Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustic devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Surface and bulk two-level-system losses in lithium niobate acoustic resonators

Lithium niobate (LN) is a promising material for building acoustic resonators used in quantum applications, but its performance is limited by poorly understood material defects called two-level systems (TLSs). Here, in this work, we fabricate high-performance acoustic resonators from LN with quality factors up to 6 ×10 7 and use them to separate bulk and surface contributions to TLS loss. By comparing these bulk acoustic wave (BAW) resonators with previous surface-acoustic-wave and phononic-crystal studies, we show that devices with high surface-participation ratios are limited by surface TLSs, while our BAW devices reveal an intrinsic bulk TLS limit. Through systematic surface treatments and microscopy, we demonstrate that BAW resonator performance remains unchanged despite surface modifications, confirming operation in a bulk-limited regime. Here, our work establishes quantitative bounds on both surface and bulk TLS losses in LN within the context of the material growth and fabrication approaches we have pursued, and it provides guidance for future device engineering and materials development.

acoustic wave phenomena↗
NASA NTRS1981

Turbomachinery noise studies of the AiResearch QCGAT engine with inflow control

The AiResearch Quiet Clean General Aviation Turbofan engine was tested on a vertical lift fan facility to measure the acoustic performance of two inflow control devices (ICD) of similar design, and three inlet lips of different external shape. Far-field directivity patterns calculated by existing analyses were compared with the measured fan fundamental blade passing frequency (BPF/F/) and broadband data. Installing an ICD on an engine with hardwall ducts reduced the BPF(F) tone everywhere in the far-field. When the ICD was installed on an engine with active acoustic panels, tone reduction in the forward quadrant was comparable to that in the hardwall tests; in the aft quadrant, however, tone noise was attenuated by the large acoustic panels in the bypass duct to such a degree that the ICD had little effect. Tests to compare performance of ICDs with hardwall inlet ducts showed only minor differences in the BPF(F) directivity patterns, while broadband noise was the same for both. Forward-quadrant BPF(F) and broadband directivity patterns were found to be similar for the inlet lips tested with a hardwall inlet duct. At high fan speeds, however, the shape of the analytical multimodal tone pattern from the exhaust nozzle was flatter than the measured patterns. The sources of lobes from several propagating single modes found in the forward-quadrant BPF(F) data were attributed to rotor/strut interaction and the rotor-alone pressure field.

Mcardle, J. G.↗
NASA NTRS2008

Intelligent Engine Systems: Acoustics

An extensive study of new fan exhaust nozzle technologies was performed. Three new uniform chevron nozzles were designed, based on extensive CFD analysis. Two new azimuthally varying variants were defined. All five were tested, along with two existing nozzles, on a representative model-scale, medium BPR exhaust nozzle. Substantial acoustic benefits were obtained from the uniform chevron nozzle designs, the best benefit being provided by an existing design. However, one of the azimuthally varying nozzle designs exhibited even better performance than any of the uniform chevron nozzles. In addition to the fan chevron nozzles, a new technology was demonstrated, using devices that enhance mixing when applied to an exhaust nozzle. The acoustic benefits from these devices applied to medium BPR nozzles were similar, and in some cases superior to, those obtained from conventional uniform chevron nozzles. However, none of the low noise technologies provided equivalent acoustic benefits on a model-scale high BPR exhaust nozzle, similar to current large commercial applications. New technologies must be identified to improve the acoustics of state-of-the-art high BPR jet engines.

Wojno, John↗
DOE OSTI2023

Standoff inspection using geometry-informed full-wavefield response measurements

A vibrometer may measure acoustic responses in portions of a structure along a scan path to acoustic excitation of the structure. A ranging device may measure distances to the portions of the structure along the scan path. A three-dimensional point cloud may be generated based on the acoustic responses in the portions of the structure and the distances to the portions of the structure. The three-dimensional point cloud may include points representing geometry of the portions of the structure. The points may be associated with the acoustic responses in corresponding portions of the structure. One or more properties of the structure may be determined based on an analysis of the three-dimensional point cloud.

Flynn, Eric Brian↗
DOE OSTI2024

A GHz-frequency multistrip acoustic beam splitter for quantum applications

Here we demonstrate a microwave-frequency, two-track acoustic beam splitter, based on a multistrip coupler design matched to four unidirectional transducers, two on each of the two acoustic tracks that make up the device. We explain the device design and its experimental implementation, showing good agreement between our model and the measured device scattering spectra. The beam splitter regime, dividing an input signal at port 1 into closely equal outputs at ports 2 and 3, is reached over a 94.7 MHz bandwidth centered at 4.79 GHz, with an output power division ratio |S 21 /S 31 | 2 = 1.1 ± 0.2. The measured bandwidth of the device is limited by the bandwidth of the transducers, rather than that of the multistrip coupler.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1984

Acoustic ground impedance meter

A method and apparatus are presented for measuring the acoustic impedance of a surface in which the surface is used to enclose one end of the chamber of a Helmholz resonator. Acoustic waves are generated in the neck of the resonator by a piston driven by a variable speed motor through a cam assembly. The acoustic waves are measured in the chamber and the frequency of the generated acoustic waves is measured by an optical device. These measurements are used to compute the compliance and conductance of the chamber and surface combined. The same procedure is followed with a calibration plate having infinite acoustic impedance enclosing the chamber of the resonator to compute the compliance and conductance of the chamber alone. Then by subtracting, the compliance and conductance for the surface is obtained.

Zuckerwar, A. J.↗
NASA NTRS1988

Acoustical Convective Cooling Or Heating

Small, efficient ultrasonic device circulates fluid. Vibrating at ultrasonic frequency, piezoelectric driver sets up vortexes transfering heat to or from object in space. Used on Earth to apply localized or concentrated cooling to individual electronic components or other small parts.

Trinh, Eugene H.↗
NASA NTRS1997

Noise reducing screen devices for in-flow pressure sensors

An acoustic sensor assembly is provided for sensing acoustic signals in a moving fluid such as high speed fluid stream. The assembly includes one or more acoustic sensors and a porous, acoustically transparent screen supported between the moving fluid stream and the sensor and having a major surface disposed so as to be tangent to the moving fluid. A layer of reduced velocity fluid separating the sensor from the porous screen. This reduced velocity fluid can comprise substantially still air. A foam filler material attenuates acoustic signals arriving at the assembly from other than a predetermined range of incident angles.

Schmitz, Fredric↗
NASA NTRS1999

An Acoustic Charge Transport Imager for High Definition Television

This project, over its term, included funding to a variety of companies and organizations. In addition to Georgia Tech these included Florida Atlantic University with Dr. William E. Glenn as the P.I., Kodak with Mr. Mike Richardson as the P.I. and M.I.T./Polaroid with Dr. Richard Solomon as the P.I. The focus of the work conducted by these organizations was the development of camera hardware for High Definition Television (HDTV). The focus of the research at Georgia Tech was the development of new semiconductor technology to achieve a next generation solid state imager chip that would operate at a high frame rate (I 70 frames per second), operate at low light levels (via the use of avalanche photodiodes as the detector element) and contain 2 million pixels. The actual cost required to create this new semiconductor technology was probably at least 5 or 6 times the investment made under this program and hence we fell short of achieving this rather grand goal. We did, however, produce a number of spin-off technologies as a result of our efforts. These include, among others, improved avalanche photodiode structures, significant advancement of the state of understanding of ZnO/GaAs structures and significant contributions to the analysis of general GaAs semiconductor devices and the design of Surface Acoustic Wave resonator filters for wireless communication. More of these will be described in the report. The work conducted at the partner sites resulted in the development of 4 prototype HDTV cameras. The HDTV camera developed by Kodak uses the Kodak KAI-2091M high- definition monochrome image sensor. This progressively-scanned charge-coupled device (CCD) can operate at video frame rates and has 9 gm square pixels. The photosensitive area has a 16:9 aspect ratio and is consistent with the "Common Image Format" (CIF). It features an active image area of 1928 horizontal by 1084 vertical pixels and has a 55% fill factor. The camera is designed to operate in continuous mode with an output data rate of 5MHz, which gives a maximum frame rate of 4 frames per second. The MIT/Polaroid group developed two cameras under this program. The cameras have effectively four times the current video spatial resolution and at 60 frames per second are double the normal video frame rate.

Hunt, William D.↗
DOE OSTI2020

The Sensitivity of Chemical Kinetic Models on Flame Transfer Functions in Acoustic Fluctuation Environments with Varying Equivalence Ratios

Various factors affect the heat release response of flames – thermodynamics, hydrodynamics, acoustics, etc. The coupling of heat release rate and acoustics, in particular, is essential to the design of combustion devices so as to avoid adverse effects during their operation. Modeling flames in acoustic environments requires an accurate understanding of the fundamental physics that occurs when flames interact with a fluctuating pressure field. Over the past couple of decades, researchers have been quantifying the impact of this fluctuating pressure field on the unsteady heat release rate. The flame transfer functions computed have also been shown to depend on the level of detail in the chemical kinetic model. This paper attempts to bridge the gap between these studies to understand how sensitive the flame transfer function is to various kinetic models. The problem is studied by performing multiple one-dimensional simulations using the low-Mach solver NGA. The detailed GRI-Mech 3.0 will be used for comparison. Also, the pressure amplitude and reactant equivalence ratio are varied to understand how the environment affects this sensitivity.

Girdhar, Anant↗
DOE OSTI2023

GaAs solar cells grown on acoustically spalled GaAs substrates with 27% efficiency

Acoustic spalling presents a potentially low-cost reuse pathway for III–V epitaxial growth substrates via exfoliation of device layers with recovery and reuse of the substrate. However, surface features formed during spalling can reduce the performance of subsequently grown devices. Here, we develop an understanding of how the surface morphology of acoustically spalled substrates affects GaAs solar cell performance and develop strategies to mitigate these impacts. We demonstrate that minor planarization of the surface by wet chemical etching and/or epitaxial growth, or the redesign of the device structure to thicken critical layers, prevents performance degradation. Using these strategies, we demonstrate a 0.25 cm 2 single-junction GaAs device with 26.9% ± 0.2% photovoltaic conversion efficiency under the AM1.5G spectrum grown on an acoustically spalled substrate. These results enable the growth of high-performance III–V devices on non-traditional substrates with the potential for significantly reduced device costs.

14 SOLAR ENERGY↗
NASA NTRS1972

Development and evaluation of a device to simulate a sonic boom

A device to simulate the vibrational and acoustical properties of a sonic boom was developed and evaluated. The design employed a moving circular diaphragm which produced pressure variations by altering the volume of an air-tight enclosure that was located adjacent to an acoustical test chamber. A review of construction oriented problems, along with their solutions, is presented. The simulator is shown to produce the effects of sonic booms having pressure signatures with rise times as low as 5 milliseconds, durations as short as 80 milliseconds, and overpressures as high as 2.5 pounds per square foot. Variations in the signatures are possible by independent adjustments of the simulator. The energy spectral density is also shown to be in agreement with theory and with actual measurements for aircraft.

Rash, L. C.↗
NASA NTRS1999

An Experiment Investigation of Fully-Modulated, Turbulent Diffusion Flames in Reduced Gravity

Pulsed combustion appears to have the potential to provide for rapid fuel/air mixing, compact and economical combustors, and reduced exhaust emissions. The ultimate objective of this program is to increase the fundamental understanding of the fuel/air mixing and combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. In this research the fuel jet is fully-modulated (i.e., completely shut off between pulses) by an externally controlled valve system. This can give rise to drastic modification of the combustion and flow characteristics of flames, leading to enhanced fuel/air mixing mechanisms not operative for the case of acoustically excited or partially-modulated jets. In addition, the fully-modulated injection approach avoids the strong acoustic forcing present in pulsed combustion devices, significantly simplifying the mixing and combustion processes. Relatively little is known of the behavior of turbulent flames in reduced-gravity conditions, even in the absence of pulsing. The goal of this Flight-Definition experiment (PUFF, for PUlsed-Fully Flames) is to establish the behavior of fully-modulated, turbulent diffusion flames under microgravity conditions. Fundamental issues to be addressed in this experiment include the mechanisms responsible for the flame length decrease for fully-modulated, turbulent diffusion flames compared with steady flames, the impact of buoyancy on the mixing and combustion characteristics of these flames, and the characteristics of turbulent flame puffs under fully momentum-dominated conditions.

Hermanson, J. C.↗
NASA NTRS2008

Solid Micro Horn Array (SMIHA) for Acoustic Matching

Transduction of electrical signals to mechanical signals and vice-versa in piezoelectric materials is controlled by the material coupling coefficient. In general in a loss-less material the ratio of energy conversion per cycle is proportional to the square of the coupling coefficient. In practical transduction however the impedance mismatch between the piezoelectric material and the electrical drive circuitry or the mechanical structure can have a significant impact on the power transfer. This paper looks at novel methods of matching the acoustic impedance of structures to the piezoelectric material in an effort to increase power transmission and efficiency. In typical methods the density and acoustic velocity of the matching layer is adjusted to give good matching between the transducer and the load. The approach discussed in this paper utilizes solid micro horn arrays in the matching layer which channel the stress and increase the strain in the layer. This approach is found to have potential applications in energy harvesting, medical ultrasound and in liquid and gas coupled transducers.

power transmission↗
DOE OSTI2020

Identifications and classifications of human locomotion using Rayleigh-enhanced distributed fiber acoustic sensors with deep neural networks

Abstract This paper reports on the use of machine learning to delineate data harnessed by fiber-optic distributed acoustic sensors (DAS) using fiber with enhanced Rayleigh backscattering to recognize vibration events induced by human locomotion. The DAS used in this work is based on homodyne phase-sensitive optical time-domain reflectometry (φ-OTDR). The signal-to-noise ratio (SNR) of the DAS was enhanced using femtosecond laser-induced artificial Rayleigh scattering centers in single-mode fiber cores. Both supervised and unsupervised machine-learning algorithms were explored to identify people and specific events that produce acoustic signals. Using convolutional deep neural networks, the supervised machine learning scheme achieved over 76.25% accuracy in recognizing human identities. Conversely, the unsupervised machine learning scheme achieved over 77.65% accuracy in recognizing events and human identities through acoustic signals. Through integrated efforts on both sensor device innovation and machine learning data analytics, this paper shows that the DAS technique can be an effective security technology to detect and to identify highly similar acoustic events with high spatial resolution and high accuracies.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Hybrid semiconductor-piezoacoustic radiofrequency device

An amplifying radiofrequency device includes a piezoelectric film and a semiconductor amplifier layer. The piezoelectric film is conformed as an acoustic waveguide. The piezoelectric film has a principal acoustic propagation direction parallel to the principal conduction direction of the amplifier layer. Interdigitated transducers are positioned on the piezoelectric film to respectively launch an acoustic wave in response to an input RF signal, and transduce the acoustic wave back to an output RF signal. There is a distance of less than the acoustic wavelength between the semiconductor amplifier layer and the piezoelectric film. The piezoelectric film has a thickness of less than the acoustic wavelength. According to a method for making such a device, a stack of III-V layers is epitaxially grown on a III-V substrate, wherein the stack comprises a first etch stop layer, a second etch stop layer, an amplifier layer, and a contact layer. The stack is bonded to a lithium niobate film. The III-V substrate is removed by etching down to the first etch stop layer. Deposition windows are opened by etching from the first etch stop layer down to the contact layer. Metal contact electrodes are deposited in the deposition windows.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ultrafast low-temperature metal–insulator interface phonon dynamics and heat transport in a Pt/Gd 3 Fe 5 O 12 heterostructure

Interfacial thermal and acoustic phenomena have an important role in quantum science and technology, including in spintronic and spincaloritronic materials and devices. Simultaneous measurements of the low-temperature thermal and acoustic properties of a metal/insulator heterostructure reveal distinct dynamics in the characteristic phonon frequency ranges of acoustic and thermal transport. The measurements probed a heterostructure consisting of a thin film of Pt on the ferrimagnetic insulator gadolinium iron garnet (Gd 3 Fe 5 O 12 , GdIG) grown epitaxially on a gadolinium gallium garnet substrate. Ultrafast structural dynamics within the Pt layer were tracked using time-resolved ultrafast x-ray diffraction and analyzed to probe interfacial acoustic and thermal properties. The rapid heating of the Pt layer by a 400 nm wavelength femtosecond-duration optical pulse produced transient structural changes that provided the stimulus for these measurements. Rapid heating produced a broadband acoustic pulse that was partially reflected by the Pt/GdIG interface. Temporal frequencies up to 740 GHz, corresponding to angular frequencies of several THz, were detected in a wavelet analysis of the acoustic oscillations of the strain in the Pt layer. The structural results were analyzed to determine (i) the acoustic damping coefficient and phonon mean free path in Pt at frequencies of hundreds of GHz and (ii) the Grüneisen anharmonicity parameter. The thermal conductance of the Pt/GdIG interface was tracked using the slower, tens-of-picosecond-scale, dynamics of the initial cooling of the heated Pt layer. Analysis using a model based on the Boltzmann transport equation shows that the phonon transmission is lower at the phonon frequencies relevant to thermal transport than for subterahertz regime acoustics.

Acoustic phenomena↗
NASA NTRS2004

Modeling Nonlinear Acoustic Standing Waves in Resonators: Theory and Experiments

The overall goal of the cooperative research with NASA Glenn is to fundamentally understand, computationally model, and experimentally validate non-linear acoustic waves in enclosures with the ultimate goal of developing a non-contact acoustic seal. The longer term goal is to transition the Glenn acoustic seal innovation to a prototype sealing device. Lucas and coworkers are credited with pioneering work in Resonant Macrosonic Synthesis (RMS). Several Patents and publications have successfully illustrated the concept of Resonant Macrosonic Synthesis. To utilize this concept in practical application one needs to have an understanding of the details of the phenomenon and a predictive tool that can examine the waveforms produced within resonators of complex shapes. With appropriately shaped resonators one can produce un-shocked waveforms of high amplitude that would result in very high pressures in certain regions. Our goal is to control the waveforms and exploit the high pressures to produce an acoustic seal. Note that shock formation critically limits peak-to-peak pressure amplitudes and also causes excessive energy dissipation. Proper shaping of the resonator is thus critical to the use of this innovation.

Raman, Ganesh↗