SEARCH · Search NASA

Results for “effective transference number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Recent thermal models of the chromosphere

The paper describes recent research on the calculation of solar chromospheric models. The models included here are based on the observed spectrum, and on the assumption of hydrostatic equilibrium. The calculations depend on realistic solutions of the radiative transfer and statistical equilibrium equations for optically thick lines and continua, and on including the effects of large numbers of lines throughout the spectrum. Although spectroheliograms show that the structure of the chromosphere is highly complex, one-dimensional models of particular features are reasonably successful in matching observed spectra. There has been considerable recent progress in applying such models to the interpretation of chromospheric observations.

Avrett, E. H.↗

NASA NTRS2001

High Pressure, Transport Properties of Fluids: Theory and Data from Levitated Fluid-Drops at Combustion-Relevant Temperatures

The objective of this investigation is to derive a set of consistent mixing rules for calculating diffusivities and thermal diffusion factors over a thermodynamic regime encompassing the subcritical and supercritical ranges. These should serve for modeling purposes, and therefore for accurate simulations of high pressure phenomena such as fluid disintegration, turbulent flows and sprays. A particular consequence of this work will be the determination of effective Lewis numbers for supercritical conditions, thus enabling the examination of the relative importance of heat and mass transfer at supercritical pressures.

Bellan, J.↗

NASA NTRS2002

Effect of Favorable Pressure Gradients on Turbine Blade Pressure Surface Heat Transfer

Recent measurements on a turbine rotor showed significant relaminarization effects. These effects were evident on the pressure surface heat transfer measurements. The character of the heat transfer varied with Reynolds number. Data were obtained for exit Reynolds numbers between 500,000 and 880,000. Tests were done with a high level of inlet turbulence, 7.5%. At lower Reynolds numbers the heat transfer was similar to that for laminar flow, but at a level higher than for laminar flow. At higher Reynolds numbers the heat transfer was similar to turbulent flow, when the acceleration parameter, K, was sufficiently small. The proposed paper discusses the experimental results, and also discusses approaches to calculating the surface heat transfer for the blade surface. Calculations were done using a three-dimensional Navier-Stokes CFD analysis. The results of these tests, when compared with previous blade tests in the same facility, illustrate modeling difficulties that were encountered in CFD predictions. The two blades were in many ways similar. However, the degree of agreement between the same analysis and the experimental data was significantly different. These differences are highlighted to illustrate where improvements in modeling approaches are needed for transitional flows.

Boyle, Robert J.↗

NASA NTRS1990

Heat transfer in rotating serpentine passages with smooth walls

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi-pass, smooth-wall heat transfer model with both radially inward and outward flow. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages (coolant-to-wall temperature ratio, Rossby number, Reynolds number and radius-to-passage hydraulic diameter ratio). These four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. It was found that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs and that the effect of rotation on the heat transfer coefficients was markedly different depending on the flow direction. Local heat transfer coefficients were found to decrease by as much as 60 percent and increase by 250 percent from no rotation levels. Comparisons with a pioneering stationary vertical tube buoyancy experiment showed reasonably good agreement. Correlation of the data is achieved employing dimensionless parameters derived from the governing flow equations.

Wagner, J. H.↗

NASA NTRS1998

Effects of Ice Accretion on Aircraft Aerodynamics

The primary objective of this research was to support the development of a new ice accretion model by improving our physical understanding of the ice accretion process through experimental measurements. The focus was on the effect of the initial ice roughness (smooth/rough boundary) on the accretion process. This includes understanding the boundary-layer development over the roughness and especially its effect on the heat transfer which is fundamental to the ice accretion process. The research focused on acquiring the experimental data needed to formulate a new ice accretion physical model. Research was conducted to analyze boundary-layer data taken on a NACA 0012 airfoil with roughness to simulate the smooth/rough boundary. The effect of isolated roughness on boundary-layer transition was studied experimentally to determine if the classical critical roughness Reynolds number criteria could be applied to transition in the airfoil leading-edge area. The effect of simulated smooth/rough boundary roughness on convective heat transfer was studied to complete the study. During the course of this research the effect of free-stream wind tunnel turbulence on the boundary layer was measured. Since this quantity was not well known, research to accurately measure the wind tunnel turbulence in an icing cloud was undertaken. Preliminary results were attained and the final data were acquired, reduced and presented under a subsequent grant.

Bragg, Michael B.↗

NASA NTRS1992

Flow effects in a vertical CVD reactor

A model is presented to simulate the non-Boussinesq flow in a vertical, two-dimensional, chemical vapor deposition reactor under atmospheric pressure. Temperature-dependent conductivity, mass diffusivity, viscosity models, and reactive species mass transfer to the substrate are incorporated. In the limits of small Mach number and small aspect ratio, asymptotic expressions for the flow, temperature, and species fields are developed. Soret diffusion effects are also investigated. Analytical solutions predict an inverse relationship between temperature field and concentration field due to Soret effects. This finding is consistent with numerical simulations, assisting in the understanding of the complex interactions amongst the flow, thermal, and species fields in a chemically reacting system.

Young, G. W.↗

NASA NTRS1951

Laminar friction and heat transfer at Mach numbers from 1 to 10

Velocity and temperature profiles and laminar boundary-layer characteristics have been computed for Mach numbers from 1 to 10, utilizing experimental values of the heat capacity, viscosity, and conductivity. The analysis shows that effective temperature, which is a function of the surface temperature and stream conditions, arises naturally and is the proper reference temperature to be used in heat-transfer calculations. The effective temperature and the recovery temperature become identical for the condition of zero heat transfer.

Klunker, E B↗

DOE OSTI2024

A reactive electrochemomechanical theory for growth and remodeling of polyelectrolyte hydrogels and application to dynamic polymerization of $\text{DNA}$ hydrogels

Here this study develops a framework for growth and remodeling of active polyelectrolyte hydrogels that accounts for effects of compositional changes on the mechanical response. By developing a reactive electrochemomechanical theory, thermodynamical constraints upon reactive and remodeling processes are elucidated within a general framework that allows any number of chemical reactions to evolve the response of the gel and transfer mass and charge between constituents. Fully coupled, nonlinear constitutive relations are adopted for molar fluxes, allowing exploration of effects including cross-diffusion, electrophoresis, and electro-osmosis. A robust finite element implementation is developed in the open source FEBio software (febio.org) by exploiting an equivalence between electrochemomechanics and mixture theory. The implementation is verified against analytical solutions for free swelling, and a proper reduction to a prior chemomechanical theory is demonstrated for neutral gels swollen only by a solvent with no solutes. The theory and implementation are then applied to model the tunable large swelling achieved through dynamic polymerization of DNA crosslinkers seen in our recently developed experimental hydrogel system (Cangialosi et al., 2017). A novel constitutive model for reaction-driven evolution of the locking stretch λ L in a non-Gaussian mechanical free energy was developed, where the increasing concentration of DNA crosslinkers makes further swelling energetically favorable. With a single free parameter, excellent agreement was found between measured and predicted equilibrium swelling ratios. This study demonstrated the ability to extend the electrochemomechanical framework to include chemical reactions and composition-aware constitutive models, and showed that development of reactive models allows simulation of complex dynamic polymerization phenomena not treated before. The theoretical frame here can be further expanded in scope to incorporate additional non-ideal and nonlinear phenomena.

42 ENGINEERING↗

NASA NTRS1978

Pressure and heat-transfer distributions in a simulated wing-elevon cove with variable leakage at a free-stream Mach number of 6.9

An experimental aerodynamic heating investigation was conducted to determine effects of hot boundary-layer ingestion into the cove on the windward surface between a wing and elevon for cove seal leak areas nominally between 0 and 100 percent of cove entrance area. Pressure and heating-rate distributions were obtained on the wing and elevon surfaces and on the cove walls of a full-scale model that represented a section of the cove region on the space shuttle orbiter. Data were obtained for both attached and separated turbulent boundary layers upstream of the unswept cove entrance. Average free-stream Mach number was 6.9, average free-stream unit Reynolds numbers were 1.31 x 10 to the 6th power and 4.40 x 10 to the 6th power per meter (0.40 x 10 to the 6th power and 1.34 x 10 to the 6th power per foot), and average total temperature was 1888 K (3400 R). Cove pressures and heating rates varied as a function of seal leak area independent of leak aspect ratio. Although cove heating rates for attached flow did not appear intolerable, it was postulated that convective heating in the cove may increase with time. For separated flow, the cove environment was considered too severe for unprotected interior structures of control surfaces.

Deveikis, W. D.↗

NASA NTRS1990

Numerical investigation of the thermal stratification in cryogenic tanks subjected to wall heat flux

The flow pattern and thermal stratification of a cryogenic cylindrical tank are numerically studied. The tank sidewall is subjected to either a uniform heat-flux or two discrete levels of uniform heat-flux at the upper and lower halves of the tank wall. The tank bottom is kept at a constant temperature controlled by the heat exchanger of a thermodynamic vent system. The tank pressure is also assumed constant resulting in a constant saturation temperature at the interface which is higher than the tank bottom temperature. The effects of vapor motion and vapor superheat on the mass and heat transfer processes at the interface are assumed negligible such that the calculations of liquid region can be decoupled from the vapor region. Dimensionless steady-state conservation equations are solved by a finite-difference method. The effects of modified Rayleigh number, Prandtl number, tank aspect ratio, wall heat-flux parameter, and wall heat-flux distribution on the liquid velocity and temperature fields are investigated. Also, their effects on the rate of heat transfer through the interface and the tank bottom are examined.

Lin, Chin-Shun↗

NASA NTRS1990

Numerical investigation of the thermal stratification in cryogenic tanks subjected to wall heat flux

Lin, Chin-Shun↗

NASA NTRS1987

Use of a liquid-crystal, heater-element composite for quantitative, high-resolution heat transfer coefficients on a turbine airfoil, including turbulence and surface roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at roon temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, Steven A.↗

NASA NTRS1987

Use of a liquid-crystal and heater-element composite for quantitative, high-resolution heat-transfer coefficients on a turbine airfoil including turbulence and surface-roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, S. A.↗

NASA NTRS1999

Formation and Levitation of Unconfined Droplet Clusters

Liu, S.↗

NASA NTRS2001

Combustion of Unconfined Droplet Clusters in Microgravity

Combustion experiments using arrays of droplets seek to provide a link between single droplet combustion phenomena and the behavior of complex spray combustion systems. Both single droplet and droplet array studies have been conducted in microgravity to better isolate the droplet interaction phenomena and eliminate or reduce the confounding effects of buoyancy-induced convection. In most experiments involving droplet arrays, the droplets are supported on fibers to keep them stationary and close together before the combustion event. The presence of the fiber, however, disturbs the combustion process by introducing a source of heat transfer and asymmetry into the configuration. As the number of drops in a droplet array increases, supporting the drops on fibers becomes less practical because of the cumulative effect of the fibers on the combustion process. To eliminate the effect of the fiber, several researchers have conducted microgravity experiments using unsupported droplets. Jackson and Avedisian investigated single, unsupported drops while Nomura et al. studied droplet clouds formed by a condensation technique. The overall objective of this research is to extend the study of unsupported drops by investigating the combustion of well-characterized drop clusters in a microgravity environment. Direct experimental observations and measurements of the combustion of droplet clusters would fill a large gap in our current understanding of droplet and spray combustion and provide unique experimental data for the verification and improvement of spray combustion models. In this work, the formation of drop clusters is precisely controlled using an acoustic levitation system so that dilute, as well as dense clusters can be created and stabilized before combustion in microgravity is begun. This paper describes the design and performance of the 1-g experimental apparatus, some preliminary 1-g results, and plans for testing in microgravity.

Ruff, G. A.↗

NASA NTRS2003

Droplet Vaporization In A Levitating Acoustic Field

Combustion experiments using arrays of droplets seek to provide a link between single droplet combustion phenomena and the behavior of complex spray combustion systems. Both single droplet and droplet array studies have been conducted in microgravity to better isolate the droplet interaction phenomena and eliminate or reduce the effects of buoyancy-induced convection. In most experiments involving droplet arrays, the droplets are supported on fibers to keep them stationary and close together before the combustion event. The presence of the fiber, however, disturbs the combustion process by introducing a source of heat transfer and asymmetry into the configuration. As the number of drops in a droplet array increases, supporting the drops on fibers becomes less practical because of the cumulative effect of the fibers on the combustion process. To eliminate the effect of the fiber, several researchers have conducted microgravity experiments using unsupported droplets. Jackson and Avedisian investigated single, unsupported drops while Nomura et al. studied droplet clouds formed by a condensation technique. The overall objective of this research is to extend the study of unsupported drops by investigating the combustion of well-characterized drop clusters in a microgravity environment. Direct experimental observations and measurements of the combustion of droplet clusters would provide unique experimental data for the verification and improvement of spray combustion models. In this work, the formation of drop clusters is precisely controlled using an acoustic levitation system so that dilute, as well as dense clusters can be created and stabilized before combustion in microgravity is begun. While the low-gravity test facility is being completed, tests have been conducted in 1-g to characterize the effect of the acoustic field on the vaporization of single and multiple droplets. This is important because in the combustion experiment, the droplets will be formed and levitated prior to ignition. Therefore, the droplets will begin to vaporize in the acoustic field thus forming the "initial conditions" for the combustion process. Understanding droplet vaporization in the acoustic field of this levitator is a necessary step that will help to interpret the experimental results obtained in low-gravity.

Ruff, G. A.↗

NASA NTRS1984

The effect of channel convergence on heat transfer in a passage with short pin fins

Array averaged heat transfer coefficients were obtained for two configurations of short pin fins in a converging channel and for two flat plate configurations in a converging channel. The effect of flow acceleration due to channel convergence and the effect of varying pin length on the heat transfer was determined. Results are presented in the form of Nusselt number versus Reynolds number for the four geometries tested.

Brigham, B. A.↗

NASA NTRS1993

Turbulent flow in a channel with transverse rib heat transfer augmentation

Turbulent flow in a 2D channel with repeated rectangular rib roughness was numerically simulated using a low Reynolds number form of the k-epsilon turbulence model. Friction factors and average Stanton numbers were calculated for various pitch to rib height ratios and bulk Reynolds numbers. Comparisons with experiment were generally adequate, with the predictions of friction superior to those for heat transfer. The effect of variable properties for channel flow was investigated, and the results showed a greater effect for friction than for heat transfer. Comparison with experiment yielded no clear conclusions. The turbulence model was also validated for a related problem, that of flow downstream of an abrupt pipe expansion.

Chang, B. H.↗