Search NASA⌕ Search

SEARCH · Search NASA

Results for “conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Challenges of Cold Conditioning and Static Testing the Second Ares Demonstration Motor (DM-2)

On August 31, 2010, a five-segment demonstration motor (DM) for the Ares program was successfully tested. A series of demonstration motors (DMs) will be tested in different conditioned environments to confirm they meet their design specifications. The second demonstration motor (DM-2) was the first cold motor. The motor needed to be subjected to sub-freezing temperatures for two months so that its internal propellant mean bulk temperature (PMBT) was approximately 40 F. Several challenges had to be overcome to make this a successful test. One challenge was to condition four field joints to get the O-rings approximately 32 F. This would be done by applying conditioning shrouds to externally cool each field joint after the test bay was pulled off. The purpose of this conditioning was to validate the new O-ring design and allow joint heaters to be eliminated. Another challenge was maintaining temperature requirements for components in the nozzle vectoring system. A separate heating system was used to warm these components during cold conditioning. There were 53 test objectives that required 764 channels of data to be recorded; 460 were specific to DM-2. This instrumentation had to be installed prior to conditioning, which meant the baseline process and timeline had to be modified to meet this time critical schedule.

Quinn, Shyla↗
NASA NTRS2012

Effect of Inflow Boundary Conditions on Hovering Tilt-Rotor Flows

A study on the effect of inflow turbulence boundary conditions on the local flow on and around a body in flight has been carried out. The study has been carried out using OVERFLOW2 flow solver using the default Spalart-Allmaras turbulence model in OVERFLOW. Many OVERFLOW turbulent flow simulations have been reported using the SA-fv3 model1 over the years. The present study demonstrates that the turbulence levels imposed as a boundary condition (b.c.) in the far-field as implemented in OVERFLOW are not correct. In fact, very low level of turbulence at the far-field boundary as implemented in OVERFLOW results in the SA-fv3 model predicting transition-like profiles on a given body. By choosing sufficiently high levels of the Reynolds number of turbulence, Rt, as a boundary condition, this anomalous behavior of SA-fv3 model is eliminated. Since numerous papers using OVERFLOW have been presented in the literature including that by the author2 using low level of inflow turbulence, it will be beneficial to the CFD community at large and in particular to the OVERFLOW community to understand this effect of the inflow b.c. in the SA-fv3 model. Various results reported over the years in domains such as high-lift applications, drag prediction applications and rotorcraft flow applications can be revisited using the new turbulence inflow boundary condition prescription as suggested in this study. It has been demonstrated in the literature that the effect of inflow turbulence level on the downstream development of flow is too important to be ignored. Demonstrative results are shown and compared with experiment for the case of hovering XV-15 rotor flow at a tip Reynolds number of 4.9 x 10(exp 6) and Mach number of 0.69 in Figs. 1 and 2 below. Fig. 1(a,b) shows skin friction predictions at radial station of r/R = 0.28 corresponding to 5 different inflow boundary conditions obtained with the SA-fv3 model. As the inflow turbulence is increased monotonically, from a value of Rt = 0.1 to 100.0 as shown in Fig. 1, a fully developed turbulent skin friction profile is realized progressively as shown in Fig. 1(b). Similarly skin friction results shown in Fig. 2(a,b) corresponding to radial stations of r/R = 0.72 reinforce the postulate made here that as the inflow turbulence level is increased gradually, fully turbulent on-the-blade simulation is realized uniformly. In the full paper extensive results on skin friction, pressure and velocity profiles as well as the Figure of Merit will be presented and compared with experiment that will illustrate the substantial effect of the inflow boundary conditions on the development of hovering rotor flow downstream.

Kaul, Upender K.↗
NASA NTRS2014

Alteration of Basaltic Glass to Mg/Fe-Smectite under Acidic Conditions: A Potential Smectite Formation Mechanism on Mars

Phyllosilicates of the smectite group including Mg- and Fe-saponite and Fe(III)-rich nontronite have been identified on Mars. Smectites are believed to be formed under neutral to alkaline conditions that prevailed on early Mars. This hypothesis is supported by the observation of smectite and carbonate deposits in Noachian terrain on Mars. However, smectite may have formed under mildly acidic conditions. Abundant smectite formations have been detected as layered deposits hundreds of meters thick in intracrater depositional fans and plains sediments, while no large deposits of carbonates are found. Development of mildly acidic conditions at early Mars might allow formation of smectite but inhibit widespread carbonate precipitation. Little is known regarding the mechanisms of smectite formation from basaltic glass under acidic conditions. The objective of this study was to test a hypothesis that Mars-analogue basaltic glass alters to smectite minerals under acidic conditions (pH 4). The effects of Mg and Fe concentrations and temperature on smectite formation from basaltic glass were evaluated. Phyllosilicate synthesis was performed in batch reactors (Parr acid digestion vessel) under reducing hydrothermal conditions at 200 C and 100 C. Synthetic basaltic glass with a composition similar to that of the Gusev crater rock Adirondack (Ground surface APXS measurement) was used in these experiments. Basaltic glass was prepared by melting and quenching procedures. X-ray diffraction (XRD) analysis indicated that the synthesized glass was composed of olivine, magnetite and X-ray amorphous phase. Samples were prepared by mixing 250 mg Adirondack with 0.1 M acetic acid (final pH 4). In order to study influence of Mg concentration on smectite formation, experiments were performed with addition of 0, 1 and 10 mM MgCl2. After 1, 7 and 14 day incubations the solution composition was analyzed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and the altered glass and formed phyllosilicates were examined by XRD analysis. Mineralogical changes were significant in Adirondack incubated with 10 mM MgCl2 at pH 4 and heated at 200 C. X-ray diffraction analysis revealed formation of phyllosilicate during 14 day incubation (Figure 1). Smectite was confirmed as the phyllosilicate after treatments with glycerol and KCl and heating to 550 C. The position of 02l (4.60 A) and 060 (1.54 A) diffraction bands were indicative of trioctahedral smectite such as saponite. Analysis of solution composition demonstrated that aqueous concentration of Mg decreased from 10 mM to approx.4 mM after 7 day incubation likely due to saponite formation. Smectite also formed in Adirondack incubated with 0 mM MgCl2 at pH 4 and heated at 200 C. However, diffraction peak positions of 02l (4.52 A) and 060 (1.51 A) suggested formation of dioctahedral nontronite. The 100degC Mg and Fe(II) treated basaltic glass experiments are ongoing and results will be presented.

Peretyazhko, Tanya↗
NASA NTRS2014

Investigation of Spiral Bevel Gear Condition Indicator Validation Via AC-29-2C Using Damage Progression Tests

This report documents the results of spiral bevel gear rig tests performed under a NASA Space Act Agreement with the Federal Aviation Administration (FAA) to support validation and demonstration of rotorcraft Health and Usage Monitoring Systems (HUMS) for maintenance credits via FAA Advisory Circular (AC) 29-2C, Section MG-15, Airworthiness Approval of Rotorcraft (HUMS) (Ref. 1). The overarching goal of this work was to determine a method to validate condition indicators in the lab that better represent their response to faults in the field. Using existing in-service helicopter HUMS flight data from faulted spiral bevel gears as a "Case Study," to better understand the differences between both systems, and the availability of the NASA Glenn Spiral Bevel Gear Fatigue Rig, a plan was put in place to design, fabricate and test comparable gear sets with comparable failure modes within the constraints of the test rig. The research objectives of the rig tests were to evaluate the capability of detecting gear surface pitting fatigue and other generated failure modes on spiral bevel gear teeth using gear condition indicators currently used in fielded HUMS. Nineteen final design gear sets were tested. Tables were generated for each test, summarizing the failure modes observed on the gear teeth for each test during each inspection interval and color coded based on damage mode per inspection photos. Gear condition indicators (CI) Figure of Merit 4 (FM4), Root Mean Square (RMS), +/- 1 Sideband Index (SI1) and +/- 3 Sideband Index (SI3) were plotted along with rig operational parameters. Statistical tables of the means and standard deviations were calculated within inspection intervals for each CI. As testing progressed, it became clear that certain condition indicators were more sensitive to a specific component and failure mode. These tests were clustered together for further analysis. Maintenance actions during testing were also documented. Correlation coefficients were calculated between each CI, component, damage state and torque. Results found test rig and gear design, type of fault and data acquisition can affect CI performance. Results found FM4, SI1 and SI3 can be used to detect macro pitting on two more gear or pinion teeth as long as it is detected prior to progressing to other components or transitioning to another failure mode. The sensitivity of RMS to system and operational conditions limit its reliability for systems that are not maintained at steady state. Failure modes that occurred due to scuffing or fretting were challenging to detect with current gear diagnostic tools, since the damage is distributed across all the gear and pinion teeth, smearing the impacting signatures typically used to differentiate between a healthy and damaged tooth contact. This is one of three final reports published on the results of this project. In the second report, damage modes experienced in the field will be mapped to the failure modes created in the test rig. The helicopter CI data will then be re-processed with the same analysis techniques applied to spiral bevel rig test data. In the third report, results from the rig and helicopter data analysis will be correlated. Observations, findings and lessons learned using sub-scale rig failure progression tests to validate helicopter gear condition indicators will be presented.

gears↗
NASA NTRS2014

Investigation of Spiral Bevel Gear Condition Indicator Validation via AC-29-2C Using Fielded Rotorcraft HUMS Data

This report presents the analysis of gear condition indicator data collected on a helicopter when damage occurred in spiral bevel gears. The purpose of the data analysis was to use existing in-service helicopter HUMS flight data from faulted spiral bevel gears as a Case Study, to better understand the differences between HUMS data response in a helicopter and a component test rig, the NASA Glenn Spiral Bevel Gear Fatigue Rig. The reason spiral bevel gear sets were chosen to demonstrate differences in response between both systems was the availability of the helicopter data and the availability of a test rig that was capable of testing spiral bevel gear sets to failure. The objective of the analysis presented in this paper was to re-process helicopter HUMS data with the same analysis techniques applied to the spiral bevel rig test data. The damage modes experienced in the field were mapped to the failure modes created in the test rig. A total of forty helicopters were evaluated. Twenty helicopters, or tails, experienced damage to the spiral bevel gears in the nose gearbox. Vibration based gear condition indicators data was available before and after replacement. The other twenty tails had no known anomalies in the nose gearbox within the time frame of the datasets. These twenty tails were considered the baseline dataset. The HUMS gear condition indicators evaluated included gear condition indicators (CI) Figure of Merit 4 (FM4), Root Mean Square (RMS) or Diagnostic Algorithm 1 (DA1) and +/- 3 Sideband Index (SI3). Three additional condition indicators, not currently calculated on-board, were calculated from the archived data. These three indicators were +/- 1 Sideband Index (SI1), the DA1 of the difference signal (DiffDA1) and the peak-to-peak of the difference signal (DP2P). Results found the CI DP2P, not currently available in the on-board HUMS, performed the best, responding to varying levels of damage on thirteen of the fourteen helicopters evaluated. Two additional CIs also not in the on-board system, DiffDA1and SI1, also performed well responding to twelve and ten of the fourteen helicopters evaluated respectively. Of the three CIs currently available in the MSPU, DA1, FM4 and SI3, SI3, responded to eight, DA1 responded to six and FM4 responded to four of the fourteen helicopters evaluated. FM4, the poorest performing CI, was not as responsive to damage as the other five CIs. Conversely, when compared to the other two, it was the only CI that responded to damage on two helicopters. CI response could not be correlated to specific failure modes due to limited pictures and subjective descriptions found within the TDA. Flight regime did affect CI response to some gear faults. Due to the range of operating conditions for each regime, more studies are required to determine their sensitivity to regimes.

rotorcraft↗
NASA NTRS2016

The Cr Redox Record of fO2 Variation in Angrites. Evidence for Redox Conditions of Angrite Petrogenesis and Parent Body

Angrites represent some of the earliest stages of planetesimal differentiation. Not surprisingly, there is no simple petrogenetic model for their origin. Petrogenesis has been linked to both magmatic and impact processes. Studies demonstrated that melting of chondritic material (e.g. CM, CV) at redox conditions where pure iron metal is unstable (e.g., IW+1 to IW+2) produced angrite-like melts. Alternatively, angrites were produced at more reducing conditions (<IW) with their exotic melt compositions resulting from carbonates in the source or from nebular condensation. Clearly, understanding what role fO2 plays in producing angrite magmas is critical for deciphering their petrogenesis and extending our understanding of primordial melting of asteroids. Calculations for the fO2 conditions of angrite crystallization are limited, and only preliminary attempts been made to understand the changes in fO2 that occurred during petrogenesis. Many of the angrites have phase assemblages which provide conflicting signals about redox conditions during crystallization (e.g., Fe metal and a Fe-Ti oxide with potential Fe3+. There have been several estimates of fO2 for angrites. Most notably, experiments examined the variation of DEu/DGd with fO2, between plagioclase and fassaitic pyroxene in equilibrium with an angrite melt composition. They used their observations to estimate the fO2 of crystallization to be approximately IW+0.6 for angrite LEW 86010. This estimate is only a "snapshot" of fO2 conditions during co-crystallization of plagioclase and pyroxene. Preliminary XANES analyses of V redox state in pyroxenes from D'Orbigny reported changes in fO2 from IW-0.7 during early pyroxene crystallization to IW+0.5 during latter episodes of pyroxene crystallization [15]. As this was a preliminary report, it presented limited information concerning the effects of pyroxene orientation and composition on the V valence measurements, and the effect of melt composition on valence and partitioning behavior of V. A closer examination of fO2 as recorded by Cr valence state in olivine will allow us to test models for primordial melting of chondritic material to produce the angrite parent melts. Here, we report the our initial stages of examining the origin and conditions of primordial melting on the angrite parent body and test some of the above models by integrating an experimental study of Cr and V valence partitioning between olivine [OL] and an angrite melt, with micro-scale determinations of Cr and V oxidation state in OL in selected "volcanic" angrites.

Shearer, Charles K.↗
NASA NTRS2016

The Effects of Ambient Conditions on Helicopter Harmonic Noise Radiation: Theory and Experiment

The effects of ambient atmospheric conditions, air temperature and density, on rotor harmonic noise radiation are characterized using theoretical models and experimental measurements of helicopter noise collected at three different test sites at elevations ranging from sea level to 7000 ft above sea level. Significant changes in the thickness, loading, and blade-vortex interaction noise levels and radiation directions are observed across the different test sites for an AS350 helicopter flying at the same indicated airspeed and gross weight. However, the radiated noise is shown to scale with ambient pressure when the flight condition of the helicopter is defined in nondimensional terms. Although the effective tip Mach number is identified as the primary governing parameter for thickness noise, the nondimensional weight coefficient also impacts lower harmonic loading noise levels, which contribute strongly to low frequency harmonic noise radiation both in and out of the plane of the horizon. Strategies for maintaining the same nondimensional rotor operating condition under different ambient conditions are developed using an analytical model of single main rotor helicopter trim and confirmed using a CAMRAD II model of the AS350 helicopter. The ability of the Fundamental Rotorcraft Acoustics Modeling from Experiments (FRAME) technique to generalize noise measurements made under one set of ambient conditions to make accurate noise predictions under other ambient conditions is also validated.

Greenwood, Eric↗
NASA NTRS2016

Impact of Flight Enthalpy, Fuel Simulant, and Chemical Reactions on the Mixing Characteristics of Several Injectors at Hypervelocity Flow Conditions

The high total temperatures or total enthalpies required to duplicate the high-speed flight conditions in ground experiments often place stringent requirements on the material selection and cooling needs for the test articles and intrusive flow diagnostic equipment. Furthermore, for internal flows, these conditions often complicate the use of nonintrusive diagnostics that need optical access to the test section and interior portions of the flowpath. Because of the technical challenges and increased costs associated with experimentation at high values of total enthalpy, an attempt is often made to reduce it. This is the case for the Enhanced Injection and Mixing Project (EIMP) currently underway in the Arc-Heated Scramjet Test Facility at the NASA Langley Research Center. The EIMP aims to investigate supersonic combustion ramjet (scramjet) fuel injection and mixing physics, improve the understanding of underlying physical processes, and develop enhancement strategies and functional relationships between mixing performance and losses relevant to flight Mach numbers greater than 8. The experiments will consider a "direct-connect" approach and utilize a Mach 6 nozzle to simulate the combustor entrance flow of a scramjet engine. However, while the value of the Mach number is matched to that expected at the combustor entrance in flight, the maximum value of the total enthalpy for these experiments is limited by the thermal-structural limits of the uncooled experimental hardware. Furthermore, the fuel simulant is helium, not hydrogen. The use of "cold" flows and non-reacting mixtures of fuel simulants for mixing experiments is not new and has been extensively utilized as a screening technique for scramjet fuel injectors. In this study, Reynolds-averaged simulations are utilized (RAS) to systematically verify the implicit assumptions used by the EIMP. This is accomplished by first performing RAS of mixing for two injector configurations at planned nominal experimental conditions. The mixing parameters of interest, such as mixing efficiency and total pressure recovery, are then computed and compared to the values obtained from RAS under the true enthalpy conditions and using helium and hydrogen. Finally, the impact of combustion on mixing, often deemed small enough to neglect at hypervelocity conditions, is assessed by comparing the results obtained from the hydrogen-fueled reacting and non-reacting RAS. For reacting flows, in addition to mixing efficiency and total pressure recovery, the combustion efficiency and thrust potential are also considered. In all of the simulations, the incoming air Mach number and the fuel-to-air ratio are the same, while the total pressure, total enthalpy, and the fuel simulant vary depending on the case considered. It is found that under some conditions the "cold" flow experiments are a good approximation of the flight.

Drozda, Tomasz G.↗
NASA NTRS2017

Characterization of a Pressure-Fed LOX/LCH4 Reaction Control System Under Simulated Altitude and Thermal Vacuum Conditions

A liquid oxygen, liquid methane (LOX/LCH4) reaction control system (RCS) was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under simulated altitude and thermal vacuum conditions. The RCS is a subsystem of the Integrated Cryogenic Propulsion Test Article (ICPTA) and was initially developed under Project Morpheus. Composed of two 28 lbf-thrust and two 7 lbf-thrust engines, the RCS is fed in parallel with the ICPTA main engine from four propellant tanks. 40 tests consisting of 1,010 individual thruster pulses were performed across 6 different test days. Major test objectives were focused on system dynamics, and included characterization of fluid transients, manifold priming, manifold thermal conditioning, thermodynamic vent system (TVS) performance, and main engine/RCS interaction. Peak surge pressures from valve opening and closing events were examined. It was determined that these events were impacted significantly by vapor cavity formation and collapse. In most cases the valve opening transient was more severe than the valve closing. Under thermal vacuum conditions it was shown that TVS operation is unnecessary to maintain liquid conditions at the thruster inlets. However, under higher heat leak environments the RCS can still be operated in a self-conditioning mode without overboard TVS venting, contingent upon the engines managing a range of potentially severe thermal transients. Lastly, during testing under cold thermal conditions the engines experienced significant ignition problems. Only after warming the thruster bodies with a gaseous nitrogen purge to an intermediate temperature was successful ignition demonstrated.

Atwell, Matthew J.↗
NASA NTRS2019

Validation of Proposed Go-Around Criteria Under Various Environmental Conditions

This paper evaluates the effects of environmental conditions on touchdown performance under varying approach states and validates proposed go-around criteria developed using data from a previously conducted study under these various environmental conditions. An experiment was conducted using Boeing 737-800 and Airbus A330-200 Level D full-flight simulators in which 24 pilots flew multiple approaches under different approach conditions and environmental variables. Pilots were instructed to always land the aircraft, even from conditions considered to be an unstable approach. Various touchdown performance metrics were analyzed. In addition, pilots’ perceptions of risk under the various unstable approach conditions and resulting landings were assessed. The results of the study revealed that wind speed/direction and visibility had a stronger effect on touchdown performance than the approach parameters. Specifically, wind had a highly significant effect on longitudinal and lateral touchdown point, as well as a significant effect on sink-rate at touchdown. Wind and visibility, along with localizer deviation, also had a strong effect on pilots’ perception of risk and workload ratings. Furthermore, the study confirmed that touchdown performance was similar among the runs with a 300-foot and 500-foot starting gate, as was found in the previously conducted experiment. These results support the previous finding that lowering the go-around decision gate to 300-foot might be acceptable, but suggest that certain environmental conditions might warrant altered thresholds of the proposed go-around criteria at this gate. Finally, the findings of this experiment highlight the importance of environmental factors in the assessment of risk of unwanted outcomes on approach and landing.

Transport Aircraft↗
NASA NTRSDate not supplied

Risk Assessment of Obstacle Collision for UAVs under off-nominal conditions

Enabling operations of unmanned aerial vehicles (UAVs) in low-altitude airspace, demands the need of robust risk monitoring framework for assessing the safety of airspace, ground-structures and people. As widespread applications emerge, the need of risk assessment becomes increasingly important for UAV flights beyond visual line-of-sight, especially subjected to off-nominal conditions introduced by component failures, degraded controllability or environmental disturbances such as wind gusts in an urban canyon. From a safety perspective, collision with obstacles can be detrimental not only to the vehicle and payload, but also to the structure and people on ground. Although it is safe to assume that approved UAVs would be equipped with collision avoidance systems, risk of collision which can be predicted for a flight trajectory even before the UAV encounters any obstacle is beneficial to resolve contingencies in its decision-making under off-nominal conditions. In this paper, a framework is presented for computing the risk of collision with obstacle based on a UAV's predicted trajectory, proximity to static and dynamic obstacles, sub-system state-of-health and external wind conditions. The conditional probability of trajectory deviation is generated using a Bayesian Belief Network (BBN) based on on-board sensor measurements. Further, a kinematic 3-DOF model is implemented to compute deviation in UAV's trajectory subjected to one case study of off-nominal condition i.e. wind gusts. Finally, the integrated risk factor is demonstrated on real data from experimental flights of an octocopter at NASA Langley Research Center, in presence of simulated obstacles and wind conditions. The proposed approach would enable risk-informed decision making process for timely mitigation of current and future unsafe events.

Portia Banerjee↗
NASA NTRSDate not supplied

Risk Assessment of Obstacle Collision for UAVs under Off-nominal Conditions

Enabling operations of unmanned aerial vehicles (UAVs) in low-altitude airspace demands the need of robust risk monitoring framework for assessing the safety of airspace, ground structures and people. As widespread applications emerge, the need of risk assessment becomes increasingly important for UAV flights beyond visual line-of-sight, especially subjected to off-nominal conditions introduced by component failures, degraded controllability or environmental disturbances such as wind gusts in an urban canyon. From a safety perspective, collision with obstacles can be detrimental not only to the vehicle and payload, but also to the structure and people on ground. Although it is safe to assume that approved UAVs would be equipped with collision avoidance systems, risk of collision which can be predicted for a flight trajectory even before the UAV encounters any obstacle is beneficial to resolve contingencies in its decision-making under off-nominal conditions. In this paper, a framework is presented for computing the risk of collision with obstacle based on a UAV’s predicted trajectory, proximity to static and dynamic obstacles, sub-system state-of-health and external wind conditions. The conditional probability of trajectory deviation is generated using a Bayesian Belief Network (BBN) based on on-board sensor measurements. Further, a kinematic 3-DOF model is implemented to compute deviation in UAV’s trajectory subjected to one case study of off-nominal condition i.e. wind gusts. Finally, the integrated risk factor is demonstrated on real data from experimental flights of an octocopter at NASA Langley Research Center, in presence of simulated obstacles and wind conditions. The proposed approach would enable risk-informed decision making process for timely mitigation of current and future unsafe events.

Bayesian network↗
NASA NTRS2023

Effects of Ambient Conditions on Helicopter Harmonic Noise Radiation: Theory and Experiment

The effects of ambient atmospheric conditions, air temperature, and density on rotor harmonic noise radiation are characterized using theoretical models and experimental measurements of helicopter noise collected at three different test sites at elevations ranging from sea level to 7000 ft above sea level. Significant changes in the thickness, loading, and blade–vortex interaction noise levels and radiation directions are observed across the different test sites for an AS350 helicopter flying at the same indicated airspeed and gross weight. However, the radiated noise is shown to scale with ambient pressure when the flight condition of the helicopter is defined in nondimensional terms. Although the effective tip Mach number is identified as the primary governing parameter for thickness noise, the nondimensional weight coefficient also impacts lower harmonic loading noise levels, which contribute strongly to low-frequency harmonic noise radiation both in and out of the plane of the horizon. Strategies for maintaining the same nondimensional rotor operating condition under different ambient conditions are developed using an analytical model of single main rotor helicopter trim and confirmed using a CAMRAD II model of the AS350 helicopter. The ability of the Fundamental Rotorcraft Acoustics Modeling from Experiments (FRAME) technique to generalize noise measurements made under one set of ambient conditions to make accurate noise predictions under other ambient conditions is also validated.

rotorcraft↗
DOE OSTI2022

Imposition of local boundary conditions in peridynamics without a fictitious layer and unphysical stress concentrations

Here, this study introduces a general approach for the imposition of local boundary conditions in non- ordinary state-based peridynamics (NOSB PD) to eliminate the displacement kinks near the boundary without a fictitious layer under quasi-static loading conditions. It identifies the underlying reason for the unphysical displacement kinks. Under an imposed linear displacement field, the NOSB PD equilibrium equation is not satisfied near the boundary due to the unsymmetric horizon of material points. However, the equilibrium equation derived by using the PD differential operator is satisfied at such material points. Therefore, the material body is divided into three regions to satisfy the equilibrium equations and to impose displacement and tractions boundary conditions. This approach does not deviate from the original NOSB PD; however, it provides a simple solution to eliminate the displacement kink near the boundary, which leads to unphysical stress concentrations. Its efficacy is demonstrated by considering elastic rectangular and square plates subjected to various types of boundary conditions leading to homogeneous as well as nonhomogeneous deformations. The creep response of a rectangular plate further proves the robustness of the present approach. Also, a quasi-static crack propagation from a pre-existing crack in a square plate under mode-I, mode-II and mixed-mode loading conditions demonstrates its capability for failure prediction based on the critical stretch criteria. Finally, its applicability for 3D analysis is demonstrated by considering a rectangular prism under applied stretch and normal stress.

42 ENGINEERING↗
DOE OSTI2026

Multi-Objective design of interlocking metasurfaces using conditional diffusion models

Unit cell design remains a major challenge for interlocking metasurfaces, a promising joining technology for dissimilar materials, due to the complex, competing, multivariate design space and the need for rapid adaptation to varying performance requirements. This study explores Conditional Diffusion Models as a design optimization tool for interlocking metasurfaces. Given the complex, competing, multivariate design space for interlocking metasurfaces, unit cell design remains a major challenge for this joining technology. We trained a conditional diffusion model on 25,000 finite element analysis-simulated interlocking metasurface unit cells to generate designs with tailored thermo-mechanical properties (tensile strength, shear strength, and thermal conductivity) based on specified performance criteria. The model demonstrated a success rate of approximately 72 % in producing designs that met specified property bounds. The conditional diffusion model generated both thermally resistive and conductive designs, revealing clear trends in design characteristics: taller, dendritic structures were advantageous for tensile loads, while shorter, robust designs excelled in shear applications. Our findings indicate that the model's performance is more influenced by the breadth of the design space than by the quantity of training data, highlighting the importance of expansive design domains for generating innovative solutions. This work establishes conditional diffusion models as a highly efficient and adaptable tool for rapid interlocking metasurface unit cell design, paving the way for advancements in multi-material joining technologies, as well as highlighting the justification to leverage conditional diffusion models as design tools across complex design domains.

Conditional diffusion models↗
DOE OSTI2021

A Poisson equation method for prescribing fully developed non-Newtonian inlet conditions for computational fluid dynamics simulations in models of arbitrary cross-section

Prescribing inlet boundary conditions for computational fluid dynamics (CFD) simulations of internal flow in complex geometries such as anatomical vascular models is challenging. In the absence of patient-specific inlet velocity data, a common approach for long blood vessels is to assume that the inlet flow is fully developed. In vessels of irregular cross section, however, prescribing fully developed conditions is complicated due to the lack of a general closed-form analytical solution. In this study, we develop a simple Poisson equation method for prescribing fully developed inlet conditions for the flow of either Newtonian or non-Newtonian fluids in CFD models of arbitrary cross-section. We first derive the generalized Poisson equation for fully developed flow of a non-Newtonian fluid and we then develop and verify a methodology for numerically computing the solution on any planar boundary domain. In addition, we develop a simple extension of the method for prescribing a non-orthogonal inlet velocity that represents fully developed flow from an upstream tube that is connected to the CFD inlet at a non-orthogonal angle. This may be used to investigate a common source of uncertainty in CFD simulations of internal flow that is due to a lack of information concerning the exact streamwise flow direction at the inlets. Comparison to several Newtonian and non-Newtonian benchmark verification solutions shows the method to be extremely accurate. As a practical demonstration case, we use the method to prescribe fully developed conditions on multiple non-circular inlets for the non-Newtonian flow of blood in a patient-specific model of the inferior vena cava (IVC). Finally, we further demonstrate the utility of the method by performing a sensitivity study using the patient-specific IVC model, wherein we investigate the influence of inlet velocity flow direction on the non-Newtonian IVC hemodynamics. Given its simplicity and computational efficiency, the method is shown to be far superior to alternative approaches for prescribing fully developed inlet conditions in such complicated geometries. In conclusion, to facilitate the adoption of our Poisson equation method, we have distributed our OpenFOAM source code and the associated test cases from this study as open-source software.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Precision Structure Engineering of High-Entropy Oxides under Ambient Conditions

High-entropy oxides (HEOs) have unveiled a unique frontier in the realm of heterogeneous catalysis, taking advantage of the entropic effect and increased complexities to deliver ultrahigh stability and large tuning capability. However, current HEO synthesis mainly relies on high-temperature annealing approaches affording HEOs possessing no or low surface area, inferior active site exposure efficiency, and low controllability over the structure tuning. The grand challenge lies in producing high-quality HEO catalysts with high active site utilization efficiency, which relies on precision structure engineering, preferably under mild conditions. In this work, an in situ lattice engineering approach was developed to afford a supported HEO catalyst under ambient conditions. The HEO compositions (CuCoFeNiMnO x ) were uniformly integrated into the lattice of CeO 2 driven by cavitation-induced nucleation being generated via ultrasonication. The as-afforded catalysts were featured by high surface area, atomically dispersed HEO compositions, active redox properties, abundant oxygen vacancies (O V ), antiagglomeration, and high phase stability under harsh conditions. Compared with the ex situ introduction of HEO on the surface, the in situ method provides dual benefits to maintain the dispersity of HEO via entropic and lattice confinement effects. Engineering the complex HEO within the lattice of fluorite-structured CeO 2 also yields abundant defects (e.g., O V ) and active metal sites with strong reducing properties (e.g., Ce 3+ and Cu + ), which greatly improves the activity of the lattice oxygen and tunability of the adsorption behavior of the guest molecules, especially in the presence of impurities (e.g., water and propane). The catalytic performance of the supported HEO catalyst in oxidative procedures surpasses the pure dense phase HEO as well as the ex situ-generated catalysts. Further, the synthesis approach being developed in this work, together with the fundamental understanding in structure evolution and reaction mechanism, showcases a facile pathway under ambient conditions to generate stable catalysts capable of maintaining structural robustness in high-temperature conditions while delivering enhanced catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Deep transfer operator learning for partial differential equations under conditional shift

Transfer learning enables the transfer of knowledge gained while learning to perform one task (source) to a related but different task (target), hence addressing the expense of data acquisition and labelling, potential computational power limitations and dataset distribution mismatches. Here, we propose a new transfer learning framework for task-specific learning (functional regression in partial differential equations) under conditional shift based on the deep operator network (DeepONet). Task-specific operator learning is accomplished by fine-tuning task-specific layers of the target DeepONet using a hybrid loss function that allows for the matching of individual target samples while also preserving the global properties of the conditional distribution of the target data. Inspired by conditional embedding operator theory, we minimize the statistical distance between labelled target data and the surrogate prediction on unlabelled target data by embedding conditional distributions onto a reproducing kernel Hilbert space. We demonstrate the advantages of our approach for various transfer learning scenarios involving nonlinear partial differential equations under diverse conditions due to shifts in the geometric domain and model dynamics. Our transfer learning framework enables fast and efficient learning of heterogeneous tasks despite considerable differences between the source and target domains.

42 ENGINEERING↗