Search NASA⌕ Search

SEARCH · Search NASA

Results for “engine modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Enhanced Engine Performance During Emergency Operation Using a Model-Based Engine Control Architecture

This paper discusses the design and application of model-based engine control (MBEC) for use during emergency operation of the aircraft. The MBEC methodology is applied to the Commercial Modular Aero-Propulsion System Simulation 40k (CMAPSS40k) and features an optimal tuner Kalman Filter (OTKF) to estimate unmeasured engine parameters, which can then be used for control. During an emergency scenario, normally-conservative engine operating limits may be relaxed to increase the performance of the engine and overall survivability of the aircraft; this comes at the cost of additional risk of an engine failure. The MBEC architecture offers the advantage of estimating key engine parameters that are not directly measureable. Estimating the unknown parameters allows for tighter control over these parameters, and on the level of risk the engine will operate at. This will allow the engine to achieve better performance than possible when operating to more conservative limits on a related, measurable parameter.

engine control↗
NASA NTRSDate not supplied

System Safety Analysis of Complex NASA Systems with Model-Based Engineering (REV B)

The emergence of model-based engineering is transforming design and analysis methodologies. A recognized benefit of model-based engineering is the existence of a “single source of truth” about the system that becomes the authoritative source of data and information for designers, analysts, and developers. This promotes consistency and efficiency as the design emerges and can be used to further optimize the design. Integrating System Safety Engineers to the “single source of truth” will ensure that the outputs of their assessments and analyses are relevant to the design as it evolves. Use of an integrated system model enables near immediate evaluation of a design change as well as development of operational processes for risk assessment and communication. Such models can enable efficient and timely analysis of system hazards (e.g., hazard fault tree analysis and procedure simulations) and produce complete, accurate, and more consistent products (e.g., hazard reports and safety requirement evaluations). Therefore, an agency-sponsored team at Goddard Space Flight Center (GSFC) recently completed a System Safety Study of modeling and testing capabilities as part of a Model-Based Safety and Mission Assurance Initiative (MBSMAI). Using an existing model developed for reliability analyses, GSFC modeling and system safety experts performed system safety analysis/modeling and produced safety products. The team evaluated model-based feasibility to support System Safety Engineering, developed safety analysis modeling processes, and identified tool capability advancement/development needs. These study results indicate model-based engineering is valid and useable for System Safety Engineering for NASA if adequate modeling processes and environment are established.

NASA↗
NASA NTRS2010

NEXT Single String Integration Test Results

As a critical part of NASA's Evolutionary Xenon Thruster (NEXT) test validation process, a single string integration test was performed on the NEXT ion propulsion system. The objectives of this test were to verify that an integrated system of major NEXT ion propulsion system elements meets project requirements, to demonstrate that the integrated system is functional across the entire power processor and xenon propellant management system input ranges, and to demonstrate to potential users that the NEXT propulsion system is ready for transition to flight. Propulsion system elements included in this system integration test were an engineering model ion thruster, an engineering model propellant management system, an engineering model power processor unit, and a digital control interface unit simulator that acted as a test console. Project requirements that were verified during this system integration test included individual element requirements ; integrated system requirements, and fault handling. This paper will present the results of these tests, which include: integrated ion propulsion system demonstrations of performance, functionality and fault handling; a thruster re-performance acceptance test to establish baseline performance: a risk-reduction PMS-thruster integration test: and propellant management system calibration checks.

Soulas, George C.↗
NASA NTRS1979

Initial comparison of single cylinder Stirling engine computer model predictions with test results

A NASA developed digital computer code for a Stirling engine, modelling the performance of a single cylinder rhombic drive ground performance unit (GPU), is presented and its predictions are compared to test results. The GPU engine incorporates eight regenerator/cooler units and the engine working space is modelled by thirteen control volumes. The model calculates indicated power and efficiency for a given engine speed, mean pressure, heater and expansion space metal temperatures and cooler water inlet temperature and flow rate. Comparison of predicted and observed powers implies that the reference pressure drop calculations underestimate actual pressure drop, possibly due to oil contamination in the regenerator/cooler units, methane contamination in the working gas or the underestimation of mechanical loss. For a working gas of hydrogen, the predicted values of brake power are from 0 to 6% higher than experimental values, and brake efficiency is 6 to 16% higher, while for helium the predicted brake power and efficiency are 2 to 15% higher than the experimental.

Tew, R. C., Jr.↗
NASA NTRS2008

Multiplexed Predictive Control of a Large Commercial Turbofan Engine

Model predictive control is a strategy well-suited to handle the highly complex, nonlinear, uncertain, and constrained dynamics involved in aircraft engine control problems. However, it has thus far been infeasible to implement model predictive control in engine control applications, because of the combination of model complexity and the time allotted for the control update calculation. In this paper, a multiplexed implementation is proposed that dramatically reduces the computational burden of the quadratic programming optimization that must be solved online as part of the model-predictive-control algorithm. Actuator updates are calculated sequentially and cyclically in a multiplexed implementation, as opposed to the simultaneous optimization taking place in conventional model predictive control. Theoretical aspects are discussed based on a nominal model, and actual computational savings are demonstrated using a realistic commercial engine model.

Richter, hanz↗
NASA NTRS1986

UH-60 Black Hawk engineering simulation model validation and proposed modifications

The engineering simulation model of the UH-60A Black Hawk was validated using comparisons of model time histories with flight test data and updated to improve the fidelity of the model. The flight test data, acquired by the Army Aviation Engineering Flight Activity and consisting of 90 time histories of transient responses to step and pulse control inputs and 16 sets of steady flight data, were processed and compared to corresponding model time histories and trim data by Sikorsky. The current UH-60A model was judged to provide an acceptably accurate simulation for use as an analytical tool, certain unsatisfactory areas were identified and potential approaches to produce a more representative simulation were evaluated.

Kaplita, Thaddeus T.↗
NASA NTRS2016

Towards a Reference Architecture for Model-Based Engineering Environments

A key aspect of adopting model-based systems engineering as a practice in an organization is the design and development, and adoption of corresponding processes and tools that support the model-based paradigm. In an effort to enable the unified implementation of such processes and tools, this paper introduces a reference architecture model that serves as a specification for a model-based engineering environment. Current systems engineering practices, products, processes and technologies are used as input for continuously refining the architecture model. In the paper, we introduce and report on the current status of this reference architecture model, and present the methodology applied in developing the reference architecture. We conclude that while there are a very large number of domain- or application-specific processes requiring specialized behavior, these can be reduced through abstraction to a small set of core functions that need to be supported by a realization of a model-based engineering environment. Only very few organization-domain- or application-specific aspects require specialized consideration.

Herzig, Sebastian J. I.↗
NASA NTRS1981

Apparatus for sensor failure detection and correction in a gas turbine engine control system

A gas turbine engine control system maintains a selected level of engine performance despite the failure or abnormal operation of one or more engine parameter sensors. The control system employs a continuously updated engine model which simulates engine performance and generates signals representing real time estimates of the engine parameter sensor signals. The estimate signals are transmitted to a control computational unit which utilizes them in lieu of the actual engine parameter sensor signals to control the operation of the engine. The estimate signals are also compared with the corresponding actual engine parameter sensor signals and the resulting difference signals are utilized to update the engine model. If a particular difference signal exceeds specific tolerance limits, the difference signal is inhibited from updating the model and a sensor failure indication is provided to the engine operator.

Spang, H. A., III↗
NASA NTRS2011

Engine Icing Modeling and Simulation (Part 2): Performance Simulation of Engine Rollback Phenomena

Ice buildup in the compressor section of a commercial aircraft gas turbine engine can cause a number of engine failures. One of these failure modes is known as engine rollback: an uncommanded decrease in thrust accompanied by a decrease in fan speed and an increase in turbine temperature. This paper describes the development of a model which simulates the system level impact of engine icing using the Commercial Modular Aero-Propulsion System Simulation 40k (C-MAPSS40k). When an ice blockage is added to C-MAPSS40k, the control system responds in a manner similar to that of an actual engine, and, in cases with severe blockage, an engine rollback is observed. Using this capability to simulate engine rollback, a proof-of-concept detection scheme is developed and tested using only typical engine sensors. This paper concludes that the engine control system s limit protection is the proximate cause of iced engine rollback and that the controller can detect the buildup of ice particles in the compressor section. This work serves as a feasibility study for continued research into the detection and mitigation of engine rollback using the propulsion control system.

May, Ryan D.↗
NASA NTRS1988

An experimental investigation of the effect of test-cell pressure on the performance of resistojets

The effect of test-cell pressure on the performance of two resistojets was investigated. Tests were conducted in a vacuum facility at pressures ranging from 0.000043 to 0.54 torr for two resistojet configurations: a laboratory model and an engineering model for the Space Station. The tests showed that for each thruster there was a decline in performance when tested in vacuum pressures above 0.001 torr. Measurements were made of surface temperature, thrust, and exit-plane pitot pressure over the range of test-cell pressures. From these measurements, the decline in performance of the laboratory-model resistojet at higher cell pressures was attributed to heat losses due to convection. For the engineering-model resistojet, the decline in performance was found to be a combination of heat loss and an effect of cell pressure on the nozzle flow.

Manzella, D. H.↗
NASA NTRS2011

Update - Concept of Operations for Integrated Model-Centric Engineering at JPL

The increasingly ambitious requirements levied on JPL's space science missions, and the development pace of such missions, challenge our current engineering practices. All the engineering disciplines face this growth in complexity to some degree, but the challenges are greatest in systems engineering where numerous competing interests must be reconciled and where complex system level interactions must be identified and managed. Undesired system-level interactions are increasingly a major risk factor that cannot be reliably exposed by testing, and natural-language single-viewpoint specifications areinadequate to capture and expose system level interactions and characteristics. Systems engineering practices must improve to meet these challenges, and the most promising approach today is the movement toward a more integrated and model-centric approach to mission conception, design, implementation and operations. This approach elevates engineering models to a principal role in systems engineering, gradually replacing traditional document centric engineering practices.

The Concept of Operations (ConOps)↗
NASA NTRS1984

NASA Lewis F100 engine testing

Two builds of an F100 engine model derivative (EMD) engine were evaluated for improvements in engine components and digital electronic engine control (DEEC) logic. Two DEEC flight logics were verified throughout the flight envelope in support of flight clearance for the F100 engine model derivative program (EMPD). A nozzle instability and a faster augmentor transient capability was investigated in support of the F-15 DEEC flight program. Off schedule coupled system mode fan flutter, DEEC nose-boom pressure correlation, DEEC station six pressure comparison, and a new fan inlet variable vane (CIVV) schedule are identified.

Werner, R. A.↗
NASA NTRS2002

REACH: Real-Time Data Awareness in Multi-Spacecraft Missions

Missions have been proposed that will use multiple spacecraft to perform scientific or commercial tasks. Indeed, in the commercial world, some spacecraft constellations already exist. Aside from the technical challenges of constructing and flying these missions, there is also the financial challenge presented by the tradition model of the flight operations team (FOT) when it is applied to a constellation mission. Proposed constellation missions range in size from three spacecraft to more than 50. If the current ratio of three-to-five FOT personnel per spacecraft is maintained, the size of the FOT becomes cost prohibitive. The Advanced Architectures and Automation Branch at the Goddard Space Flight Center (GSFC Code 588) saw the potential to reduce the cost of these missions by creating new user interfaces to the ground system health-and-safety data. The goal is to enable a smaller FOT to remain aware and responsive to the increased amount of ground system information in a multi-spacecraft environment. Rather than abandon the tried and true, these interfaces were developed to run alongside existing ground system software to provide additional support to the FOT. These new user interfaces have been combined in a tool called REACH. REACH-the Real-time Evaluation and Analysis of Consolidated Health-is a software product that uses advanced visualization techniques to make spacecraft anomalies easy to spot, no matter how many spacecraft are in the constellation. REACH reads a real-time stream of data from the ground system and displays it to the FOT such that anomalies are easy to pick out and investigate. Data visualization has been used in ground system operations for many years. To provide a unique visualization tool, we developed a unique source of data to visualize: the REACH Health Model Engine. The Health Model Engine is rule-based software that receives real-time telemetry information and outputs "health" information related to the subsystems and spacecraft that the telemetry belong to. The Health Engine can run out-of-the-box or can be tailored with a scripting language. Out of the box, it uses limit violations to determine the health of subsystems and spacecraft; when tailored, it determines health using equations combining the values and limits of any telemetry in the spacecraft. The REACH visualizations then "roll up" the information from the Health Engine into high level, summary displays. These summary visualizations can be "zoomed" into for increasing levels of detail. Currently REACH is installed in the Small Explorer (SMEX) lab at GSFC, and is monitoring three of their five spacecraft. We are scheduled to install REACH in the Mid-sized Explorer (MIDEX) lab, which will allow us to monitor up to six more spacecraft. The process of installing and using our "research" software in an operational environment has provided many insights into which parts of REACH are a step forward and which of our ideas are missteps. Our paper explores both the new concepts in spacecraft health-and-safety visualization, the difficulties of such systems in the operational environment, and the cost and safety issues of multi-spacecraft missions.

Maks, Lori↗
NASA NTRS2006

Constrained Kalman Filtering Via Density Function Truncation for Turbofan Engine Health Estimation

Kalman filters are often used to estimate the state variables of a dynamic system. However, in the application of Kalman filters some known signal information is often either ignored or dealt with heuristically. For instance, state variable constraints (which may be based on physical considerations) are often neglected because they do not fit easily into the structure of the Kalman filter. This paper develops an analytic method of incorporating state variable inequality constraints in the Kalman filter. The resultant filter truncates the PDF (probability density function) of the Kalman filter estimate at the known constraints and then computes the constrained filter estimate as the mean of the truncated PDF. The incorporation of state variable constraints increases the computational effort of the filter but significantly improves its estimation accuracy. The improvement is demonstrated via simulation results obtained from a turbofan engine model. The turbofan engine model contains 3 state variables, 11 measurements, and 10 component health parameters. It is also shown that the truncated Kalman filter may be a more accurate way of incorporating inequality constraints than other constrained filters (e.g., the projection approach to constrained filtering).

Simon, Dan↗
NASA NTRS2017

Digital Model-Based Engineering: Expectations, Prerequisites, and Challenges of Infusion

Digital model-based engineering (DMbE) is the use of digital artifacts, digital environments, and digital tools in the performance of engineering functions. DMbE is intended to allow an organization to progress from documentation-based engineering methods to digital methods that may provide greater flexibility, agility, and efficiency. The term 'DMbE' was developed as part of an effort by the Model-Based Systems Engineering (MBSE) Infusion Task team to identify what government organizations might expect in the course of moving to or infusing MBSE into their organizations. The Task team was established by the Interagency Working Group on Engineering Complex Systems, an informal collaboration among government systems engineering organizations. This Technical Memorandum (TM) discusses the work of the MBSE Infusion Task team to date. The Task team identified prerequisites, expectations, initial challenges, and recommendations for areas of study to pursue, as well as examples of efforts already in progress. The team identified the following five expectations associated with DMbE infusion, discussed further in this TM: (1) Informed decision making through increased transparency, and greater insight. (2) Enhanced communication. (3) Increased understanding for greater flexibility/adaptability in design. (4) Increased confidence that the capability will perform as expected. (5) Increased efficiency. The team identified the following seven challenges an organization might encounter when looking to infuse DMbE: (1) Assessing value added to the organization. Not all DMbE practices will be applicable to every situation in every organization, and not all implementations will have positive results. (2) Overcoming organizational and cultural hurdles. (3) Adopting contractual practices and technical data management. (4) Redefining configuration management. The DMbE environment changes the range of configuration information to be managed to include performance and design models, database objects, as well as more traditional book-form objects and formats. (5) Developing information technology (IT) infrastructure. Approaches to implementing critical, enabling IT infrastructure capabilities must be flexible, reconfigurable, and updatable. (6) Ensuring security of the single source of truth (7) Potential overreliance on quantitative data over qualitative data. Executable/ computational models and simulations generally incorporate and generate quantitative vice qualitative data. The Task team also developed several recommendations for government, academia, and industry, as discussed in this TM. The Task team recommends continuing beyond this initial work to further develop the means of implementing DMbE and to look for opportunities to collaborate and share best practices.

Hale, J. P.↗
NASA NTRS1974

A 2.5 kW advanced technology ion thruster

A program has been conducted in order to improve the performance characteristics of 30 cm thrusters. This program was divided into three distinct, but related tasks: (1) the discharge chamber and component design modifications proposed for inclusion in the engineering model thruster were evaluated and engineering specifications were verified; (2) thrust losses which result from the contributions of double charged ions and nonaxial ion trajectories to the ion beam current were measured and (3) the specification and verification of power processor and control requirements of the engineering model thruster design were demonstrated. Proven design modifications which provide improved efficiencies are incorporated into the engineering model thruster during a structural re-design without introducing additional delay in schedule or new risks. In addition, a considerable amount of data is generated on the relation of double ion production and beam divergence to thruster parameters. Overall thruster efficiency is increased from 68% to 71% at full power, including corrections for double ion and beam divergence thrust losses.

Poeschel, R. L.↗