SEARCH · Search NASA
Results for “fast charge”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Toward a high-voltage fast-charging pouch cell with TiO 2 cathode coating and enhanced battery safety
Nickel-rich layered lithium transition metal oxides, LiNi x Co y Mn 1-x-y O 2 , are key cathode materials for high-energy lithium-ion batteries owing to their high specific capacity. However, the commercial deployment of nickel-rich oxides has been hampered by their poor thermostability and insufficient cycle life. In this work full batteries with uncoated and TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathodes and graphite anodes are compared in terms of electrochemical performance and safety behavior. The battery using a TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode exhibited better cyclic performance at high cutoff voltage. Electrochemical impedance spectroscopy analysis indicated that the TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode gave the battery a more stable charge transfer resistance. Transmission electron microscopy demonstrated that TiO 2 coating reduced accumulation of the cathode electrolyte interface layer on the particle surface. Time-of-flight secondary ion mass spectrometry demonstrated that TiO 2 coating markedly enhanced the interface stability of the cathode particle and protected the particle from serious etching by the electrolyte. Accelerating rate calorimetry revealed that the trigger temperature of thermal runaway for the battery using TiO 2 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 as cathode material was 257 °C, which was higher than that of the battery with the uncoated LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathode (251 °C). In situ X-ray diffraction during heating demonstrated that this enhanced safety can be attributed to the suppressed phase evolution of the coated cathode material.
Titanium Niobium Oxide: From Discovery to Application in Fast-Charging Lithium-Ion Batteries
Lithium-ion batteries are essential for portable technology and are now poised to disrupt a century of combustion-based transportation. The electrification revolution could eliminate our reliance on fossil fuels and enable a clean energy future; advanced batteries would facilitate this transition. However, owing to the demanding performance, cost, and safety requirements, it is challenging to translate new materials from laboratory prototypes to industrial-scale products. This Perspective describes that journey for a new lithium-ion battery anode material, TiNb 2 O 7 (TNO). TNO is intended as an alternative to graphite or Li 4 Ti 5 O 12 with better rate and safety characteristics than the former and higher energy density than the latter. The high capacity of TNO stems from the multielectron redox of Nb 5+ to Nb 3+ , its operating voltage window well above the Li + /Li reduction potential prevents lithium dendrite formation, and its open crystal structure leads to high-power performance. Nevertheless, the creation of a practical TNO anode was nonlinear and nontrivial. Its history is built on 30 years of fundamental science that preceded its application as a battery anode, and its battery development included a nearly 30-year gap. The insights and lessons contained in this Perspective, many of them acquired firsthand, serve two purposes: (i) to unite the disparate studies of TiNb 2 O 7 into a coherent modern understanding relevant to its application as a battery material and (ii) to highlight briefly some of the challenges faced when scaling up a new material that affect TiNb 2 O 7 as well as new electrode candidates more generally.
Amorphization as a Pathway to Fast Charging Kinetics in Atomic Layer Deposition-Derived Titania Films for Lithium Ion Batteries
Abstract not provided
Spatial Quantification of Microstructural Degradation during Fast Charge in 18650 Lithium-Ion Batter
Explore the source record for details and available documents.
Metallicity, Atomic Disorder, and Li-Ion Storage in Fast-Charging Anodes
Oxides of Nb with Wadsley-Roth shear structures comprise a family of stable, high-rate anode materials for Li-ion batteries. A particular pair of them offers the unusual opportunity to test how important metallic conduction of the starting electrode is for electrode performance. The selected pair of compounds with similar 4 × 3 Wadsley-Roth block structures are insulating Ti 2 Nb 10 O 29 and metallic Nb 12 O 29 . A combination of diffraction, electrochemistry, magnetic measurements, and entropic potential measurements is employed to establish key findings for these two anode materials. We find that starting with a metallic oxide is not especially advantageous over a comparable material that readily transitions into a metallic state upon lithiation. Second, the rate performance appears to be dictated by ion mobility, and atomic Ti/Nb disorder in Ti 2 Nb 10 O 29 contributes to improved capacity retention at high rates by suppressing Li-ion ordering. However, subtle details in the nature of redox processes make Nb 12 O 29 a slightly better electrode material for long-term cycling at slower rates.
Production of fast-charge Zn-based aqueous batteries via interfacial adsorption of ion-oligomer complexes
Abstract Aqueous zinc batteries are attracting interest because of their potential for cost-effective and safe electricity storage. However, metallic zinc exhibits only moderate reversibility in aqueous electrolytes. To circumvent this issue, we study aqueous Zn batteries able to form nanometric interphases at the Zn metal/liquid electrolyte interface, composed of an ion-oligomer complex. In Zn||Zn symmetric cell studies, we report highly reversible cycling at high current densities and capacities (e.g., 160 mA cm −2 ; 2.6 mAh cm −2 ). By means of quartz-crystal microbalance, nuclear magnetic resonance, and voltammetry measurements we show that the interphase film exists in a dynamic equilibrium with oligomers dissolved in the electrolyte. The interphase strategy is applied to aqueous Zn||I 2 and Zn||MnO 2 cells that are charged/discharged for 12,000 cycles and 1000 cycles, respectively, at a current density of 160 mA cm −2 and capacity of approximately 0.85 mAh cm −2 . Finally, we demonstrate that Zn||I 2 -carbon pouch cells (9 cm 2 area) cycle stably and deliver a specific energy of 151 Wh/kg (based on the total mass of active materials in the electrode) at a charge current density of 56 mA cm −2 .
Growing single-crystalline seeds on lithiophobic substrates to enable fast-charging lithium-metal batteries
Not provided.
Fast charging of energy-dense lithium-ion batteries
Not provided.
Fast-charge high-voltage layered cathodes for sodium-ion batteries
Not provided.
Traction Inverter Integrated On-Board DC Fast Charging through Partial Power Processing
This paper introduces an innovative on-board integrated DC charging approach through partial power processing (PPP) in a traction inverter system. The proposed system, incorporating a series-connected partial power dual-active-bridge (DAB) converter, efficiently regulates the DC link voltage to achieve an optimal bus voltage for traction operation across a wide speed and torque range. Leveraging partial and bidirectional power processing, the battery current during charging is precisely regulated without the need for external DC-DC charging equipment, ensuring seamless integration to a DC hub with different voltage levels. This advanced integration also endows the system with bidirectional power exchange capability to/from the external DC hub, i.e., vehicle-to-DC (V2DC).
Optimized System for On-Route Fast Charging of Battery-Electric Shuttle Buses
Electrifying cars, buses, and trucks is an attractive means of reducing energy use and emissions because it involves more efficient drivetrain components and minimal restructuring of the transportation network. Transit buses, driving fixed routes, help minimize driver range anxiety by properly sizing energy storage systems. A major challenge to fully electrifying transit buses is providing the amount of energy they consume in a day of driving. To enable a full day of operation without charging, batteries need to be large, which could be expensive and heavy. This work utilizes real-world transit bus data used in a battery-electric drivetrain model to co-optimize charger locations, charger power levels, and vehicle battery sizes.
Multiport Control with Partial Power Processing in Solid-State Transformer for PV, Storage, and Fast-Charging Electric Vehicle Integration
This article proposes a multiport control method to enable partial power processing (PPP) in a medium-voltage (MV) multiport solid-state transformer (SST). MV multiport SSTs are promising in integrating low-voltage DC sources or loads such as solar photovoltaic, energy storage, and electric vehicles into smart grids without bulky line-frequency transformers. Compared to voltage-source SST, current-source (CS) SST features single-stage isolated bidirectional AC/AC, AC/DC, or DC/DC conversion using an inductive DC link. For a multiport CS SST, it is revealed in this article that the PPP capability can be enabled through the proposed control without extra hardware, different from the case of voltage-source converters where special hardware architecture is required for the PPP. With the PPP, most power exchange between LV ports is processed by only a fraction of the entire conversion stage, leading to reduced DC-link current, volume, loss, and improved efficiency. The proposed multiport PPP control scheme is analyzed to verify the advantages across a wide voltage and power range against conventional full power processing (FPP) multiport control, using the soft-switching solid-state transformer (S4T) with reduced conduction loss as an example. Comparative experimental results based on a SiC three-port S4T prototype verify the effectiveness of the proposed PPP scheme against the FPP scheme under both steady state and dynamic conditions. Here, the DC-link current reduction is measured to be more than 36%. Significantly, the proposed multiport PPP control scheme is generic and applicable to any hard-switching or soft-switching CS SSTs without extra hardware.