Search NASA⌕ Search

SEARCH · Search NASA

Results for “improve standardization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Improving Chirped Fiber Bragg Grating Resolution for Position-Sensitive Sensors in Shock- and Detonation-Driven Experiments

Chirped fiber Bragg gratings (CFBGs) are robust diagnostic sensors that are widely used to track detonation-driven and shock wave propagation. CFBGs are inscribed with a linearly chirped periodic index of refraction changes that alter the Bragg wavelength along the length of the probe. The light return of each individual Bragg element is captured by a detector at a unique time to map the full reflected spectrum. The CFBG spectrum is measured with a dispersive Fourier transform of the reflected light that temporally stretches the spectrum to increase spatial resolution and make a one-to-one map of the wavelength on a time axis. Here, we propose an improvement of CFBG temporal resolution by incorporating two co-linear laser pulses with orthogonal polarization states and a 5 ns time offset. The two separate signals were split and tracked by two separate detectors. An oscilloscope captured good separation in the signals, and two separate spectrograms were generated and interleaved in the post-processing of the data. This novel technique doubled the CFBG temporal resolution and led to a doubled location resolution. As a proof-of-concept of this technique, the resolution improvement was compared between standard CFBG measurements and the two polarization states method on a position-sensitive CFBG sensor. CFBG resolution doubling will advance sensor capabilities and will have a direct impact on improving capture and analysis in dynamic, high-explosive experiments.

42 ENGINEERING↗
NASA NTRS1987

Design, fabrication and delivery of a miniature Cassegrainian concentrator solar array system

The optical design of the miniature Cassegrainian concentrator (MCC) element was improved for both offpoint and onpoint power capability. The cell stack design has shown no losses under the high short term thermal stresses imposed by component level test and is projected to be capable of greater than five years thermal cycle life in low Earth orbit. The structural design met all requirements for stiffness and flatness and requires adjustable inserts for fine tuning of the GFRP structure to meet flatness goals. The completed, fully populated small and large MCC panels deliverable under this contract perform electrically as expected. A solid acceptance inspection program to guarantee quality of all purchased parts, and continued manufacturing process improvements will make the MCC design a viable low cost alternative to standard flat panel technology. Minor improvements to the cell stack design of the MCC element can make significant improvements in both the performance and manufacturability of the MCC system.

Kruer, Mark A.↗
NASA NTRS2019

Characterization of IM7/8552 Thin-Ply and Hybrid Thin-Ply Composites

Composite materials have increasingly been used for aerospace applications due to improved performance and reduced weight compared to their metallic counterparts. Inclusion of thin-ply material, plies with cured thickness half or less than standard composites, have potential to improve performance and reduce structural weight. Limited characterization of thin-ply IM7/8552 material in 30 and 70 grams per square meter fiber areal weights has been carried out using a series of selected American Society for Testing and Materials (ASTM) tests. Tests included unnotched tension, unnotched compression, v-notched rail shear, open-hole tension, and open-hole compression. Unidirectional, cross-ply, quasiisotropic and hybrid hard laminates were included in the study, and were compared to standard-ply laminates. Properties compared include fiber volume, laminate moduli, and failure strength, with failure modes also being examined. The thin-ply specimens exhibited similar or superior performance to standard ply laminates in many of the cases compared. Improvements in strength for laminates containing thin-ply material were seen for unidirectional laminates under unnotched tension, quasi-isotropic laminates under unnotched tension and compression, and hard laminates under open hole tension. Additional investigation is required to determine appropriate ply stacking rules for hybrids of thin and standard plies to avoid undesirable failure modes such as axial splitting. However, the observed performance improvements demonstrated by the conducted ASTM tests of hybrid thin-ply hard laminates could have benefits for improved structural weight in aircraft.

Lovejoy, Andrew E.↗
NASA NTRS2019

CMB Spectral Distortions: Status and Prospects

Departures of the energy spectrum of the cosmic microwave background (CMB) from a perfect blackbody probe a fundamental property of the universe - its thermal history. Current upper limits, dating back some 25 years, limit such spectral distortions to 50 parts per million and provide a foundation for the Hot Big Bang model of the early universe. Modern upgrades to the 1980's-era technology behind these limits enable three orders of magnitude or greater improvement in sensitivity. The standard cosmological model provides compelling targets at this sensitivity, spanning cosmic history from the decay of primordial density perturbations to the role of baryonic feedback in structure formation. Fully utilizing this sensitivity requires concurrent improvements in our understanding of competing astrophysical foregrounds. We outline a program using proven technologies capable of detecting the minimal predicted distortions even for worst-case foreground scenarios.

Kogut, A.↗
NASA NTRS2020

Perspectives on Data Reproducibility and Replicability in Paleoclimate and Climate Science

This paper summarizes the current state of reproducibility and replicability in the fields of climate and paleoclimate science, including brief histories of their development and applications in climate science, new and recent approaches towards improvement of reproducibility and replicability, and challenges. Recommendations for addressing those challenges include: development of searchable, auto-updated, interlinked, multi-archive public paleoclimate repositories for raw and processed digital datasets; cross-center standardized code base cases, improved data storage techniques, and a focus on replicability for climate simulation storage and access; and support of the development and community awareness of findable, accessible, interoperable and reusable (FAIR) principles by funding agencies and publishers. This paper is largely based on the May 2018 presentations of a panel of researchers to the Committee on Reproducibility and Replicability in Science, part of the National Academies of Science, Engineering, and Medicine. The commentary and recommendations made here are in alignment with those of its Consensus Study Report on Reproducibility and Replicability in Science (2019).

data repositories↗
NASA NTRS1968

Improved atomic resonance gas cell for use in frequency standards

Atomic resonance gas cell maintains a stable operating frequency in the presence of pressure fluctuations in the ambient atmosphere. The new cell includes an envelope which is transparent to radiation in the optical region and to microwave energy at the atomic resonance frequency of the alkali-metal vapor within the envelope.

Huggett, G. R.↗
DOE OSTI2024

Elevated Temperature Graphite Mechanical Testing

High purity graphite will be used for core components within most High Temperature Reactor (HTR) designs. Several "high tech” industries currently utilize synthetic, high-purity, commercially available graphite components to fabricate photovoltaic cells, semi-conductors, optical fibers, and other high value electronic industry products. New advanced HTR designs are also interested in using these graphite grades for long-term, internal core component applications. Consequently, the US Department of Energy, Advanced Reactor Technologies (DOE-ART) program has spent several years testing different high purity graphite grades for potential use within these new nuclear reactor designs. A significant part of that effort has been in the development and improvement of American Society for Testing and Materials (ASTM) test standards specifically for nuclear graphite grades. Nearly all ASTM test standards have either been developed or improved by the DOE-ART program over the past 25 years. The ART program continues to assist in the development of new ASTM test standards in support of the future commercial HTR fleet currently being designed and built in the USA. The newest effort undertaken by ART is the development of high temperature mechanical testing practices that may be acceptable for a future ASTM test standard (or guide) for this critical material property measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Higher Efficiency, Demand Flexible Refrigerator with On-Demand Micro-Vibrational De-icing Technology

Refrigerator technology has advanced significantly over the last couple of decades. Today’s refrigerators use only about 25% of the energy that was required to power models built in 1975. Even as they continually improve efficiency to meet standards, refrigerators have increased in size by almost 20%, added energy-consuming features such as through-the-door ice, and provide more benefits than ever before. However, a few challenges and technology gaps are preventing further improvement of the demand responsiveness and efficiency of the refrigerators. One of the major technology gaps in existing refrigerators is their outdated de-icing process. When the evaporator generates frost, an old-fashioned resistive heating element melts the ice. Most refrigerators have a timed defrost cycle, rather than an active system that could monitor the state of the frost. In these systems, not only is the precious electricity used at its least efficient form of conversion (direct conversion of electricity to heat), but also all the latent heat associated with the ice is wasted during the melting process. On top of that, the refrigerator needs to work harder to pull the temperature down after defrosting, and, last but not least, the food quality is severely impacted by the temperature swings during the defrost cycle. According to a study, the EU alone wastes 89 million tons of food in the supply chain every year. Any temperature swing during defrosting (about 6F according to Emerson for low-temperature cases) can negatively impact the shelf life of meat and other products for multiple days. All these issues can happen during the peak demand time of the electric grid. Unlike the conventional systems, the proposed novel advanced micro-vibrational deicing process uses no heat for defrosting. Instead, it uses the micro vibrations generated by a piezoelectric or vibration-generating module to mechanically break ice from the heat exchanger almost instantaneously. The project titled “Higher Efficiency, Demand Flexible Refrigerator with On-Demand Micro-Vibrational De-icing Technology, performed by Ultrasonic Technology Solutions, LLC (UTS) of Knoxville, TN, in collaboration with Emerson (now Copeland), represents the final phase of a multi-year effort funded under the U.S. Department of Energy’s Building Technologies Office (BTO) BENEFIT FOA 2020. Initiated on October 1, 2021, and completed after a nine-month no-cost extension ending September 30, 2025, this project aimed to develop and validate a novel micro-vibrational mechanical defrosting system, achieving more than 25% improvement in defrosting energy efficiency over conventional baseline defrosting technologies. Over sixteen quarters, the project advanced from fundamental ice-mechanical characterization and prototype development to full-scale system integration and validation. Initial efforts established project management infrastructure and characterized ice adhesion properties, followed by the design and fabrication of early aluminum-based prototypes for resonance frequency testing. Subsequent quarters saw rapid technical progression, including the identification of optimal piezoelectric and motor-based vibration mechanisms, the demonstration of effective de-icing over 6x6-inch aluminum surfaces. The team achieved its Go/No-Go milestone by exceeding the 25% energy-efficiency improvement target—reaching up to 3,340% under optimized conditions—and later confirmed that motor-driven systems offered superior performance and energy efficiency compared to piezoelectric alternatives. Continued refinement led to the development of amplifier systems on printed circuit boards, improved control and instrumentation hardware, and integration into full-scale heat exchanger (HX) prototypes at both UTS and Copeland facilities. Multiple vibration-mounting studies and frost-growth experiments guided mechanical optimization and noise-mitigation strategies, achieving a 17.5 dB reduction in sound pressure level and verifying robust mechanical performance. Advanced analyses, including modal and harmonic simulations, established a quantitative understanding of vibrational behavior and de-icing efficiency across >1000 cm² systems. The final project phase successfully demonstrated scalable integration within reach-in and chest freezer prototypes, confirmed >25% efficiency improvements in large-area systems, and completed a comprehensive business model and scale-up strategy identifying electric defrost systems as the primary beachhead market. The culmination of this DOE-supported effort establishes micro-vibrational defrosting as a viable, high-efficiency, low-noise, and demand-flexible de-icing technology, paving the way for commercial deployment and broader application in next-generation refrigeration systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2014

Physics-Based Fragment Acceleration Modeling for Pressurized Tank Burst Risk Assessments

As part of comprehensive efforts to develop physics-based risk assessment techniques for space systems at NASA, coupled computational fluid and rigid body dynamic simulations were carried out to investigate the flow mechanisms that accelerate tank fragments in bursting pressurized vessels. Simulations of several configurations were compared to analyses based on the industry-standard Baker explosion model, and were used to formulate an improved version of the model. The standard model, which neglects an external fluid, was found to agree best with simulation results only in configurations where the internal-to-external pressure ratio is very high and fragment curvature is small. The improved model introduces terms that accommodate an external fluid and better account for variations based on circumferential fragment count. Physics-based analysis was critical in increasing the model's range of applicability. The improved tank burst model can be used to produce more accurate risk assessments of space vehicle failure modes that involve high-speed debris, such as exploding propellant tanks and bursting rocket engines.

Acceleration↗
NASA NTRS1988

Future MAUS payload and the TWIN-MAUS configuration

The German MAUS project (materials science autonomous experiments in weightlessness) was initiated in 1979 for optimum utilization of NASA's Get Away Special (GAS) program. The standard MAUS system was developed to meet GAS requirements and can accommodate a wide variety of GAS-type experiments. The system offers a range of services to experimenters within the framework of standardized interfaces. Four MAUS payloads being prepared for future space shuttle flight opportunities are described. The experiments include critical Marangoni convection, oscillatory Marangoni convection, pool boiling, and gas bubbles in glass melts. Scientific objectives as well as equipment hardware are presented together with recent improvements to the MAUS standard system, e.g., a new experiment control and data management unit and a semiconductor memory. A promising means of increasing resources in the field of GAS experiments is the interconnection of GAS containers. This important feature has been studied to meet the challenge of future advanced payloads. In the TWIN-MAUS configuration, electrical power and data will be transferred between two containers mounted adjacent to each other.

Staniek, S.↗
NASA NTRS1983

Vehicle test report: South Coast Technology electric Volkswagen Rabbit with developmental low-power armature chopper

Dynamometer performance of a South Coast Technology electric conversion of a Volkswagen (VW) Rabbit designated SCT-8 was tested. The SCT-8 vehicle was fitted with a transistorized chopper in the motor armature circuit to supplement the standard motor speed control via field weakening. The armature chopper allowed speed control below the motor base speed. This low speed control was intended to reduce energy loss at idle during stop-and-go traffic; to eliminate the need for using the clutch below base motor speed; and to improve the drivability. Test results indicate an improvement of about 3.5% in battery energy economy for the SAE J227a-D driving cycle and 6% for the C-cycle with only a minor reduction in acceleration performance. A further reduction of about 6% would be possible if provision were made for shutting down field power during the idle phases of the driving cycles. Drivability of the vehicle equipped with the armature chopper was significantly improved compared with the standard SCT Electric Rabbit.

Marte, J. E.↗
DOE OSTI2024

Enhancing Electron Microscopy Image Classification Using Data Augmentation

Manual labeling for machine learning tasks such as image classification is tedious and labor-intensive; as a result, scientific datasets suitable for deep learning applications are scarce and limited. While data augmentation techniques have shown promise for extending image datasets, very little work has been done to understand the impact of combining multiple augmentation methods sequentially or the limits of their effectiveness when combined. Our work addresses this gap by examining how standard and combinatorial data augmentation affects the performance of machine learning models when trained on small datasets for label classification tasks. For our analysis, we generate single, double and quadruple-augmented datasets for a microscopy image classification task using six standard augmentation methods, and compare the resultant improvements observed in binary classification accuracy with three standard image classification models (DenseNet169, MobileNetV2, ResNet101V2). Our experiments show a non-monotonic relationship between the number of simultaneous augmentation methods and classification accuracy, indicating that there is a trade-off between the degree of augmentation and the model performance. These findings suggest that the optimal number of augmentation methods will vary by domain and use case. We also find that the order in which augmentation methods are applied to a limited dataset matters when combining augmentation schemes, with our use case showing performance differences up to 2.6% when the augmentation order is reversed for double-augmented datasets. Our work offers insights to the limits of data augmentation when working on image classification tasks with limited datasets.

Welsman, Jordan A↗
DOE OSTI2026

AmeriFlux FLUXNET-1F US-ABc Archbold grazed improved pasture

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-ABc Archbold grazed improved pasture. This is the FLUXNET version of the carbon flux data for the site US-ABc Archbold grazed improved pasture produced by applying the standard ONEFlux (1F) software. Site Description - This site is an improved pasture, regularly fertilized (nitrogen, ~26 kg/ha every 2 years) and limed (~229 kg/ha every 5 years, and historically received phosphorus fertilizer until 1986; . The soil type is a fine sandy Spodosol

Bernacchi, Carl [Global Change and Photosynthesis ↗
DOE OSTI2026

AmeriFlux FLUXNET-1F US-ABd Archbold ungrazed improved pasture

This is the AmeriFlux Management Project (AMP) created FLUXNET-1F version of the carbon flux data for the site US-ABd Archbold ungrazed improved pasture. This is the FLUXNET version of the carbon flux data for the site US-ABd Archbold ungrazed improved pasture produced by applying the standard ONEFlux (1F) software. Site Description - This site is an improved pasture, regularly fertilized (nitrogen, ~26 kg/ha every 2 years) and limed (~229 kg/ha every 5 years; and historically received phosphorus fertilizer until 1986; . The soil type is a fine sandy Spodosol . Grazing was removed in 2013-2015 for the duration of the study

Bernacchi, Carl [Global Change and Photosynthesis ↗
NASA NTRS2001

NASA's Lessons Learned and Technical Standards: A Logical Marriage

Lessons Learned have been the basis for our accomplishments throughout the ages. They have been passed down from father to son, mother to daughter, teacher to pupil, and older to younger worker. Lessons Learned have also been the basis for NASA's accomplishments for more than forty years. Both government and industry have long recognized the need to systematically document and utilize the knowledge gained from past experiences in order to avoid the repetition of failures and mishaps. Lessons Learned have formed the foundation for discoveries, inventions, improvements, textbooks, and Technical Standards.

Gill, Paul↗
DOE OSTI2025

Heat load measurements for the PIP-II pHB650 cryomodule

This study presents a brief overview of the 1st and 2nd phases and an in-depth analysis of the 3rd phase heat load testing performed on the pHB650 (prototype High Beta 650 MHz) cryomodule at PIP2IT (PIP-II Injector Test Facility), with a focus on both the results and the methodological advancements that have improved testing efficiency and accuracy. A key challenge identified in the testing campaign is the higher-than-expected heat loads observed in the first PIP-II (Proton Improvement Plan II) prototype cryomodules (pSSR1 and pHB650) tested at PIP2IT. Elevated heat loads are concerning given the fixed capacity of the PIP-II cryoplant that is currently being installed at Fermilab. However, understanding the sources of these elevated heat loads offers a critical opportunity to implement effective heat load mitigations on upcoming PIP-II cryomodules to stay within the available capacity of the PIP-II cryoplant. The study includes a summary of test results, descriptions of measurement procedures, and key observations on parameters directly and indirectly related to heat load measurements. Direct observations include measured heat loads and the effectiveness of JT heat exchanger under varying conditions, while indirect observation analyze factors such as the temperature distribution on the two-phase pipe and relief piping under varying conditions. Thermal acoustic oscillations (TAO) were identified during testing, which was mitigated by replacing the original G10 stem with a stainless steel stem equipped with wipers for the cryomodule cooldown valve. A major innovation during pHB650 Phase 3 testing was the development of an automated Python script to streamline data acquisition, analysis, and reporting of heat load results. This script automatically retrieved data from ACNET (Accelerator Control Network), performed heat load calculations, and generated detailed reports featuring plots and tables. This advancement significantly reduced manual labor and enhanced the thoroughness of data analysis compared to earlier campaigns. The heat load test reports were promptly uploaded to the electronic logbook shortly after each test, enabling rapid feedback and collaboration between the SRF and cryogenic teams. The heat load measurements included various components: HTTS (high-temperature thermal shield), LTTS (low-temperature thermal shield), 2K isothermal and non-isothermal heat loads. Results were recorded both within the cryomodule and between the bayonet can supply and return. Measurements were conducted under different operating conditions such as "standard", "linac", and "simulated dynamic". Additionally, HTTS and LTTS heat loads were calculated in real time, allowing for the tracking of thermal stability and identification of changes during testing, both in steady-state and transient conditions. The results of this testing campaign not only provide valuable insights into the performance of the pHB650 cryomodule but also highlight best practices and lessons learned that will inform future cryomodule testing at PIP2IT. These include adopting automated tools for data analysis, refining real-time measurement capabilities, and emphasizing detailed pre-test planning. The framework established in this campaign aims to set an improved standard for cryomodule testing and heat load reporting in future cryomodule test campaigns.

Porwisiak, D. [Fermilab; Wroclaw Tech. U.]↗
NASA NTRS1992

The need for GPS standardization

A desirable and necessary step for improvement of the accuracy of Global Positioning System (GPS) time comparisons is the establishment of common GPS standards. For this reason, the CCDS proposed the creation of a special group of experts with the objective of recommending procedures and models for operational time transfer by GPS common-view method. Since the announcement of the implementation of Selective Availability at the end of last spring, action has become much more urgent and this CCDS Group on GPS Time Transfer Standards has now been set up. It operates under the auspices of the permanent CCDS Working Group on TAI and works in close cooperation with the Sub-Committee on Time of the Civil GPS Service Interface Committee (CGSIC). Taking as an example the implementation of SA during the first week of July 1991, this paper illustrates the need to develop urgently at least two standardized procedures in GPS receiver software: monitoring GPS tracks with a common time scale and retaining broadcast ephemeris parameters throughout the duration of a track. Other matters requiring action are the adoption of common models for atmospheric delay, a common approach to hardware design and agreement about short-term data processing. Several examples of such deficiencies in standardization are presented.

W. Lewandowski↗
NASA NTRS2001

Lessons Learned and Technical Standards: A Logical Marriage

A comprehensive database of lessons learned that corresponds with relevant technical standards would be a boon to technical personnel and standards developers. The authors discuss the emergence of one such database within NASA, and show how and why the incorporation of lessons learned into technical standards databases can be an indispensable tool for government and industry. Passed down from parent to child, teacher to pupil, and from senior to junior employees, lessons learned have been the basis for our accomplishments throughout the ages. Government and industry, too, have long recognized the need to systematically document And utilize the knowledge gained from past experiences in order to avoid the repetition of failures and mishaps. The use of lessons learned is a principle component of any organizational culture committed to continuous improvement. They have formed the foundation for discoveries, inventions, improvements, textbooks, and technical standards. Technical standards are a very logical way to communicate these lessons. Using the time-honored tradition of passing on lessons learned while utilizing the newest in information technology, the National Aeronautics and Space Administration (NASA) has launched an intensive effort to link lessons learned with specific technical standards through various Internet databases. This article will discuss the importance of lessons learned to engineers, the difficulty in finding relevant lessons learned while engaged in an engineering project, and the new NASA project that can help alleviate this difficulty. The article will conclude with recommendations for more expanded cross-sectoral uses of lessons learned with reference to technical standards.

Gill, Paul↗