SEARCH · Search NASA

Results for “high cathode loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Realizing high-capacity all-solid-state lithium-sulfur batteries using a low-density inorganic solid-state electrolyte

Abstract Lithium-sulfur all-solid-state batteries using inorganic solid-state electrolytes are considered promising electrochemical energy storage technologies. However, developing positive electrodes with high sulfur content, adequate sulfur utilization, and high mass loading is challenging. Here, to address these concerns, we propose using a liquid-phase-synthesized Li 3 PS 4 -2LiBH 4 glass-ceramic solid electrolyte with a low density (1.491 g cm −3 ), small primary particle size (~500 nm) and bulk ionic conductivity of 6.0 mS cm −1 at 25 °C for fabricating lithium-sulfur all-solid-state batteries. When tested in a Swagelok cell configuration with a Li-In negative electrode and a 60 wt% S positive electrode applying an average stack pressure of ~55 MPa, the all-solid-state battery delivered a high discharge capacity of about 1144.6 mAh g −1 at 167.5 mA g −1 and 60 °C. We further demonstrate that the use of the low-density solid electrolyte increases the electrolyte volume ratio in the cathode, reduces inactive bulky sulfur, and improves the content uniformity of the sulfur-based positive electrode, thus providing sufficient ion conduction pathways for battery performance improvement.

25 ENERGY STORAGE↗

DOE OSTI2021

Interpreting Ionic Conductivity for Polymer Electrolyte Fuel Cell Catalyst Layers with Electrochemical Impedance Spectroscopy and Transmission Line Modeling

A cathode catalyst layer containing optimally distributed ionomer is critical to reduce the platinum loading and increase its utilization in polymer electrolyte fuel cells. Here, electrochemical impedance spectroscopy (EIS) was used to measure effective ionic conductivity of pseudo catalyst layers (PCLs) at a relative humidity (RH) range of 50%-120%. These results are compared to previous work using the hydrogen pump (HP) method. EIS effective ionic conductivity results reported here are higher than those from the HP because in the HP set-up ionic pathways must be effectively connected through the PCL to be counted, whereas in the EIS measurement, ionomer segments that are in contact with the membrane but are not effectively connected all the way through the PCL can be detected. Double layer capacitances and effective ionic conductivities of Pt/C catalyst layers with various supports and ionomer to carbon (I/C) ratios were studied. High surface area carbon support resulted in a lower effective ionic conductivity compared to the graphitized carbon support due to worse ionomer dispersion. Effective ionic conductivities of Pt/C layers were compared to that of PCLs. On average, effective ionic conductivities of Pt/C layers were higher than PCLs because of possible carbon agglomeratio n within the PCLs.

25 ENERGY STORAGE↗

DOE OSTI2021

Nanotechnology for Sulfur Cathodes

The field of lithium-sulfur batteries has benefited enormously from the advances in nanotechnology. At each step of technological improvement, lithium-sulfur batteries have relied upon techniques and methodologies brought upon by nanotechnology. Nanoporous material, heterogeneous nanocomposite, and hierarchical electrode developments have all been well-established as critical milestones for lithium-sulfur batteries. Overall, this review will briefly discuss the specific major roles of nanotechnology in lithium-sulfur batteries regarding practically relevant testing conditions in addition to research trends and future directions for electrocatalysis.

25 ENERGY STORAGE↗

DOE OSTI2021

Enhanced Performance of Pt Nanoparticles on Ni-N Co-Doped Graphitized Carbon for Oxygen Reduction Reaction in Polymer Electrolyte Membrane Fuel Cells

Since the reaction rate and cost for cathodic catalyst in polymer electrolyte membrane fuel cells are obstacles for commercialization, the high-performance catalyst for oxygen reduction reaction is necessary. The Ni encapsulated with N-doped graphitic carbon (Ni@NGC) prepared with ethylenediamine and carbon black is employed as an efficient support for the oxygen reduction reaction. Characterizations show that the Ni@NGC has a large surface area and mesoporous structure that is suitable to the support for the Pt catalyst. The catalyst structure is identified and the size of Pt nanoparticles distributed in the narrow range of 2–3 nm. Four different nitrogen species are doped properly into graphitic carbon structure. The Pt/Ni@NGC shows higher performance than the commercial Pt/C catalyst in an acidic electrolyte. The mass activity of the Pt/Ni@NGC in fuel cell tests exhibits over 1.5 times higher than that of commercial Pt/C catalyst. The Pt/Ni@NGC catalyst at low Pt loading exhibits 47% higher maximum power density than the Pt/C catalyst under H2-air atmosphere. These results indicate that the Ni@NGC as a support is significantly beneficial to improving activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Development of high-energy non-aqueous lithium-sulfur batteries via redox-active interlayer strategy

Abstract Lithium-sulfur batteries have theoretical specific energy higher than state-of-the-art lithium-ion batteries. However, from a practical perspective, these batteries exhibit poor cycle life and low energy content owing to the polysulfides shuttling during cycling. To tackle these issues, researchers proposed the use of redox-inactive protective layers between the sulfur-containing cathode and lithium metal anode. However, these interlayers provide additional weight to the cell, thus, decreasing the practical specific energy. Here, we report the development and testing of redox-active interlayers consisting of sulfur-impregnated polar ordered mesoporous silica. Differently from redox-inactive interlayers, these redox-active interlayers enable the electrochemical reactivation of the soluble polysulfides, protect the lithium metal electrode from detrimental reactions via silica-polysulfide polar-polar interactions and increase the cell capacity. Indeed, when tested in a non-aqueous Li-S coin cell configuration, the use of the interlayer enables an initial discharge capacity of about 8.5 mAh cm −2 (for a total sulfur mass loading of 10 mg cm −2 ) and a discharge capacity retention of about 64 % after 700 cycles at 335 mA g −1 and 25 °C.

25 ENERGY STORAGE↗

DOE OSTI2024

Synthetic methods for crystallite size control of bimetallic polyanionic battery compositions

Bimetallic polyanionic materials, such as silver vanadium phosphorus oxide (Ag 2 VO 2 PO 4 , SVOP), are promising cathode materials for Li batteries due in part to their large capacity and high current capability. A new synthesis of Ag 2 VO 2 PO 4 based on microwave heating is disclosed, where the reaction time is reduced by approximately 100 times relative to other reported methods, and the crystallite size is controlled via synthesis temperature, showing a linear positive correlation of crystallite size with temperature. Reaction times of an hour or less are sufficient to render phase-pure material after reaction at 50° C. to 180° C., significantly lower than the temperatures reported for other methods. Crystallite sizes between 42 nm and 60 nm are achieved by the novel method, smaller than by other methods. Silver/vanadium atomic ratios of 1.96 to 2.04 in the as-synthesized SVOP result and appear temperature-dependent. Notably, under galvanostatic reduction, the Ag 2 VO 2 PO 4 sample with the smallest crystallite size delivers the highest capacity and shows the highest loaded voltage.

Takeuchi, Kenneth J.↗

DOE OSTI2021

Influence of Surface and Structural Variations in Donor–Acceptor–Donor Sensitizers on Photoelectrocatalytic Water Splitting

Conjugated organic chromophores composed of linked donor (D) and acceptor (A) moieties have attracted considerable attention for photoelectrochemical applications. In this work, we compare the optoelectronic properties and photoelectrochemical performance of two D–A–D structural isomers with thiophene-X-carboxylic acid (X denotes 3 and 2 positions) derivatives and 2,1,3-benzothiadiazole as the D and A moieties, respectively. 5,5′-(Benzo[c][1,2,5]thiadiazole-4,7-diyl)bis(thiophene-3-carboxylic acid), BTD1, and 5,5′-(benzo[c][1,2,5]thiadiazole-4,7-diyl)bis(thiophene-2-carboxylic acid), BTD2, were employed in the study to understand how structural isomers affect surface attachments within chromophore–catalyst assemblies and their influence on charge-transfer dynamics. Crystal structures revealed that varying the position of the −COOH anchoring group causes the molecules to either contort out of a plane (BTD1) or adopt a near-perfect planar conformation (BTD2). BTD1 and BTD2 were co-loaded with either a water oxidation catalyst, [Ru(2,6-bis(1-methylbenzimidazol-2-yl)pyridine)-(4,4′-((HO) 2 OPCH 2 )2-2,2′-bipyridine)(OH 2 )] 2 , RuCt 2+ , or proton reduction catalyst [Ni(P 2 Ph N 2 C 6 H 4 CH 2 PO 3 H 2 ) 2 ] 2+ , NiCt 2+ , on oxide electrodes to facilitate photodriven water splitting reactions. Emission quenching measurements indicate that both BTD1 and BTD2 inject electrons into n-type SnO 2 |TiO 2 electrodes and holes into p-type NiO semiconductors from their respective excited states at high efficiencies >60%. Photocurrent densities of chromophore–catalyst assemblies obtained using linear sweep voltammetry (LSV) show that BTD2-sensitized photoanodes generate significantly more photocurrent than BTD1-sensitized electrodes; however, both exhibit similar performances at the photocathode. Photoelectrocatyltic measurements demonstrate that both BTD1 and BTD2 performed similarly, generating Faradaic efficiencies of 39 and 38% at the anode or 61 and 79% at the cathode. Transient absorption measurements suggest that the differences between the LSV and photoelectrocatalytic measurements result from the differences in quantum yields of the photogenerated redox equivalents, which is also a reflection of the varying metal oxide surface conformation. Our findings suggest that BTD2 should be investigated further in photocathodic studies since it has the structural advantage of being incorporated into diverse types of chromophore–catalyst assemblies.

Chromophores↗

DOE OSTI2024

Understanding the impact of an applied axial magnetic field on efficient current coupling on the Z machine

Magnetized liner inertial fusion (MagLIF) is an attractive concept for producing thermonuclear fusion reactions. The MagLIF platform involves the operation of Helmholtz coils to apply a 15 Tesla axial magnetic field to the load region, where a cylindrical, fuel-filled metal liner is imploded by a ∼ 2 0 MA current pulse. The fringe field from these coils extends into the transmission line that delivers the current to the target. We investigated the extent to which this applied field disturbs the nominal power flow within that transmission line. A simplified model of the geometry shows that adding the applied magnetic field results in magnetic field lines that connect the cathode to the anode, suggesting electrons may not be magnetically insulated in this region. Particle-in-cell simulations indicated the addition of the applied magnetic field would not significantly impact the current delivery to the load. Velocimetry was used to experimentally assess the current delivery with and without the applied magnetic field. We find no measurable effects of the applied field on current delivery in the configuration investigated in this study. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Additively manufactured electrodes for plasma and power-flow studies in high-power transmission lines on the 1-MA MAIZE facility

Power-flow studies on the 30-MA, 100-ns Z facility at Sandia National Laboratories have shown that plasmas in the facility’s magnetically insulated transmission lines (MITLs) and double post-hole convolute can result in a loss of current delivered to the load. To study power-flow physics on the 1-MA, 100-ns MAIZE facility at the University of Michigan, planar MITL loads and planar post-hole convolute loads have been developed that extend into the lines of sight for various imaging diagnostics on MAIZE. These loads use 3D-printed dielectric support structures lined with thin foils of either aluminum or stainless steel. Here, the metal foils serve as the current-carrying power-flow surfaces, which generate plasma during the current pulse. The foil thickness (50 µm) and widths (11.5–16 mm) are selected to ensure a sufficient linear current density (0.5–0.7 MA/cm) for plasma formation. Laser backlighting (532 nm) and visible-light self-emission imaging capture the overall plasma evolution in the anode–cathode gaps, including the gap closure velocities (1–4 cm/μs).

47 OTHER INSTRUMENTATION↗

DOE OSTI2026

Deciphering the Conflict Between Ion and Electron Percolating Networks in Solid-State Battery Cathodes

High-energy- and power-density solid state batteries require an optimal cathode composition and microstructural arrangement of cathode active material, solid-state electrolyte, conductive carbon, and binder to simultaneously support lithium-ion transport, electron conduction, and storage capacity. The ion and electron conducting phases in solid-state cathodes counteract each other's percolating networks as their mass ratios increase or decrease relative to each other. Here, we investigate targeted mass ratio variations of argyrodite solid electrolyte and two different types of conductive carbon (particles and fibers) in composite LiNi0.8Mn0.1Co0.1O2 (NMC811) solid-state cathodes to ascertain the ionic-electronic tradeoffs in cathode performance. Through ionic and electronic conductivity measurements on composite cathodes, as well as rate-testing and cycling performance in full cells, it is shown that the conductive carbon fibers form a percolative electronic network within the composite at a lower mass ratio (3-5 wt%) than particulate carbon (>5 wt%). The threshold to achieve electronic percolation coincides with higher accessible capacity in the cathode as the active material particles become electronically connected. However, carbon loadings beyond this percolation threshold lead to increased ion transport resistance, arising from disruptions to ionic conduction pathways and degraded contact at the interface between the electrolyte and active materials. Imaging, spectroscopy, and physics-based models quantitatively describe the relationship between carbon and electrolyte compositions and the cell's capacity and rate performance through percolation theory. This work demonstrates the importance of quantitatively understanding percolating networks in solid-state cells and that strategic engineering of conductive carbon morphologies can further increase the energy- and power-density of solid-state cells.

25 ENERGY STORAGE↗

DOE OSTI2021

A Nickel-Decorated Carbon Flower/Sulfur Cathode for Lean-Electrolyte Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries involve a reversible conversion reaction between sulfur and lithium sulfide (Li 2 S) via a series of soluble lithium polysulfide intermediates (LiPSs), enabling a high theoretical specific capacity of 1675 mAh g –1 . However, this process exhibits large polarization and low sulfur utilization and suffers critical capacity fade. The primary approach to tackle the problem has so far been to infiltrate sulfur into nanostructured carbon. Furthermore, most studies using porous carbon as host materials have tested with high electrolyte to sulfur ratios (E/S) (generally > 15 µL mg –1 ) that compromise the cell-level energy density. Here, a flower-shaped porous carbon structure with nickel nanoparticles that can address the problems discussed above is designed. First, the 3D flower-shaped carbon structure enables short ionic transport lengths. Second, the small pore diameters <10 nm and high specific surface areas > 3300 m 2 g –1 with sufficient pore volume are ideal for charging performance for low E/S ratios. Finally, Ni nanoparticles are employed onto the flower-shaped network to improve the reaction kinetics. Collectively, it is successfully demonstrated that the batteries with a high mass loading of 5 mg cm –2 and a 5 µL mg –1 E/S ratio can retain cycle retention of 70% after 150 cycles.

25 ENERGY STORAGE↗

DOE OSTI2024

Image-Based Digital Twin for Assessing the Coupled Electro-Chemo-Mechanical Behavior of Li-Ion Batteries

In energy storage materials, strong electrochemical-mechanical coupling and highly anisotropic material properties contribute to the formation and propagation of micro-cracking during charge/discharge cycling, resulting in reduced performance and service life. In this work, a digital twin is created to investigate the performance of a Li-ion battery cathode and simulate degradation accumulation. Pixel-based model construction is used to represent the complex material geometries from microstructural images supplied by the National Renewable Energy Laboratory (NREL). Because of the expected large deformation and crack opening, the reproducing kernel particle method (RKPM), a meshfree method with discretization at the image pixels, is used to approximate the field variables: electrostatic potential, concentration, and displacement. An interface modified reproducing kernel (IM-RK) is constructed by scaling a smooth kernel function with an interface-distance function to achieve strategic discontinuity types (i.e. weak discontinuities for strain discontinuities and strong discontinuities for cracks) and alleviate Gibbs oscillations near these transition zones. The discrete nature of the images' pixel points is employed throughout the model and approximation construction. The mechanical model is verified using an image-based microstructure under tensile loading. A transient electro-chemo-mechanical coupled simulation is performed to evaluate the potential micro-cracking induced degradation of the battery cathode material subjected to charge/discharge cycling.

battery degradation↗

DOE OSTI2020

Novel Ionomers and electrode structures for improved PEMFC electrode performance at low PGM loadings (Final Report)

In this project, the objective is to develop new ORR electrocatalysts on optimized supports which can exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001412 directly relevant to the subtopic. This project’s approach is to develop novel, electrode-specific ionomers, and integrate them with state-of-the-art NSTF electrocatalyst powder to develop a cathode electrode achieving >= 044 A/mg PGM mass activity, <=30% mass activity loss during metal cycling, and <=0.125 g PGM /kW performance under DOE testing protocols. Ionomer O 2 permeability and proton conductivity will be increased by up to 1.5X over the baseline 3M800 perfluorosulfonate (PFSA) ionomer to enhance cathode electrode performance. Integration of cathode NSTF powder into an ionomer-containing electrode will increase the surface enhancement factor (SEF) to >=40 cm 2 PGM /cm 2 GEO allowing NSTF containing cathodes to exceed DOE MEA robustness targets. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of significant findings, conclusions, and developments over the entire project period from Oct. 1 st 2016 – Jan. 31 st 2020. This work has overcome key operation robustness issues with classic NSTF electrodes, identified pathways to improved dispersed and dispersed NSTF cathode performance, developed novel ionomers with high bulk conductivity and oxygen permeability, demonstrated exceptional support-independent electrode activity, and significantly increased metal and support stability through ionomer development. At this point, Tufts, MTU and all 5 FCPAD national labs have been involved, and contributed to, the improvements, learning and achievements of this work. Over the course of this project, more than 50 grams of dispersed NSTF powder in 15 different configurations have been generated, paving the way for scaleup within 3M. These whiskers have been processed in multiple ways, including acid leaching, powder-annealed, and sonicated by various means. For Task 2, 27 different types of ionomers were tested, 19 of which were made for the first time during the course of this project. 377 electrode inks with both NSTF and metal-on-carbon catalysts with I/C ratios from 0.2 to 1.2 were generated and mostly coated on a 3M pilot manufacturing line resulting in more than 700 different electrode types.

08 HYDROGEN↗

DOE OSTI2020

Characterization of Self-Magnetic Pinch (SMP) Radiographic Diode Performance on RITS-6 at Sandia National Laboratories

The goals of an electron beam-driven radiographic source are the focusing of high current at high voltage to a minimal spot size with excellent shot-to-shot reproducibility. The Self-Magnetic Pinch (SMP) diode makes use of such an intense electron beam impinging on a high-atomic weight (tantalum) converter, a counter-streaming ion beam to help minimize the spot size, and operation in a magnetic field-free diode region which further encourages small spot size. Through a series of diode development experiments, output voltages up to 12.5 MV and output currents up to 225 kA have been characterized, with resulting spot sizes below ~ few mm. Scaling studies with parameter variation, such as diode aspect ratio and anode-cathode (A-K) gap variation, give systematic validation to what has heretofore been noted anecdotally by other research groups. While the lack of an imbedded magnetic field helps minimize the SMP spot size, a secondary result may be the generation of beam instabilities which can terminate the radiation pulse. There is anecdotal evidence that in-situ DC heating of the diode region can help stabilize the beam pinch. Clear experimental evidence exists that DC heating/RF cleaning results in better control over the counter-streaming ion population. Expanded use of spatial dose-rate detection is shown to yield new insights into electron beam dynamics in the SMP diode. An attendant study of the SMP diode as a load for an Inductive Voltage Adder (IVA) driver leads to insights into the behavior of the IVA-SMP diode configuration, viewed as a total system, and yields constraints on the overall impedance behavior of the SMP diode load.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Excessive charge, beam loading, and impedance collapse thresholds for a velvet emitter

Excess emission has been observed from velvet cathodes with total emission times >150 ns. In this diode experiment, we produce a sub-relativistic electron beam with the ability to consistently change γ from 1.2 to 1.5 and β = 0.5–0.75. Electron emission in this particular diode geometry requires electric fields >40 kV/cm. The current increases at steady rates >0.05 A/ns after the head of the pulse, indicating an expansion of the emission surface and reduction in the effective AK gap. Small transients of excess emission (or arcs) are consistently observed for current pulses exceeding 150 ns. The excess emission results in beam loaded levels ≥10 kV on the diode voltage. The effects described here are compounded as diode voltage is increased. The principal objective of these experiments is to quantify electric field emission thresholds, current ramps, excess emission delays, effective beam loading, and impedance collapse.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Highly durable platinum group metal-free catalyst fiber cathode MEAs for proton exchange membrane fuel cells

For this work, Fe-based platinum group metal (PGM)-free catalysts were incorporated into electrospun fiber mat or powder cathode membrane-electrode-assemblies (MEAs) with a Nafion 211 membrane and a Pt/C powder anode. Fabrication and characterization tests were performed on MEAs with: (1) a conventional powder cathode with a neat Nafion binder, (2) a fiber mat cathode with a Nafion/polyethylene oxide (PEO) binder, where PEO was extracted before MEA testing, (3) a powder cathode with a blended binder of Nafion and polyvinylidene fluoride (PVDF), and (4) a series of fiber mat cathodes with different Nafion/PVDF binder weight ratios. Cathode degradation occurred, with a loss in power output, in MEAs with a neat Nafion powder cathode or with a Nafion fiber cathode. In contrast, little or no power loss was observed for powder or fiber cathodes when the binder was a blend of Nafion and PVDF. The presence of hydrophobic PVDF drove water and electrogenerated peroxide out of the cathode, away from catalyst particles, which improved cathode durability, but PVDF also decreased the binder conductivity and slowed oxygen reduction kinetics, resulting in lower power densities. A 75:25 w:w Nafion:PVDF fiber cathode MEA was the best compromise for maximizing power and minimizing catalyst degradation. For such a cathode, with a PGM-free cathode catalyst loading of 3.0 mg cm –2 , a power density of 88 mW cm –2 at 0.5 V, 80 °C, and 200 kPa abs pressure was maintained for 80 h of continuous operation.

25 ENERGY STORAGE↗

DOE OSTI2020

Reversible Crosslinked Polymer Binder for Recyclable Lithium Sulfur Batteries with High Performance

Owing to the negative impact of the extensive utilization of batteries on the environment, sustainability of the cells needs to be included in the systemic research of batteries. In this work, a dissolvable ionic crosslinked polymer (DICP) is exploited as a binder for lithium–sulfur batteries by crosslinking the polyacrylic acid and polyethyleneimine through carboxy-amino ionic interaction. This interaction is pH-controlled, and therefore, the crosslinked binder network can be readily dissociated under basic conditions, providing a facile strategy enabling valuable components recycled through a convenient washing method. The sulfur cathode prepared using the recycled carbon–sulfur composite can deliver comparable capacity as that of fresh electrode. In addition, evidence from cell performance and characterizations, such as in situ X-ray absorption spectroscopy, in situ UV–visible spectroscopy, X-ray photoelectron spectroscopy, and density functional theory calculation, confirms that DICP is a more effective binder than its commercial counterpart on suppressing polysulfide dissolution in the electrolyte. Exploiting reversible crosslinked polymer binder for recyclable Li–S batteries with ameliorated electrochemical performance, this study illuminates sustainable development for large-scale energy storage systems.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗