SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Report discusses research directed toward automated diagnosis of faults in complicated electromechanical and hydraulic systems aiming 70-m and 34-m antennas of Deep Space Network communication system.
For optimum performance, a ground antenna system must maximize the ratio of received signal to the receiving system noise power, defined as the ratio of antenna gain to system-noise temperature (G/T). The total system noise temperature is the linear combination of the receiver noise temperature (including the feed system losses) and the antenna noise contribution. Hence, for very low noise cryogenic receiver systems, antenna noise-temperature properties are very significant contributors to G/T.It is well known that, for dual reflector systems designed for maximum gain, the gain performance of the antenna system is the same for both Cassegrain and Gregorian configurations. For a12-meter antenna designed to be part of the large array based Deep Space Network, a Cassegrain configuration designed for maximum G/T at X-band was 0.7 dB higher than the equivalent Gregorian configuration. This study demonstrates that, for maximum GIT, the dual shaped Cassegrain design is always better than the Gregorian.
The Space Telescope (ST), carrying five astronomy instruments, is a long-life spacecraft designed to achieve and maintain ultrafine stabilization jitter performance. The rms jitter specification for pointing performance is 7 marcsec (1sigma) during periods of scientific observation. Spacecraft attitude control is achieved by onboard computer processing of attitude and rate sensor data to generate reaction-wheel torque commands. The ST Antenna Pointing System is used to position a high-gain antenna for relaying science and engineering data from the spacecraft to the ground station.
This paper presents a progress summary of NASA's efforts in developing 20 and 30 GHz GaAs MMIC devices and an advanced satellite communications antenna system using these devices. In the interest of preserving resources such as frequency spectrum and orbital space the antenna system is being developed with multiple fixed spot beams and multiple scanning spot beams. NASA set high goals for the MMIC development to pushc GaAs technology. These goals and the main features of the MMIC devices are discussed. Some packaging and characterization considerations are also discussed. The 20 GHz transmit antenna and 30 GHz receive antenna are being developed separately. The approach selected is to perform contractual configuration studies, purchase a 20-GHz experimental antenna system (EAS) and perform in-house evaluation. The features and key specifications of the EAS are discussed. Additional supporting technologies such as effects of coupling on modest sized arrays, MMIC matching techniques, in-house analytical capability, wideband and dual frequency microstrip patch array development, and MMIC packaging techniques are described. Some plans for future are also discussed.
This paper presents a progress summary of NASA's efforts in developing 20 and 30 GHz GaAs MMIC devices and an advanced satellite communications antenna system using these devices. In the interest of preserving resources such as frequency spectrum and orbital space the antenna system is being developed with multiple fixed spot beams and multiple scanning spot beams. NASA set high goals for the MMIC development to push GaAs technology. These goals and the main features of the MMIC devices are discussed. Some packaging and characterization considerations are also discussed. The 20 GHz transmit antenna and 30 GHz receive antenna are being developed separately. The approach selected is to perform contractual configuration studies, purchase a 20-GHz experimental antenna system (EAS) and perform in-house evaluation. The features and key specifications of the EAS are discussed. Additional supporting technologies such as effects of coupling on modest sized arrays, MMIC matching techniques, in-house analytical capability, wideband and dual frequency microstrip patch array development, and MMIC packaging techniques are described. Some plans for future work are also discussed.
A simplified controller system for a seven element phase array antenna is described, and information necessary for operation of the system is given.
The paper discusses various aspects of the system design for a satellite in a highly elliptical inclined orbit, and presents a number of antenna design options for the proposed Archimedes mission. A satellite constellation was studied for the provision of multi media communication services in the L and S Band for northern latitudes. The inclined elliptical orbit would allow coverage of Europe, America, and East Asia. Using Canada and North America as the baseline coverage area, this paper addresses system considerations such as the satellite configuration and pointing, beam configuration, and requirements for antennas. A trade-off is performed among several antenna candidates including a direct radiating array, a focal-fed reflector, and a single reflector imaging system. Antenna geometry, performance, and beam forming methods are described. The impact of the designs on the antenna deployment is discussed.
Antenna simulator provides for evaluation checkout of corporate feeds, monopulse sum-and-difference networks, etc., in a shielded environment prior to system checkout on an antenna pattern range. This technique is useful wherever simulation of monopulse antenna element characteristics is desired for checkout of ancillary equipment in a controlled environment.
The Project Echo communications experiment employed large, steerable,transmitting and receiving antennas at the ground terminals. It was necessary that these highly directional antennas be continuously and accurately pointed at the passing satellite. This paper describes a new type of special purpose data converter for directing narrow-beam communication antennas on the basis of predicted information. The system is capable of converting digital input data into real-time analog voltage commands with a dynamic accuracy of +/- 0.05 degree, which meets the requirements of the present antennas.
This paper describes a two-axis drive system for pointing a high-gain antenna. Motion about each axis is provided by identical drive mechanisms. The drive is unique in that only three gear passes are required to obtain the necessary 900:1 gear reduction. The drive system is a primary element of an experiment that will provide a real-time data link between Nimbus and certain ground stations. In this experiment data are transmitted from Nimbus to the applications technology satellite, which relays the data to ground stations.
Creation of an antenna system that could autonomously adapt contours of reflecting surfaces to compensate for structural loads induced by a variable environment would maximize performance of space-based communication systems. Design of such a system requires the comprehensive development and integration of advanced actuator, sensor, and control technologies. As an initial step in this process, a test has been performed to assess the use of a shape memory alloy as a potential actuation technique. For this test, an existing, offset, cassegrain antenna system was retrofit with a subreflector equipped with shape memory alloy actuators for surface contour control. The impacts that the actuators had on both the subreflector contour and the antenna system patterns were measured. The results of this study indicate the potential for using shape memory alloy actuation techniques to adaptively control antenna performance; both variations in gain and beam steering capabilities were demonstrated. Future development effort is required to evolve this potential into a useful technology for satellite applications.
The optimun design parameters for a swept frequency wide-band radiometric antenna system for spacecraft applications are studied. Wide band antenna systems are needed to observe layered surfaces which are frequency sensitive and require multiple measurements for interpretation. The lowest frequency band of interest is between 1.4 to 2.8 Ghz. Starting with a given size reflector fed in the offset mode by a corrugated horn located at the focus of the parabola, the primary performance indexes; e.g., half power beamwidth, cross polarization level, and overall beam efficiency were calculated over a wide frequency range (two to one) for different physical horn dimensions and for different values of f/D ratio. These data are used to find the best design under given restriction of reflector size and blockage.
Applications that require data transmission at high temperatures are becoming more common due to growing commercial and military needs. Antennas are an indispensable part of these systems and the ability to characterize them at elevated temperatures is quite complicated with little or no information being reported on the subject [1]. This paper describes a measurement system that can characterize planar antennas up 600 C with ground-signal-ground (GSG) or ground-signal (GS) probe contacts. The return loss and radiation patterns of a folded slot antenna (FSA), designed to operate at 5 GHz (no ground plane on back side) and fabricated on an alumina substrate, are presented at room temperature (RT) and 250 C [2]. All measurements were made with Agilent's Precision Network Analyzer (PNA) E8361. The return loss and radiation patterns were also measured on a Styrofoam chuck to illustrate the effect the high temperature measurement system has on the patterns.
Four major areas of interest are covered: technology pertinent to large antenna systems; technology related to the control of large space systems; basic technology concerning structures, materials, and analyses; and flight technology experiments. Large antenna systems and flight technology experiments are described. Design studies, structural testing results, and theoretical applications are presented with accompanying validation data. These research studies represent state-of-the art technology that is necessary for the development of large space systems. A total systems approach including structures, analyses, controls, and antennas is presented as a cohesive, programmatic plan for large space systems.
The isolation between the upper S-band quad antenna and the S-band payload antenna on the shuttle orbiter is calculated using a combination of plane surface and curved surface theories along with worst case values. A minimum value of 60 db isolation is predicted based on recent antenna pattern data, antenna locations on the orbiter, curvature effects, dielectric covering effects and edge effects of the payload bay. The calculated value of 60 db is significantly greater than the baseline value of 40 db. Use of the new value will result in the design of smaller, lighter weight and less expensive filters for S-band transponder and the S-band payload interrogator.
A parameter and state estimation technique for distributed models is demonstrated through the solution of a problem generic to large space antenna system identification. Assuming the position of the reflective surface of the maypole (hoop/column) antenna to be approximated by the static two-dimensional, stretched-membrane partial differential equation with variable-stiffness coefficient functions, a spline-based approximation procedure is described that estimates the shape and stiffness functions from data set observations. For given stiffness functions, the Galerkin projection with linear spline-based functions is applied to project the distributed problem onto a finite-dimensional subspace wherein algebraic equations exist for determining a static shape (state) prediction. The stiffness functions are then parameterized by cubic splines and the parameters estimated by an output error technique. Numerical results are presented for data descriptive of a 100-m-diameter maypole antenna.
A set of basic terminology related to deep space ranging measurements is proposed. Calibration equations are derived for the dish-mounted zero delay device method for 26-m antenna systems and the translator method for 64-m antenna systems.
Mathematical modeling and design analysis is carried out for large flexible spacecraft and antenna systems. Modeling topics include inertially fixed attitude stabilization, solar radiation pressure effects, control systems for space mast structures, and optimal control of a hoop/column space antenna system. Each subject includes a brief overview of the pertinent literature and details of the proposed solutions for the specific modeling tasks.