Results for “extended scan” — Page 13

NASA NTRS1976

Computer image processing in marine resource exploration

Pictographic data or imagery is commonly used in marine exploration. Pre-existing image processing techniques (software) similar to those used on imagery obtained from unmanned planetary exploration were used to improve marine photography and side-scan sonar imagery. Features and details not visible by conventional photo processing methods were enhanced by filtering and noise removal on selected deep-sea photographs. Information gained near the periphery of photographs allows improved interpretation and facilitates construction of bottom mosaics where overlapping frames are available. Similar processing techniques were applied to side-scan sonar imagery, including corrections for slant range distortion, and along-track scale changes. The use of digital data processing and storage techniques greatly extends the quantity of information that can be handled, stored, and processed.

Paluzzi, P. R.↗

NASA NTRS2025

Magnetic Resonance Imaging (MRI) to Assess Changes to Trabecular Microarchitecture (Trb µArch) of the Hip

BACKGROUND . Calculated loss rates in trabecular (Trb) volumetric bone mineral density (vBMD), in astronauts after return from 6-month long-duration (LD) spaceflight, are rapid relative to menopause-induced loss rates and could contribute to the observed lack of recovery. Perforations in the Trb bony struts, skeletal fragility and fractures [5] have been associated with the rapid rate of bone loss in women due to menopause. The more rapid loss rate observed in astronauts could be inducing similar, irreversible losses of trabecular connectivity as seen in cadaver studies of female skeletons. These changes are not detectable by DXA technology and would not be discovered in astronauts during scheduled, triennial DXA testing for primary osteoporosis. High-resolution-peripheral quantitative computed tomography (HR-pQCT) of the lower leg have detected losses in Trb vBMD (vBMD) and changes in Trb microarchitecture (µArch) in astronauts immediately following routine 6-month spaceflights and continuing in some individuals for 1 or more years postflight with no signs of recovery. Resolution of these microarchitectural changes by whole body QCT, especially in the deeply embedded hip bone, is prohibitive due to excessive and unsafe radiation exposures. While HR-pQCT has sufficient resolution to study Trb µArch at safe and lower radiation exposure testing is restricted only to the lower leg and wrist. Hence, a technology to detect detrimental changes to Trb µArch in astronauts, especially of the hip, is needed to inform type and timing of countermeasures to irreversible deficits (preflight, inflight and postflight). METHODS . This HRP-funded study (2023-2027) will verify the sensitivity of a protocol for MRI scanning (on a 3T Siemens Vida) to detect changes to hip Trb µArch in persons following spinal cord injury (SCI); skeletal immobilization below the spinal lesion will serve as an analog for non-weight-bearing during spaceflight. The study period has been extended by 1 yr due to delayed Richmond IRB approval in Y1. A 3T MRI protocol will characterize serial changes in hip Trb µArch in SCI patients from time of admission at the Richmond VA Medical Center to their scheduled annual exam 12-months later. SCI patients with age, sex, and physical characteristics like ISS astronauts will be consented. The ability of 3T MRI hip scan to discriminate loss of trabecular connectivity subjects with SCI will be compared to age- and sex-matched ambulatory controls. A comparison between HR-pQCT and MRI measurements at the ankle (distal tibia) of study subjects will also be performed. A modified DXA scan analysis (3D-Shaper) will also be verified as a potential method for monitoring concurrent changes in hip Trb bone over 12-month. SIGNIFICANCE . Deliverables: a surveillance method for assessing for irreversible losses of connectivity and how skeletal changes after LD spaceflight(s) would modify the terrestrial risk of primary osteoporosis.

Spinal Cord Injury↗

NASA NTRS2025

Magnetic Resonance Imaging (MRI) to Assess Changes to Trabecular Microarchitecture (Trb µArch) of the Hip

BACKGROUND . Calculated loss rates in trabecular (Trb) volumetric bone mineral density (vBMD), in astronauts after return from 6-month long-duration (LD) spaceflight, are rapid relative to menopause-induced loss rates and could contribute to the observed lack of recovery. Perforations in the Trb bony struts, skeletal fragility and fractures [5] have been associated with the rapid rate of bone loss in women due to menopause. The more rapid loss rate observed in astronauts could be inducing similar, irreversible losses of trabecular connectivity as seen in cadaver studies of female skeletons. These changes are not detectable by DXA technology and would not be discovered in astronauts during scheduled, triennial DXA testing for primary osteoporosis. High-resolution-peripheral quantitative computed tomography (HR-pQCT) of the lower leg have detected losses in Trb vBMD (vBMD) and changes in Trb microarchitecture (µArch) in astronauts immediately following routine 6-month spaceflights and continuing in some individuals for 1 or more years postflight with no signs of recovery. Resolution of these microarchitectural changes by whole body QCT, especially in the deeply embedded hip bone, is prohibitive due to excessive and unsafe radiation exposures. While HR-pQCT has sufficient resolution to study Trb µArch at safe and lower radiation exposure testing is restricted only to the lower leg and wrist. Hence, a technology to detect detrimental changes to Trb µArch in astronauts, especially of the hip, is needed to inform type and timing of countermeasures to irreversible deficits (preflight, inflight and postflight). METHODS . This HRP-funded study (2023-2027) will verify the sensitivity of a protocol for MRI scanning (on a 3T Siemens Vida) to detect changes to hip Trb µArch in persons following spinal cord injury (SCI); skeletal immobilization below the spinal lesion will serve as an analog for non-weight-bearing during spaceflight. The study period has been extended by 1 yr due to delayed Richmond IRB approval in Y1. A 3T MRI protocol will characterize serial changes in hip Trb µArch in SCI patients from time of admission at the Richmond VA Medical Center to their scheduled annual exam 12-months later. SCI patients with age, sex, and physical characteristics like ISS astronauts will be consented. The ability of 3T MRI hip scan to discriminate loss of trabecular connectivity subjects with SCI will be compared to age- and sex-matched ambulatory controls. A comparison between HR-pQCT and MRI measurements at the ankle (distal tibia) of study subjects will also be performed. A modified DXA scan analysis (3D-Shaper) will also be verified as a potential method for monitoring concurrent changes in hip Trb bone over 12-month. SIGNIFICANCE . Deliverables: a surveillance method for assessing for irreversible losses of connectivity and how skeletal changes after LD spaceflight(s) would modify the terrestrial risk of primary osteoporosis.

Risk Surveillance↗

DOE OSTI2021

A Bayesian Approach to the Eagar–Tsai Model for Melt Pool Geometry Prediction with Implications in Additive Manufacturing of Metals

Here, this paper focuses on improving the melt pool geometry predictions and quantifying uncertainties using an adapted version of the Eagar–Tsai (E–T) model that incorporates temperature-dependent properties of the material as well as powder conditions. Additionally, Bayesian inference is employed to predict distributions for the E–T model input parameters of laser absorptivity and powder bed porosity by incorporating experimental results into the analysis. Monte Carlo uncertainty propagation is then used with these parameter distributions to estimate the melt pool depth and associated uncertainty. Our results for the 316L stainless steel suggest that both the absorptivity and powder bed porosity are strongly influenced by the laser power. In contrast, the scanning speed has only a marginal effect on both the absorptivity and powder bed porosity. We constructed a printability map using the Bayesian E–T model based on power-dependent input parameter values to demonstrate the merit of the approach. The Bayesian approach improved the accuracy in predicting the keyhole regions in the laser power-scan speed parameter space for the 316L stainless steel. Although applied to a specific adaptation of the E–T model, the method put forth can be extended to quantify uncertainties in other numerical models as well as in the estimation of unknown parameters.

316L Stainless Steel (SS).↗

DOE OSTI2024

Recycling of silver from silicon solar cells by laser debonding

A laser-debonding approach to silver electrode recovery from solar cells is presented to address the critical need for efficient and eco-friendly recycling methods. The study explores the use of UV nanosecond and IR continuous-wave lasers to precisely debond silver electrodes from silicon wafers. By optimizing parameters like laser power, scan speed, and the number of passes, intact silver electrical contact lines were recovered from solar cells. Scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) analysis confirmed the successful separation of silver from silicon wafers. Furthermore, an increase in the number of laser passes led to the production of silver microparticles, as validated by morphology and compositional studies using EDS. The estimated silver is approximately 90 mg for the Si solar cells of 15.4 * 15.4 cm 2 used in the study. To achieve a large area recovery of silver, a MATLAB code incorporating detection algorithms and specific criteria to automate laser scanning by accurately identifying the location of silver electrodes was developed. This presented laser debonding method is not confined to silicon solar cells but can be extended to other solar cell types featuring metal electrodes, offering a versatile solution. By minimizing the use of hazardous chemicals and reducing operational costs, the developed process aligns with the imperative of environmentally responsible photovoltaic waste management.

14 SOLAR ENERGY↗

DOE OSTI2020

Atomic-Level Understanding of Surface Reconstruction Based on Li[Ni x Mn y Co 1–x–y ]O 2 Single-Crystal Studies

The stability of cathode particle surfaces that are directly exposed to the electrolyte is one of the most crucial and determining factors for cathode performance at high operating voltages. Theory has predicted a strong dependence of surface stability on chemical compositions as well as surface facets of layered oxides, yet conflicting results on the correlations exist as most experimental studies focus on cycled secondary particles recovered from composite electrodes. Here, we synthesize well-formed Li[Ni x Mn y Co 1–x–y ]O 2 (NMC) single-crystal samples, carefully define pristine surface properties, and then monitor their evolution with cycling. Atomic-resolution scanning transmission electron microscopy (STEM) imaging and electron energy loss spectroscopy (EELS) analysis show the formation of a surface reconstruction layer (SRL) as well as an extended surface reduction layer on pristine, Li-permeable non-(001) surfaces, even before cycling. We reveal a transition region with chemical gradient, in which the layered structure gradually densifies and eventually transforms into the SRL on the top surface. Contrary to these observations, no SRL is observed on pristine, Li-impermeable (001) surfaces, revealing the facet-dependent nature of surface reconstructions during particle synthesis. Upon electrochemical cycling, significant composition-and facet-dependent SRL growth is observed. The driving force and mechanism for surface reconstruction are further discussed. The present study provides insights into the origin as well as the nature of SRLs, highlighting the significance of surface engineering in cathode material optimization.

25 ENERGY STORAGE↗

DOE OSTI2025

Morphological Degradation of Oxygen Evolution Reaction-Electrocatalyzing Nickel Selenides at Industrially Relevant Current Densities

We investigated electrodeposited nanoparticulate nickel selenide (pre)catalysts that transform into nickel oxides/ oxyhydroxides under oxygen evolution reaction conditions in alkaline solutions. Previous studies of this transformation were conducted at lower current densities than those of industrial relevance (≥1 A cm −2 ). We used ultramicroelectrodes (UMEs) to achieve such current densities, benefiting from their small size, ensuring low absolute currents and low ohmic drop but high current densities. Morphological degradation of the catalyst material was only observed at current densities exceeding 1 A cm −2 but not for smaller ones. Using X-ray absorption, Xray photoemission spectroscopy, and X-ray diffraction, we confirmed that the degradation was accompanied by the literature-known transformation of nanoparticulate Ni 3 Se 2 (bulk)/NiSe (surface) into nickel oxyhydroxide. The transformation of the precatalyst goes along with a significant improvement in the charge transfer kinetics observed by decreasing Tafel slopes with ongoing experimental time extracted from cyclic voltammetry (CV) experiments and electrochemical impedance spectroscopy (EIS) in the high-frequency range. However, these kinetic improvements are accompanied by limitations in mass transport concluded from decreasing current responses at high overpotentials in CVs and increasing impedance in the low-frequency range of the EIS spectra after extended CV cycling. These mass transport limitations originated from morphological degradations at the UME exceeding 1 A cm −2 which we proved by applying identical location scanning electron microscopy. This has not been reported in studies that have been limited to lower current densities before. Our findings showcase how UMEs can be used to study (pre)catalysts (herein nickel selenides) under current densities of industrial relevance in the absence of ohmic drop-related ambiguities, combined with in-depth materials characterization studies, e.g., identical location microscopy and advanced spectroscopic methods. This approach enables direct evaluation and comparison of catalyst materials and thus demonstrates how to overcome long-standing limitations of electrocatalyst design and testing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1972

Anomalous minima in Cen X-3.

Report of an observation made with a rocket-borne argon-methane proportional counter, which was equipped with a 'Mylar' window and was sensitive to X rays in the range from 0.2 to 10 keV. During a scan of the galactic plane, the detector passed directly over the location of Cen X-3 at a roll rate of 1 deg per second. An extended minimum of X-ray flux was observed. It is concluded that the anomalous effect is intrinsic to the source.

Margon, B.↗

NASA NTRS1980

Comparison of conventionally measured sea surface temperature and wind speed with data retrieved from satellite-borne microwave radiometry

The Scanning Multichannel Microwave Radiometer aboard both the Seasat and Nimbus-7 satellites was designed to estimate sea surface temperature (SST) and wind speed (WS) over an extended range of atmospheric conditions. The retrieval technique is described briefly, and it is demonstrated in a case study that the instrument design goals (SST:1.5 C; WS:2 m/s) appear to be feasible.

Hofer, R.↗

NASA NTRS1987

Diffusion length measurements in bulk and epitaxially grown 3-5 semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic techniques used was charge collection microscopy also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended generation and point generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations, or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗

NASA NTRS1991

Image construction from the IRAS survey

IRAS survey data can be used successfully to produce images of extended objects. The major difficulties, i.e., nonuniform sampling, different response functions for each detector, and varying signal-to-noise levels for each detector for each scan, have been resolved. The results of three different image construction techniques are compared: coaddition, constrained least-squares, and maximum entropy. The maximum entropy result is superior. An image of the galaxy M51 with an average spatial resolution of 45 arcsecods, using 60 microns survey data is presented. This exceeds the telescope diffraction limit of about 1 minute of arc at this wavelength.

Bontekoe, T. R.↗

NASA NTRS1993

Vision based obstacle detection and grouping for helicopter guidance

Electro-optical sensors can be used to compute range to objects in the flight path of a helicopter. The computation is based on the optical flow/motion at different points in the image. The motion algorithms provide a sparse set of ranges to discrete features in the image sequence as a function of azimuth and elevation. For obstacle avoidance guidance and display purposes, these discrete set of ranges, varying from a few hundreds to several thousands, need to be grouped into sets which correspond to objects in the real world. This paper presents a new method for object segmentation based on clustering the sparse range information provided by motion algorithms together with the spatial relation provided by the static image. The range values are initially grouped into clusters based on depth. Subsequently, the clusters are modified by using the K-means algorithm in the inertial horizontal plane and the minimum spanning tree algorithms in the image plane. The object grouping allows interpolation within a group and enables the creation of dense range maps. Researchers in robotics have used densely scanned sequence of laser range images to build three-dimensional representation of the outside world. Thus, modeling techniques developed for dense range images can be extended to sparse range images. The paper presents object segmentation results for a sequence of flight images.

Sridhar, Banavar↗

NASA NTRS2002

Recent Results from Galileo PPR at Io: Orbits I31 and I32

Recent Galileo PPR (Photo-Polarimeter Radiometer) results will be shown, including global day and nighttime maps, high latitude regional maps, and high-resolution scans across hotspots and from pole to pole. SO2 vapor pressure, global heatflow, and hotspot power outputs are estimated. Additional information is contained in the original extended abstract.

Rathbun, J. A.↗

NASA NTRS2012

Simulations of Infrared Radiances Over a Deep Convective Cloud System Observed During TC4: Potential for Enhancing Nocturnal Ice Cloud Retrievals

Retrievals of ice cloud properties using infrared measurements at 3.7, 6.7, 7.3, 8.5, 10.8, and 12.0 microns can provide consistent results regardless of solar illumination, but are limited to cloud optical thicknesses tau < approx.6. This paper investigates the variations in radiances at these wavelengths over a deep convective cloud system for their potential to extend retrievals of tau and ice particle size D(sub e) to optically thick clouds. Measurements from the Moderate Resolution Imaging Spectroradiometer Airborne Simulator--ASTER, the Scanning High-resolution Interferometer Sounder, the Cloud Physics Lidar (CPL), and the Cloud Radar System (CRS) aboard the NASA ER-2 aircraft during the NASA TC4 (Tropical Composition, Cloud and Climate Coupling) experiment flight during 5 August 2007, are used to examine the retrieval capabilities of infrared radiances over optically thick ice clouds. Simulations based on coincident in-situ measurements and combined cloud tau from CRS and CPL measurements are comparable to the observations. They reveal that brightness temperatures at these bands and their differences (BTD) are sensitive to tau up to approx.20 and that for ice clouds having tau > 20, the 3.7 - 10.8 microns and 3.7 - 6.7 microns BTDs are the most sensitive to D(sub e). Satellite imagery appears consistent with these results. Keywords: clouds; optical depth; particle size; satellite; TC4; multispectral thermal infrared

Minnis, Patrick↗

NASA NTRS2012

Simulations of Infrared Radiances Over a Deep Convective Cloud System Observed During TC4- Potential for Enhancing Nocturnal Ice Cloud Retrievals

Retrievals of ice cloud properties using infrared measurements at 3.7, 6.7, 7.3, 8.5, 10.8, and 12.0 microns can provide consistent results regardless of solar illumination, but are limited to cloud optical thicknesses tau < approx.6. This paper investigates the variations in radiances at these wavelengths over a deep convective cloud system for their potential to extend retrievals of tau and ice particle size D(sub e) to optically thick clouds. Measurements from the Moderate Resolution Imaging Spectroradiometer Airborne Simulator--ASTER, the Scanning High-resolution Interferometer Sounder, the Cloud Physics Lidar (CPL), and the Cloud Radar System (CRS) aboard the NASA ER-2 aircraft during the NASA TC4 (Tropical Composition, Cloud and Climate Coupling) experiment flight during 5 August 2007, are used to examine the retrieval capabilities of infrared radiances over optically thick ice clouds. Simulations based on coincident in-situ measurements and combined cloud tau from CRS and CPL measurements are comparable to the observations. They reveal that brightness temperatures at these bands and their differences (BTD) are sensitive to tau up to approx.20 and that for ice clouds having tau > 20, the 3.7 - 10.8 microns and 3.7 - 6.7 microns BTDs are the most sensitive to D(sub e). Satellite imagery appears consistent with these results. Keywords: clouds; optical depth; particle size; satellite; TC4; multispectral thermal infrared

CRS and CPL↗

DOE OSTI2022

It’s Not What You Take Up, It’s What You Keep: How Discoveries from Diverse Disciplines Directed the Development of the FDG PET/CT Scan

Although imaging glucose metabolism with positron emission tomography combined with X-ray CT (FDG-PET/CT) has become a standard diagnostic modality for the discovery and surveillance of malignant tumors and inflammatory processes, its origins extend back to more than a century of notable discoveries in the fields of inorganic and organic chemistry, nuclear physics, mathematics, biochemistry, solute transport physiology, metabolism, and imaging, accomplished by pioneering and driven investigators, of whom at least ten were recipients of the Nobel Prize. These tangled and diverse roots eventually coalesced into the FDG-PET/CT method, that through its many favorable characteristics inherent in the isotope used ( 18 F), the accurate imaging derived from coincidence detection of positron annihilation radiation combined with computed tomography, and the metabolic trapping of 2-deoxy-2-[ 18 F] fluoro-d-glucose (FDG) in tissues, provides safety, sensitivity, and specificity for tumor and inflammation detection. Here, the authors hope that this article will increase the appreciation among its readers of the insight, creativity, persistence, and drive of the many investigators who made this technique possible. This article is followed by a review of the many applications of FDG-PET/CT to the gastrointestinal tract and hepatobiliary system (Mandelkern in Dig Dis Sci 2022)

2-DG↗

NASA NTRS1981

Observations of the giant radio lobes region of Centaurus A with SAS 3

Observations of the X-ray flux from the extended radio lobes of the galaxy Centaurus A obtained with the SAS 3 observatory are reported. The 15 x 15 deg region that includes the lobes was mapped by superposing data from raster scans with the horizontal tubular collimator detectors, which have a 1.7 deg FWHM circular field of view. Data obtained is consistent with the presence of superposed emission from the point sources NGC 5128 and MX 1312-42, a previously unreported source detected by the Einstein Observatory IPC. Fluxes of 4.63 + or - 0.14 x 10 to the -10th and 4.6 + or - 0.6 x 10 to the -11th ergs/sq cm per sec were measured for NGC 5128 and MX 1312-42, respectively, with best fit power law spectra of indices 0.83 + or - 0.04 and 0.62 + or - 0.10 and hydrogen column densities of 1.23 + or - 0.10 x 10 to the 23rd and 9.7 + or - 15.0 x 10 to the 21st atoms/sq cm. Results imply an upper limit of 2.9 x 10 to the 11th for the X-ray emission from the extended radio lobes of Cen A between 2 and 10 keV, which indicates a lower limit to the magnetic field in the lobes of 1.6 x 10 to the -6th gauss.

Marshall, F. J.↗

DOE OSTI2025

Measurement of directed flow in Au + Au collisions at $\sqrt{s{NN}}$ = 19.6 and 27 GeV with the STAR event plane detector

In heavy-ion collision experiments, the global collectivity of final-state particles can be quantified by anisotropic flow coefficients (𝑣 𝑛 ) . The first-order flow coefficient, also referred to as the directed flow (𝑣 1 ), describes the collective sideward motion of produced particles and nuclear fragments in heavy-ion collisions. It carries information on the very early stage of the collision, especially at large pseudorapidity (𝜂), where it is believed to be generated during the nuclear passage time. Directed flow therefore probes the onset of bulk collective dynamics during thermalization, providing valuable experimental guidance to models of the pre-equilibrium stage. In 2018, the Event Plane Detector (EPD) was installed in STAR and used for the Beam Energy Scan phase-II (BES-II) data taking. The combination of EPD (2.1 < |𝜂| < 5.1) and high-statistics BES-II data enables us to extend the 𝑣 1 measurement to the forward and backward 𝜂 regions. In this paper, we present the measurement of 𝑣 1 over a wide 𝜂 range in Au + Au collisions at $\sqrt{s_{NN}}$ = 19.6 and 27 GeV using the STAR EPD. The results of the analysis at $\sqrt{s_{NN}}$ = 19.6 GeV exhibit excellent consistency with the previous PHOBOS measurement, while elevating the precision of the overall measurement. The increased precision of the measurement also revealed finer structures in heavy-ion collisions, including a potential observation of the first-order event-plane decorrelation. Multiple physics models were compared to the experimental results. Only a transport model and a three-fluid hybrid model can reproduce a sizable 𝑣 1 at large 𝜂 as was observed experimentally. The model comparison also indicates 𝑣 1 at large 𝜂 might be sensitive to the QGP phase transition.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗