SEARCH · Search NASA

Results for “exit presentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Reduction of background noise induced by wind tunnel jet exit vanes

The NASA-Langley 4 x 7 m wind tunnel develops low frequency flow pulsations at certain velocity ranges during open throat mode operation, affecting the aerodynamics of the flow and degrading the resulting model test data. Triangular vanes attached to the trailing edge of flat steel rails, mounted 10 cm from the inside of the jet exit walls, have been used to reduce this effect; attention is presently given to methods used to reduce the inherent noise generation of the vanes while retaining their pulsation reduction features.

Martin, R. M.↗

NASA NTRS1988

V/STOL aircraft and the problem of jet-induced suckdown

The suckdown condition encountered when jet propelled, Vertical/Short Takeoff and Landing aircraft hover near the ground is described. A discussion of this ground effect problem and how it is being investigated is followed by a more detailed description of one of the methods researchers are using to investigate the basic mechanisms that influence the suckdown condition. Specific parameters that are taken into account include the height of the jet above the ground, jet exit conditions, and model geometry. Data from a current investigation is presented along with some conclusions from other recent investigations in order to relate the significance of some of the parameters influencing suckdown. Suggestions are made for additional testing methods which might be useful to researchers investigating the mechanisms involved in jet induced suckdown.

Carlisle, Cherianne↗

NASA NTRS1992

Aircraft ground test and subscale model results of axial thrust loss caused by thrust vectoring using turning vanes

The NASA-Dryden F/A-18 high alpha research vehicle was modified to incorporate three independently controlled turning vanes located aft of the primary nozzle of each engine to vector thrust for pitch and yaw control. Ground measured axial thrust losses were compared with the results from a 14.25 pct. cold jet model for single and dual vanes inserted up to 25 degs into the engine exhaust. Data are presented for nozzle pressure ratios of 2.0 and 3.0 and nozzle exit areas of 253 and 348 sq in. The results indicate that subscale nozzle test results properly predict trends but underpredict the full scale results by approx. 1 to 4.5 pct. in thrust loss.

Johnson, Steven A.↗

NASA NTRS1985

Rn-222 tracing and stable isotope measurements of biogenic gas fluxes from methane saturated sediments

Transport of reduced biogenic gases from anoxic sediments and soils to the atmosphere can be quantitatively studied through measurement of radon-222/radium-226 disequilibrium. In previous work, seasonal variations in biogenic gas transport mechanisms, net fluxes and overall composition were documented. Now presented are direct field measurements of radon-222 activity in gases exiting organic rich sediments which show their usefulness for tracing of the stripping of dissolved biogenic gases from within the sediment column and transport via bubble ebullition. Methane is depleted in deuterium during the summer as compared with winter months and is in general lighter than in most marine sediments signaling the probable importance of acetate as an important precursor molecule. The significant seasonal isotopic variations observed illustrate the importance of understanding mechanisms and rates of biogenic gas production in order to interpret observed tropospheric isotopic data.

Martens, Christopher S.↗

NASA NTRS1999

New Method for Calibration for Hyperspectral Pushbroom Imaging Systems

A new, easy-to-implement approach for achieving highly accurate spectral and radiometric calibration of array-based, hyperspectral pushbroom imagers is presented in this paper. The equivalence of the plane of the exit port of an integrating sphere to a Lambertian surface is utilized to provide a field-filling radiance source for the imager. Several different continuous wave lasers of various wavelengths and a quartz-tungsten-halogen lamp internally illuminate the sphere. The imager is positioned to "stare" into the port, and the resultant data cube is analyzed to determine wavelength calibrations, spectral widths of channels, radiometric characteristics, and signal-to-noise ratio, as well as an estimate of signal-to-noise performance in the field. The "smile" (geometric distortion of spectra) of the system can be quickly ascertained using this method. As the price and availability of solid state laser sources improve, this technique could gain wide acceptance.

Ryan, Robert↗

NASA NTRS2007

Dual-Pump CARS Temperature and Species Concentration Measurements in a Supersonic Combustor

The dual-pump coherent anti-Stokes Raman scattering (CARS) method was used to measure temperature and the mole fractions of N2 and O2 in a supersonic combustor. Experiments were conducted in NASA Langley Research Center s Direct Connect Supersonic Combustion Test Facility. In this facility, H2 and oxygen-enriched air burn to increase the enthalpy of the simulated air test gas. This gas is expanded through a Mach 2 nozzle and into a combustor model consisting of a short constant-area section followed by a small rearward-facing step and another constant-area section. At the end of this straight section, H2 fuel is injected at Mach 2 and at a 30 angle with respect to the freestream. One wall of the duct then expands at a 3 angle for over 1 meter. The ensuing combustion is probed optically through ports in the side of the combustor. Dual-pump CARS measurements were performed at the facility nozzle exit and at four planes downstream of fuel injection. Maps are presented of the mean temperature, as well as N2 and O2 mean mole fraction fields. Correlations between fluctuations of the different measured parameters are also presented.

O'Byrne, S.↗

NASA NTRS2020

On Orbit Flight Testing of the Roll-Out Solar Array

The Roll-Out Solar Array (ROSA) is an innovative, lightweight solar array with a flexible substrate that makes use of the stored strain energy in its composite structural members to provide deployment without the use of motors while still packaging efficiently. The ROSA flight experiment was launched to the International Space Station (ISS)on June 3rd, 2017 as a part of the eleventh SpaceX commercial resupply mission. After two weeks of storage, ROSA was extracted from the Dragon spacecraft, deployed, and put through a week of tests to verify its structural characteristics as well as the performance of photovoltaics. The structural dynamics experiments included active excitation of out-of-plane bending modes, and a study of the thermal-structural interaction of the structure during day-night transitions. Data was gathered from a small number of accelerometers located at key points on the solar array and from cameras observing numerous photogrammetry targets spread out over the structure and the photovoltaic blanket. The goal in this effort was to better understand the performance of ROSA and to improve modeling efforts for future designs of similar solar arrays. Of particular interest are the first few system modes and mode shapes of the array, the amount of structural damping present, and degree of structural-thermal interaction seen during eclipse exit.

ROSA↗

NASA NTRS1974

Distributed educated throat stability bypass to increase the stable airflow range of a Mach 2.5 inlet with 60-percent internal contraction

The results of an experimental investigation to increase the stable airflow operating range of a supersonic mixed-compression inlet are presented. A distributed educated throat stability-bypass entrance configuration was tested. In terms of diffuser-exit corrected airflow, a large inlet stable airflow range of about 16.1 percent was obtained if a constant pressure was maintained in the bypass plenum. Limited unstart angle of attack data are presented.

Shaw, R. J.↗

NASA NTRS1993

Statistical modeling of capture, association, and exit-channel dynamics in the CH3(+)/CH3CN system

The ion-molecule CH3(+) + CH3CN reaction is presently modeled by means of a master equation treatment incorporating weak collisions. The parameter required for the Rice-Ramsberger-Kassel-Markus (RRKM) treatment is derived from an ab initio investigation of the energy surface in question, and a means of including the capture rate coefficients in the RRKM approach is developed in which only the hindered dipole rotation is coupled in the reaction coordinate at large separations. Unimolecular rate coefficients for the (CH3CNCH3+)-activated complex are calculated for all product channels in the 300-600 K temperature range.

Smith, S. C.↗

NASA NTRS1985

Background noise measurements from jet exit vanes designed to reduced flow pulsations in an open-jet wind tunnel

Many open jet wind tunnels experience pulsations of the flow which are typically characterized by periodic low frequency velocity and pressure variations. One method of reducing these fluctuations is to install vanes around the perimeter of the jet exit to protrude into the flow. Although these vanes were shown to be effective in reducing the fluctuation content, they can also increase the test section background noise level. The results of an experimental acoustic program in the Langley 4- by 7-Meter Tunnel is presented which evaluates the effect on tunnel background noise of such modifications to the jet exit nozzle. Noise levels for the baseline tunnel configuration are compared with those for three jet exit nozzle modifications, including an enhanced noise reduction configuration that minimizes the effect of the vanes on the background noise. Although the noise levels for this modified vane configuration were comparable to baseline tunnel background noise levels in this facility, installation of these modified vanes in an acoustic tunnel may be of concern because the noise levels for the vanes could be well above background noise levels in a quiet facility.

Hoad, D. R.↗

NASA NTRS2001

Experimental Investigation of Transition to Turbulence as Affected By Passing Wakes

This paper presents experimental results from a study of the effects of periodically passing wakes upon laminar-to-turbulent transition and separation in a low-pressure turbine passage. The test section geometry is designed to simulate unsteady wakes in turbine engines for studying their effects on boundary layers and separated flow regions over the suction surface by using a single suction surface and a single pressure surface to simulate a single turbine blade passage. Single-wire, thermal anemometry techniques are used to measure time-resolved and phase averaged, wall-normal profiles of velocity, turbulence intensity and intermittency at multiple streamwise locations over the turbine airfoil suction surface. These data are compared to steady-state wake-free data collected in the same geometry to identify the effects of wakes upon laminar-to-turbulent transition. Results are presented for flows with a Reynolds number based on suction surface length and stage exit velocity of 50,000 and an approach flow turbulence intensity of 2.5%. While both existing design and experimental data are primarily concerned with higher Reynolds number flows (Re greater than 100,000), recent advances in gas turbine engines, and the accompanying increase in laminar and transitional flow effects, have made low-Re research increasingly important. From the presented data, the effects of passing wakes on transition and separation in the boundary layer, due to both increased turbulence levels and varying streamwise pressure gradients are presented. The results show how the wakes affect transition. The wakes affect the flow by virtue of their difference in turbulence levels and scales from those of the free-stream and by virtue of their ensemble- averaged velocity deficits, relative to the free-stream velocity, and the concomitant changes in angle of attack and temporal pressure gradients. The relationships between the velocity oscillations in the freestream and the unsteady velocity profile shapes in the near-wall flow are described. In this discussion is support for the theory that bypass transition is a response of the near-wall viscous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.cous layer to pressure fluctuations imposed upon it from the free-stream flow. Recent transition models are based on that premise. The data also show a significant lag between when the wake is present over the surface and when transition begins.

Kaszeta, Richard W.↗

NASA NTRS2018

Conceptual Aerodynamic Design of a Tail-Cone Thruster System Under Axi-Symmetric Inlet Distortion

This paper presents a conceptual design of a tail-cone thruster system which is operating under an axisymmetric inlet distortion. An effort to realize the targeted fuel burn saving that was proposed in NASA's STARC_ABL aircraft design is made through a CFD (Computational Fluid Dynamics)-based design approach. This method employs three iterative steps to exploit the CFD tools until the design requirements are met: a quasi-2D through-flow model to design the fan/EGV (Exit Guide Vane), a 3-D RANS (Reynolds Averaging Navier-Stokes) simulation of the single blade row to account for the inlet/fan and the EGV/nozzle interaction, and a 3-D RANS simulation of the airframe with a propulsor installed - propulsion airframe integration (PAI). The design requirements which include the thrust, and shaft power of the propulsor are matched throughout the evaluations coming from two CFD domains, i.e., the turbo-machinery and the PAI. During the switch between these different computational domains, the inlet and exit profiles are matched via the correction factors of the body-force model. The present tail-cone thruster (TCT) aerodynamic design leverages a low-pressure ratio fan (FPR=1.2 to approximately 1.25) of which the camber-line angles are predicted by a quasi-2D through-flow model. The quasi-2D model is derived to analyze the radially distorted flow resulting from the ingested boundary layer at the inlet. It also estimates the appropriate velocity vectors of the metal angles of the fan and EGV which is subjected to different types of vortex at the fan exit. The baseline geometry is revisited and its internal flow-path and exhaust cone are redesigned to illustrate the strong correlation among the components of the propulsor in the PAI domain. The peak efficiency point of the fan/EGV with respect to the blade counts, also known as solidity, and rotational speed is chosen for the cruise condition via parametric studies. The corresponding performance maps are presented. The resulting performance metrics of the new conceptual design of the BLI (Boundary Layer Ingestion) propulsor are analyzed and compared with these of the baseline in the PAI aspect. Finally, ideas of the CFD based design of a BLI propulsor are discussed based on the observations drawn from the numerical results.

Inlet↗

NASA NTRS1993

Phase 2: HGM air flow tests in support of HEX vane investigation

Following the start of SSME certification testing for the Pratt and Whitney Alternate Turbopump Development (ATD) High Pressure Oxidizer Turbopump (HPOTP), cracking of the leading edge of the inner HEX vane was experienced. The HEX vane, at the inlet of the oxidizer bowl in the Hot Gas Manifold (HGM), accepts the HPOTP turbine discharge flow and turns it toward the Gaseous Oxidizer Heat Exchanger (GOX HEX) coil. The cracking consistently initiated over a specific circumferential region of the hex vane, with other circumferential locations appearing with increased run time. Since cracking had not to date been seen with the baseline HPOTP, a fluid-structural interaction involving the ATD HPOTP turbine exit flowfield and the HEX inner vane was suspected. As part of NASA contract NAS8-36801, Pratt and Whitney conducted air flow tests of the ATD HPOTP turbine turnaround duct flowpath in the MSFC Phase 2 HGM air flow model. These tests included HEX vane strain gages and additional fluctuating pressure gages in the turnaround duct and HEX vane flowpath area. Three-dimensional flow probe measurements at two stations downstream of the turbine simulator exit plane were also made. Modifications to the HPOTP turbine simulator investigated the effects on turbine exit flow profile and velocity components, with the objective of reproducing flow conditions calculated for the actual ATD HPOTP hardware. Testing was done at the MSFC SSME Dynamic Fluid Air Flow (Dual-Leg) Facility, at air supply pressures between 50 and 250 psia. Combinations of turbine exit Mach number and pressure level were run to investigate the effect of flow regime. Information presented includes: (1) Descriptions of turbine simulator modifications to produce the desired flow environment; (2) Types and locations for instrumentation added to the flow model for improved diagnostic capability; (3) Evaluation of the effect of changes to the turbine simulator flowpath on the turbine exit flow environment; and (4) Comparison of the experimental turbine exit flow environment to the environment calculated for the ATD HPOTP.

Cox, G. B., Jr.↗

NASA NTRS1975

A theoretical/experimental program to develop active optical pollution sensors: Quantitative remote Raman lidar measurements of pollutants from stationary sources

Typical pollutant gas concentrations at the stack exits of stationary sources can be estimated to be about 500 ppm under the present emission standards. Raman lidar has a number of advantages which makes it a valuable tool for remote measurements of these stack emissions. Tests of the Langley Research Center Raman lidar at a calibration tank indicate that night measurements of SO2 concentrations and stack opacity are possible. Accuracies of 10 percent are shown to be achievable from a distance of 300 m within 30 min integration times for 500 ppm SO2 at the stack exits. All possible interferences were examined quantitatively (except for the fluorescence of aerosols in actual stack emissions) and found to have negligible effect on the measurements. An early test at an instrumented stack is strongly recommended.

Poultney, S. K.↗

NASA NTRS1993

Use of Blade Lean in Turbomachinery Redesign

Blade lean is used to improve the uniformity of exit flow distributions from turbomachinery blading. In turbines, it has been used to control secondary flows by tailoring blade turning to reduce flow overturning and underturning and to create more uniform loss distributions from hub to shroud. In the present study, the Pump Consortium centrifugal impeller has been redesigned using blade lean. The flow at the exit of the baseline impeller had large blade-to-blade variations, creating a highly unsteady flow for the downstream diffuser. Blade lean is used to redesign the flow to move the high loss fluid from the suction side to the hub, significantly reducing blade-toblade variations at the exit.

Moore, John↗

NASA NTRS1992

Compact in-line laser radial shear interferometer

A compact in-line radial shearing interferometer using laser as a light source is presented. The interferometer is made out of a cube-type beam splitter so that the two opposite surfaces are generated with different curvatures while the normal to the entrance and exit surfaces are in the same line. The interferometer is simple to make and easy to align. Aberration analysis of the interferometer is also presented. Some applications of the interferometer for testing lenses and infrared optical systems and for accessing the quality of an emerging wave front from the exit slit of a monochromator are suggested.

Shukla, R. P.↗

NASA NTRS1974

Forward slanted slot throat stability bypass to increase the stable airflow range of a Mach 2.5 inlet with 60 percent internal contraction

The results of an experimental investigation to increase the stable airflow operating range of a supersonic mixed-compression inlet are presented. Two forward-slanted slot stability-bypass entrance configurations were tested. In terms of diffuser-exit corrected airflow, a large inlet stable airflow range of 18.5 percent was obtained with the superior configuration if a constant pressure was maintained in the bypass plenum. Limited unstart angle-of-attack data are presented.

Shaw, R. J.↗

NASA NTRS1975

Comparison of experimental and theoretical boundary-layer separation for inlets at incidence angle at low-speed conditions

Comparisons between experimental and theoretical Mach number distributions and separation locations are presented for the internal surfaces of four different subsonic inlet geometries with exit diameters of 13.97 centimeters. The free stream Mach number was held constant at 0.127, the one-dimensional throat Mach number ranged from 0.49 to 0.71, and the incidence angle ranged from 0 deg to 50 deg. Generally good agreement was found between the theoretical and experimental surface Mach number distributions as long as no flow separation existed. At high incidence angles, where separation was obvious in the experimental data, the theory predicted separation on the lip. At lower incidence angles, the theoretical results indicated diffuser separation which was not obvious from the experimental surface Mach number distributions. As incidence angle was varied from 0 deg to 50 deg, the predicted separation location shifted from the diffuser region to the inlet highlight. Relatively small total pressure losses were obtained when the predicted separation location was greater than 0.6 of the distance between the highlight and the diffuser exit.

Felderman, E. J.↗