Search NASA⌕ Search

SEARCH · Search NASA

Results for “hydrodynamic loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Piezoviscous effects in nonconformal contacts lubricated hydrodynamically

The analysis is concerned with the piezoviscous-rigid regime of lubrication for the general case of elliptical contacts. In this regime several formulas of the lubricant film thickness have been proposed by Hamrock and Dowson, by Dowson et al., and more recently by Houpert. However, either they do not include the load parameter W, which has a strong effect on film thickness, or they overestimate the film thickness by using the Barus formula for pressure-viscosity characteristics. The Roelands formula was used for the pressure-viscosity relationship. The effects of the dimensionless load, speed, and materials parameters, the radius ratio, and the lubricant entrainment direction were investigated. The dimensionless load parameter was varied over a range of one order of magnitude. The dimensionless speed parameter was varied by 5.6 times the lowest value. Conditions corresponding to the use of solid materials of steel, bronze, and silicon nitride and lubricants of paraffinic and naphthenic mineral oil were considered in obtaining the exponent in the dimensionless materials parameter. The radius ratio was varied from 0.2 to 64 (a configuration approaching a line contact). Forty-one cases were used in obtaining a minimum film thickness formula. Contour plots indicate in detail the pressure developed between the contacting solids.

Jeng, Yeau-Ren↗
DOE OSTI2025

SAN-Based Block Polymers as a Platform for Manufacturing Strong Isoporous Membranes

Ultrafiltration (UF) membranes are ubiquitous in water purification and bioprocessing. However, co-designing their mechanical and transport properties remains challenging because of the broad pore size distributions at the surface and within the bulk that result from nonsolvent-induced phase separation (NIPS) – their typical manufacturing process. These distributions influence the hydrodynamic resistance to water flow and the stress concentrations around the pores. Developing advanced UF membranes requires innovative molecular designs that offer control over the surface and bulk pores, as well as the mechanical properties of the load-bearing, polymer. Here, we introduce a platform for designing UF membranes by leveraging solution self-assembly of block polymers and chain architectures with pendant polar groups. The block polymers consist of a poly(styrene-co-acrylonitrile) hydrophobic block, which is known for its strength, and a poly(4-vinyl pyridine) hydrophilic block, which drives solution self-assembly. We focus on a series of block polymers with constant molecular weight, M n ≈ 115 kDa, SAN fraction, 75 wt.%, and varying acrylonitrile content, 0 to 40 mol%, to demonstrate that: (i) RAFT dispersion copolymerization of acrylonitrile and styrene provides a facile route to synthesize strong block polymers, (ii) incorporation of acrylonitrile into the hydrophobic block enhances membrane strength by facilitating chain entanglements and dipole-dipole interactions, and (iii) acrylonitrile alters the balance between membrane permeance and rejection, even when the membranes feature similar surface and bulk pores. Overall, our results provide insights into the molecular design of UF membranes with enhanced mechanical and separation properties, contributing to the development of materials for water and energy technologies.

deformation↗
DOE OSTI2022

Constrained model calibration of grain structure dependent spall dynamics in shock-loaded tantalum

Here, we perform a gas gun experiment by shock loading tantalum samples of varying grain structures to assess the suitability of a numerical model for simulating spall behavior. The observed differences in spall strength, as well spallation and re-compression history, are not captured in uncalibrated hydrodynamic simulations. An optimization is performed on the Johnson spall model to determine the best parameters that fit the observed trends. Linear stability analysis is employed to motivate bounds on those parameters. Herein, optimized simulations agree well with the experimental results, reproducing pullback depth and recompression timescales across the different samples tested. Further, the observed pullback time of the single crystal sample was found to imply, via the stability analysis, a percolation threshold in good agreement with the theoretical value for a body centered cubic lattice. Therefore, the combined linear stability and percolation analysis shows promise and may be applied to other materials with diverse microstructures. Collectively, the findings demonstrate that the model is suitable for reproducing spall-induced free surface behavior across various microstructures, but also points to caution in using model coefficients for uncalibrated microstructures.

58 GEOSCIENCES↗
NASA NTRS1974

Asperity lubrication and cavitation in face seals

The basic aspect of parallel-surface lubrication that distinguishes it from other areas of lubrication technology is that classical lubrication theory does not predict the existence of a stable hydrodynamic film for steady-state, isothermal, incompressible flow between smooth, parallel surfaces. Hydrodynamic films between apparently parallel surfaces have been observed in practice and are often essential for the reliable performance of thrust bearings and seals. In order to account for this fortunate discrepancy between classical theory and experiment, load-support mechanisms relating to accidential features characteristic of seal performance, which relax one or more of the assumptions in the classical theory and permit the theoretical prediction of load support are proposed. Some of the features that have been analyzed are vibratory effects such as wobble and bounce, surface waviness, nonsymmetric rotation resulting from various types of misalignment, lubricant density change, non-Newtonian lubricant effects, and surface roughness.

Walowitt, J. A.↗
NASA NTRS1982

Lubrication of rigid ellipsida solids

The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds boundary conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza' classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared by using the exact expression for the film in the analysis. Contour plots are known that indicate in detail the pressure developed between the solids.

Hamrock, B. J.↗
NASA NTRS1984

Lubrication of Machine Elements

The understanding of hydrodynamic lubrication began with the classical experiments of Tower and Petrov. Reynolds used a reduced form of the Navier-Stokes equations and the continuity equation to generate a second order differential equation for the pressure in the narrow, converging gap of a bearing contact. Such a pressure enables a load to be transmitted between the surfaces with very low friction since the surfaces are completely separated by a film of fluid. In such a situation it is the physical properties of the lubricant, notably the dynamic viscosity, that dictate the behavior of the contact. The understanding of boundary lubrication is normally attributed to Hardy and Doubleday. In boundary lubrication it is the physical and chemical properties of thin films of molecular proportions and the surfaces to which they are attached that determine contact behavior. The lubricant viscosity is not an influential parameter. Research is devoted to a better understanding and more precise definition of other lubrication regimes between these extremes. One such regime, elastohydrodynamic lubrication, occurs in nonconformal contacts, where the pressures are high and the bearing surfaces deform elastically. In this situation the viscosity of the lubricant may raise considerably, and this further assists the formation of an effective fluid film. The science of these three lubrication regimes (hydrodynamic, elastohydrodynamic, and boundary) are described and the manner in which this science is used in the design of machine elements is examined.

Hamrock, Bernard J.↗
NASA NTRS1986

Flow rate and trajectory of water spray produced by an aircraft tire

One of the risks associated with wet runway aircraft operation is the ingestion of water spray produced by an aircraft's tires into its engines. This problem can be especially dangerous at or near rotation speed on the takeoff roll. An experimental investigation was conducted in the NASA Langley Research Center Hydrodynamics Research Facility to measure the flow rate and trajectory of water spray produced by an aircraft nose tire operating on a flooded runway. The effects of various parameters on the spray patterns including distance aft of nosewheel, speed, load, and water depth were evaluated. Variations in the spray pattern caused by the airflow about primary structure such as the fuselage and wing are discussed. A discussion of events in and near the tire footprint concerning spray generation is included.

Daugherty, Robert H.↗
NASA NTRS1997

A New Foil Air Bearing Test Rig for Use to 700 C and 70,000 rpm

A new test rig has been developed for evaluating foil air bearings at high temperatures and speeds. These bearings are self acting hydrodynamic air bearings which have been successfully applied to a variety of turbomachinery operating up to 650 C. This unique test rig is capable of measuring bearing torque during start-up, shut-down and high speed operation. Load capacity and general performance characteristics, such as durability, can be measured at temperatures to 700 C and speeds to 70,000 rpm. This paper describes the new test rig and demonstrates its capabilities through the preliminary characterization of several bearings. The bearing performance data from this facility can be used to develop advanced turbomachinery incorporating high temperature oil-free air bearing technology.

DellaCorte, Chris↗
DOE OSTI2020

Polystyrene-block-Polydimethylsiloxane as a Potential Silica Substitute for Polysiloxane Reinforcement

We report here on microphase-separated poly(styrene-block-dimethylsiloxane) (PS-b-PDMS) as a reinforcing filler in PDMS thermosets that overcomes the long-standing problem of aging in the processing of silica-reinforced silicone. Surprisingly, PS-b-PDMS reinforced composites display comparable mechanical performance to silica-modified analogs, even though the modulus of PS is much smaller than that of silica and there is no evidence of percolation with respect to the rigid PS domains. We have found that a few unique characteristics contribute to the reinforcing performance of PS-b-PDMS. The strong self-assembly behavior promotes batch-to-batch repeatability by having well-dispersed fillers. The structure and size of the fillers depend on the loading and characteristics of both filler and matrix, along with the shear effect. The reinforcing effect of PS-b-PDMS is mostly brought by the entanglements between the corona layer of the filler and the matrix, rather than the hydrodynamic reinforcement of the PS phase.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks

Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.

42 ENGINEERING↗
NASA NTRS1940

The calculated effect of various hydrodynamic and aerodynamic factors on the take-off of a large flying boat

Report presents the results of an investigation made to determine the influence of various factors on the take-off performance of a hypothetical large flying boat by means of take-off calculations. The factors varied in the calculations were size of hull (load coefficient), wing setting, trim, deflection of flap, wing loading, aspect ratio, and parasite drag. The take-off times and distances were calculated to the stalling speeds and the performance above these speeds was separately studied to determine piloting technique for optimum take-off.

Olson, R E↗
DOE OSTI2021

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗
NASA NTRS1978

Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. 1: Journal bearing performance

A 38.1 mm (1.5 inch) diameter Hydresil Compliant Surface Air Lubricated Journal Bearing was designed and tested to obtain bearing performance characteristics at both room temperature and 315 C (600 F). Testing was performed at various speeds up to 60,000 rpm with varying loads. Rotating sensors provided an opportunity to examine the film characteristics of the compliant surface bearing. In addition to providing minimum film thickness values and profiles, many other insights into bearing operation were gained such as the influence of bearing fabrication accuracy and the influence of smooth foil deflection between the bumps.

Ruscitto, D.↗
DOE OSTI2022

The role of pre-existing heterogeneities in materials under shock and spall

There has been a challenge for many decades to understand how heterogeneities influence the behavior of materials under shock loading, eventually leading to spall formation and failure. Experimental, analytical, and computational techniques have matured to the point where systematic studies of materials with complex microstructures under shock loading and the associated failure mechanisms are feasible. This is enabled by more accurate diagnostics as well as characterization methods. As interest in complex materials grows, understanding and predicting the role of heterogeneities in determining the dynamic behavior becomes crucial. Early computational studies, hydrocodes, in particular, historically preclude any irregularities in the form of defects and impurities in the material microstructure for the sake of simplification and to retain the hydrodynamic conservation equations. Contemporary computational methods, notably molecular dynamics simulations, can overcome this limitation by incorporating inhomogeneities albeit at a much lower length and time scale. This review discusses literature that has focused on investigating the role of various imperfections in the shock and spall behavior, emphasizing mainly heterogeneities such as second-phase particles, inclusions, and voids under both shock compression and release. Pre-existing defects are found in most engineering materials, ranging from thermodynamically necessary vacancies, to interstitial and dislocation, to microstructural features such as inclusions, second phase particles, voids, grain boundaries, and triple junctions. This literature review explores the interaction of these heterogeneities under shock loading during compression and release. Systematic characterization of material heterogeneities before and after shock loading, along with direct measurements of Hugoniot elastic limit and spall strength, allows for more generalized theories to be formulated. Further, continuous improvement toward time-resolved, in situ experimental data strengthens the ability to elucidate upon results gathered from simulations and analytical models, thus improving the overall ability to understand and predict how materials behave under dynamic loading.

36 MATERIALS SCIENCE↗
DOE OSTI2024

TEAMER: Crossflow Turbine Fairing Geometry Optimization - Report and CFD Modeling Files

The dataset includes computational fluid dynamics (CFD) models and simulation files for crossflow turbines as well as a detailed project report. The report documents the project undertaken by the Ocean Renewable Power Company (ORPC) to design and optimize a modular fairing for the Modular RivGen Marine Hydrokinetic (MHK) turbine, which enhances the efficient deployment and operation of turbine arrays. The project focused on optimizing the hydrodynamic performance of the fairing using CFD, with an emphasis on two key geometric parameters: the fairing's cross-sectional shape and the spacing between the rotor and the fairing. The analysis aimed to maximize net power output while also assessing discretized loading to evaluate ultimate and fatigue loads on the turbine components. The numerical modeling was conducted using both the commercial CFD software Star-CCM+ and the open-source code openFOAM, with the latter utilizing the actuator line library, turbinesFOAM. This dual-code approach was intended to increase confidence in the results and demonstrate the viability of using open-source tools for high-fidelity marine energy modeling. This dataset includes all necessary files for actuator line simulations in openFOAM, as well as 2D blade-resolved CFD results, along with Python and Java scripts for setting up and post-processing simulations.

16 TIDAL AND WAVE POWER↗
NASA NTRS1982

Bearings: Technology and needs

A brief status report on bearing technology and present and near-term future problems that warrant research support is presented. For rolling element bearings a material with improved fracture toughness, life data in the low Lambda region, a comprehensive failure theory verified by life data and incorporated into dynamic analyses, and an improved corrosion resistant alloy are perceived as important needs. For hydrodynamic bearings better definition of cavitation boundaries and pressure distributions for squeeze film dampers, and geometry optimization for minimum power loss in turbulent film bearings are needed. For gas film bearings, foil bearing geometries that form more nearly optimum film shapes for maximum load capacity, and more effective surface protective coatings for high temperature operation are needed.

Anderson, W. J.↗
NASA NTRS1987

Development of gas-to-gas lift pad dynamic seals, volumes 1 and 2

Dynamic tests were performed on self acting (hydrodynamic) carbon face rotary shaft seals to assess their potential, relative to presently used labyrinth seals, for improving performance of aircraft gas turbine engines by reducing air leakage flow rate at compressor end seal locations. Three self acting bearing configurations, designed to supply load support at the interface of the stationary carbon seal and rotating seal race, were tested. Two configurations, the shrouded taper and shrouded flat step, were incorporated on the face of the stationary carbon seal element. The third configuration, inward pumping spiral grooves, was incorporated on the hard faced surface of the rotating seal race. Test results demonstrated seal leakage air flow rates from 75 to 95% lower that can be achieved with best state-of-the-art labyrinth designs and led to identification of the need for a more geometrically stable seal design configuration which is presently being manufactured for subsequent test evaluation.

Pope, A. N.↗
NASA NTRS1947

Hydrodynamic Qualities of a 1/10-Size Powered Dynamic Model of the XP5Y-1 Flying Boat in Smooth Water: Langley Tank Model 246, TED No. NACA DE 320

The hydrodynamic characteristics of a 1/10-size powered dynamic model of the XP5Y-1 flying boat were determined in Langley tank no. 1. Stable take-offs were possible at all practicable positions of the center of gravity and flap deflections. An increase in gross load from 123.5 to 150.0 pounds (21.5 percent) had only a slight effect on the stable range for take-off. A decrease in forward acceleration from 3.0 to 1.0 feet per second per second had only a very small effect on the stable range for take-off. In general, the landings were free from skipping except at trims below 6 deg where one skip was encountered at an aft position of the center of gravity. The model porpoised during the landing runout at all positions of the center of gravity when landed at trims above 10 deg. Spray in the propellers was light at the design gross load, and was not considered excessive,at a gross load of 136.0 pounds.

Woodward, David R.↗