SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Static stability and control characteristics of delta wing space shuttle orbiter model 134D at Mach 0.6 to 5
Heat transfer tests for two delta wing configurations were conducted in the hypervelocity wind tunnel. The 24-inch long models were tested at a Mach number of approximately 10.5 and at angles of attack of 20, 40, and 60 degrees over a length Reynolds number range from 5 million to 23 million on 4 May to 4 June 1971. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint.
An investigation was conducted in the Langley 1/8-scale V/STOL model tunnel on a semispan delta wing with a leading-edge sweep of 74 deg, to determine the effectiveness of various locations of upper surface and reflection plane blowing on leading-edge vortex bursting. Constant area nozzles were located on the wing upper surface along a ray swept 79 deg, which was beneath the leading-edge vortex core. The bursting and reformation of the leading-edge vortex was viewed by injecting helium into the vortex core, and employing a schlieren system.
The behavior of vortex-flow, accompanied with breakdown, formed above sharp-edged delta wings, was studied experimentally as well as theoretically. Emphasis is placed particularly on the criterion for the breakdown at sufficiently large Reynolds numbers
Static and unsteady pressures were measured on a 50.45 degree clipped delta wing in the Langley Transonic Dynamics Tunnel with Freon as the test medium. Data taken at M = 0.9 is presented for static and oscillatory deflections of the trailing edge control surface and for the wing in pitch. Comparisons of the static measured data are made with results computed using the Bailey-Ballhaus small disturbance code.
Studies on the solution of discrete Euler equations past swept delta wing configurations with sharp leding edges are presented. Freestream Mach numbers range from zero to supersonic, although the Mach number normal to the leading edge is subsonic for all cases discussed. A few examples are given to show the application of the numerical methods to representative problems. The major dicussion is directed at the application of Computational Fluid Dynamics to the understanding of the fundamental fluid mechanic mechanisms of this class of flows.
The aerodynamic characteristics of a highly swept planar delta wing employing conical leading edge flaps are numerically investigated, using a free vortex sheet method that is based on an advanced, three-dimensional inviscid flow panel method employing quadratic doublet distributions to represent the wing surface and the rolled-up vortex sheet and wake. Upward flap deflection shifts the negative pressure peak inboard of the basic wing and develops a significant suction pressure on the flap that then produces thrust component in the direction of flight; overall drag is thereby reduced.
A numerical simulation of tangential blowing along the leading edge of a delta wing is analyzed as a means of controlling the position and strength of the leading-edge vortices. The computation is done by numerical solutions of the three-dimensional thin-layer Navier-Stokes equations. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of tangential leading-edge blowing at low to moderate angles of attack tends to reduce the pressure peaks associated with leading-edge vortices and to increase the suction peak around the leading edge, such that the integrated value of the surface pressure remains about the same.
Unsteady, transonic vortex-breakdown flow over a 65 deg. sharp edged, cropped-delta wing of zero thickness undergoing forced coupled pitching and rolling oscillations is investigated computationally. The initial condition of the flow is characterized by a transverse terminating shock which induces of the leading edge vortex cores to breakdown. The computational investigation uses the time-accurate solution of the laminar, unsteady, compressible, full Navier-Stokes equations with the implicit, upwind, Roe flux-difference splitting, finite-volume scheme. The main focus is to analyze the effects of coupled motion on the wing response and vortex-breakdown flow by varying oscillation frequency and phase angle while keeping the maximum pitch and roll amplitude equal.
Pressure distributions on flat plate delta wing swept 65 deg at hypersonic speeds at angles of attack from 65 deg to 115 deg and angles of roll from 0 deg to 25 deg at 90 deg angle of attack
An investigation of the aerodynamic performance of leading-edge flaps on three clipped delta and three clipped double-delta wing planforms with aspect ratios of 1.75, 2.11, and 2.50 was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.90, and 2.16. A primary set of fullspan leading-edge flaps with similar root and tip chords were investigated on each wing, and several alternate flap planforms were investigated on the aspect-ratio-1.75 wings. All leading-edge flap geometries were effective in reducing the drag at lifting conditions over the range of wing aspect ratios and Mach numbers tested. Application of a primary flap resulted in better flap performance with the double-delta planform than with the delta planform. The primary flap geometry generally yielded better performance than the alternate flap geometries tested. Trim drag due to flap-induced pitching moments was found to reduce the leading-edge flap performance more for the delta planform than for the double-delta planform. Flow-visualization techniques showed that leading-edge flap deflection reduces crossflow shock-induced separation effects. Finally, it was found that modified linear theory consistently predicts only the effects of leading-edge flap deflection as related to pitching moment and lift trends.
Calculated and experimental hinge moments on trailing-edge flaps of swept delta wings at hypersonic speeds and positive deflection angles
Analytical method for predicting lift and drag for slender sharp-edge delta wings near ground level
Design charts of static and rotary stability derivatives for cropped double delta wings in subsonic compressible flow
Low speed wind tunnel tests on longitudinal and lateral stability of high cross range delta wing space shuttles
Numerous wind tunnel tests conducted on the evolving delta-wing orbiters have generated a fairly large aerodynamic data base over the entire entry operation range of these vehicles. A limited assessment is made of some of the aerodynamics of the current HO type orbiters, and several specific problem areas selected from the broad data base are discussed. These include, from a subsonic viewpoint, discussions of trim drag effect; effects of the installation of main rocket engine nozzles, OMS and RCS packages, Reynolds number effects, lateral-directional stability characteristics, and landing characteristics.
To examine the effect on flutter of the aerodynamic interference between pairs of closely spaced delta wings, several structurally uncoupled 1/80th-scale models were studied by experiment and analysis. Flutter test boundaries run in a 26-in transonic blowdown wind tunnel were compared with subsonic analytical results generated using the doublet lattice method. Trends for several combinations of vertical and longitudinal wing separation showed that flutter speeds can be significantly lowered in closely spaced configurations. For some configurations, a new flutter mechanism, characterized by coupling of the flexible modes from both surfaces at a distinctive flutter frequency, was predicted and observed.
To examine the effect on flutter of the aerodynamic interference between pairs of closely spaced delta wings, several structurally uncoupled 1/80th-scale models were studied by experiment and analysis. Flutter test boundaries obtained in NASA Langley's 26-in. transonic blowdown wind tunnel were compared with subsonic analytical results generated using the doublet lattice method. Trends for several combinations of vertical and longitudinal wing separation were determined, showing flutter speed significantly affected in the closely spaced configurations. A new flutter mechanism coupling one wing's first bending mode with the other wing's first torsion mode was predicted and observed.