SEARCH · Search NASA

Results for “hexagonal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Emergency cooling analysis for the loss of coolant malfunction

This report examines the dynamic response of a conceptual space power fast-spectrum lithium cooled reactor to the loss of coolant malfunction and several emergency cooling concepts. The results show that, following the loss of primary coolant, the peak temperatures of the center most 73 fuel elements can range from 2556 K to the region of the fuel melting point of 3122 K within 3600 seconds after the start of the accident. Two types of emergency aftercooling concepts were examined: (1) full core open loop cooling and (2) partial core closed loop cooling. The full core open loop concept is a one pass method of supplying lithium to the 247 fuel pins. This method can maintain fuel temperature below the 1611 K transient damage limit but requires a sizable 22,680-kilogram auxiliary lithium supply. The second concept utilizes a redundant internal closed loop to supply lithium to only the central area of each hexagonal fuel array. By using this method and supplying lithium to only the triflute region, fuel temperatures can be held well below the transient damage limit.

Peoples, J. A.↗

NASA NTRS1972

Superconductivity in the alkali metal intercalates of molybdenum disulphide

The complete series of alkali metals, lithium through cesium, have been intercalated into molybdenum disulphide, using both the liquid ammonia and vapor techniques. All the intercalates with the exception of lithium yielded full superconducting transitions with onset temperatures of 6 K for AxMoS2(Ax=K,Rb,Cs) and 4 K for BxMoS2(Bx=Li,Na). The superconducting transition for lithium was incomplete down to 1.5 K. Stoichiometries and unit cell parameters have been determined for the intercalation compounds. Both rhombohedral and hexagonal polymorphs of MoS2 have been intercalated and found to exhibit the same superconductivity behavior. The nature of the extraneous superconducting transition of some intercalated samples on exposure to air was elucidated.

Somoano, R. B.↗

NASA NTRS1973

Embossed metal diaphragm has two-way stretch

Diaphragm with embossed pattern has greater structural rigidity than one with smooth surfaces, but under severe stress, tensile loads will flatten embossing. This provides necessary additional panel stretch needed to prevent rupture of diaphragm material. Hexagonal embossing-configuration allows panel stretch in any direction or in all directions simultaneously.

Macglashan, W. F., Jr.↗

NASA NTRS1973

Texturing in metals as a result of sliding

Sliding friction experiments were conducted with copper, nickel, iron, and cobalt sliding on themselves in air and argon. The resulting wear surfaces were examined with X-ray analysis to determine if surface texturing had occurred as a result of sliding. Results of the investigation indicate that, for the face-centered-cubic metals copper and nickel, a (111) texture develops with the (111) planes tilted 10 deg in the direction of sliding. The body-centered-cubic metal iron exhibited a (110) texture with the (100) direction oriented in the direction of sliding. It also exhibited a 10 deg tilt in the direction of sliding. The environment influenced the results in that the degree of texture observed in argon was less than that seen in air for iron. No texturing was observed for the close-packed-hexagonal metal cobalt. Recrystallization was observed with copper as a result of sliding.

Wheeler, D. R.↗

NASA NTRS1972

Development of lightweight graphite/polyimide sandwich panels.

Lightweight graphite/polyimide composite honeycomb core and sandwich panels were fabricated and tested. Honeycomb cores of 1/4-in. and 3/8-in. cell sizes of hexagonal configuration were produced from thin plus or minus 45 deg cross plied sheets of prepreg producing core weights between 1.8 and 3.6 lb/cu ft. Thin gauge prepreg using Hercules graphite tow and Monsanto Skybond 710 polyimide resin were manufactured to produce cured ply thicknesses of 0.001 to 0.002 in. Graphite core properties measured at temperatures from -150 to 600 F are reported. Core properties which are superior to available materials were obtained. Sandwich panels weighing less than 0.5 lb/sq ft were designed and fabricated which meet the support structure loads for the shuttle orbiter thermal protection system.

Poesch, J. G.↗

NASA NTRS1974

A low cost ""Air Mass 2'' solar simulator

Tungsten halogen projection lamps have integral ellipsoidal reflector, and hexagonal shaped plastic Fresnel lenses. Reflector is dichroic coated to reduce infrared content of reflected radiation. Array of lamps and lenses produces uniform collimated beam having near AM2 spectrum and intensity that can be used for testing flat plate solar collectors.

Yass, K.↗

NASA NTRS1974

Some injector element detail effects on screech in hydrogen-oxygen rockets

An experimental investigation was conducted to learn more about how the specific details of a concentric tube injection element affect the screech characteristics of a hydrogen-oxygen rocket engine. The four variables investigated were (1) impingement angle, (2) oxidizer tube blunt base thickness, (3) oxidizer tube recess and extension, and (4) oxidizer tube-annulus concentricity. Tests were made using a 27.34-cm (10.77-in.) diameter heat sink combustor at nominally 300-psia chamber pressure. All of the test variables were investigated using a 157 element circular pattern injector. Additional oxidizer tube recess tests were made with a 421 element hexagonal pattern injector. Tests were conducted over the oxidant-fuel ratio range of 4 to 6. Stability evaluation for each configuration was made using the hydrogen temperature rating technique. Several element configurations were also cold flow tested using nitrogen and water as simulants. The element detail changes resulted in changes in hydrogen injector pressure drop even though the physical injection area was constant for all similar tests in both hot firing and cold flow tests. These changes in injector pressure drop produced changes in combustion stability. The data were correlated with a modified version of a previously reported injection area ratio correlation. By interpreting changes in injector pressure drop as changes in injector hydrogen flow resistance, the data were compared with a hydrogen flow response stability model and were found to be in agreement.

Hannum, N. P.↗

NASA NTRS1974

Creep behavior of tantalum alloy T-222 at 1365 to 1700 K

High vacuum creep tests on the tantalum T-222 alloy at 0.42 to 0.52 T sub m show that the major portion of the creep curves, up to at least 1 percent strain, can be best described by an increasing creep rate, with strain varying linearly with time. Correlation and extrapolation of the creep curves on the basis of increasing creep rates results in more accurate engineering design data than would use of approximated linear rates. Based on increasing creep rates, the stress for 1 percent strain in 10,000 hours for T-222 is about four times greater than for the Ta-10W alloy. Increasing the grain size results in increased creep strength. Thermal aging prior to testing caused precipitation of the hexagonal close packed (Hf,Ta) sub 2 C, which initially increased creep strength. However, this dimetal carbide was converted during creep testing to face-centered cubic (Hf,Ta)C.

Titran, R. H.↗

NASA NTRS1974

Low-cost, air mass 2 solar simulator

A low cost air mass 2 solar simulator for testing flat-plate solar collectors was developed and operated at Lewis. Total cost was less than $10,800/sq m ($1000/sq ft). It consists of an array of 143 tungsten-halogen 300-watt lamps, each having integral dichroic coated reflectors. A second array of 143 respective hexagonal-shaped plastic Fresnel lenses are located approximately 1 focal length from the lamps. The simulator will produce a uniform collimated beam covering an area of 1.2 by 1.2m(4 by 4 ft). Design features, construction details, and component costs are given, as well as measured results on a 12-lamp prototype.

Yass, K.↗

NASA NTRS1974

Tough cryogenic alloys from the Fe-Mn and Fe-Mn-Cr systems

By adjusting composition, metastable gamma (austenite) and epsilon (hexagonal) martensite may be retained in Fe-Mn and Fe-Mn-Cr alloys and used to impact toughness through the TRIP mechanism. The resulting alloys have excellent toughness at cryogenic temperatures. The best alloys obtained to date are: Fe-20Mn, with sigma (sub y) = 79ksi and K sub IC = 275ksi square root of (in) at 77 K, and Fc-16Mn-8Cr, with sigma sub y = 85ksi and K sub IC = 72ksi square root of (in) at 77 K.

Schanfein, M. J.↗

NASA NTRS1975

Operational performance of a low cost, air mass 2 solar simulator

Modifications and improvements on a low cost air mass 2 solar simulator are discussed. The performance characteristics of total irradiance, uniformity of irradiance, spectral distribution, and beam subtense angle are presented. The simulator consists of an array of tungsten halogen lamps hexagonally spaced in a plane. A corresponding array of plastic Fresnel lenses shapes the output beam such that the simulator irradiates a 1.2 m by 1.2 m area with uniform collimated irradiance. Details are given concerning individual lamp output measurements and placement of the lamps. Originally, only the direct component of solar irradiance was simulated. Since the diffuse component may affect the performance of some collectors, the capability to simulate it is being added. An approach to this diffuse addition is discussed.

Yass, K.↗

NASA NTRS1975

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗

NASA NTRS1975

Analysis and trade-off studies of large lightweight mirror structures

A candidate mirror, hexagonally lightweighted, is analyzed under various loadings using as complete a procedure as possible. Successive simplifications are introduced and compared to an original analysis. A model which is a reasonable compromise between accuracy and cost is found and is used for making trade-off studies of the various structural parameters of the lightweighted mirror.

Soosaar, K.↗

NASA NTRS1974

Effect of various material properties on the adhesive stage of fretting

Buckley, D. H.↗

NASA NTRS1975

Texturing in metals as a result of sliding

Sliding friction experiments were conducted with copper, nickel, iron and cobalt sliding on themselves in air and argon. The resulting wear surfaces were examined by X-ray analysis to determine if surface texturing had occurred as a result of sliding. Results of the investigation indicate that, for the face-centered-cubic metals copper and nickel, a (111) texture develops with the (111) planes tilted 10 deg in the direction of sliding. The body-centered-cubic metal iron exhibited a (110) texture with the (111) direction oriented in the direction of sliding. It also exhibited a 10 deg tilt in the direction of sliding. The environment influenced the results in that the degree of texture observed in argon was less than that seen in air for iron. No texturing was observed for the close-packed-hexagonal metal cobalt. Recrystallization was observed with copper as a result of sliding.

Wheeler, D. R.↗

NASA NTRS1976

Flexible fitting for fluid lines

Tube fitting, consisting of movable tubular section containing two spring pressure Teflon actuated low friction seals, two standard connectors, and two hexagonal retaining nuts, provides flexible joint that allows axial and rotational motion.

Barajas, S. L.↗

NASA NTRS1976

Investigations of electromagnetic scattering by columnar ice crystals

An integral equation approach was developed to determine the scattering and absorption of electromagnetic radiation by thin walled cylinders of arbitrary cross-section and refractive index. Based on this method, extensive numerical data was presented at infrared wavelengths for hollow hexagonal cross section cylinders which simulate columnar sheath ice crystals.

Weil, H.↗

NASA NTRS1975

Demonstration of the feasibility of automated silicon solar cell fabrication

A study effort was undertaken to determine the process, steps and design requirements of an automated silicon solar cell production facility. Identification of the key process steps was made and a laboratory model was conceptually designed to demonstrate the feasibility of automating the silicon solar cell fabrication process. A detailed laboratory model was designed to demonstrate those functions most critical to the question of solar cell fabrication process automating feasibility. The study and conceptual design have established the technical feasibility of automating the solar cell manufacturing process to produce low cost solar cells with improved performance. Estimates predict an automated process throughput of 21,973 kilograms of silicon a year on a three shift 49-week basis, producing 4,747,000 hexagonal cells (38mm/side), a total of 3,373 kilowatts at an estimated manufacturing cost of $0.866 per cell or $1.22 per watt.

Taylor, W. E.↗