Results for “boundary layer height” — Page 13

NASA NTRSDate not supplied

PBL Thermodynamic Characterization and Its Variability From NAST-I During the Wh2yMSIE Field Campaign

The National Airborne Sounder Testbed-Interferometer (NAST‑I) suborbital system (<2.6 km IFOV; 0.25 cm-1 within 645–2700 cm‑1) serves as a spaceborne instrument simulator and pathfinder for future satellite capabilities and airborne science experiments. The NAST‑I measurements are made to advance understanding of science critical for weather, climate, chemistry, and radiation applications. Here we present some groundbreaking capabilities of NAST-I measurements and corresponding geophysical retrievals and their potential benefits toward improved atmospheric state and composition characterizations needed for science applications of particular importance toward enhancing characterization and understanding of the Planetary Boundary Layer (PBL). Initial results of PBL height estimation and thermodynamic characterization and their time evolution from NAST-I measurements during the WH2yMSIE field campaign are presented.

Daniel K Zhou↗

NASA NTRS2023

Irrigated Agriculture Significantly Modifies Seasonal Boundary Layer Atmosphere and Lower Tropospheric Convective Environment

Modification of grasslands into irrigated and nonirrigated agriculture in the Great Plains resulted in significant impacts on weather and climate. However, there has been lack of observational data–based studies solely focused on impacts of irrigation on the PBL and convective conditions. The Great Plains Irrigation Experiment (GRAINEX), conducted during the 2018 growing season, collected data over irrigated and nonirrigated land uses over Nebraska to understand these impacts. Specifically, the objective was to determine whether the impacts of irrigation are sustained throughout the growing season. The data analyzed include latent and sensible heat flux, air temperature, dewpoint temperature, equivalent temperature (moist enthalpy), PBL height, lifting condensation level (LCL), level of free convection (LFC), and PBL mixing ratio. Results show increased partitioning of energy into latent heat relative to sensible heat over irrigated areas while average maximum air temperature was decreased and dewpoint temperature was increased from the early to peak growing season. Radiosonde data suggest reduced planetary boundary layer (PBL) heights at all launch sites from the early to peak growing season. However, reduction of PBL height was much greater over irrigated areas than over nonirrigated croplands. Relative to the early growing period, LCL and LFC heights were also lower during the peak growing period over irrigated areas. Results note, for the first time, that the impacts of irrigation on PBL evolution and convective environment can be sustained throughout the growing season and regardless of background atmospheric conditions. These are important findings and applicable to other irrigated areas in the world.

Emilee Lachenmeier↗

NASA NTRS1985

An experimental investigation of a swirling, axisymmetric, turbulent boundary layer with pressure gradient

The results of an experimental investigation designed to document data on both mean and turbulence quantities in the axisymmetric, swirling boundary layer (with and without a pressure gradient) flowing over a stationary cylinder downstream of a spinning cylindrical section are discussed. The pressure gradient was introduced into the flow field by a 25.4-mm-high, forward-facing circular step mounted on the stationary cylinder, the step height being nearly equal to the approaching boundary-layer thickness. All the measurements were made at upstream reference velocity of 36-37 m/sec, with the rotation of the spinner set to make its peripheral speed equal to the reference velocity. The data reported include measurements of surface pressure and the mean surface-shear-stress vector (using a miniature directional surface-fence gage) and oil-flow visualization studies of the stationary cylinder. The data indicate that the streamwise pressure gradient controls the development of the streamwise component of wall shear but leaves the peripheral component of wall shear practically unaffected.

Hebbar, S. K.↗

NASA NTRSDate not supplied

Progress on the Development of a Step Height Sensor for the BOLT Flight Vehicle

Explore the source record for details and available documents.

Boundary Layer↗

NASA NTRS2009

Boundary Layer Transition Protuberance Tests at NASA JSC Arc-Jet Facility

A series of arc-jet tests in support of the Shuttle Orbiter Boundary Layer Transition flight experiment was conducted in the Channel Nozzle of the NASA Johnson Space Center Atmospheric Reentry Materials and Structures Facility. The boundary layer trip was a protrusion of a certain height and geometry fabricated as part of a 6"x6" tile insert, a special test article made of the Boeing Rigid Insulation tile material and coated with the Reaction Cured Glass used for the bottom fuselage tiles of the Space Shuttle Orbiter. A total of five such tile inserts were manufactured: four with the 0.25-in. trip height, and one with the 0.35-in. trip height. The tile inserts were interchangeably installed in the center of the 24"x24" variable configuration tile array mounted in the 24"x24" test section of the channel nozzle. The objectives of the test series were to demonstrate that the boundary layer trip can safely withstand the Space Shuttle Orbiter flight-like re-entry environments and provide temperature data on the protrusion surface, surfaces of the nearby tiles upstream and downstream of the trip, as well as the bond line between the tiles and the structure. The targeted test environments were defined for the tip of the protrusion, away from the nominal surface of the tile array. The arc jet test conditions were approximated in order to produce the levels of the free stream total enthalpy at the protrusion height similar to those expected in flight. The test articles were instrumented with surface, sidewall and bond line thermocouples. Additionally, Tempilaq temperature-indicating paint was applied to the nominal tiles of the tile array in locations not interfering with the protrusion trip. Five different grades of paint were used that disintegrate at different temperatures between 1500 and 2000 deg F. The intent of using the paint was to gauge the RCG-coated tile surface temperature, as well as determine its usefulness for a flight experiment. This paper provides an overview of the channel nozzle arc jet, test articles and test conditions, as well as the results of the arc-jet tests including the measured temperature response of the test articles, their pre- and post-test surface scans, condition of the thermal paint, and continents on the protrusion tip heating achieved in tests compared to the computational fluid dynamics predictions.

Larin, M. E.↗

NASA NTRS2006

Shuttle Return To Flight Experimental Results: Protuberance Effects on Boundary Layer Transition

The effect of isolated roughness elements on the windward boundary layer of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamic Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental effort was initiated to provide a roughness effects database for developing transition criteria to support on-orbit decisions to repair damage to the thermal protection system. Boundary layer transition results were obtained using trips of varying heights and locations along the centerline and attachment lines of 0.0075-scale models. Global heat transfer images using phosphor thermography of the Orbiter windward surface and the corresponding heating distributions were used to infer the state of the boundary layer (laminar, transitional, or turbulent). The database contained within this report will be used to formulate protuberance-induced transition correlations using predicted boundary layer edge parameters.

Liechty, Derek S.↗

NASA NTRS2021

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS1992

Integration of satellite and surface data using a radiative-convective oceanic boundary-layer model

A mixing-line boundary-layer model is used to retrieve cloud-top height from satellite-derived cloud-top temperatures, using 700-hPa National Meteorological Center (NMC) analyses and the Comprehensive Ocean and Atmosphere Data Set (COADS) surface data as supporting datasets. Results are compared with the fixed-lapse-rate method of retrieving boundary-layer depth from sea surface temperatures (SST) and cloud-top temperatures. A radiative-convective equilibrium boundary-layer model is used to retrieve boundary-layer structure given SST and surface wind, satellite cloud-top temperatures and cloud fraction, and the 700-hPa NMC thermodynamic analyses. Good agreement is found between the COADS data and the model solutions for low-level temperature and moisture. This suggests that equilibrium boundary-layer models may be of use over remote oceans in the retrieval of boundary-layer structure.

Betts, Alan K.↗

NASA NTRS2008

Aerothermodynamic Testing and Boundary Layer Trip Sizing of the HIFiRE Flight 1 Vehicle

An experimental wind tunnel test was conducted in the NASA Langley Research Center s 20-Inch Mach 6 Air Tunnel in support of the Hypersonic International Flight Research Experimentation Program. The information in this report is focused on the Flight 1 configuration, the first in a series of flight experiments. This report documents experimental measurements made over a range of Reynolds numbers and angles of attack on several scaled ceramic heat transfer models of the Flight 1 payload. Global heat transfer was measured using phosphor thermography and the resulting images and heat transfer distributions were used to infer the state of the boundary layer on the vehicle windside and leeside surfaces. Boundary layer trips were used to force the boundary layer turbulent, and a brief study was conducted to determine the effectiveness of the trips with various heights. The experimental data highlighted in this test report were used to size and place the boundary layer trip for the flight test vehicle.

Berger, Karen T.↗

NASA NTRS2018

MISR-GOES 3D Winds: Implications for Future LEO-GEO and LEO-LEO Winds

Global wind observations are fundamental for studying weather and climate dynamics and for operational forecasting. Most wind measurements come from atmospheric motion vectors (AMVs) by tracking the displacement of cloud or water vapor features. These AMVs generally rely on thermal infrared (IR) techniques for their height assignments, which are subject to large uncertainties in the presence of weak or reversed vertical temperature gradients near the planetary boundary layer (PBL)and tropopause folds. Stereo imaging can overcome the height assignment problem using geometric parallax for feature height determination. In this study we develop a stereo 3D-Wind algorithm to simultaneously retrieve AMV and height from geostationary (GEO) and low Earth orbit (LEO) satellite imagery and apply it to collocated Geostationary Operational Environmental Satellite (GOES)and Multi-angle Imaging SpectroRadiometer (MISR) imagery. The new algorithm improves AMV and height relative to products from GOES or MISR alone, with an estimated accuracy of <0.5 m/s in AMV and <200 m in height with 2.2 km sampling. The algorithm can be generalized to other LEO-GEO or LEO-LEO combinations for greater spatiotemporal coverage. The technique demonstrated with MISR and GOES has important implications for future high-quality AMV observations, for which a low-cost constellation of CubeSats can play a vital role.

MISR↗

NASA NTRSDate not supplied

Latest Progress and Results in LEO-GEO and GEO-GEO Stereo AMVs

Atmospheric motion vectors (AMVs), derived by tracking patterns, represent the winds in a layer characteristic of the pattern. AMV height (or pressure), important for applications in atmospheric research and operational meteorology, is usually assigned using observed IR brightness temperatures with a modeled atmosphere and can be inaccurate. Stereoscopic tracking provides a direct geometric height measurement of the pattern that an AMV represents. We extend our previous work with multi-angle imaging spectro–radiometer (MISR) and GOES to moderate resolution imaging spectroradiometer (MODIS) and the GOES-R series advanced baseline imager (ABI). MISR is a unique satellite instrument for stereoscopy with nine angular views along track, but its images have a narrow (380 km) swath and no thermal IR channels. MODIS provides a much wider (2330 km) swath and eight thermal IR channels that pair well with all but two ABI channels, offering a rich set of potential applications. Given the similarities between MODIS and VIIRS, our methods should also yield similar performance with VIIRS. Our methods, as enabled by advanced sensors like MODIS and ABI, require high-accuracy geographic registration in both systems but no synchronization of observations. AMVs are retrieved jointly with their heights from the disparities between triplets of ABI scenes and the paired MODIS granule. We validate our retrievals against MISR-GOES retrievals, operational GOES wind products, and by tracking clear-sky terrain. We demonstrate that the 3D-wind algorithm can produce high-quality AMV and height measurements for applications from the planetary boundary layer (PBL) to the upper troposphere, including cold-air outbreaks, wildfire smoke plumes, and hurricanes.

Atmospheric motion vectors↗

NASA NTRS2019

Joint 3D-Wind Retrievals with Stereoscopic Views from MODIS and GOES

Atmospheric motion vectors (AMVs), derived by tracking patterns, represent the winds in a layer characteristic of the pattern. AMV height (or pressure), important for applications in atmospheric research and operational meteorology, is usually assigned using observed IR brightness temperatures with a modeled atmosphere and can be inaccurate. Stereoscopic tracking provides a direct geometric height measurement of the pattern that an AMV represents. We extend our previous work with multi-angle imaging spectroradiometer (MISR) and GOES to moderate resolution imaging spectroradiometer (MODIS) and the GOES-R series advanced baseline imager (ABI). MISR is a unique satellite instrument for stereoscopy with nine angular views along track, but its images have a narrow (380 km) swath and no thermal IR channels. MODIS provides a much wider (2330 km) swath and eight thermal IR channels that pair well with all but two ABI channels, o e ring a rich set of potential applications. Given the similarities between MODIS and VIIRS, our methods should also yield similar performance with VIIRS. Our methods, as enabled by advanced sensors like MODIS and ABI, require high-accuracy geographic registration in both systems but no synchronization of observations. AMVs are retrieved jointly with their heights from the disparities between triplets of ABI scenes and the paired MODIS granule. We validate our retrievals against MISR-GOES retrievals, operational GOES wind products, and by tracking clear-sky terrain. We demonstrate that the 3D-wind algorithm can produce high-quality AMV and height measurements for applications from the planetary boundary layer (PBL) to the upper troposphere, including cold-air outbreaks, wildfire smoke plumes, and hurricanes.

Carr, James L.↗

NASA NTRS1987

Boundary-layer instability mechanisms on a swept-leading edge at Mach 3.5

Correlations have been made in NASA Langley's Mach 3.5 Pilot Quiet Tunnel for the transitions occurring from laminar to turbulent flow, in the cases of 45-deg and 60-deg swept cylinders. While freestream noise variations had no effect on boundary layer transition, the addition of boundary layer trips to the leading edges led to transition at lower Re numbers, depending on both trip height and wind tunnel noise level. Also presented are the results of compressible linear stability calculations for the boundary layer of an infinite swept cylinder; Tollmien-Schlichting waves are found to be amplified in the attachment line boundary layer.

Creel, T. R., Jr.↗

NASA NTRS1990

A review of vortex structures and associated coherent motions in turbulent boundary layers

The experimental and computational evidence for the existence and role of vortices in turbulent boundary layers is briefly reviewed. Quasi-streamwise and transverse vortices are considered, and various published conceptual models for horseshoe-like vortical structures are compared. The causes for upright and inverted horseshoe-shaped vorticity lines are discussed, and the distinction between vorticity lines and vortices is demonsrated. Finally, results from a numerically-simulated turbulent boundary layer are used to compute distributions of diameter, height, and strength for quasi-streamwise and spanwise vortices. These results confirm that quasi-streamwise vortices are clustered near the wall, while spanwise vortices are distributed throughout the layer. The variation of spanwise vortex core diameter with distance from the wall is found to be consistent with the mixing-length distribution for a boundary layer.

Robinson, Stephen K.↗

NASA NTRS1986

Smoothed Two-Dimensional Edges for Laminar Flow

New concept allows passive method for installing flaps, slats, iceprotection equipment, and other leading-edge devices on natural-laminar-flow (NLF) wings without causing loss of laminar flow. Two-dimensional roughness elements in laminar boundary layers strategically shaped to increase critical (allowable) height of roughness. Facilitates installation of leading-edge devices by practical manufacturing methods.

Holmes, B. J.↗

NASA NTRS1984

Numerical Modeling of the Atmosphere

Numerical models and numerical analyses of observations were used to improve the understanding of the physical processes important in global weather and climate. Results from a study of the effect of baroclinic waves on mid-latitude vertical temperature structure show that the waves' vertical eddy heat flux tend to eliminate the potential vorticity gradient near the steering level by causing the static stability to decrease rapidly with height in the lower troposphere above the boundary layer. An empirical study of the relationship between eddy heat fluxes and the meridional temperature gradient has been completed. The results indicate that the feedback in the flux-gradient system is comparable to dissipation on all time scales between the synoptic and the seasonal. The definition of the Eliassen-Palm flux and the Eliassen-Palm and non-acceleration theorems has been generalized to include eddy forcing of condensation. Calculations based on the generalized diagnostics showed that the annual mean eddy forcing of the zonal mean zonal wind is two and one half times stronger when the condensation effects are included.

Stone, P. H.↗