analogy which includes an acceleration term comprising the nozzle geometry and free stream velocity. The original and modified theories are applied to heat transfer data from previous studies which used heated air in 30 deg - 15 deg, 45 deg - 15 deg, and 60 deg - 15 deg water-cooled nozzles.

Boldman, D. R.↗
NASA NTRS1984

The effect of a short region of concave curvature on a supersonic turbulent boundary layer

Mean flow measurements have been made in a supersonic turbulent boundary layer experiencing a short region of concave curvature and an adverse pressure gradient. The incoming boundary layer had a Mach number of 2.87 and a unit Reynolds number of 6.3 x 10 to the 7th/m. Flow over constant radii curvatures of delta (0)/R = 0.10 and 0.02 with a fixed turning angle of 8 deg were investigated. Results indicate that both flows remain two-dimensional; length scales increase over their equilibrium values; the mean flow behaves similarly to subsonic flows experiencing concave curvature and lateral divergence; and boundary layer behavior is strongly similar to a corresponding 8 deg ramp flow.

Smits, A. J.↗
NASA NTRS1982

Pointwise and scanning laser anemometer measurements in steady and unsteady separated turbulent boundary layers

The physical features of steady and unsteady freestream separating turbulent boundary layers that have been determined by pointwise laser anemometer measurements are outlined. It is seen that the large-scale structures control the outer region's backflow behavior. Near the wall, the mean backflow velocity profile for both the steady and unsteady cases is found to scale on the maximum negative mean velocity and its distance from the wall. A description is given of a scanning laser anemometer that produces nearly instantaneous velocity profiles for examing the temporal features of these large-scale structures. Also described is a 'zero-wake' seeder that supplies particles to the outer shear layer and freestream flow with a minimal disturbance.

Simpson, R. L.↗
NASA NTRS1991

An exploratory study of a three-dimensional shock wave turbulent boundary layer interaction in a corner

Three-dimensional shock wave turbulent boundary layer interactions in a corner have been studied at M about 3. The first phase, detailed mean wall static pressure distributions, has shown the interaction of a two-dimensional flow on one wall with the three-dimensional flow generated by a fin. Major three-dimensional effects on both flows were observed, extending from the interaction of the initial region of the three-dimensional flow and the corner. A large part of the resulting corner flow has little resemblance to either the two-dimensional or three-dimensional interacting flows.

Bogdonoff, S. M.↗
NASA NTRS2014

Direct Numerical Simulations of High-Speed Turbulent Boundary Layers over Riblets

Direct numerical simulations (DNS) of spatially developing turbulent boundary layers over riblets with a broad range of riblet spacings are conducted to investigate the effects of riblets on skin friction at high speeds. Zero-pressure gradient boundary layers under two flow conditions (Mach 2:5 with T(sub w)/T(sub r) = 1 and Mach 7:2 with T(sub w)/T(sub r) = 0:5) are considered. The DNS results show that the drag-reduction curve (delta C(sub f)/C(sub f) vs l(sup +)(sub g )) at both supersonic speeds follows the trend of low-speed data and consists of a `viscous' regime for small riblet size, a `breakdown' regime with optimal drag reduction, and a `drag-increasing' regime for larger riblet sizes. At l l(sup +)(sub g) approx. 10 (corresponding to s+ approx 20 for the current triangular riblets), drag reduction of approximately 7% is achieved at both Mach numbers, and con rms the observations of the few existing experiments under supersonic conditions. The Mach- number dependence of the drag-reduction curve occurs for riblet sizes that are larger than the optimal size, with smaller slopes of (delta C(sub f)/C(sub f) for larger freestream Mach numbers. The Reynolds analogy holds with 2(C(sub h)=C(sub f) approximately equal to that of at plates for both drag-reducing and drag-increasing configurations.

Duan, Lian↗
NASA NTRS1974

Interference heating from interactions of shock waves with turbulent boundary layers at Mach 6

An experimental investigation of interference heating resulting from interactions of shock waves and turbulent boundary layers was conducted. Pressure and heat-transfer distributions were measured on a flat plate in the free stream and on the wall of the test section of the Langley Mach 6 high Reynolds number tunnel for Reynolds numbers ranging from 2 million to 400 million. Various incident shock strengths were obtained by varying a wedge-shock generator angle (from 10 deg to 15 deg) and by placing a spherical-shock generator at different vertical positions above the instrumented flat plate and tunnel wall. The largest heating-rate amplification factors obtained for completely turbulent boundary layers were 22.1 for the flat plate and 11.6 for the tunnel wall experiments. Maximum heating correlated with peak pressures using a power law with a 0.85 exponent. Measured pressure distributions were compared with those calculated using turbulent free-interaction pressure rise theories, and separation lengths were compared with values calculated by using different methods.

Johnson, C. B.↗
NASA NTRS1973

The behavior of a compressible turbulent boundary layer in a shock-wave-induced adverse pressure gradient

The results of an experimental investigation of the mean- and fluctuating-flow properties of a compressible turbulent boundary layer in a shock-wave-induced adverse pressure gradient are presented. The turbulent boundary layer developed on the wall of an axially symmetric nozzle and test section whose nominal free-stream Mach number and boundary-layer thickness Reynolds number were 4 and 100,000, respectively. The adverse pressure gradient was induced by an externally generated conical shock wave. Mean and time-averaged fluctuating-flow data, including the complete experimental Reynolds stress tensor and experimental turbulent mass- and heat-transfer rates are presented for the boundary layer and external flow, upstream, within and downstream of the pressure gradient. The mean-flow data include distributions of total temperature throughout the region of interest. The turbulent mixing properties of the flow were determined experimentally with a hot-wire anemometer. The calibration of the wires and the interpretation of the data are discussed. From the results of the investigation, it is concluded that the shock-wave - boundary-layer interaction significantly alters the turbulent mixing characteristics of the boundary layer.

Rose, W. C.↗
NASA NTRS1972

Heat transfer to the transpired turbulent boundary layer.

This paper contains a summarization of five years work on an investigation on heat transfer to the transpired turbulent boundary layer. Experimental results are presented for friction coefficient and Stanton number over a wide range of blowing and suction for the case of constant free-stream velocity, holding certain blowing parameters constant. The problem of the accelerated turbulent boundary layer with transpiration is considered, experimental data are presented and discussed, and theoretical models for solution of the momentum equation under these conditions are presented. Data on turbulent Prandtl number are presented so that solutions to the energy equation may be obtained. Some examples of boundary layer heat transfer and friction coefficient predictions are presented using one of the models discussed, employing a finite difference solution method.

Kays, W. M.↗