Search NASA⌕ Search

SEARCH · Search NASA

Results for “in situ processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A single-Pt-atom-on-Ru-nanoparticle electrocatalyst for CO-resilient methanol oxidation

Single Pt atom catalysts are key targets because a high exposure of Pt substantially enhances electrocatalytic activity. In addition, PtRu alloy nanoparticles are the most active catalysts for the methanol oxidation reaction. To combine the exceptional activity of single Pt atom catalysts with an active Ru support we must overcome the synthetic challenge of forming single Pt atoms on noble metal nanoparticles. In this report we demonstrate a process that grows and spreads Pt islands on Ru branched nanoparticles to create single-Pt-atom-on-Ru catalysts. By following the spreading process by in situ TEM, we found that the formation of a stable single atom structure is thermodynamically driven by the formation of strong Pt–Ru bonds and the lowering of the surface energy of the Pt islands. The stability of the single-Pt-atom-on-Ru structure and its resilience to CO poisoning result in a high current density and mass activity for the methanol oxidation reaction over time.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High n -type conductivity and carrier concentration in Si-implanted homoepitaxial AlN

We demonstrate Si-implanted AlN with high conductivity (>1 Ω -1 cm -1 ) and high carrier concentration (5 × 101 8 cm -3 ). This was enabled by Si implantation into AlN with a low threading dislocation density (TDD) (<10 3 cm -2 ), a non-equilibrium damage recovery and dopant activation annealing process, and in situ suppression of self-compensation during the annealing. Low TDD and active suppression of V Al -nSi Al complexes via defect quasi Fermi level control enabled low compensation, while low-temperature, non-equilibrium annealing maintained the desired shallow donor state with an ionization energy of ~70 meV. The realized n-type conductivity and carrier concentration are over one order of magnitude higher than that reported thus far and present a major technological breakthrough in doping of AlN.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Cinematic reflectometry using QIKR, the quite intense kinetics reflectometer

The Quite Intense Kinetics Reflectometer (QIKR) will be a general-purpose, horizontal-sample-surface neutron reflectometer. Reflectometers measure the proportion of an incident probe beam reflected from a surface as a function of wavevector (momentum) transfer to infer the distribution and composition of matter near an interface. The unique scattering properties of neutrons make this technique especially useful in the study of soft matter, biomaterials, and materials used in energy storage. Exploiting the increased brilliance of the Spallation Neutron Source Second Target Station, QIKR will collect specular and off-specular reflectivity data faster than the best existing such machines. It will often be possible to collect complete specular reflectivity curves using a single instrument setting, enabling “cinematic” operation, wherein the user turns on the instrument and “films” the sample. Samples in time-dependent environments (e.g., temperature, electrochemical, or undergoing chemical alteration) will be observed in real time, in favorable cases with frame rates as fast as 1 Hz. Cinematic data acquisition promises to make time-dependent measurements routine, with time resolution specified during post-experiment data analysis. This capability will be deployed to observe such processes as in situ polymer diffusion, battery electrode charge–discharge cycles, hysteresis loops, and membrane protein insertion into lipid layers.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Analytical capabilities for iodine detection: Review of possibilities for different applications

This Review summarizes a range of analytical techniques that can be used to detect, quantify, and/or distinguish between isotopes of iodine (e.g., long-lived 129 I, short-lived 131 I, stable 127 I). One reason this is of interest is that understanding potential radioiodine release from nuclear processes is crucial to prevent environmental contamination and to protect human health as it can incorporate into the thyroid leading to cancer. It is also of interest for evaluating iodine retention performances of next-generation iodine off-gas capture materials and long-term waste forms for immobilizing radioiodine for disposal in geologic repositories. Depending upon the form of iodine (e.g., molecules, elemental, and ionic) and the matter state (i.e., solid, liquid, and gaseous), the available options can vary. In addition, several other key parameters vary between the methods discussed herein, including the destructive vs nondestructive nature of the measurement process (including in situ vs ex situ measurement options), the analytical data collection times, and the amount of sample required for analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Vapor-phase grafting of functional silanes on atomic layer deposited Al 2 O 3

Fundamental studies are needed to advance our understanding of selective adsorption in aqueous environments and develop more effective sorbents and filters for water treatment. Vapor-phase grafting of functional silanes is an effective method to prepare well-defined surfaces to study selective adsorption. In this investigation, we perform vapor phase grafting of five different silane compounds on aluminum oxide (Al2O3) surfaces prepared by atomic layer deposition. These silane compounds have the general formula L3Si–C3H6–X where the ligand, L, controls the reactivity with the hydroxylated Al2O3 surface and the functional moiety, X, dictates the surface properties of the grafted layer. We study the grafting process using in situ Fourier transform infrared spectroscopy and ex situ x-ray photoelectron spectroscopy measurements, and we characterize the surfaces using scanning electron microscopy, atomic force microscopy, and water contact angle measurements. Here, we found that the structure and density of grafted aminosilanes are influenced by their chemical reactivity and steric constraints around the silicon atom as well as by the nature of the anchoring functional groups. Methyl substituted aminosilanes yielded more hydrophobic surfaces with a higher surface density at higher grafting temperatures. Thiol and nitrile terminated silanes were also studied and compared to the aminosilane terminated surfaces. Uniform monolayer coatings were observed for ethoxy-based silanes, but chlorosilanes exhibited nonuniform coatings as verified by atomic force microscopy measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Programming Function via Soft Materials (PFvSM) (Final Report)

The PFvSM cluster at the University of Illinois greatly deepened the science of soft materials and expanded the means for embedding within them unprecedented functionalities. We pioneered a mesoscopic approach to materials design that combined leading competencies in fundamental experimental and theoretical soft matter science and fabrication that powerfully establishes equilibrium and nonequilibrium assembly of novel and complex building blocks as a preeminent contributor to progress in materials chemistry. Our cluster’s vision was an integrated program of work centered on soft matter science with the ultimate goal of impacting important energy technologies. As elementary units we employed function-encoded colloids, nanoparticles, large mesh fibrillar gels, deterministically fabricated networks and hybrid objects. These materials were employed as building blocks for diverse model systems that allowed fundamental soft matter principles of wide relevance to be established. Their assembly into materials with useful functional behavior provided new approaches to challenging problems in basic energy science including energy harvesting, transport and storage. To achieve these goals the cluster brought together a team of recognized world-leaders in materials synthesis and processing, in-situ characterization, theory and modeling, and materials design, integration and fabrication

36 MATERIALS SCIENCE↗
DOE OSTI2022

Pele: An Exascale-Ready Suite of Combustion Codes

High fidelity simulations of realistic combustion devices are extremely demanding computationally because of the requirements to capture complex fuel chemical decomposition, its intricate interactions with turbulent, often multiphase, flows, and the wide separation of space and time scales between the thin flame and the device boundaries. Software required to carry out such computations tends to be extremely complex, particularly when designed to exploit hardware accelerators, and can be difficult to port and maintain. We present Pele, a performance portable suite of tools for the simulation of combustion systems, including codes to evolve reactive multiphase configurations in the low Mach number and compressible flow regimes, along with a set of inter-compatible post processing and in situ analysis tools. The Pele suite of tools is built on top of the AMReX framework for block-structured adaptive mesh refinement, which provides efficient data structures and algorithms that enable the development of a wide variety of efficient mesh and particle based PDE integration schemes. A hierarchical MPI+X parallelism scheme supports CPU-only and accelerated architectures, where X can be OpenMP, CUDA, and HIP based approaches for intra-node computational work distribution. The algorithms and data structures underlying the Pele simulation and analysis tools are highly scalable and performant across a wide variety of high-performance computing platforms, including DOEs newest exascale-class machines, Frontier and Aurora. The simulation and analysis tools are fully documented and freely distributed as open source via GitHub. We present key algorithmic and software challenges, solution strategies, performance and resulting set of capabilities.

AMReX↗
DOE OSTI2025

Spatial mapping of dissolved methane using an in situ sensor in Puget Sound

Release of methane, as gas bubbles or in the dissolved phase, from the seafloor has been observed in coastal waters (< 200 m) and deep ocean basins (> 1000 m). Methane dissolution within the water column affects the geochemistry of the surrounding water, leading to localized oxygen loss and potential escape to the atmosphere, particularly from shallower sites. Traditional methods for detecting and quantifying dissolved methane rely on collecting discrete water samples for ship- or land-based ex situ analysis and post processing. Here, we report on the use of a reduced response time, in situ methane sensor, the Sensor for Aqueous Gases in the Environment (SAGE), for detecting and quantifying dissolved methane concentrations in a wide range of seafloor environments. During a Fall 2022 research cruise on the R/V Thomas G. Thompson in Puget Sound, SAGE was integrated onto a towed conductivity/temperature/depth rosette and deep-sea camera system with live-stream 1 Hz telemetry and used to spatially map the concentration of methane approximately 1 m above the seafloor. The site had been previously identified as an active methane plume field characterized by gas bubbles, fluid venting, and a faulted seabed. The widespread background dissolved concentration of methane measured by SAGE was 83 nM, and a range of 78–670 nM was observed throughout the survey. The results highlight the capacity of SAGE to map the spatial and temporal variability of dissolved methane concentrations in situ and to identify and localize sites of variable methane emissions from the seafloor.

Padilla, Alexandra M. [Woods Hole Oceanographic In↗
DOE OSTI2021

Absorption of Nitrogen during Pulsed Wave L-PBF of 17-4 PH Steel

In the fabrication of 17-4 PH by laser powder bed fusion (L-PBF) the well-documented occurrence of large amounts of retained austenite can be attributed to an elevated concentration of nitrogen present in the material. While the effects of continuous wave (CW) laser processing on in-situ nitrogen absorption characteristics have been evaluated, power modulated pulsed wave (PW) laser processing effects have not. In this study the effects of PW L-PBF processing of 17-4 PH on nitrogen absorption, phase composition, and mechanical performance are explored using commercially available PW L-PBF equipment and compared to samples produced by CW L-PBF. PW L-PBF samples fabricated in cover gas conditions with varying amounts of nitrogen demonstrated reduced absorption levels compared to those produced by CW L-PBF with no effects on phase composition and minimal effects on mechanical performance.

17-4 PH↗
DOE OSTI2021

Supply Chain Sustainability Analysis of Renewable Hydrocarbon Fuels via Indirect Liquefaction, Ex Situ Catalytic Fast Pyrolysis, Hydrothermal Liquefaction, Combined Algal Processing, and Biochemical Conversion: Update of the 2020 State-of-Technology Cases

The Department of Energy’s (DOE) Bioenergy Technologies Office (BETO) aims to develop and deploy technologies to transform renewable biomass resources into commercially viable, high-performance biofuels, bioproducts, and biopower through public and private partnerships (U.S. Department of Energy, 2016). BETO and its national laboratory teams conduct in-depth techno-economic assessments (TEA) of biomass feedstock supply and logistics and conversion technologies to produce biofuels. There are two general types of TEAs: A design case outlines a target case (future projection) for a particular biofuel pathway. It enables identification of data gaps and research and development needs and provides goals and benchmarks against which technology progress is assessed. A state of technology (SOT) analysis assesses progress within and across relevant technology areas based on actual results at current experimental scales relative to technical targets and cost goals from design cases, and includes technical, economic, and environmental criteria as available. In addition to developing a TEA for a pathway of interest, BETO also performs a supply chain sustainability analysis (SCSA). The SCSA takes the life-cycle analysis approach that BETO has been supporting for about 20 years. It enables BETO to identify energy consumption, environmental, and sustainability issues that may be associated with biofuel production. Approaches to mitigate these issues can then be developed. Additionally, the SCSA allows for comparison of energy and environmental impacts across biofuel pathways in BETO’s research and development portfolio. This technical report describes the SCSAs for the production of renewable hydrocarbon transportation fuels via a range of conversion technologies in the 2020 SOTs: (1) renewable high octane gasoline (HOG) via indirect liquefaction (IDL) of woody lignocellulosic biomass (note that the IDL pathway in this SCSA represents the syngas conversion design [Harris et al. 2021]); (2) renewable gasoline (RG) and diesel (RD) blendstocks via ex situ catalytic fast pyrolysis of woody lignocellulosic biomass [Abhijit et al. 2021]; (3) RD via hydrothermal liquefaction (HTL) of wet sludge from a wastewater treatment plant; (4) renewable hydrocarbon fuels via biochemical conversion of herbaceous lignocellulosic biomass (Davis et al. 2021; Lin et al. 2021); (5) renewable diesel via HTL of a blend of algae (Davis and Klein, 2021) and woody biomass (Hartley et al. 2020); and (6) renewable diesel via combined algae processing (CAP) (Wiatrowski and Davis, 2021). This technical report focuses on the environmental performance of these six biofuel production pathways in their 2020 SOT cases. The results of these renewable hydrocarbon fuel pathways in these SCSA analyses update those for the respective 2019 SOT cases (Cai et al. 2020). They also provide an opportunity to examine the impact of technology improvements in both biomass feedstock production and biofuel production that have been achieved in 2020 SOTs on the sustainability performance of these renewable transportation fuels. The SCSA results also reflect updates to Argonne National Laboratory’s Greenhouse gases, Regulated Emissions, and Energy use in Technologies (GREET®) model, which was released in October 2020 (Wang et al. 2020). These GREET updates include the production of natural gas, electricity, and petroleum-based fuels that can influence biofuels’ supply chain greenhouse gas (GHG) (CO 2 , CH 4 , and N 2 O) emissions, water consumption, and air pollutant emissions. GHG emissions, water consumption, and nitrogen oxides (NO x ) emissions are the main sustainability metrics assessed in this analysis. In this analysis, we define water consumption as the amount of water withdrawn from a freshwater source that is not returned (or returnable) to a freshwater source at the same level of quality. Life-cycle fossil energy consumption and net energy balance, which is the life-cycle fossil energy consumption deducted from the renewable biofuel energy produced, are also assessed.

09 BIOMASS FUELS↗
DOE OSTI2026

Establishing an acoustic-property relationship in laser powder bed fusion with machine learning

Quality control of Laser Powder Bed Fusion (PBF-LB) additively manufactured parts is an important hurdle inhibiting the technology’s use structural applications. Acoustic monitoring of the laser powder bed fusion process can detect defects in-situ that are known to degrade mechanical properties. However, processing-structure-property (PSP) relationships are required to extrapolate from detected defects to part performance. Here, this study explores how acoustics may be a suitable signature linking processing conditions to properties, thus effectively substituting for structure in the PSP relationship. Establishing such a relationship would enable a part’s mechanical performance to be directly predicted from its acoustic signature, reducing the need for destructive testing or microstructural analysis to ensure a part will meet performance requirements. One hundred CoCrFeMnNi high entropy alloy tensile bars were printed across 13 process conditions in a series of 6 prints. The acoustic signatures of these tensile bars were used to train machine learning models to predict each part’s mechanical properties. By using both process information and acoustic information to predict mechanical properties, yield strength was predicted 18% more accurately and ductility to failure was predicted 10% more accurately than is achieved when using duplicate parts to predict part performance. Finally, individual acoustic frequencies were investigated to determine why acoustic signatures improve mechanical property predictions and the potential physical origins of these signatures. This work demonstrates how blending acoustics, process information, and machine learning can provide in-situ diagnostics of mechanical properties and improve the reliability of the PBF-LB process.

Acoustic emission↗
DOE OSTI2022

Monitoring and flaw detection during wire-based directed energy deposition using in-situ acoustic sensing and wavelet graph signal analysis

The goal of this work is to detect flaw formation in the wire-based directed energy deposition (W-DED) process using in-situ sensor data. The W-DED studied in this work is analogous to metal inert gas electric arc welding. The adoption of W-DED in industry is limited because the process is susceptible to stochastic and environmental disturbances that cause instabilities in the electric arc, eventually leading to flaw formation, such as porosity and suboptimal geometric integrity. Moreover, due to the large size of W-DED parts, it is difficult to detect flaws post-process using non-destructive techniques, such as X-ray computed tomography. Accordingly, the objective of this work is to detect flaw formation in W-DED parts using data acquired from an acoustic (sound) sensor installed near the electric arc. To realize this objective, we develop and apply a novel wavelet integrated graph theory approach. The approach extracts a single feature called graph Laplacian Fiedler number from the noise-contaminated acoustic sensor data, which is subsequently tracked in a statistical control chart. Using this approach, the onset of various types of flaws are detected with a false alarm rate less-than 2%. This work demonstrates the potential of using advanced data analytics for in-situ monitoring of W-DED.

42 ENGINEERING↗
DOE OSTI2022

Development of a co-anneal process for double-side TOPCon precursor fabricated by ex-situ POCI3 and APCVD boron diffusion

The aim of this study was to develop a simple and industrially attractive co-anneal process to fabricate a high-quality DS-TOPCon precursor with textured n-TOPCon on front and planar p- TOPCon on rear by ex-situ POCI3 and APCVD boron diffusion. This requires only one high temperature anneal with no additional masking steps. Excellent iVOC of 733mV and iFF of ~86% were achieved after SiNX passivation on both sides, prior to contact firing. Our device modeling projects that this precursor in combination with a manufacturing-friendly poly-Si patterning technique on front can enable> 25% DS-TOPCon cells at low-cost.

APCVD↗