NASA high temperature loads calibration laboratory
Design and operation of high temperature loads calibration laboratory
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design and operation of high temperature loads calibration laboratory
High purity single crystal titanium (Ti) under shock wave loading is modeled under both one-dimensional and three-dimensional cylindrical conditions. Cylinder sizes of 10 μm and 20 μm radius are both considered in order to assess influence of boundary conditions. A thermodynamically consistent single crystal model for application to shock conditions is presented. The model accounts for the coupled non-linear elastic, dislocation slip, deformation twinning, and structural phase transformation response of the titanium material. Plate impact experiment results using a copper flyer are used to compare against the simulations for crystals oriented in [0001] and [10$\overline1$1] crystallographic directions. The one-dimensional and threedimensional simulations of the two differently oriented single crystals indicate differences between the one-dimensional and three-dimensional representation, especially for the [10$\overline1$1] oriented single crystal. This orientation breaks the relative orientation symmetry between the crystal and cylinder which otherwise exists for the [0001] oriented single crystal. A significant amount of heterogeneity in the field response of the[10$\overline1$1] oriented simulation was demonstrated due to the highly coupled nature of the deformation. A bi-crystal model composed of both the [0001] and [10$\overline1$1] orientations with the boundary between the two along the axis of the cylinder is also considered for a cylinder model size of 10 μm. The results indicate a strong interaction between the two grains that affects the ω phase volume fraction achieved relative to the single crystal calculations.
X-ray diffraction was used to measure the unit cell parameters of B-ZSM-5, SAPO-34, and NaA zeolite powders as a function of adsorbate loading at 303 K, and in one case, at elevated temperatures. Most adsorbates expanded the zeolite crystals below saturation loading at 303 K: n-hexane and SF6 in B-ZSM-5, methanol and CO2 in SAPO-34, and methanol in NaA zeolite. As the loadings increased, the crystals expanded more. Changes in the unit cell volumes of B-ZSM-5 and SAPO-34 zeolite powders correlated with changes in permeation through zeolite membranes defects. When the zeolite crystals expanded or contracted upon adsorption, the defect sizes decreased or increased. In B-ZSM-5 membranes, the fluxes through defects decreased dramatically when n-hexane or SF6 adsorbed. In contrast, i-butane adsorption at 303 K contracted B-ZSM-5 crystals at low loadings and expanded them at higher loadings. Correspondingly, the flux through B-ZSM-5 membrane defects increased at low i-butane loadings and decreased at high loading because the defects increased in size at low loading and decreased at high loadings. At 398 K and 473 K, n-hexane expanded the B-ZSM-5 unit cell more as the temperature increased from 303 to 473 K. The silicalite-1 and B-ZSM-5 unit cell volumes expanded similarly upon n-hexane adsorption at 303 K; boron substitution had little effect on volume expansion.
Fabrication and results of high-resolution X-ray topography characterization of diamond single-crystal plates with large surface area (10 mm × 10 mm) and (111) crystal surface orientation for applications in high-heat-load X-ray crystal optics are reported. The plates were fabricated by laser-cutting of the (111) facets of diamond crystals grown using high-pressure high-temperature methods. The intrinsic crystal quality of a selected 3 mm × 7 mm crystal region of one of the studied samples was found to be suitable for applications in wavefront-preserving high-heat-load crystal optics. Wavefront characterization was performed using sequential X-ray diffraction topography in the pseudo plane wave configuration and data analysis using rocking-curve topography. In conclusion, the variations of the rocking-curve width and peak position measured with a spatial resolution of 13 µm × 13 µm over the selected region were found to be less than 1 µrad.
Abstract The increasing electrification of daily life as well as the intermittent characteristic of renewable energy sources require viable solutions for grid‐scale energy storage. Critical considerations for grid storage applications are electrode mass loading and electrode thickness as these features govern battery pack energy density, an important factor in determining manufacturing costs. For this reason, there is increased interest in finding new ways of creating electrodes with high mass loading. In this review, various high‐mass loading fabrication approaches are considered for positive electrode materials used in batteries. The benchmark used for high mass loading is above 20 mg cm −2 , which is higher than the practical limit of conventional tape‐cast electrodes. Several different electrode approaches are described including templating, laser patterning, direct ink writing, and electrodeposition. A variety of materials are covered with the most prominent being LiFe(PO 4 ) (LFP), LiCoO 2 (LCO), and MnO 2 . In research to date, scalable electrochemical performance has been achieved with mass loadings over 100 mg cm −2 . Areal capacities as high as 14.7 mAh cm −2 at 1.82 mA cm −2 have been achieved in non‐aqueous electrolytes and 9.8 mAh cm −2 at 10 mA cm −2 in aqueous electrolytes. These results establish that the mass loading of electrodes can be scaled up without compromising their electrochemical properties.
Abstract Ignition delay times were measured for methane/O2 mixtures in a high dilution environment of either CO2 or N2 using a shock tube facility. Experiments were performed between 1044 K and 1356 K at pressures near 16 ± 2 atm. Test mixtures had an equivalence ratio of 1.0 with 16.67% CH4, 33.33% O2, and 50% diluent. Ignition delay times were measured using OH* emission and pressure time-histories. Data were compared to the predictions of two literature kinetic mechanisms (ARAMCO MECH 2.0 and GRI Mech 3.0). Most experiments showed inhomogeneous (mild) ignition which was deduced from five time-of-arrival pressure transducers placed along the driven section of the shock tube. Further analysis included determination of blast wave velocities and locations away from the end wall of initial detonations. Blast velocities were 60–80% of CJ-Detonation calculations. A narrow high temperature region within the range was identified as showing homogenous (strong) ignition which showed generally good agreement with model predictions. Model comparisons with mild ignition cases should not be used to further refine kinetic mechanisms, though at these conditions, insight was gained into various ignition behavior. To the best of our knowledge, we present first shock tube data during ignition of high fuel loading CH4/O2 mixtures diluted with CO2 and N2.
Increased focus on carbon neutral energy has generated a resurgence of interest in nuclear power, and in particular advanced reactors which are likely to utilize high assay low enriched uranium (HALEU). This in turn could increase the economic attractiveness of recovering still partially enriched uranium from used nuclear fuel. Concomitant to development of advanced reactors, advanced reprocessing schemes should be developed which address the disadvantages to well established reprocessing schemes. The present study focuses on using di-(2-ethylhexyl)-iso-butyramide (DEHiBA) under high metal loading conditions for the reprocessing of used nuclear fuel. The elements examined in the study include the dominant transuranic actinides (Np, Pu, Am) as well as the often-problematic Tc and Zr. Further, by increasing the concentration of the extractant from the more commonly reported 1.0 M – 1.5 M, the extraction of hexavalent actinides is substantially increased, while maintaining effective rejection of tri, tetra, and pentavalent actinides, particularly in the presence of high loadings of uranium. In conclusion, the extraction of Zr by 1.5 M DEHiBA is noted to be negligible by comparison to tributyl phosphate (TBP), however the coextraction of Tc with U is observed to be nominally twice the quantity that is extracted by TBP indicating a need for effective Tc management.
High-loading sulfur electrode is critical for high energy Lithium-sulfur (Li-S) batteries used for practical applications. Unfortunately, dense and high-loading sulfur electrodes usually suffer from low sulfur utilization rate and limited cycle life. In this work, effects of electrode porosity on the electrode energy density, cell cycling stability, Li anode interface, and electrolyte/sulfur ratio were systematically investigated using high loading sulfur electrodes. The reduced electrode porosity increases volumetric energy density but also hinders electrode wetting process. To solve this problem, polysulfide (Li2S6) is selected as an electrolyte additive to enhance electrolyte penetration into dense sulfur cathodes. As a result, a high energy density of 1300 Wh L-1 (at electrode level) has been obtained for a dense sulfur cathode with a sulfur loading of 4 mg cm-2 at a compressed thickness of 60 µm. Li-S batteries with dense electrodes and Li2S6 additive also demonstrate promising cycling stability (~80 % capacity retention for 200 cycles). These significant improvements are contributed by synergistic effects of the dense sulfur cathode, improved electrolyte penetration, and suppressed growth of passivation layer on Li metal anode. This study sheds light on rational sulfur cathode structure design as well as control of electrode porosity for balanced energy density and cycling life.
The present work investigates relations between fuel Reid vapor pressure (RVP) and biofuel (ethanol) content on stochastic preignition (SPI) at both sustained steady-state engine operation and following load transients. This work stems from in-field observations that automotive original equipment manufacturers have observed consistent seasonal increases in United States customer drivability complaints and warranty claims during September and October where SPI is suspected to be responsible. The seasonal timing of these events coincides with the United States seasonal fuel property changeover initiating on September 15 each year, where fuel RVP increases. To explore potential linkage between fuel RVP and SPI the present study employs engine SPI experiments coupled with laboratory spray measurements of fuels with RVPs of 8, 12, and 16 psi in both E10 (10% ethanol) and E25 (25% ethanol) fuels. Engine results are partitioned into fuel RVP and ethanol content effects on SPI in steady-state, sustained high-load engine operation and unsteady-state low- to high-load transitions, where off-engine spray vessel patternation and tip penetration results help to elucidate the observed fuel effects on SPI. A boosted direct-injected, spark-ignition engine was fueled with three market relevant E10 and E25 fuels with RVPs of 8, 12, and 16 to characterize the interplay between winter fuels and abnormal combustion behavior. The steady-state work shows that for high-load, steady-state engine operation, SPI is directly linked to fuel retention, which was found to be dependent on fuel distillation. The unsteady-state engine operation work shows that following low-to high-load transitions, SPI can occur from a memory of fuel property effects at low-load operation. Specifically, the fuel RVP effect on fuel spray collapse at low loads was found to correlate with SPI with a more than 95% confidence interval following low- to high-engine-load transitions. Results suggest that fuel-wall impingement at low-load operation could carry over into high-load transitions and generate SPI events following low- to high-load transitions.
An investigation was made in the Cleveland Altitude wind tunnel to determine the performance of an Aeroproducts H20C-162-X11M2 four-blade propeller on a YP-47M airplane at high blade loadings and high engine powers. The propeller characteristics were obtained for a range of power coefficients from 0.30 to 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements are indicative only of trends in propeller efficiency with changes in power coefficient and advance-diameter ratio because unknown interference effects existed during the investigation. At a free-stream Mach number of 0.40, the envelopes of the efficiency curves decreased about 11% between advance-diameter ratios of 2.40 and 4.40. An increase in power coefficient from 0.30 to 0.80 at an advance-diameter ratio of 2.40 had little effect on the propeller efficiency. A change in power coefficient from 0.40 to 1.00 at an advance-diameter ratio of 4.40 increased the propeller efficiency by about 40%. For conditions below the stall the thrust loading on the outboard blade sections increased more rapidly than on the inboard sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall, the thrust loading decreased on the outboard sections and increased on the inboard sections.
Practical lithium-sulfur batteries require high sulfur electrode loading and lean electrolyte designs, which entail more research efforts on the two cell-design parameters - sulfur loading and electrolyte/sulfur loading ratio (E/S). In this work, a systematic investigation is performed to understand the impact of these two variables over key Li-S cell performance parameters. It is demonstrated that Li-S cells’ power performance strongly depends on the E/S ratio, while both E/S ratio and sulfur loading significantly influence the cycle life of Li-S cells. Low E/S ratio and high sulfur loading both give rise to fast lithium anode corrosion, which induces fast capacity fade and Coulombic efficiency decay. Pre-passivation of the lithium anode with an ionic conductor Li 3 PO 4 protection layer only improves the Coulombic efficiency retention at sulfur loading levels much lower than the practical threshold. Meanwhile, increasing the concentration of LiNO 3 additive in the electrolyte is found effective in sustaining the cycling capacity and the Coulombic efficiency over a reasonable usage window (~200 cycles). In conclusion, the role of LiNO 3 is the protection of lithium anode during cycling.
Sulfur cathodes have a high theoretical capacity of 1675 mAh g –1 , making the lithium–sulfur batteries a promising technology for future energy-storage devices. However, their commercial viability is faced with challenges arising from intrinsic electrochemical instabilities and inappropriate cell fabrication parameters. We report here the feasibility of employing TiS 2 as a conductive polysulfide adsorbent, which allows the use of a high amount of electrochemically active polysulfides in building a TiS 2 –polysulfide hybrid cathode. The hybrid cathode exhibits long cycle stability at a C/5 rate over 200 cycles with a high areal capacity and energy density of, respectively, 10 mAh cm –2 and 20 mWh cm –2 , exceeding those of commercial LiCoO 2 . Furthermore, such an enhanced electrochemical performance is obtained in cells with a high sulfur content (65 wt %), high sulfur loading (12 mg cm –2 ), high sulfur mass (12 mg/cathode), and a low electrolyte/sulfur ratio of just 5 μL mg –1 .
An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-stream Mach number of 0.40. Results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio because no corrections for the effects of tunnel-wall constriction on the installation were applied. Slipstream surveys are presented to illustrate blade thrust load distribution for certain operating conditions. Within the range of advance-diameter ratios investigated at each free-stream Mach number, the efficiency of the four-blade propeller decreased as the power coefficient was increased from 0.10 to 1.00. For the three-blade propeller, nearly constant maximum efficiencies were obtained for power coefficients from 0.32 to 0.63 at advance-diameter ratios between 1.90 and 3.00. In general, for conditions below the stall and critical tip Mach number, the maximum thrust load shifted from the inboard sections toward the tip sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall or critical tip Mach number, losses in thrust occurred on the outboard blade sections owing to flow break-down; the thrust load increased slightly on the inboard sections.
The U.S. Department of Energy’s Co-Optima initiative simultaneous focused on diversifying fuel sources, improving efficiency, and reducing emissions through using novel combustion strategies and sustainable fuel blends. For medium-duty/heavy-duty diesel engines, research in this area has led to the development of a multimode strategy that uses premixed charge compression ignition (PCCI) at low loads and conventional diesel combustion (CDC) at mid–high loads. The aim of this study was to understand how emissions were impacted when using PCCI instead of CDC at low loads and switching to an oxygenated biofuel blend. It provides a detailed speciation of the hydrocarbon (HC) and particulate matter (PM) emissions from a multimode medium-duty engine operating at low loads in PCCI and CDC modes and high loads in CDC. The effect of the oxygenated biofuel blend on emissions was studied at all three mode–load conditions using #2 ULSD and a bio-derived fuel (25% hexyl hexanoate (HHN)) blended in #2 ULSD. The PCCI mode effectively decreased NOx, total HC, and PM/PN emissions, with a substantial decrease in larger particles (≥50 nm). A PM/PN reduction was observed at high loads with the 25% HHN fuel. While the total HC emissions were not impacted by fuel type, the detailed HC analysis exposed changes in the HC’s composition.
Catalytic deoxygenation represents a straightforward and core methodology for fine-chemical production and biomass upgrading. Generally, the application of homogeneous metal complexes or heterogeneous noble-metal catalysts prevails in academia and the chemical industry. We introduce cobalt@ordered mesoporous carbon (Co@OMC) catalysts, which are constructed conveniently by a mechanochemical coordination self-assembly based on a renewable tannin precursor. Importantly, the Co@OMC catalysts with a high loading of in situ confined Co species promote the selective deoxygenation of various ketones, aldehydes, and alcohols efficiently into the corresponding alkanes under mild conditions. Therefore, a simple, inexpensive, and heterogeneous catalyst for selective deoxygenation can be expected, meanwhile the solid-state synthesis affords a green, rapid, and scalable pathway to Co@OMC catalysts.
Recent experimental and simulation studies have shown that polymer–nanoparticle (NP) composites (PNCs) with ultra-high NP loading (>50%) exhibit remarkable mechanical properties and dramatic increases in polymer glass-transition temperature, viscosity, and thermal stability compared to the bulk polymer. These deviations in macroscopic properties suggest a slowdown in both segmental and chain-scale polymer dynamics due to confinement. In this work, we examine the polymer conformations and dynamics in these PNCs using molecular dynamics simulations of both unentangled and entangled coarse-grained polymers in random-close-packed NP packings with varying polymer fill fractions. We find that the changes in the polymer dynamics depend on the number of NPs in contact with a polymer segment. Using the number of polymer–NP contacts and different polymer chain conformations as criteria for categorization, we further examine the polymer dynamics at multiple length scales to show the high level of dynamic heterogeneity in PNCs with ultra-high NP loading.
The Qweak experiment at Jefferson Lab (JLab) is a 3000 W hydrogen target scheduled for the summer of 2010 and running for two years until the planned shut-down for 12GeV. The End Station Refrigerator (ESR) supports the three experiment halls, two of which may normally have a hydrogen target. The refrigerator for the ESR is a CTI/Helix 1500 W 4.5-K refrigerator nominally capable of supporting a 1250 W target load at 12 bar and 15-K (plus 1100 W of 4.5-K refrigeration). As such, this refrigerator is not capable of supporting the Qweak experiment target load in its present condition. Additionally, since the installation of an ambient air vaporizer for a single use, two week run duration of a high target load in the summer of 2003 there has been a consistent usage of the Central Helium Liquefier’s (CHL’s) 3 bar 4.5-K helium, supplied via an existing transfer-line to the ESR, for other high target loads. By the fall of 2004, it was apparent that this continued use of CHL’s supercritical helium was routinely being sought by the hall experimenters. As such, a method of refrigeration recovery was proposed to reduce the support required of CHL for these high target loads, including the anticipated Qweak experiment, while utilizing the recovered CHL refrigeration from the target to increase ESR’s 12 bar 15-K capacity.
High-loading and high quality PSU Si anode has been optimized and fabricated. The electrochemical performance has been utilized. The PSU Si-graphite anode exhibits the mass loading of 5.8 mg/cm2, charge capacity of 850 mAh/ g and good cycling performance. This optimized electrode has been used for full-cell fabrication. The performance enhancement of Ni-rich materials can be achieved by a diversity of strategies. Higher Mn content and a small amount of Al doping can improve the electrochemical performance by suppressing interfacial side reactions with electrolytes, thus greatly benefiting the cyclability of the samples. Also, surface coatings of Li-rich materials and AlF 3 are able to improve the performance stability of Ni-rich cathodes. One kilogram of optimized concentration-gradient LiNi 0.76 Co 0.10 Mn 0.14 O 2 (CG) with careful control of composition, morphology and electrochemical performance was delivered to our collaborators. The sample achieved an initial specific capacity close to 190 mA h g -1 at C/10 rate and 180 mA h g -1 at C/3 rate as well as good cyclability in pouch full cells with a 4.4 V upper cut-off voltage at room temperature. Electrolyte additive with Si-N skeleton forms a less resistant SEI on the surface of silicon anode (from PSU) as evidenced by the evolution of the impedance at various lithiation/de-lithiation stages and the cycling data The prelithiation result demonstrates a solution processing method to achieve large area, uniform SLMP coating on well-made anode surface for the prelithiation of lithium-ion batteries. The prelithiation effect with this method is applied both in graphite half cells, graphite/NMC full cells, SiO half cells, SiO/NMC full cells, Si-Graphite half cells and Si-Graphite/NMC full cells with improvements in cycle performance and higher first cycle coulombic efficiency than their corresponding cells without SLMP prelithiation. As to the full cell fabrication and test, full pouch cells with high capacity of 2.2 Ah and 1.2 Ah have been fabricated and delivered. The cells show great uniformity and good cycling performance. The prelithiation method effectively compensate the loss in the first cycle. The cell with high energy density and long-cycle life has been achieved.