Search NASA⌕ Search

SEARCH · Search NASA

Results for “gradient plasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Comprehensive Report For Proposed Elevated Temperature Elastic Perfectly Plastic (EPP) Code Cases Representative Example Problems

Background: The current rules in the nuclear section of the ASME Boiler and Pressure Vessel (B&PV) Code , Section III, Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200F (650C)1. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (E-PP) analysis methods and which are expected to be applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature 2, 3, and have been recently revised to incorporate comments and simplify their application. The revised code cases have been developed. Task Objectives: The goal of the Sample Problem task is to exercise these code cases through example problems to demonstrate their feasibility and, also, to identify potential corrections and improvements should problems be encountered. This will provide input to the development of technical background documents for consideration by the applicable B&PV committees considering these code cases for approval. This task has been performed by Hollinger and Pease of Becht Engineering Co., Inc., Nuclear Services Division and a report detailing the results of the E-PP analyses conducted on example problems per the procedures of the E-PP strain limits and creep-fatigue draft code cases is enclosed as Enclosure 1. Conclusions: The feasibility of the application of the E-PP code cases has been demonstrated through example problems that consist of realistic geometry (a nozzle attached to a semi-hemispheric shell with a circumferential weld) and load (pressure; pipe reaction load applied at the end of the nozzle, including axial and shear forces, bending and torsional moments; through-wall transient temperature gradient) and design and operating conditions (Levels A, B and C).

36 MATERIALS SCIENCE↗

Chemical Upcycling of Polyethylene, Polypropylene, and Mixtures to High-Value Surfactants

Conversion of plastic wastes to fatty acids is an attractive means to supplement the sourcing of these high-value, high-volume chemicals. We report a method for transforming polyethylene (PE) and polypropylene (PP) at ~80% conversion to fatty acids with number-average molar masses of up to ~700 and 670 daltons, respectively. The process is applicable to municipal PE and PP wastes and their mixtures. Temperature-gradient thermolysis is the key to controllably degrading PE and PP into waxes and inhibiting the production of small molecules. The waxes are upcycled to fatty acids by oxidation over manganese stearate and subsequent processing. PP ..beta..-scission produces more olefin wax and yields higher acid-number fatty acids than does PE ..beta..-scission. We further convert the fatty acids to high-value, large-market-volume surfactants. Industrial-scale technoeconomic analysis suggests economic viability without the need for subsidies.

deconstruction↗

Failure Analysis for Molten Salt Thermal Energy Storage Tanks for In-Service CSP Plants

Thermal Energy Storage (TES) is a fundamental component in concentrating solar power (CSP) plants to increase the plant's dispatchability, capacity factor, while reducing the levelized cost of electricity. In central receivers CSP plants, nitrate molten salts have been used for several years for operation temperatures of up to 565 degrees C. Despite many efforts to advance nitrate salt to higher operation temperatures (even considering a replacement with molten chloride salts) to achieve higher energy conversion efficiencies, the 565 degrees C temperature is currently considered the state-of-the art. Although molten salt tanks have been broadly deployed in commercial CSP plants worldwide, several failures have been reported in these tanks after a few months or years of operation, causing significant economic loss and mistrust in CSP technologies. Most of these failures are associated with the infancy of the technology and multiple issues related to tank design, fabrication, commissioning, and aggressive operation. A technical standard dedicated to the design and fabrication of molten nitrate TES tanks does not exist today. Current in-service molten salt tanks have been generally designed based on the American Petroleum Institute's (API) 650 and ASME Section II standards. The API 650 code provides guidelines for dimensions and fabrication for oil storage tanks up to 260 degrees C. The ASME standard provides allowable stress values for various materials at a range of temperatures and conditions. Both standards seem to be limited for molten salt TES tanks where high temperatures, thermal cycling, and transient conditions are expected. In 2020, NREL released the Concentrating Solar Power Best Practices Study (NREL/TP-5500-75763) that summarized multiple issues in CSP plants, along with potential alternatives and recommendations to address those issues based on information collected from participants representing about 80% of operating CSP plants in the world. One of the recommendations from this study was the development of accurate and validated models to evaluate the plant's transient operation, capable of capturing the effect of short-term clouds and operator response, while being flexible in being adapted to various spatial and temporal resource data. The "Failure Analysis for Molten Salt Thermal Energy Tanks for In-Service CSP Plants" project was inspired on this recommendation and was focused on (1) the development and validation of a physics-based model for a representative, commercial-scale molten salt tank, (2) performing simulations to evaluate the behavior of the tank as a function of typical plant operation conditions, (3) understanding tank failures mechanisms, (4) determining the residual stress and distortion in the tank floor after welding fabrication and evaluating their impact in the stresses developed in the tank during operation, (5) assessing the impact of key operation parameters on the temperature and stress distribution, (6) conduct a preliminary evaluation of design features to reduce stress and improve tank's reliability, and (7) estimate the tank's service life based on the stress developed under diverse operation scenarios. From the analysis conducted in the project and presented in this report, it was found that maximum stresses surpassing the yield strength point of the stainless steel (SS) 347H are developed on the tank floor near the perimeter. These large stresses are strongly influenced by the initial residual stresses and distortion of the tank floor after welding fabrication. During operation, large stresses are developed in the tank floor at high operation temperatures with large salt inventory levels during transient operation. High stresses are also related to elevated temperature gradients in the tank floor that could be attributed to insufficient mixing within the salt inflow and the salt inventory. Based on the analysis, creep is the predominant failure mechanism. However, the large stress levels could favor the plastic deformation into buckles, and crack formation due to stress relaxation cracking during cycle operation. A lifetime below 3 years was estimated for the typical plant operation conditions and a specific initial residual stress and deformation distribution of the tank floor. The estimated life agrees with the service time to failure reported in several commercial molten salt tanks. Desing and operation guidelines can be extracted from the analysis presented in this report, which could be adopted by tank manufacturers and CSP operators to advance toward an ultimate solution for tank failures by reducing residual and operational stresses to achieve a tank service life of more than 30 years. Addressing failures in molten salt TES tanks is fundamental for the CSP industry's survivability, but it is also important for other industrial and power generation applications using this technology, including nuclear and concentrating solar thermal.

14 SOLAR ENERGY↗

Rapid Relaxation and Embrittlement of Zr-based Bulk Metallic Glasses by Electropulsing

Mechanical relaxation and embrittlement of Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glasses were achieved rapidly by the direct current electropulsing treatment. The temperature profile was recorded by an infrared camera and it was found to be non-uniform in the treated specimen. Specifically, temperatures below the glass transition temperature, near and above the crystallization temperature could be ach- ieved, respectively, at different locations in the same treated specimen. Two sets of nanoindentation were conducted. While the first set investigated the mechanical properties of three individually elec- tropulsed specimens with different conditions, the second set indented a single treated specimen along its temperature gradient. Both sets of indentation revealed that by Joule heating to different tempera- tures, relaxation, embrittlement, and crystallization were significantly accelerated by electrical pulses. Results suggest that electropulsing provides an opportunity to simultaneously achieve plastic forming and mechanical property control of metallic glasses.

Yiu, P↗

Resolving intragranular stress fields in plastically deformed titanium using point-focused high-energy diffraction microscopy

Abstract The response of a polycrystalline material to a mechanical load depends not only on the response of each individual grain, but also on the interaction with its neighbors. These interactions lead to local, intragranular stress concentrations that often dictate the initiation of plastic deformation and consequently the macroscopic stress–strain behavior. However, very few experimental studies have quantified intragranular stresses across bulk, three-dimensional volumes. In this work, a synchrotron X-ray diffraction technique called point-focused high-energy diffraction microscopy (pf-HEDM) is used to characterize intragranular deformation across a bulk, plastically deformed, polycrystalline titanium specimen. The results reveal the heterogenous stress distributions within individual grains and across grain boundaries, a stress concentration between a low and high Schmid factor grain pair, and a stress gradient near an extension twinning boundary. This work demonstrates the potential for the future use of pf-HEDM for understanding the local deformation associated with networks of grains and informing mesoscale models. Graphical abstract

36 MATERIALS SCIENCE↗

In-depth quantitative analysis of the microstructures produced by Surface Mechanical Attrition Treatment (SMAT)

Electron BackScattered Diffraction (EBSD) maps are used to characterize quantitatively the graded microstructure formed by Surface Mechanical Attrition Treatment (SMAT) and applied here to the 316L stainless steel. In particular, the analysis of GNDs – coupled with relevant and reliable criteria – was used to depict the thickness of each zone identified in the SMAT-affected layers: (i) the “ultrafine grain” (UFG) zone present at the extreme top surface, (ii), the “transition zone” where grains were fragmented under the heavy plastic deformation and, finally, (iii) the “deformed zone” where initial grains are simply deformed. The interest of this procedure is illustrated through the comparative analysis of the effect of some SMAT processing parameters (amplitude of vibration and treatment duration). The UFG and transition zones are more significantly modified than the overall affected thickness under our tested conditions. - Highlights: • EBSD maps are used to characterize quantitatively the microstructure of SMAT treated samples. • Calculation of the GND density to quantify strain gradients • A new method to depict the different zone thicknesses in the SMAT affected layer • Effects of SMAT processing parameters on the surface microstructure evolution.

36 MATERIALS SCIENCE↗

Solid Phase Gradient Alloying Method via ShAPE

Alloying has been used to confer desirable properties to various metallic systems since the bronze age. For example, Ni, Mn, and Cr are alloyed into an Fe matrix to make steel, which has improved strength and corrosion resistance (as displayed in Fig. 1). In addition to the type of alloying elements, the amount of alloying elements added into a matrix is also very critical for a material’s mechanical property, physical property, machinability, and cost. Conventionally, new alloys are discovered by combining alloy precursors and elemental constituents into a mixture and melting them together. The solidified product or ingot represents a usually non-homogeneous combination of the chemistry with a microstructure dictated by the physics of solidification. It is time and energy intensive to optimize the alloying amounts via the casting process and hence, economically not conducive to rapid alloy discovery. In addition, the cast microstructure seen in the as-cast ingot is often not the ideal, nor even desired structure for optimized performance. Cast materials often need further processing such as homogenization, annealing, and deformation work put in through rolling, forging, extruding, etc. to have favorable microstructures and properties. A faster method to discover new alloy combinations and evaluate them in their worked or processed form is needed. Recently, Laser Engineered Net Shaping was applied to fabricate gradient compositional material for alloy designing. However, the mechanical properties of this gradient alloy were poor due to the existence of impurities, oxidation and cracks that are inherent in the melt-solidification process. Because of these limitations, we propose to use a solid-phase process (ShAPE) to create bulk materials (extrudates) that vary in composition from one end of the extruded solid to the other. Various manufacturing methods for alloy design including conventional casting method, laser based combinatorial method and current solid phase gradient alloying method are displayed and compared in Fig. 2. ShAPE machine and a schematic of ShAPE process are displayed in Fig. 3. Starting material is processed by a rotating and plunging die to form an extrudate. We are proposing through this methodology to invent a new, bulk-scale combinatorial technique. With this novel technique, alloying element can be dissolved into the matrix with a continued gradient without bulk melting. Formation of inter-metallics and defects originating from melt processing can be avoided. In addition, the ShAPE process creates the mixed alloy chemistry, and meanwhile subjects the material to severe plastic strain, which induces the favorable “worked” microstructure. Products from the ShAPE process can be tested in hardness directly providing a path to rapid evaluation of mechanical properties. The ability to create graded structures using friction stir processing (FSP) has been demonstrated, however using the ShAPE process we believe will lead to much faster and higher fidelity results. When combined with high throughput screening methods of physical, mechanical and microstructural property characterization, efficiency and accuracy of alloy design can be significantly improved.

36 MATERIALS SCIENCE↗

Through-Thickness Strain Gradient in a Hot-Rolled Al-Mg Alloy Obtained by Nanoindentation and Glancing Angle X-Ray Diffraction

Combined nanoindentation and glancing angle X-ray diffraction (GAXD) methods were used to study the mechanical properties of near-surface microstructures (NSMs) of a hot-rolled 5xxx aluminum alloy. Nanoindentations with a sharp indenter were carried out with penetration depth ranging from 250 nm to 4500 nm at the near-surface regions as well as the bulk of the hot-rolled alloy. The primary indentation parameter presented here was the hardness, given that plastic strain obtained from GAXD experiment could be correlated with the hardness value. Analysis of nanoindentation hardness results proved that NSMs of this alloy on average were harder than the bulk due to the presence of different surface features discussed here. The GAXD experiments were performed between a minimum incident angle 0.025°, equivalent to 765 nm penetration depth, and a maximum angle 1°, equivalent to 3000 nm penetration depth. The strain-induced broadening in the diffraction peaks was calculated by the Williamson–Hall technique. Both indentation hardness and glancing angle diffraction results confirmed strain gradient as a function of depth in the NSMs of the alloy. Both techniques also showed that the thickness of the subsurface layer (i.e., several micrometers below the surface) of hot-rolled sample was approximately 2.44 μm at the tested areas. Additionally, reported results provided evidence for the ability to use glancing angle X-ray diffraction as a nondestructive tool for the measurement of subsurface layers' thickness as well as microstrain (non-uniform or plastic strain) as a function of depth.

36 MATERIALS SCIENCE↗

A High-Rate, Single-Crystal Model including Phase Transformations, Plastic Slip, and Twinning

An anisotropic, rate-­dependent, single-­crystal approach for modeling materials under the conditions of high strain rates and pressures is provided. The model includes the effects of large deformations, nonlinear elasticity, phase transformations, and plastic slip and twinning. It is envisioned that the model may be used to examine these coupled effects on the local deformation of materials that are subjected to ballistic impact or explosive loading. The model is formulated using a multiplicative decomposition of the deformation gradient. A plate impact experiment on a multi-­crystal sample of titanium was conducted. The particle velocities at the back surface of three crystal orientations relative to the direction of impact were measured. Molecular dynamics simulations were conducted to investigate the details of the high-­rate deformation and pursue issues related to the phase transformation for titanium. Simulations using the single crystal model were conducted and compared to the high-­rate experimental data for the impact loaded single crystals. The model was found to capture the features of the experiments.

36 MATERIALS SCIENCE↗

Three-dimensional local residual stress and orientation gradients near graphite nodules in ductile cast iron [3D local residual stress and orientation gradients near graphite nodules in ductile cast iron]

A synchrotron technique, differential aperture X-ray microscopy (DAXM), has been applied to characterize the microstructure and analyze the local mesoscale residual elastic strain fields around graphite nodules embedded in ferrite matrix grains in ductile cast iron. Compressive residual elastic strains are measured with a maximum strain of ~6.5–8 × 10 –4 near the graphite nodules extending into the matrix about 20 μm, where the elastic strain is near zero. The experimental data are compared with a strain gradient calculated by a finite element model, and good accord has been found but with a significant overprediction of the maximum strain. This is discussed in terms of stress relaxation during cooling or during storage by plastic deformation of the nodule, the matrix or both. Furthermore, relaxation by plastic deformation of the ferrite is demonstrated by the formation of low energy dislocation cell structure also quantified by the DAXM technique.

36 MATERIALS SCIENCE↗

Two-dimensional parametric design of short pulse laser driven iron opacity experiments

High intensity short pulse lasers are commonly used to create high temperature and high density plasmas. These plasmas are used to study fundamental properties such as the equation of state and opacity. The targets often use small-diameter, thin buried layers of the materials of interest, surrounded by a tamper of low atomic number material such as plastic. Computational modeling is used to design and interpret experiments with short pulse lasers. Most of the modeling to date has assumed one-dimensional plane-parallel geometry. In this paper, the effects of radial gradients in the irradiation of thin planar targets are studied with one- and two-dimensional radiation/hydrodynamic simulations. It is found that the main effect of radial gradients is the averaging of plasma conditions and x-ray emission over the pattern of irradiation. Additionally, differences between one- and two-dimensional simulations arise because the plasma conditions and x-ray emission are, in general, nonlinear functions of the temperature of the plasma and thereby also nonlinear functions of the irradiation intensity. The differences increase with the ratio of the buried layer radius to the laser spot radius. The root mean square difference in the inferred iron L-shell opacity is less than 30% when the ratio is less than 1.0 and about 70% when the ratio is 1.5.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mix and match—a versatile equilibrium approach for hybrid colloidal synthesis

Colloidal synthesis is a powerful bottom-up approach for programmed self-assembly which holds promise for both research and industry. While diverse, each synthetic process is typically restricted to a specific chemistry. Many applications however require composite materials, whereas a chemical equilibrium can typically only match one material but not the other. Here, a scalable general approach is presented, alleviating the dependency on a specific chemical reaction, by resorting to a mechanical equilibrium; an isopycnic density-gradient-step is tailored to form clusters with prescribed composition. Valence control is demonstrated, making dimers, trimers, and tetramers with purity as high as 96%. The measured kinetics shows a scaleable throughput. The density gradient step plays a dual role of both filtering out undesired products and concentrating the target structures. The “Mix-and-Match” approach is general, and applies to a broad range of colloidal matter: diverse material compositions (plastics, glasses, and emulsions); a range of colloidal interactions (van der Waals, Coulomb, and DNA hybridization); and a spectrum of sizes (nanoscale to multiple micrometers). Lastly, the strength of the method is displayed by producing a monodisperse suspension from a highly polydisperse emulsion. The ability to combine colloids into architectures of hybrid materials has applications in pharmaceuticals, cosmetics, and photonics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SurFE-XD (Surface curvature-driven Finite Elements model for Diffusion under eXtreme conditions)

SurFE-XD is a mesoscale finite element framework to model surface diffusion under mutliphysics environments. The code uses legacy C++ library dolphin wrapped with python in a FEniCS driven unified form language and just-in-time (JIT) compilation setting. The purpose of the release is to attract wide-ranging usage of the code along with publication supplementation to support reproducibility of scientific data. SurFE-XD has been originally conceived under the LDRD-DR funding for “High-Gradient (C-BAND) Breakdown tolerant accelerator materials project. Currently SrFE-XD support electrostatics and Thermo-elasticity driven surface diffusion kernels. Releasing the code will also enable to include contributions from other physical regimes e.g., plasticity and electrodynamics etc as well portability to GPU-based platforms.

Bagchi, Soumendu↗

Achieving High Efficiency in Reduced Order Modeling for Large Scale Polycrystal Plasticity Simulations

Reduced order models for the nonlinear response of heterogeneous microstructures typically require a construction (or training) stage to build the reduced order basis. In this manuscript, an efficient model construction strategy for the eigenstrain homogenization method (EHM) is presented. The proposed strategy relies on a parallel, element-by-element, conjugate gradient solver. Near linear scaling has been achieved with respect to the number of degrees of freedom used to resolve the microstructure. Linear scaling with respect to the number of pre-analyses required to construct the reduced order model (ROM) follows from the EHM formulation. Furthermore, a parallel implementation for fast evaluation of the constructed ROM has been developed using shared memory parallelization. It has been shown that for large microstructures with ≈ 10,000 grains, the total computational cost of evaluating the nonlinear response of a polycrystal could be reduced by approximately an order of magnitude using 32 cores with respect to serial ROM simulation. The present methodology has been verified using an additively manufactured polycrystalline microstructure of a nickel-based superalloy, Inconel 625. The capability of the developed framework to construct a ROM for such large microstructures, as well as the ability of the ROM to predict average and local quantities of interest has been demonstrated.

microscale↗

A Single-Lap Joint Adhesive Bonding Optimization Method Using Gradient and Genetic Algorithms

A natural process for any engineer, scientist, educator, etc. is to seek the most efficient method for accomplishing a given task. In the case of structural design, an area that has a significant impact on the structural efficiency is joint design. Unless the structure is machined from a solid block of material, the individual components which compose the overall structure must be joined together. The method for joining a structure varies depending on the applied loads, material, assembly and disassembly requirements, service life, environment, etc. Using both metallic and fiber reinforced plastic materials limits the user to two methods or a combination of these methods for joining the components into one structure. The first is mechanical fastening and the second is adhesive bonding. Mechanical fastening is by far the most popular joining technique; however, in terms of structural efficiency, adhesive bonding provides a superior joint since the load is distributed uniformly across the joint. The purpose of this paper is to develop a method for optimizing single-lap joint adhesive bonded structures using both gradient and genetic algorithms and comparing the solution process for each method. The goal of the single-lap joint optimization is to find the most efficient structure that meets the imposed requirements while still remaining as lightweight, economical, and reliable as possible. For the single-lap joint, an optimum joint is determined by minimizing the weight of the overall joint based on constraints from adhesive strengths as well as empirically derived rules. The analytical solution of the sin-le-lap joint is determined using the classical Goland-Reissner technique for case 2 type adhesive joints. Joint weight minimization is achieved using a commercially available routine, Design Optimization Tool (DOT), for the gradient solution while an author developed method is used for the genetic algorithm solution. Results illustrate the critical design variables as a function of adhesive properties and convergences of different joints based on the two optimization methods.

Smeltzer, Stanley S., III↗

ASSESSMENT OF RESIDUAL STRESSES ON U10MO ALLOY BASED MONOLITHIC MINI-PLATES DURING HOT ISOSTATIC PRESSING

This article presents an assessment of the residual stress field on U10Mo alloy based monolithic fuel plates and their elasto-plastic response to the thermo-mechanical fabrication process. Monolithic plate-type fuel for research and test reactors is a new fuel form proposed and developed by Idaho National Laboratory (INL) to accomplish higher uranium densities in the reactor core and allow multi-fold reduction of fuel enrichment. Identification of the 3D residual field is critical for benchmarking the new design and understanding the overall performance of the new plate-type fuels. To define fuel-cladding stress-strain characteristics, a new thermo-mechanical finite element model was developed. Material properties at high temperatures and material plasticity were considered carefully to improve the accuracy as the Hot Pressing temperature reaches the melting temperature of the cladding material. By using elasto-thermo-plastic material models, it was determined that the cladding material (AL6061-TO) is exposed to tensile stress field and exceeds its proportional limits, while the fuel foil (U10Mo) is under compression and remains below its yield limit. It was shown that the residual stresses would govern the overall behavior of the plates, and therefore, should not be neglected. In particular, the simulations have revealed the existence of stress gradients at the fuel/cladding interface, thus emphasizing the necessity of excellent bonding quality at the bond region for mechanical endurance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A finite element formulation for deformation twinning induced strain localization in polycrystal magnesium alloys

Deformation twinning induces shear strain localization in hexagonal close-packed crystals and is critical for the material’s ductility and failure. Cracks often occur at twin-twin or twin-grain boundary intersections and propagate along twin bands. However, most crystal plasticity models for deformation twinning are based on a “pseudo-slip” approach and do not capture the localized deformation associated with the formation of each discrete twin band. The few exceptions are discrete twin models that involve very complex numerical algorithms and are often compromised in accuracy due to the numerical convergence. These factors make the discrete twin models hard to adopt. This paper proposes a modification to the conventional finite element weak form, to fully incorporate a twin-induced heterogeneous deformation that does not depend on the “pseudo-slip” assumption. The model starts by splitting the deformation gradient into elastic-slip-twinning components. The twin-induced deformation gradient component is computed separately by solving a microstructural evolution problem and then implemented into finite element weak form by constructing a global “twin-force” vector. The constitutive update (e.g., in the user-defined material subroutine, or UMAT, for ABAQUS) therefore avoids dealing with the twinning and recovers to the form of a regular slip-based crystal plasticity model. The results presented here indicate that the twin-induced strain localization and the associated stress-reversal phenomena near the twin band were naturally captured in the model, which was validated against an in-situ synchrotron X-ray micro-diffraction experiment.

36 MATERIALS SCIENCE↗

Changes in leaf economic trait relationships across a precipitation gradient are related to differential gene expression in a C 4 perennial grass

Summary The leaf economics spectrum (LES) describes a suite of functional traits that consistently covary at large spatial and taxonomic scales. Despite its importance at these larger scales, few studies have examined the major drivers of intraspecific variation in the LES – phenotypic plasticity and standing genetic variation. Using experimental precipitation manipulations, we examined whether covariation among leaf economics traits and selection on leaf economics traits and trait combinations change as diverse genotypes of the widespread perennial grass Panicum virgatum are exposed to differences in precipitation. We also used RNA‐Seq to examine whether groups of co‐expressed genes that align with leaf economics traits function in processes hypothesized to underlie the LES. Water availability impacted leaf economics trait covariation in important ways – covariation between leaf economics traits and selection on covariation between traits (i.e. correlational selection) tended to be strongest when water availability was high. Additionally, many genes associated with leaf economics traits functioned in processes that may explain how the LES originates, such as chloroplasts, cell walls, and nitrogen metabolism. Water availability is likely an important modulator of selection and evolution of the LES in P. virgatum that can be better understood by examining gene expression.

Heckman, Robert W. [Department of Integrative Biol↗