Search NASA⌕ Search

SEARCH · Search NASA

Results for “discharges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Modeling Structured Electrodes and Graded Porosity for Improving Discharge Rate Capability in Ultra-Thick Graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 Batteries

Long-range electric vehicles (EVs) require high-energy-density batteries that also meet the power demands of high current charge and discharge. Ultra-thick (>100 μm) Lithium-ion battery electrodes are critical to enable this need, but slow ion transport in conventional uniform electrodes (UEs) reduces battery capacity at increasing charge/discharge rates. We present a 3D computational analysis on the impact of structured electrode (SE) and graded electrode (GE) geometries on the discharge rate capability of ultra-thick graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) battery cells based on the footprint of a commercial EV pouch cell. SE cathodes with either a “grid” or “line” geometry and GEs with two layers of porosity were modeled. Based on the results of 230 models, we found that the electrolyte volume fraction is a key parameter that impacts capacity improvements in UEs, GEs, and SEs at 2 C–6 C discharge rates. SEs have the greatest discharge rate capability, outperforming GEs and UEs due to reduced Lithium-ion concentration gradients across the electrode thickness, which mitigates electrolyte depletion at high rates. The best SE model has a “grid” geometry with gravimetric and volumetric energy density improvements of 0.9%–4% at C/2–2 C and 18%–24% at 4 C–6 C relative to UEs.

25 ENERGY STORAGE↗
DOE OSTI2020

Estimating Watershed Subsurface Permeability From Stream Discharge Data using Deep Neural Networks, Frontiers in Earth Science: Dataset

This data package contains watershed modeling inputs and outputs as well as deep neural networks training and testing results used in "Estimating Watershed Subsurface Permeability From Stream Discharge Data using Deep Neural Networks" (Cromwell et al., 2021). We train various deep neural network models with different architectures to predict subsurface permeability from stream discharge hydrograph at the watershed outlet. The training data are obtained from ensemble simulations of hydrographs corresponding to an permeability ensemble using a fully-distributed, integrated surface-subsurface hydrologic model. The trained model is then applied to estimate the permeability of the real watershed using its observed hydrograph at the outlet. Our study demonstrates that the permeabilities of the soil and geologic facies that make significant contributions to the outlet discharge can be more accurately estimated from the discharge data. Their estimations are also more robust with observation errors. Compared to the traditional ensemble smoother method, DNNs show stronger performance in capturing the nonlinear relationship between permeability and stream hydrograph to accurately estimate permeability. Our study sheds new light on the value of the emerging deep learning methods in assisting integrated watershed modeling by improving parameter estimation, which will eventually reduce the uncertainty in predictive watershed models. For detailed information regarding watershed model description and DNNs setup, please refer to Cromwell et al., 2021. The deep_learning.zip file contains the inputs and outputs for the different deep neural networks. The watershed_model.zip file contains the inputs and outputs for watershed simulation using ATS. The figures.zip file contains raw figures and their corresponding scripts. For a more detailed description, please see the README.md file within each compressed file.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Stream discharge and temperature data collected within the East and Taylor Watershed, Colorado for the Lawrence Berkeley National Laboratory Watershed Function Science Focus Area (water years 2019 to 2025)

This dataset contains stream discharge and temperature data for water years 2019 to 2025 from the East and Taylor Watersheds in Colorado, United States. This data was collected to understand hydrological processes occurring in the East River and Taylor River Watersheds, Colorado, which is part of the Lawrence Berkeley National Laboratory Watershed Function Scientific Focus Area. Data includes instantaneous observed discharge using salt dilution and acoustic doppler velocimeter techniques, raw pressure transducer downloaded data, sub-hourly temperature as well as corrected water level and associated stream discharge and mean daily values. Notes on water level corrections, rating curve development and metadata provided. A rating curve is the translation of depth to streamflow. The rating curve can be used as a quantitative measure of the “quality of the data.” Data within this dataset is formatted using ESS-DIVE’s Hydrological Monitoring Reporting Format. This data package contains (1) a zip file (Stream_Discharge_Data_WY19-WY25.zip) containing stream discharge and temperature data organized by location; (2) an InstallationMethods file (InstallationMethods.csv) describing metadata about the installation; (3) a file-level metadata (flmd.csv) file that lists each file contained in the dataset with associated metadata; (4) a data dictionary (dd.csv) file that contains terms/column_headers used throughout the files along with a definition, units, and data type; (5) a locations metadata file (locations.csv); (6) and a sensor metadata file (sensors.csv). All data files are in non-proprietary formats (csv, png, or pdf formats). Please contact Rosemary Carroll, Curtis Beutler, or Austin Shirley for any support in accessing the files. Update on 2023-05-12: Additional data from WYs 2021 and 2022 were added. Additionally, the dataset was converted using ESS-DIVE’s Hydrological Monitoring Reporting Format. Data files were reformatted to match reporting format guidance, new metadata files were added, and files were converted from excel to CSV. Update on 2025-05-16: Additional data from WYs 2022 (for locations not previously included), 2023, and 2024 were added. An additional descriptive PDF (WFSFA_Streamflow_Hydrograph_Disclaimer.pdf) was added. Metadata files were updated to reflect the addition of new data and locations. Update on 2026-05-18: Additional data from WY 2025 were added, including a new location Upper Trail Creek (TR-TCG2). Metadata files were updated to reflect the addition of new data.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Effects of additively manufactured surface roughness on small diameter plenums with multiple side discharges for high temperature gas turbine blade cooling applications

Combined heat and power (CHP) applications have significant environmental and economic benefits that are consistent with the goals of the U.S. Department of Energy (DOE). One area that is currently being studied includes the potential benefits of CHP turbine operation at higher turbine inlet temperatures. Internal cooling concepts enabled by additive manufacturing (AM) are of primary interest. Here, the effectiveness of internal cooling is hindered by many factors such as velocity distribution of the cooling air to the hot surface considering impingement cooling. To simulate cooling air exiting from a series of orifices for internal cooling in an airfoil, a straight smooth wall tubing with multiple side discharging orifices is used and compared to additively manufactured tubing (Ti6Al4V Grade 23) with orifice size and spacing as well as inner and outer diameters identical to the smooth wall tubing. Similar to flow discharging form perforated pipes, the flow discharged from individual orifices along the tubes in this study is found to be nonuniformly distributed, and the horizontal (axial direction) momentum can be observed from the experimental data. Discharge velocities have been measured with two-dimensional (2D) particle imaging velocimetry (PIV) and single element hot wire anemometry. Numerical analysis has also been conducted to predict the velocity distributions along the orifices in the smooth wall and additive manufacturing (AM) tubing, which are inherited with surface roughness. Numerical and measured results in this study are compared, presented, and discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Evaluation of Ammonia Discharge into PUREX Crib 216-A-37-1 and Nitrogen Species Fate in the Subsurface

Based on published data, this report identifies potential fate and transport mechanisms for the ammonium hydroxide condensate that was discharged to 216-A-37-1 Crib from Hanford fuel rod decladding before PUREX dissolution and separation operations. Crib 216-A-37-1 received 377 million liters of alkaline condensate discharged from March 1977 through April 1989. The following major processes were identified as controlling the ammonia (NH 3 ) fate and transport: 1. Liquid migration rates through the vadose zone 2. NH 3 microbial oxidation to nitrite and nitrate 3. Ammonia species [NH4 + , NH 3 (aq)] sorption to sediments 4. NH3 precipitation reactions after pH buffering occurs in sediments The travel time through the vadose zone was estimated to be 2.5 to 9 months during periods of high subsurface discharge rates. These travel times are based on tritium migration through the vadose zone, a co-contaminant also discharged to the 216-A-37-1 crib.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

A semi-supervised machine learning detector for physics events in tokamak discharges

Databases of physics events have been used in various fusion research applications, including the development of scaling laws and disruption avoidance algorithms, yet they can be time-consuming and tedious to construct. This paper presents a novel application of the label spreading semi-supervised learning algorithm to accelerate this process by detecting distinct events in a large dataset of discharges, given few manually labeled examples. A high detection accuracy (>85%) for H-L back transitions and initially rotating locked modes is demonstrated on a dataset of hundreds of discharges from DIII-D with manually identified events for which only 3 discharges are initially labeled by the user. Lower yet reasonable performance (~75%) is also demonstrated for the core radiative collapse, an event with a much lower prevalence in the dataset. Additionally, analysis of the performance sensitivity indicates that the same set of algorithmic parameters is optimal for each event. This suggests that the method can be applied to detect a variety of other events not included in this paper, given that the event is well described by a set of 0D signals robustly available on many discharges. Procedures for analysis of new events are demonstrated, showing automatic event detection with increasing fidelity as the user strategically adds manually labeled examples. Detections on Alcator C-Mod and EAST are also shown, demonstrating the potential for this to be used on a multi-tokamak dataset.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1971

An experimental investigation of a hollow cathode discharge

An experimental study of the effects of various modifications to the hollow cathode discharge region of a 20 cm electron bombardment ion thruster is presented. The introduction of electrical insulation between the main and cathode discharge regions is shown to have no significant effect on thruster performance. Adjustment of both the diameter and length of the cathode discharge region from the design condition are examined and the reduced sizes are shown to effect large improvements in propellant utilization when the thruster is operating at about 30% of the design thrust level. Performance improvements are shown to be less significant at higher thrust levels. The feasibility of using a high voltage tickler electrode to initiate the cathode-keeper discharge is considered and results obtained suggest this mode of startup is unsatisfactory.

Wilbur, P. J.↗
NASA NTRS1972

Propellant sidefeed-short pulse discharge thruster studies

The technique of feeding a solid propellant into the discharge from the sides of the discharge was evaluated. The thrust/power ratio could be significantly effected by the included angle of V-shaped propellants and by the electrode length. This result implies that when results are compared at the same specific impulse it is possible to obtain higher thrust efficiencies. In particular, it was found that for a given discharge energy the thrust/power ratio correlated with propellant mass. Increasing the integral simultaneously increases both the gas dynamic and electromagnetic thrust. An analytic expression was formulated for ablated mass which comprehensively describes experimental data in terms of geometry and electrical parameters. The correlation of the product impulse x specific impulse with discharge energy was also described. It is suggested that the reliability of dry energy storage capacitors does not equal the reliability of liquid impregnated units when the comparison is made at the same joules/Kg rating.

Palumbo, D. J.↗
NASA NTRS1973

Parametric investigation of enclosed keeper discharge characteristics

Volt-ampere discharge characteristics of an enclosed keeper hollow cathode discharge were measured as a function of the mercury flow rate and external circuit impedance. Discharge currents were varied from 0 to 1 ampere and voltages were 7 to 39 volts. Batteries and a vacuum tube control circuit were used to obtain characteristics curves that were independent of power supply impedance. Variation of the neutral flow results in changes in the discharge which interact with the impedance of the external circuit, and under some conditions, give rise to multiple operating points.

Sheheen, T. W.↗
NASA NTRS1973

Increase in transmittance of unbacked aluminum filters exposed to RF or dc discharges in oxygen

Results of an experimental study of the effect of discharges in oxygen on the oxide thickness and transmittance of aluminum filters. The studies were performed by exposing the filters to RF discharges and dc glow discharges in oxygen. In all experiments except one in which an aluminum ring was used as the cathode an increase in the transmittance of the filters is noted. It is thus demonstrated that the transmittance of aluminum filters increases on exposure to electrical discharges in oxygen, although it is not certain whether this phenomenon is caused by atomic oxygen.

Hunter, W. R.↗
NASA NTRS1974

Acceleration processes in the quasi-steady magnetoplasmadynamic discharge

The flow field characteristics within the discharge chamber and exhaust of a quasi-steady magnetoplasmadynamic (MPD) arcjet were examined to clarify the nature of the plasma acceleration process. The observation of discharge characteristics unperturbed by insulator ablation and terminal voltage fluctuations, first requires the satisfaction of three criteria: the use of refractory insulator materials; a mass injection geometry tailored to provide propellant to both electrode regions of the discharge; and a cathode of sufficient surface area to permit nominal MPD arcjet operation for given combinations of arc current and total mass flow. The axial velocity profile and electromagnetic discharge structure were measured for an arcjet configuration which functions nominally at 15.3 kA and 6 g/sec argon mass flow. An empirical two-flow plasma acceleration model is advanced which delineates inner and outer flow regions and accounts for the observed velocity profile and calculated thrust of the accelerator.

Boyle, M. J.↗
NASA NTRS1975

Determination of electron temperature in a penning discharge by the helium line ratio method

The helium line ratio technique was used to determine electron temperatures in a toroidal steady-state Penning discharge operating in helium. Due to the low background pressure, less than .0001 torr, and the low electron density, the corona model is expected to provide a good description of the excitation processes in this discharge. In addition, by varying the Penning discharge anode voltage and background pressure, it is possible to vary the electron temperature as measured by the line ratio technique over a wide range (10 to 100+ eV). These discharge characteristics allow a detailed comparison of electron temperatures measured from different possible line ratios over a wide range of temperatures and under reproducible steady-state conditions. Good agreement is found between temperatures determined from different neutral line ratios, but use of the helium ion line results in a temperature systematically 10 eV high compared to that from the neutral lines.

Richardson, R. W.↗
NASA NTRS1974

The synthesis of higher oxides of alkali and alkaline earth metals in an electric discharge: Theoretical and experimental studies

Potassium hydroxide was subjected to the products of an electrical discharge sustained in oxygen and produced both potassium peroxide and superoxide. The conversion to higher oxides was shown to strongly depend upon the particle size of KOH, the position of KOH in the discharge zone, and the operating conditions of the discharge. Similar experiments were performed with hydroxides of lithium and calcium which do not form superoxides, but are converted to peroxides. The yields of peroxides were shown to strongly depend upon the operating conditions of the discharge. The absence of superoxides and the presence of peroxides of lithium and calcium was explained from the consideration of relative thermodynamic stability of the oxides of lithium and calcium. Thermogravimetric analysis was shown to provide a more accurate means for determining the amount of KO2 than previous methods.

Bell, A. T.↗
NASA NTRS1975

Transient currents generated by electrical discharges

Analytical expressions for the electromagnetic coupling between electrical discharges and floating conducting surfaces are derived. Electrical discharges can occur on satellite surfaces during energetic electron injection events associated with magnetospheric substorms. The theory presented here can be used to study interference to electronic circuits that may be caused by such discharges. The expressions derived in this paper are consistent with laboratory calibrations of an electrical pulse counter that has detected such discharges on a geostationary satellite.

Cauffman, D. P.↗
NASA NTRS1976

Potential efficiencies of open- and closed-cycle CO, supersonic, electric-discharge lasers

Computed open- and closed-cycle system efficiencies (laser power output divided by electrical power input) are presented for a CW carbon monoxide, supersonic, electric-discharge laser. Closed-system results include the compressor power required to overcome stagnation pressure losses due to supersonic heat addition and a supersonic diffuser. The paper shows the effect on the system efficiencies of varying several important parameters. These parameters include: gas mixture, gas temperature, gas total temperature, gas density, total discharge energy loading, discharge efficiency, saturated gain coefficient, optical cavity size and location with respect to the discharge, and supersonic diffuser efficiency. Maximum open-cycle efficiency of 80-90% is predicted; the best closed-cycle result is 60-70%.

Monson, D. J.↗
NASA NTRS1977

Plasma rotation by electric and magnetic fields in a discharge cylinder

A theoretical model for an electric discharge consisting of a spatially diverging plasma sustained electrically between a small ring cathode and a larger ring anode in a cylindrical chamber with an axial magnetic field is developed to study the rotation of the discharge plasma in the crossed electric and magnetic fields. The associated boundary-value problem for the coupled partial differential equations which describe the electric potential and the plasma velocity fields is solved in closed form. The electric field, current density, and velocity distributions are discussed in terms of the Hartmann number and the Hall coefficient. As a result of Lorentz forces, the plasma rotates with speeds as high as 1 million cm/sec around its axis of symmetry at typical conditions. As an application, it is noted that rotating discharges of this type could be used to develop a high-density plasma-ultracentrifuge driven by j x B forces, in which the lighter (heavier) ion and atom components would be enriched in (off) the center of the discharge cylinder.

Wilhelm, H. E.↗
NASA NTRS1976

Arc discharge supply component protection circuitry

In a mercury-bombardment ion engine, the discharge supply is a high-current low-voltage one that maintains an arc or discharge inside the engine. In a 30-cm engine the supply provides up to 45 volts at about 13 amperes and is referenced at approximately 1100 volts above ground. Due to the engine discharge characteristics, a very slow feedback control loop is required. A high-speed current limit must be used to protect the components in the power conditioner, a pulse-width-modulated bridge inverter. A high-speed cycle-by-cycle current-limit circuit which allows the inverter to continue running in an overcurrent condition is used to protect it. The high-speed current sensing allows the inverter to be turned off each half cycle before the current in the primary of the inverter exceeds a safe level. This permits the inverter to continue to provide current into a discharge or a fault condition, until the feedback control system can actively control the current.

Ahrens, A. F.↗
NASA NTRS1977

Small-signal gain diagnostic measurements in a flowing CO2 pin discharge laser

Small-signal gain diagnostic measurements were conducted on closed loop, high power, carbon dioxide laser to assess the coupling between gas flow velocity and resonator saturation. Parameters investigated included optical cavity and discharge power. Results of gain measurements within and downstream of the excitation volume are presented for a laser gas composition He:N2:CO2 of 10:7:1 at 90 torr. The gain at constant discharge power was observed to be dependent upon discharge power level and time. An important result of this study is that the effects of gain swept downstream of the discharge region must be considered in the resonator design if efficient extraction of stored optical energy is desired.

Blech, R. A.↗