Search NASA⌕ Search

SEARCH · Search NASA

Results for “bleed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Dual throat thruster test results

Test results are presented for a dual throat thruster burning gaseous oxygen and hydrogen at primary (inner) chamber pressures from 380 to 680 psia. Heat flux profiles were obtained from calorimetric cooling channels in the inner nozzle, outer or secondary chamber and the tip of the inner nozzle. Data were obtained for two nozzle spacings over a chamber pressure ratio (secondary/primary) range of 0.45 to 0.83 with both chambers firing (Mode I). Fluxes near the end of the inner nozzle were significantly higher than in Mode II when only the inner chamber was fired, due to flow separation and recirculation caused by the back pressure imposed by the secondary chamber. As the pressure ratio increased, these heat fluxes increased and the region of high heat flux relative to Mode II extended farther upstream. The use of a gaseous hydrogen bleed flow in the secondary chamber to control heat fluxes in the primary plume attachment region was investigated in Mode II testing. A bleed flow of less than two percent of the primary chamber flow was required.

Ewen, R. L.↗
NASA NTRS1987

A potential flight evaluation of an upper-surface-blowing/circulation-control-wing concept

The technology data base for powered lift aircraft design has advanced over the last 15 years. NASA's Quiet Short Haul Research Aircraft (QSRA) has provided a flight verification of upper surface blowing (USB) technology. The A-6 Circulation Control Wing flight demonstration aricraft has provide data for circulation control wing (CCW) technology. Recent small scale wind tunnel model tests and full scale static flow turning test have shown the potential of combining USB with CCW technology. A flight research program is deemed necessary to fully explore the performance and control aspects of CCW jet substitution for the mechanical USB Coanda flap. The required hardware design would also address questions about the development of flight weight ducts and CCW jets and the engine bleed-air capabilities vs requirements. NASA's QSRA would be an optimum flight research vehicle for modification to the USB/CCW configuration. The existing QSRA data base, the design simplicity of the QSRA wing trailing edge controls, availability of engine bleed-air, and the low risk, low cost potential of the suggested program is discussed.

Riddle, Dennis W.↗
NASA NTRS1990

Improved Insert For Variable Mach Number

Nozzle insert lowers wind-tunnel mach number while maintaining excellent flow quality. Essential components of improved design include sonic first throat, expansion surface, variable boundary-layer bleed, insert itself, and existing, unchanged, contour of nozzle. Modification involves creation of secondary throat and critical addition of boundary-layer bleed path between insert and original tunnel wall. Enables quick change of mach number in existing facility at relatively low cost and requires no special contouring of existing nozzle. Represents simple and cost-effective method of altering mach number in any supersonic wind tunnel.

Puster, Richard L.↗
NASA NTRS1990

Comparison of 3-D viscous flow computations of Mach 5 inlet with experimental data

The accuracy of the time-marching three-dimensional Navier-Stokes code PARC3D (Cooper et al., 1987) is evaluated using experimental data on a Mach 5 mixed-compression inlet configuration, obtained in the 10 x 10-ft working section of the supersonic wind tunnel at NASA Lewis. The basic principles of the PARC3D computations (in which the inlet and tunnel geometry and the bleed conditions are fully modeled) and the experimental setup are described, and the results are presented in extensive graphs and characterized in detail. PARC3D is shown to give reasonably accurate predictions of the bleed-zone elimination of low-energy vortical flow due to shock/boundary-layer interaction; various possible improvements are briefly considered.

Reddy, D. R.↗
NASA NTRS1989

Flight/propulsion control integration for V/STOL fighter/attack aircraft

A NASA-defined technology program investigating integrated flight/propulsion control system design for vertical and short takeoff and landing (V/STOL) aircraft is outlined, and initial fixed-base simulation experiments for two V/STOL aircraft are covered. It is shown that transition performance can be characterized by the minimum climb or level-flight acceleration that can be achieved. Level-1 flying qualities can be achieved for deceleration to hover in instrument conditions, and for shore-based and shipboard landing when attitude and velocity stabilization and command augmentation modes are provided. Level-1 and Level-2 flying qualities can be expected when only attitude command is provided. During vertical landing aboard a destroyer in heavy seas, substantial bleed flow rates are reported for a control arrangement employing reaction control for the pitch, roll, and yaw axes. Peak bleed flows can be reduced for a control arrangement using lateral-thrust transfer for roll control.

Franklin, James A.↗
NASA NTRS1991

Results from computational analysis of a mixed compression supersonic inlet

A numerical study was performed to simulate the critical flow through a supersonic inlet. This flowfield has many phenomena such as shock waves, strong viscous effects, turbulent boundary layer development, boundary layer separations and mass flow suction through the walls (bleed). The computational tools used in this study were two full Navier-Stokes (FNS) codes. The supersonic inlet that was analyzed in this study is the Variable Diameter Centerbody (VDC), inlet. This inlet is a candidate concept for the next generation supersonic transport. Application of the code to the inlet geometry involved effort in generating an efficient grid geometry and specifying boundary conditions, particularly in the bleed region and at the outflow boundary. Results for a critical inlet operation compare favorably to Method of Characteristics predictions and experimental data.

Saunders, J. D.↗
NASA NTRS1991

Results from computational analysis of a mixed compression supersonic inlet

A numerical study was performed to simulate the critical flow through a supersonic inlet. This flow field has many phenomena such as shock waves, strong viscous effects, turbulent boundary layer development, boundary layer separations, and mass flow suction through the walls, (bleed). The computational tools used were two full Navier-Stokes (FNS) codes. The supersonic inlet that was analyzed is the Variable Diameter Centerbody, (VDC), inlet. This inlet is a candidate concept for the next generation supersonic involved effort in generating an efficient grid geometry and specifying boundary conditions, particularly in the bleed region and at the outflow boundary. Results for a critical inlet operation compare favorably to Method of Characteristics predictions and experimental data.

Saunders, J. D.↗
NASA NTRS1992

Cycle O(CY1991) NLS trade studies and analyses report. Book 2, part 2: Propulsion

This report documents the propulsion system tasks performed in support of the National Launch System (NLS) Cycle O preliminary design activities. The report includes trades and analyses covering the following subjects: (1) Maximum Tank Stretch Study; (2) No LOX Bleed Performance Analysis; (3) LOX Bleed Trade Study; (4) LO2 Tank Pressure Limits; (5) LOX Tank Pressurization System Using Helium; (6) Space Transportation Main Engine (STME) Heat Exchanger Performance; (7) LH2 Passive Recirculation Performance Analysis; (8) LH2 Bleed/Recirculation Study; (9) LH2 Tank Pressure Limits; and (10) LH2 Pressurization System. For each trade study an executive summary and a detailed trade study are provided. For the convenience of the reader, a separate section containing a compilation of only the executive summaries is also provided.

Cronin, R.↗
NASA NTRS1993

SNTP propellant management system

Viewgraphs on the following are presented: (1) space nuclear thermal propulsion (SNTP) propellant management system; (2) SNTP cycle selection; (3) NTP system components unique design constraints; (4) bleed cycle unique design requirement for turbopump; (5) bleed cycle turbopump; (6) SNTP carbon-carbon turbine wheel; and (7) turbine development program.

Tippetts, Tom↗
NASA NTRS1993

Liquid oxygen (LO2) propellant conditioning concept testing

Testing of a simplified LO2 propellant conditioning concept for future expendable launch vehicles is discussed. Four different concepts are being investigated: no-bleed, low-bleed, use of a recirculation line, and He bubbling. A full-scale test article, which is a facsimile of a propellant feed duct with an attached section to simulate heat input from an LO2 turbopump, is to be tested at the Cold Flow Facility of the Marshall Space Flight Center West Test Area. Work to date includes: design and fabrication of the test article, design of the test facility and initial fabrication, development of a test matrix and test procedures, initial predictions of test output, and heat leak calibration and heat exchanger tests on the test articles.

Perry, Gretchen L. E.↗
NASA NTRS1953

Analysis of several methods of pumping cooling air for turbojet engine afterburners

Several methods of pumping air to an annular cooling passage surrounding a typical axial-flow turbojet-engine afterburner were evaluated and compared on the basis of thrust and specific fuel consumption of the systems. Each system was analyzed over a range of afterburner-wall temperatures, flight Mach numbers, and exhaust-gas temperatures at sea level and 35,000 feet. Ram pressure recovery, boundary-layer pressure recovery, and the engine-jet actuated ejector appear to be satisfactory systems at high Mach numbers. Cooling with compressor-exit air bleed was found to be unsatisfactory,but the use of compressor-exit bleed air as the primary fluid in a high-performance ejector was satisfactory. The use of an auxiliary compressor driven from the engine shaft increased the thrust and decreased the specific fuel consumption of the engine for many of the conditions investigated.

PUMPS, JET AND THRUST AUGMENTORS↗
NASA NTRS1956

Jet Effects on Base and Afterbody Pressures of a Cylindrical Afterbody at Transonic Speeds

An investigation of the effects of jet nozzle geometry, size of base annulus, and base bleed upon the base and afterbody pressures of a cylindrical afterbody at transonic speeds has been conducted. Sonic and supersonic conical nozzles with jet-to-base diameter ratios from 0.25 to 0.85 were investigated with a cold jet at jet total-pressure ratios up to approximately 8.0 through a Mach number range from 0.6 to 1.25. Base pressure coefficients of about -0.55 were measured for the sonic nozzles at a Mach number of 1 or greater. The jet-to-base diameter ratio had a substantial effect on the base pressure obtained on the cylindrical afterbody of this investigation. Base bleed was beneficial in increasing the base pressure under certain conditions but had little or no effect at certain other conditions.

Cubbage, James M , Jr↗
NASA NTRS1993

Liquid Oxygen (LO2) propellant conditioning concept testing

Marshall Space Flight Center (MSFC) and industry contractors have undertaken activities to develop a simplified liquid oxygen (LO2) propellant conditioning concept for future expendable launch vehicles. The objective of these activities is to reduce operations costs and timelines and to improve safety of these vehicles. The approach followed has been to identify novel concepts through system level studies and demonstrate the feasibility of these concepts through small-scale and full-scale testing. Testing will also provide data for design guidelines and validation of analytical models. Four different concepts are being investigated: no-bleed, low-bleed, use of a recirculation line, and helium (He) bubbling. This investigation is being done under a Joint Institutional Research and Development (JIRAD) program currently in effect between MSFC and General Dynamics Space Systems (GDSS). A full-scale test article, which is a facsimile of a propellant feed duct with an attached section to simulate heat input from a LO2 turbopump, will be tested at the Cold Flow Facility at MSFC's West Test Area. Liquid nitrogen (LN2), which has similar properties to LO2, will be used in place of LO2 for safety and budget reasons. Work to date includes design and fabrication of the test article, design of the test facility and initial fabrication, development of a test matrix and test procedures, initial predictions of test output, and heat leak calibration and heat exchanger tests on the test article. The tests for all propellant conditioning concepts will be conducted in the summer of 1993, with the final report completed by October, 1993.

Perry, Gretchen L. E.↗
NASA NTRS1994

Combat Agility Management System (CAMS)

The proper management of energy becomes a complex task in fighter aircraft which have high angle of attack (AOA) capability. Maneuvers at high AOA are accompanied by high bleed rates (velocity decrease), a characteristic that is usually undesirable in a typical combat arena. Eidetics has developed under NASA SBIR Phase 1 and NAVAIR SBIR Phase 2 contracts a system which allows a pilot to more easily and effectively manage the trade-off of energy (airspeed or altitude) for turn rate while not imposing hard limits on the high AOA nose pointing capability that can be so important in certain air combat maneuver situations. This has been accomplished by incorporating a two-stage angle of attack limiter into the flight control laws. The first stage sets a limit on AOA to achieve a limit on the maximum bleed rate (selectable) by limiting AOA to values which are dependent on the aircraft attitude and dynamic pressure (or flight path, velocity, and altitude). The second stage sets an AOA limit near the AOA for C(sub l max). One of the principal benefits of such a system is that it enables a low-experience pilot to become much more proficient at managing his energy. The Phase 2 simulation work is complete, and an exploratory flight test on the F-18 HARV is planned for the Fall of 1994 to demonstrate/validate the concept.

Skow, Andrew↗
NASA NTRS1992

A surgical support system for Space Station Freedom

Surgical techniques in microgravity are being developed for the Health Maintenance Facility (HMF) on Space Station Freedom (SSF). This will be a presentation of the proposed surgical capabilities and ongoing hardware and procedural investigations. Methods: Procedures and prototype hardware, which include a medical restraint system, a surgical overhead isolation canopy, a suction device, and a regional laminar flow device were evaluated. This was accomplished by realistic sterile surgical simulations involving both mannequins and animals during KC-135 parabolic flight and in a high fidelity ground based HMF mockup. Results: Animal surgery in the environment of microgravity allowed the observation of unique arterial and venous bleeding characteristics for the first time. The ability to control bleeding and to prevent cabin atmosphere contamination was also demonstrated. Conclusions: The procedures and prototype hardware tested provided valuable information and should be investigated and developed further. The use of standard surgical techniques are possible in microgravity if the principles of personnel and supply restraint and operative field containment are adhered to.

Campbell, M. R.↗
NASA NTRS1996

Dynamic Modeling of Starting Aerodynamics and Stage Matching in an Axi-Centrifugal Compressor

A DYNamic Turbine Engine Compressor Code (DYNTECC) has been modified to model speed transients from 0-100% of compressor design speed. The impetus for this enhancement was to investigate stage matching and stalling behavior during a start sequence as compared to rotating stall events above ground idle. The model can simulate speed and throttle excursions simultaneously as well as time varying bleed flow schedules. Results of a start simulation are presented and compared to experimental data obtained from an axi-centrifugal turboshaft engine and companion compressor rig. Stage by stage comparisons reveal the front stages to be operating in or near rotating stall through most of the start sequence. The model matches the starting operating line quite well in the forward stages with deviations appearing in the rearward stages near the start bleed. Overall, the performance of the model is very promising and adds significantly to the dynamic simulation capabilities of DYNTECC.

Wilkes, Kevin↗
NASA NTRS1998

Flowfield Measurements in a Slot-Bled Oblique Shock Wave and Turbulent Boundary-Layer Interaction

An experimental investigation was conducted to determine the flowfield inside a bleed slot used to control an oblique shock-wave and turbulent boundary-layer interaction. The slot was oriented normal to the primary flow direction and had a width of 1.0 cm (primary flow direction), a length of 2.54 cm, and spanned 16.5 cm. The approach boundary layer upstream of the interaction was nominally 3.0 cm thick. Two operating conditions were studied: M = 1.98 with a shock generator deflection angle of 6 deg and M= 2.46 with a shock generator deflection angle of 8 deg. Measurements include surface and flowfield static pressure, Pitot pressure, and total mass-flow through the slot. The results show that despite an initially two-dimensional interaction for the zero bleed-flow case, the slot does not remove mass uniformly in the spanwise direction. Inside the slot, the flow is characterized by two separation regions which significantly reduce the effective flow area. The upper separation region acts as an aerodynamic throat resulting in supersonic flow through much of the slot.

Davis, D. O.↗