Search NASA⌕ Search

SEARCH · Search NASA

Results for “laminates”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

A Micromechanics-Based Damage Model for the Strength Prediction of Composite Laminates

A new damage model based on a micromechanical analysis of cracked [+/-0deg/90deg(sub n)]s laminates subjected to multiaxial loads is proposed. The model predicts the onset and accumulation of transverse matrix cracks in uniformly stressed laminates, the effect of matrix cracks on the stiffness of the laminate, as well as the ultimate failure of the laminate. The model also accounts for the effect of the ply thickness on the ply strength. Predictions relating the elastic properties of several laminates and multiaxial loads are presented.

Camanho, Pedro P.↗

Determination of the Shear Stress Distribution in a Laminate from the Applied Shear Resultant--A Simplified Shear Solution

The simplified shear solution method is presented for approximating the through-thickness shear stress distribution within a composite laminate based on laminated beam theory. The method does not consider the solution of a particular boundary value problem, rather it requires only knowledge of the global shear loading, geometry, and material properties of the laminate or panel. It is thus analogous to lamination theory in that ply level stresses can be efficiently determined from global load resultants (as determined, for instance, by finite element analysis) at a given location in a structure and used to evaluate the margin of safety on a ply by ply basis. The simplified shear solution stress distribution is zero at free surfaces, continuous at ply boundaries, and integrates to the applied shear load. Comparisons to existing theories are made for a variety of laminates, and design examples are provided illustrating the use of the method for determining through-thickness shear stress margins in several types of composite panels and in the context of a finite element structural analysis.

Bednarcyk, Brett A.↗

Bounds on Flexural Properties and Buckling Response for Symmetrically Laminated Plates

Nondimensional parameters and equations governing the buckling behavior of rectangular symmetrically laminated plates are presented that can be used to represent the buckling resistance, for plates made of all known structural materials, in a very general, insightful, and encompassing manner. In addition, these parameters can be used to assess the degree of plate orthotropy, to assess the importance of anisotropy that couples bending and twisting deformations, and to characterize quasi-isotropic laminates quantitatively. Bounds for these nondimensional parameters are also presented that are based on thermodynamics and practical laminate construction considerations. These bounds provides insight into potential gains in buckling resistance through laminate tailoring and composite-material development. As an illustration of this point, upper bounds on the buckling resistance of long rectangular orthotropic plates with simply supported or clamped edges and subjected to uniform axial compression, uniform shear, or pure inplane bending loads are presented. The results indicate that the maximum gain in buckling resistance for tailored orthotropic laminates, with respect to the corresponding isotropic plate, is in the range of 26-36% for plates with simply supported edges, irrespective of the loading conditions. For the plates with clamped edges, the corresponding gains in buckling resistance are in the range of 9-12% for plates subjected to compression or pure inplane bending loads and potentially up to 30% for plates subjected to shear loads.

Weaver, Paul M.↗

Modeling the Non-Linear Response of Fiber-Reinforced Laminates Using a Combined Damage/Plasticity Model

The present work is concerned with modeling the non-linear response of fiber reinforced polymer laminates. Recent experimental data suggests that the non-linearity is not only caused by matrix cracking but also by matrix plasticity due to shear stresses. To capture the effects of those two mechanisms, a model combining a plasticity formulation with continuum damage has been developed to simulate the non-linear response of laminates under plane stress states. The model is used to compare the predicted behavior of various laminate lay-ups to experimental data from the literature by looking at the degradation of axial modulus and Poisson s ratio of the laminates. The influence of residual curing stresses and in-situ effect on the predicted response is also investigated. It is shown that predictions of the combined damage/plasticity model, in general, correlate well with the experimental data. The test data shows that there are two different mechanisms that can have opposite effects on the degradation of the laminate Poisson s ratio which is captured correctly by the damage/plasticity model. Residual curing stresses are found to have a minor influence on the predicted response for the cases considered here. Some open questions remain regarding the prediction of damage onset.

Schuecker, Clara↗

Analytical Modelling of Transverse Matrix Cracking of [plus or minus Theta/90(sub n)](sub s) Composite Laminates Under Multiaxial Loading

An analytical model based on the analysis of a cracked unit cell of a composite laminate subjected to multiaxial loads is proposed to predict the onset and accumulation of transverse matrix cracks in the 90(sub n) plies of uniformly stressed [plus or minus Theta/90(sub n)](sub s) laminates. The model predicts the effect of matrix cracks on the stiffness of the laminate, as well as the ultimate failure of the laminate, and it accounts for the effect of the ply thickness on the ply strength. Several examples describing the predictions of laminate response, from damage onset up to final failure under both uniaxial and multiaxial loads, are presented.

Mayugo, J A.↗

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗

Stationary turbine component with laminated skin

A stationary turbine engine component, such as a turbine vane, includes a internal spar and an external skin. The internal spar is made of a plurality of spar laminates, and the external skin is made of a plurality of skin laminates. The plurality of skin laminates interlockingly engage the plurality of spar laminates such that the external skin is located and held in place. This arrangement allows alternative high temperature materials to be used on turbine engine components in areas where their properties are needed without having to make the entire component out of such material. Thus, the manufacturing difficulties associated with making an entire component of such a material and the attendant high costs are avoided. The skin laminates can be made of advanced generation single crystal superalloys, intermetallics and refractory alloys.

42 ENGINEERING↗

Impact of Insulation Strategies of Cross-Laminated Timber Assemblies on Energy Use, Peak Demand, and Carbon Emissions

Cross-Laminated Timber (CLT) panels have many structural benefits but do not have much thermal resistance. We have developed a solution to insulate CLT structures that uses high-performance insulation panels that provide R-values up to R40/inch. The CLT panels are made of layers of wood laminates (three, five, seven or more). The solution replaces some of the wood laminates in the CLT production with the insulation panels in a staggered fashion so that the wood laminates maintain contact throughout the panel, ensuring the CLT panel’s structural integrity. The insulated CLT panels have factory-installed water-resistive barriers reducing the installation time by eliminating installing insulation and water-resistive barriers on site. Per simulations, the CLT/insulation panel achieved code-required insulation levels with commonly available insulation materials. The significance of the thermal mass of CLT/insulation hybrid building envelopes was quantified by comparing the whole building energy performance and peak demand of traditional low mass and CLT wall assemblies resulting in up to 7% reduction in peak demand for cooling in Knoxville, TN, in a multifamily building. Buildings contribute over 40 percent of carbon emissions. The proposed CLT/insulation hybrid building envelope addresses both operational and embodied carbon by having high thermal resistances due to the embedded insulation sections and eliminating the use of high embodied carbon materials such as steel and concrete. The carbon benefit is estimated.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Some Torsional-damping Measurements of Laminated Beams as Applied to the Propeller Stall-flutter Problem

The structural damping in the torsion mode of vibration of a series of untwisted, laminated thin beams simulating propeller blades is presented. The number of lamination were varied, as well as the bonding material and the method of joining lamination. Application of the data to the calculation of the minimum flutter speed of thin propeller blades indicates that appreciable gains in the minimum flutter speed may be obtained for laminated blades using a Cycleweld bond.

ADHESIVES↗

Effect of Anisotropy on Microstructures and Mechanical Properties of Rolled Ti/Al/Mg/Al/Ti Laminates

TA2/5052Al/AZ31/5052Al/TA2 five-ply laminates were fabricated by hot rolling, and the effect of anisotropy on their microstructures and mechanical properties was studied. After rolling, the Mg/Al and Al/Ti interfaces were both closely connected, but the interfacial shapes were totally different. For the Mg layer microstructures in the middle area, regardless of the direction, dynamic recrystallized (DRXed) grains appeared around the deformation bands. However, twins and a shear zone appeared in the RD sample; the twins decreased in the sample along the 45° angle, and no twins appeared in the TD sample. The Ti layer showed equiaxed grains in different directions, which were attributed to the ability of Ti alloy to anti-deform. The tensile testing results showed that the fracture of the Ti/Al/Mg/Al/Ti laminates can be divided into four stages. The laminate had an ultimate tensile strength of 434 MPa and excellent elongation along the rolling direction (RD), which were attributed to its DRXed grains and twins. In conclusion, the laminates had significant anisotropy due to the presence of Mg alloys.

36 MATERIALS SCIENCE↗

Structures of the lamin A/C R335W and E347K mutants: Implications for dilated cardiolaminopathies

Highlights: Black-Right-Pointing-Pointer Defects in the Lamin AC gene have been linked to more than 10 laminopathies. Black-Right-Pointing-Pointer R335 and E347 are highly conserved residues, whose mutation preserves Coil2B 3D structure. Black-Right-Pointing-Pointer R335W and E347K mutations may affect LMNA interaction with proteins of nuclear lamina. -- Abstract: Dilated cardiomyopathy (DCM) is a condition whereby the normal muscular function of the myocardium is altered by specific or multiple aetiologies. About 25-35% of DCM patients show familial forms of the disease, with most mutations affecting genes encoding cytoskeletal proteins. Most of the DCM-related mutations fall in the Lamin AC gene, in particular in the Coil2B domain of the encoded protein. In this context, we focussed our studies on the crystal structures of two lamin Coil2B domain mutants (R335W and E347K). Both R335 and E347 are higly conserved residues whose substitution has little effects on the Coil2B domain three-dimensional structure; we can thus hypothesize that the mutations may interfere with the binding of components within the nuclear lamina, or of nuclear factors, that have been proposed to interact/associate with lamin A/C.

60 APPLIED LIFE SCIENCES↗

Analysis of a hybrid balanced laminate as a structural material for thick composite beams with axial stiffeners

An accurate stress analysis has been carried out to investigate the suitability of a hybrid balanced laminate as a structural material for thick composite beams with axial stiffeners. Three different balanced laminates composed of dissimilar ply material as well as fiber orientations are considered for a thick beam on simple supports with stiffened lateral ends. A displacement potential based elasticity approach is used to obtain the numerical solution of the corresponding elastic fields. The overall laminate stresses as well as individual ply stresses are analysed mainly in the perspective of laminate hybridization. Both the fiber material and ply angle of individual laminas are found to play dominant roles in defining the design stresses of the present composite beam.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Investigating the Effect of Lamination on FAMACs: Toward a New Phase Space of Perovskite Solar Cell Fabrication

The rapid progress in the field of perovskite solar cells has led to efficiencies approaching that of crystalline silicon in single junction devices, and increasing emphasis is now being placed on scalable fabrication strategies that have the potential to truly impact the photovoltaics industry. The standard fabrication route of sequential, layer-bylayer depositions to form the device stack is limited by the small range of selective materials that can withstand successive solvent exposures and thermal annealings. In order to overcome this limitation, we have developed a method to fabricate the device stacks through mechanical lamination under moderate pressures and temperatures. The procedure involves fabricating two transparent conductive oxide/transport material/perovskite half stacks and laminating them together at the perovskite/perovskite interface. This procedure previously achieved 10% efficiency in initial attempts based on methyl ammonium lead iodide (MAPI) perovskite compositions. Herein, we reported the fabrication conditions to achieve a reproducible lamination with a complex, multi-cation perovskite, [Cs0.05(MA0.17F A0.83)0.95P b(I0.83Br0.17)3] (FAMACs), laminated at 18 degrees C and with a pressure of 350 psi for 30 minutes. The resulting material showed a sharpening of the optical absorption edge and a slight reduction in the band gap from 1.622 eV to 1.616 eV, indicative of improved ordering and reduced defects. Concurrently, time resolved photoluminescence measurements revealed an increased luminescence lifetime from 85 ns to 123 ns.

14 SOLAR ENERGY↗

Evaluation of laminated aluminum plate for shuttle applications

Flaw growth behavior in roll diffusion bonded and adhesive bonded 2219-T87 aluminum alloy was compared to that in monolothic 2219-T87. Based on tests at 40 KSI cyclic stress, for equivalent cyclic life, a .004 interlayer laminate can tolerate a surface flaw twice as wide as in monolithic material, or provide an 8% weight saving by operating at higher stress for the same initial flaw. Roll diffusion bonded material with three structural plies of 2219-T87 and two interlayers of 1100 aluminum was prepared with interlayer thicknesses of .004, .007 and .010 in. Total laminate thickness was .130 in. The .004 interlayer laminate was most effective and gave better results than monolithic material at 40 and 48 ksi. Adhesive bonded specimens were fabricated of three sheets of 2219-T87 aluminum alloy bonded with METLBOND 329 adhesive. Adhesive bonded specimens gave longer lives to failure than diffusion bonded specimens at 40 ksi the diffusion bonded material was superior. Flaws initiated in one ply of the laminate grew to the edges of the specimen in that ply but did not propagate into adjacent plies.

Martin, M. J.↗

Design, fabrication, testing and delivery of a feasibility model laminated ferrite memory

The effect of using multiword addressing with laminated ferrite arrays was made. Both a reduction in the number of components, and a reduction in power consumption was obtained for memory capacities between one million bits and one million words. An investigation into the effect of variations in the processing steps resulted in a number of process modifications that improved the quality of the arrays. A feasibility model laminated ferrite memory system was constructed by modifying a commercial plated wire memory system to operate with laminated ferrite arrays. To provide flexibility for the testing of the laminated ferrite memory, an exerciser has been constructed to automatically control the loading and recirculation of arbitrary size checkerboard patterns of one's and zero's and to display the patterns of stored information on a CRT screen.

Heckler, H. C.↗

Method for estimating fracture strength of specially orthotropic composite laminates.

A method is presented for estimating the stress intensity factor characteristic of crack extension in a specially orthotropic advanced fiber composite laminate, based on the elastic properties and ultimate principal strengths of a lamina, the laminate construction, and the experimentally determined value of the characteristic stress intensity factor of an arbitrary angle-plied, midplane symmetric laminate. A comparison of the results obtained from this method with limited experimental data for graphite/epoxy laminates indicates that the method is quite accurate for this particular material system. The predictive method is also used, in conjunction with experimental data, to estimate the size of a damage zone surrounding the crack tip.

Konish, H. J., Jr.↗

Analysis of laminated, composite, circular cylindrical shells with general boundary conditions

This report develops: (1) a refined approximate theory for the static and dynamic analyses of finite, laminated, composite, circular cylindrical shells with general boundary conditions; (2) an exact three-dimensional analysis of simply supported, laminated, composite, circular cylindrical shells, and (3) a thin-shell theory for laminated, composite, circular cylindrical shells. In the refined approximate theory the displacements are assumed piecewise linear across the thickness and the effects of transverse shear deformations and transverse normal stress are included. A variational approach is followed to obtain the governing differential equations and boundary conditions. A general solution of the governing differential equations is also presented. The results obtained by using the refined approximate theory and the thin-shell theory are compared with the exact results for the case of free vibrations of simply supported, laminated, composite, circular cylindrical shells. The refined approximate theory is very accurate, even for thick shells with short nodal distances, whereas thin-shell theory is reasonably accurate only for thin shells at moderate nodal distances and wave number less than 2.

Srinivas, S.↗