SEARCH · Search NASA

Results for “Widely Used”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Hydrogen Production System Scaling Using a High-Fidelity Simulation-Optimization Framework

Proton exchange membrane (PEM) electrolyzers are widely used for hydrogen production, yet few validated, high-fidelity tools can reliably guide scale-up. Using measured performance from a 50-hour hardware-in-the-loop pilot test, a physics-based, plant-level model of a 1.25 MW PEM electrolyzer and its balance-of-plant (BoP) subsystems is developed and validated. The model couples electrochemistry and thermal/flow submodels and is calibrated against pilot test data via a genetic algorithm (GA) workflow. Validation yields a mean absolute percentage error (APE) of 0.43% for cell voltage and stack power. Two scale-out strategies are then benchmarked under a common 7-day wind-and-photovoltaic (PV) profile: (i) linear duplication of 1.25 MW blocks and (ii) shared-BoP architectures. Sharing BoP between stacks reduces BoP energy by 27% at 10 MW and 34% at 100 MW (vs. linear duplication) and improves system specific energy consumption (SEC) to 52.9 and 52.6 kWh/kg, respectively (from 54.0 kWh/kg with linear duplication). Partial-load studies (25-100% set-point) show that cumulative hydrogen production remains nearly constant down to 50% load because all cases use the same weekly renewable-energy input. Below 50%, the power cap limits how much energy can be used within 168 h, which reduces hydrogen output. The model further indicates that the practical operating optimum lies between 50% and 85% load, where efficiency gains begin to appear without significant loss in hydrogen output. Moreover, the efficiency gains at lower loads are offset by reduced production. The validated framework supports scenario-based engineering trade-off studies for large configurations (10-100 MW) and for operating policies under variable renewables.

08 HYDROGEN↗

DOE OSTI2025

Palm oil deoxygenation with glycerol as a hydrogen donor for renewable fuel production using nickel-molybdenum catalysts: The effect of support

Palm oil, one of the most widely used vegetable oils, offers significant potential as a sustainable feedstock for biofuel production. This study explores the deoxygenation of palm oil using glycerol as a hydrogen donor, with nickel-molybdenum (NiMo) catalysts supported on commercial alumina (Al 2 O 3 ), and zeolite (HZSM-5) comparing with self-prepared zirconia (ZrO 2 ). The catalysts were synthesized via incipient wetness impregnation and evaluated for their performance in biofuel production. NiMo/Al 2 O 3 exhibited the lowest oxygen removal efficiency (68.5 %), while NiMo/HZSM-5 achieved a higher oxygen removal (74.3 %) but also demonstrated the highest coke formation. The type of support material influenced the resulting biofuel range, with NiMo/HZSM-5 and NiMo/ZrO 2 favoring jet fuel production, whereas NiMo/Al 2 O 3 was more suitable for diesel production. Notably, NiMo/ZrO 2 exhibited the highest performance in palm oil deoxygenation while minimizing coke formation. These findings highlight NiMo/ZrO 2 as a promising catalyst for efficient and stable biofuel production, with the support material significantly influencing product yield and fuel quality.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Probing Conformational Evolution and Associated Dynamics of Mg(N(SO 2 CF 3 ) 2 ) 2 ·Dimethoxyethane Adduct Using Solid-State 19 F and 1 H NMR

Bis(trifluoromethanesulfonimide) or TFSI is widely used as a counter anion in electrolyte design due to its structural flexibility and chemical stability. Here we studied the conformational variations and associated dynamics of TFSI in adduct of Mg(TFSI) 2 with dimethoxyethane (DME), a solvate crystalline material using solid-state 1 H and 19 F NMR. TFSI molecular motion in this solvate structure falls within the timescale of the 19 F NMR experiment, yielding spectroscopic signatures for unique TFSI conformers under the coordination environment of Mg 2+ cation. Within the temperature range of -5 to 82 °C, we observe nine distinct TFSI sites in both crystalline and disordered regions using 19 F NMR, reflecting complexity of structural and dynamics of TFS1 anions within solvate structure. The four distinguishable sites in the disordered region for the two CF 3 groups of the same TFSI molecule are identified using chemical shift analysis. The exchange rate constants from site to site are calculated through variable temperature 19 F NMR and two-dimensional (2D) exchange spectroscopy (EXSY) experiments, along with respective activation enthalpies using Eyring's formulation. The flip rate of CF 3 around the S-C bond is estimated as ~ 15 s -1 at 8 °C with ΔH ≠ ~ 22 kJ/mol, but the rotation of the entire TFSI is 4.8 s -1 at 8 °C with a significantly greater ΔH ≠ = 98 ± 10 kJ/mol. Furthermore, the slow conversion of trans to cis conformers at a lower temperature (T ≤ 1 °C) in the crystalline region is monitored, with a conversion rate of ~ 2 x 10 -5 s -1 at -5 °C. Density functional theory (DFT)-based calculations were performed to support further the assignment of experimental chemical shifts, and the activation energy E a = 21.1 kJ/mol obtained for the cis to trans transition is consistent with experimental values. The combined set of 19 F and 1 H under both one-dimensional (1D) and 2D NMR methods demonstrated here can be further used for examining electrode-electrolyte interfaces to probe the motions of various constituents that can enable detailed studies of interfacial processes and dynamics. Ultimately, such studies will aid in the design and discovery of interfacial constructs in which directed defect chemistry, chemical moiety distribution, and nanostructure are employed to drive efficient charge transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

kokkosSZ (kSZ) A Portable Cellerator Implementation of SZ using Kokkos Programming Model

kSZ is a Kokkos-based implementation of the world-widely used SZ lossy compressor. We use Kokkos because it provides abstractions for both parallel execution of code and data management, which can be used to support portable implementation across different accelerator technologies. Kokkos can support OpenMP/OpenMPTarget, oneAPI, Pthreads, and CUDA as backend programming models.

ECP↗

DOE OSTI2021

Classification of Semiconductors Using Photoluminescence Spectroscopy and Machine Learning

Photoluminescence spectroscopy is a nondestructive optical method that is widely used to characterize semiconductors. In the photoluminescence process, a substance absorbs photons and emits light with longer wavelengths via electronic transitions. This paper discusses a method for identifying substances from their photoluminescence spectra using machine learning, a technique that is efficient in making classifications. Neural networks were constructed by taking simulated photoluminescence spectra as the input and the identity of the substance as the output. Here, six different semiconductors were chosen as categories: gallium oxide (Ga 2 O 3 ), zinc oxide (ZnO), gallium nitride (GaN), cadmium sulfide (CdS), tungsten disulfide (WS 2 ), and cesium lead bromide (CsPbBr 3 ). The developed algorithm has a high accuracy (>90%) for assigning a substance to one of these six categories from its photoluminescence spectrum and correctly identified a mixed Ga 2 O 3 /ZnO sample.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

PtCo/MWCNTs Prepared by a Microwave‐assisted Polyol Method for Selective Cinnamaldehyde Hydrogenation

Abstract Using microwave irradiation, PtCo alloy nanoparticles were deposited within a few minutes on COOH‐functionalized MWCNT supports. The obtained catalysts were used for selective hydrogenation of cinnamaldehyde, a reaction whose products are widely used in various fields. In the selective cinnamaldehyde hydrogenation to cinnamyl alcohol, microwave‐prepared catalysts (generically, Pt x Co y ‐MW) outperformed a catalyst prepared by the conventional method (Pt 1 Co 2 ‐con). The highest selective hydrogenation to cinnamyl alcohol, 89%, was obtained using Pt 1 Co 2 ‐MW, while Pt 1 Co 2 ‐con showed a selectivity of 76%. Characterization results confirmed that the microwave prepared samples had a stronger interaction between Pt and Co than that in the Pt 1 Co 2 ‐con sample. The alloyed Co altered the electronic structure of Pt, leading to favorable adsorption of the C=O bond by the lone‐pair electrons of its oxygen atom. Moreover, the Pt 1 Co 2 ‐MW sample showed neglectable change in catalytic performance (e. g., cinnamaldehyde conversion and selective hydrogenation to cinnamyl alcohol) during recycling experiments.

Wang, Kaiying↗

DOE OSTI2024

Assessing the Sensitivity of Pourbaix Diagrams to Computational Protocols: Electrochemical Stability of Ni Oxides as a Case Study

Pourbaix diagrams stand as a useful tool in assessing and visualizing materials’ electrochemical stability and are widely used for electrocatalyst design. However, their reliability hinges on the accuracy of the chemical potentials of involved phases, which may bear uncertainties and can be significantly impacted by decision-making steps in the computational protocol. Here, this study introduces a robust sensitivity analysis framework, exemplified through a detailed examination of the computational Pourbaix diagram of Ni, the oxides of which are used as high-activity and cost-friendly catalysts for many electrochemical reactions. Quantities of interest derived from the Pourbaix diagram include the appearance and stability domain of the catalytically active Ni oxide phases along with the onset electrochemical potentials of phase transitions. These metrics can guide the design of operational conditions for Ni oxide electrocatalysts. We find that the employed DFT exchange-correlation functional has the most significant influence on the computed Pourbaix diagram. Uncertainties on crystal structures, along with their related ab initio energetics, are also found to affect the size of the phase stability domain. Higher-order coupling among input parameters is found to play a crucial role in influencing the appearance and distribution of Ni phases in the diagram. Our findings suggest a need to consider variations and uncertainties associated with the computational procedures on predicted Pourbaix diagrams for materials design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Single crystal growth of iridates without platinum impurities

Iridates have attracted much interest in the last decade for their novel magnetism emerging in the limit of strong spin-orbit coupling and possible unconventional superconductivity. A standard for growing iridate single crystals has been the flux method using platinum crucibles. Here, in this work, we show that this widely used method compromises the sample quality by inclusion of platinum impurities. We find that Sr 2 ⁢IrO 4 single crystals grown in iridium crucibles show remarkable differences from those grown in platinum crucibles in their sample characterizations using Raman spectroscopy, resistivity, magnetization, optical third harmonic generation, resonant x-ray diffraction, and resonant inelastic x-ray scattering measurements. In particular, we show that several peaks of sizable intensities disappear in the Raman spectra of samples free of platinum impurities, and a significantly larger activation energy is extracted from the resistivity data compared to previously reported values. Furthermore, we find no evidence of the previously reported glide-symmetry-breaking structural distortions and confirm the I⁢ 4 1 / acd space group of the lattice symmetry. Although the platinum impurities are not apparent in the magnetic properties and thus went unnoticed in the stoichiometric insulating phase for a long time, their effects can be much more detrimental to transport properties in chemically doped compounds. Therefore, our result suggests using growth methods that avoid platinum impurities for an investigation of the intrinsic physical properties of iridates, and possible superconducting phases.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Modeling and Control Using Stochastic Distribution Control Theory for Intersection Traffic Flow

In this work, we investigated stochastic distribution control theory-based traffic signal optimization to achieve a smooth and uniform flow of vehicles through signalized intersections. In this context, the static and linear dynamic stochastic distribution models were developed to express the relationship between the signal timing and the traffic queue length together with its probability density function. Two stochastic distribution control algorithms were designed to control the signal timing at intersections such that the probability density function of the traffic queue of each intersection road segment is made as narrow and as small as possible. Also, a recursive input-output traffic queue estimation model was proposed, which is data-driven and dynamic in nature, to calculate real-time traffic queue length using traffic signal timings and loop-detector data. The control algorithms were evaluated for a one-signal corridor, two-signal corridor, and 2 x 2 network of signalized intersections. MATLAB simulation examples are provided to demonstrate the use of the proposed algorithms and comparison to the existing widely-used semi-actuated control has been made. Desired results were obtained.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Robust measurement of microbial reduction of graphene oxide nanoparticles using image analysis

ABSTRACT Shewanella oneidensis ( S. oneidensis ) has the capacity to reduce electron acceptors within a medium and is thus used frequently in microbial fuel generation, pollutant breakdown, and nanoparticle fabrication. Microbial fuel setups, however, often require costly or labor-intensive components, thus making optimization of their performance onerous. For rapid optimization of setup conditions, a model reduction assay can be employed to allow simultaneous, large-scale experiments at lower cost and effort. Since S. oneidensis uses different extracellular electron transfer pathways depending on the electron acceptor, it is essential to use a reduction assay that mirrors the pathways employed in the microbial fuel system. For microbial fuel setups that use nanoparticles to stimulate electron transfer, reduction of graphene oxide provides a more accurate model than other commonly used assays as it is a bulk material that forms flocculates in solutions with a large ionic component. However, graphene oxide flocculates can interfere with traditional absorbance-based measurement techniques. This study introduces a novel image analysis method for quantifying graphene oxide reduction, showing improved performance and statistical accuracy over traditional methods. A comparative analysis shows that the image analysis method produces smaller errors between replicates and reveals more statistically significant differences between samples than traditional plate reader measurements under conditions causing graphene oxide flocculation. Image analysis can also detect reduction activity at earlier time points due to its use of larger solution volumes, enhancing color detection. These improvements in accuracy make image analysis a promising method for optimizing microbial fuel cells that use nanoparticles or bulk substrates. IMPORTANCE Shewanella oneidensis ( S. oneidensis ) is widely used in reduction processes such as microbial fuel generation due to its capacity to reduce electron acceptors. Often, these setups are labor-intensive to operate and require days to produce results, so use of a model assay would reduce the time and expenses needed for optimization. Our research developed a novel digital analysis method for analysis of graphene oxide flocculates that may be utilized as a model assay for reduction platforms featuring nanoparticles. Use of this model reduction assay will enable rapid optimization and drive improvements in the microbial fuel generation sector.

Bennett, Danielle T. (ORCID:0009000188748827)↗

DOE OSTI2023

Decarbonization of Liquid Heating Fuels

Annually, residential and commercial buildings use about 5 billion gallons (18.9 billion liters) of distillate fuel for space and water heating. There is considerable interest in decarbonizing these markets through a combination of heat pumps and a future, carbon-free grid. An alternate approach that offers rapid and cost effective decarbonization involves substitution of low-carbon biofuels for fossil fuels within this market. Heating fuel marketers in North America and Europe are aggressively moving to achieve market penetration of biofuels. Processes for this include fuel specification standards, development of manufacturer-approved burners and all system components, development of standards for equipment listing, installation code changes, and generation of performance data. There has been considerable progress in these areas and each of these are reviewed in this paper. Currently, the most important biofuel for this market is biodiesel with a U.S. production capacity of 2.4 billion gallons (9.1 billion liters) and approximately a 75% reduction in GHG emissions. The biodiesel industry has stated a vision for dramatic increases in biodiesel production over the next decades. Fuel and equipment standards are in place to enable use of biodiesel blends to 20% and this blend is now widely used. Standard changes to extend this to as high as 100% biodiesel are nearing completion. Several states have implemented requirements for minimum levels of biodiesel in heating oil with these levels increasing over time.

09 BIOMASS FUELS↗

DOE OSTI2024

Investigation of Correlation Methods for Use in Criticality Safety

Although their adoption by practitioners has been limited, the introduction of similarity indices in criticality safety was a major step forward in reducing the reliance on expert judgement in discerning applicable experiments for the validation of new appliations in criticality safety analyses. Similarity indices have been successfully employed in bias trending and data assimilation techniques, but it is often unclear which acceptance criteria should be used. In their 2004 paper, Broadhead et al. specify the most widely used similarity parameter, ck, as an acceptance cutoff at 0.9. (Broadhead et al., ”Sensitivity and Uncertainty-Based Criticality Safety Validation Techniques,” Nucl. Sci. Eng. 146, 340–366, 2004). Experiments with a ck < 0.9 are often not considered applicable for code validation. This heuristic is based on quantitative studies and engineering judgement, but in some cases, experiments with ck < 0.9 can be used to accurately estimate computational bias. This suggests that further analysis is needed to determine what components of ck are driving applicability and accuracy in bias estimation. For cases in which applicable experiments may not be available (as is the case with UF6 transport canisters), understanding what distinguishes experiments in providing adequate bias estimates aside from just the similarity index is particularly necessary. To further the goal to better interpret ck values, several visualization tools were developed to assist in the investigation of which components of ck are driving applicability.

ck↗

DOE OSTI2023

Use of Fluorescent Protein Reporters for Assessing and Detecting Genome Editing Reagents and Transgene Expression in Plants

Fluorescent protein reporters have been widely used for monitoring the expression of target genes in various engineered organisms. Although a wide range of analytical approaches (e.g., genotyping PCR, digital PCR, DNA sequencing) have been utilized to detect and identify genome editing reagents and transgene expression in genetically modified plants, these methods are usually limited to use in the late stages of plant transformation and can only be used invasively. Here we describe GFP- and eYGFPuv-based strategies and methods for assessing and detecting genome editing reagents and transgene expression in plants, including protoplast transformation, leaf infiltration, and stable transformation. These methods and strategies enable easy, noninvasive screening of genome editing and transgenic events in plants.

Yuan, Guoliang↗

DOE OSTI2022

Throughput-Oriented and Accuracy-Aware DNN Training with BFloat16 on GPU

Deep Neural Networks (DNNs) have transformed the field of artificial intelligence and achieved extraordinary success in many areas. The training of DNNs is commonly compute and memory-intensive, which has resulted in several optimizations in the training phase. Among them, reduced precision is a typical and widely used technique to accelerate DNN training and reduce memory requirements. However, applying a widely adopted reduced precision format such as Float16 to all involved operations in DNN training is not optimal as the use of Float16 in some operations can hurt model accuracy. Meanwhile, additional optimizations including loss scaling and autocast techniques can mitigate the accuracy loss but lead to inherent overhead and inadequate use of reduced precision. In this work, we leverage another reduced precision format, BFloat16, and introduce a throughput-oriented and accuracy-aware approach to maximize the performance potential of DNN training. Since the high throughput provided by BFloat16 format is accompanied by low precision of the floating-point representation, this approach achieves high throughput by using BFloat16 on all DNN operations and avoids the accuracy loss through a customized accuracy-aware normalization. Results show that our approach outperforms the state-of-the-art mixed-precision training by 1.21x on an NVIDIA A100 GPU.

Xie, Zhen↗

DOE OSTI2022

Effect of second Si–O vibrational overtones/combinations on quantifying water in silicate and silica minerals using infrared spectroscopy, and an experimental method for its removal

Infrared spectroscopy (IR) is the most widely used analytical tool to quantify trace water in silicate and silica minerals. A prerequisite for highly accurate IR measurements of trace water is a good understanding of the effect of the second Si–O vibrational overtones/combination bands (2nd Si–O VOCBs) on the water peaks. Silicate and silica minerals can be divided as isolated (Q 0 ), paired (Q 1 ), ring (Q 2 ), chain (Q 1 or Q 2 ), sheet (Q 3 ) and framework (Q 4 ) structures according to the polymerization of their SiO 4 tetrahedral units, and the 2nd Si–O VOCBs of these different structural types attain different vibrational features which are expected to affect the water peaks to different extents. Here, we selected olivine (Q 0 ) and α-quartz (Q 4 ) as two endmember-like structural examples, performed extensive IR measurements on both pristine and heat-treated thin sections prepared for these two minerals, and explored the vibrational features of the 2nd Si–O VOCBs. In this work, we have found that the 2nd Si–O VOCBs are well separated from the water peaks in olivine, but severely overlap with the water peaks in α-quartz, confirming the different roles that the 2nd Si–O VOCBs play in quantifying trace water in silicate and silica minerals with different structural polymerizations. To remove the influence of the 2nd Si–O VOCBs (or any other species rather than water), an experimental protocol has been successfully developed, as approved by some fundamental equations and verified by the data of α-quartz in the literature. This development should lead to significant accuracy improvement in quantifying trace amounts of water in Earth and planetary materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Studying drought-induced forest mortality using high spatiotemporal resolution evapotranspiration data from thermal satellite imaging

Drought can have pervasive and wide-spread impacts to forest health, as evidenced in several severe events occurring over the recent decades. Extensive forest die-off due to drought can impair the ecological functioning of forests, impacting habitat, water yield and quality from forested lands, and altering forest fire dynamics and intensity. Satellite remote sensing provides an effective means for detecting and monitoring spatial patterns of forest mortality over large areas, exploiting free and open long-term image archives available at a range in spatial and temporal resolutions. While remotely sensed surface reflectances and vegetation indices have been widely used to study optical response of forest canopies to drought events, retrievals of evapotranspiration (ET) derived from thermal satellite imagery – particularly at resolutions approaching crown scale - can provide insights into cumulative tree stresses that can incite disease and trigger mortality. In this study, we applied a multi-sensor satellite data fusion approach to estimate daily 30-m resolution ET and an associated Evaporative Stress Index (ESI) to study drought-induced mortality in a temperate forest at the Missouri Ozark AmeriFlux (MOFLUX) site, located in the central United States. The study covered the period from 2010 to 2014, including an exceptional drought year of 2012. Modeled ET agreed well with eddy flux measurements from the MOFLUX tower, with average monthly relative errors of 15%. Plot-scale ESI, describing temporal anomalies in the ratio of actual-to-reference ET, was used as an index of relative forest health to investigate relationships between forest mortality and drought severity. ESI showed good agreement with observed predawn leaf water potential, especially during the drought year. Furthermore, plot-scale ESI was also correlated with the subsequent year's tree mortality, suggesting the importance of considering the forest health condition prior to drought when studying drought-induced forest impacts. This study demonstrates the utility of multi-year ET remote sensing data at the stand or plot scale as an indicator of forest health and as a predictor of future mortality due to drought.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Aeroelastic code comparison using the IEA 22MW reference turbine

Reference wind turbine designs and the associated aeroelastic models are widely used in both research and industry. Reference models representing future concepts are of particular interest. Current state of the art aeroelastic tools are relied upon to design the next generation of large wind turbines. However, modelling assumptions may be invalidated by upcoming very large turbines, and different aeroelastic tools may give inconsistent results. A 22MW turbine model has been defined as part of International Energy Agency (IEA) Wind Task 55 on Reference Wind Turbines and Farms to represent future turbines to be deployed in the 2030s. In this study, an aeroelastic model of this turbine has been created in four tools; Bladed, HAWC2, OpenFAST, and QBlade. Code comparisons are presented for steady state operation, linear stability analysis, and time domain power production simulations in steady and turbulent wind. Generally, the codes show a good agreement, but with some differences present in the linear stability analysis, periodic azimuthal variation, and time domain simulations. The models are a good basis for further study with the IEA 22MW turbine, and further code comparison exercises.

17 WIND ENERGY↗

DOE OSTI2020

Prediction of gas hydrate saturation using machine learning and optimal set of well-logs

We report resistivity and acoustic logs are widely used to estimate gas hydrate saturation in various sedimentary systems using one of the two popular methods ((1) acoustic velocity and (2) electrical resistivity), but the limitations of these two methods are often overlooked, which include (i) well-specific calibration of empirical exponents in the electrical resistivity method, (ii) assumption of known pore morphology for gas hydrates in the acoustic velocity method, and (iii) presence of unknown mineralogy and bulk modulus terms in the acoustic velocity method. NMR-density porosity-derived gas hydrate saturation based on the analysis of the transverse magnetization relaxation time (T2) is considered the most precise method, but acquisition of NMR-based logs is limited at relatively recent drilled sites; additionally, its use in conventional oil and gas reservoirs is not that common due to higher cost and operational deployment limitations associated with acquiring NMR well-logs. This study proposes a new method that predicts gas hydrate saturation (S h ) for any well using porosity, bulk density, and compressional wave (P wave) velocity well-logs with neural network (or stochastic gradient descent regression) without any well-specific calibration and/or other aforementioned shortcomings of the existing methods. The method is developed by examining the underlying dependency between S h and different combinations of well-logs, chosen from 6 routine logs, with 12 different machine learning (ML) algorithms. The accuracy of the proposed method in predicting S h is ~ 84%, which is better than the accuracy of seismic and electrical resistivity methods (≤ 75%) per the results reported by three different studies. The robustness of the method in the specific case of permafrost-associated gas hydrates is demonstrated with well-log data from two wells drilled on the Alaska North Slope.

58 GEOSCIENCES↗