Search NASA⌕ Search

SEARCH · Search NASA

Results for “lamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mitigation and Diagnosis of Pin-Hole Formation in Polymer Electrolyte Membrane Fuel Cells

In this work, we implement a calendering technique to flatten stray fibers within the gas diffusion media, thereby mitigating pin-hole formation in the hot-pressed MEAs. We have investigated the influence of calendering on the long-term durability for several types of gas diffusion electrodes (GDEs) using a combined chemical and mechanical accelerated stress test (AST). The calendered MEAs demonstrate an average AST lifetime improvement of 77% relative to the as-fabricated MEAs.

AMR↗
DOE OSTI2024

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗
DOE OSTI2025

Additive manufacturing of metal matrix composites

Although Metal matrix composites (MMCs) are superior to most sought-after metallic alloys, their challenging fabricability has limited their widespread use in bulk-form applications. Among the many advanced fabrication techniques, Additive Manufacturing (AM), owing to its unique capabilities to produce near-net shapes, has drawn significant traction in the past two decades, especially for materials that are difficult to process using traditional methods. However, unlike pure metal/alloy systems, MMCs are highly sensitive to the processing conditions prevailing in AM techniques due to factors such as the high melting point of reinforcement particles and the potential for in-situ reactions. Therefore, it may be a while before metal matrix composites are commercially produced via AM. This review will discuss the current state-of-the-art design, fabricability, and performance of various additively manufactured MMCs. A particular focus will be on microstructural evolution and microstructure-property relationships. The most employed AM techniques, such as directed energy deposition, powder bed fusion, binder jetting, sheet lamination, and solid-state friction stir processing, are fundamentally different in terms of thermo-kinetics, forming the perspective for this review. A detailed comparison of microstructural evolution and process parameter optimization, including feedstock preparation methods and the role of machine learning and modeling among the different AM processes, is also presented. Finally, a critical evaluation of emerging AM technologies for MMCs is also provided, highlighting their potential advantages and challenges.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Analysis of electrically conductive adhesives in shingled solar modules by X-ray imaging techniques

The failure mechanisms of electrically conductive adhesives (ECAs) in solar modules are difficult to study since the ECA layer is not easily accessible within the module package. In this work, we present two complementary imaging modalities—X-ray radiography and X-ray microcomputed tomography (XCT)—that reveal important morphological features of the ECA within a shingled module. X-ray radiography uses single X-ray projections to provide fast and non-destructive imaging of the shingled interconnection, illuminating the alignment of the ECA relative to the busbars, the size and shape of the ECA, and the presence of voids within it. Through X-ray radiography, we observed, for example, that the average void coverage area of ECA segments reduced from 36.7% to 4.4% when an ECA was cured for 60 s prior to module lamination. XCT is a three-dimensional imaging technique that can identify regions in which the ECA makes electrical contact to busbars on cells and regions in which the ECA has cracked, among other features. XCT can also be used to image the individual metal particles within ECA, from which the metal volume fraction of an ECA was found here to be 70.4%. This is a quantity that is not often reported by ECA manufacturers but is important to ensure isotropic conduction. As X-ray projections can be performed non-destructively on full modules, the technique may be used to pinpoint ECA failures in accelerated degradation testing. XCT is complementary and is suited to forensic analysis of failing modules.

14 SOLAR ENERGY↗
DOE OSTI2022

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tensile behavior of diffusion bonded AA6061 - AA6061 with variation in cooling method

Hot isostatically pressed AA6061 cladding is an important structural component of the high performance, Zr-laminated U-10Mo monolithic fuel system for the application in research and test reactors. In this study, the mechanical behavior of two diffusion bonded aluminum alloy, AA6061, was examined using tensile testing. Solid-to-solid diffusion bonding between two pieces of AA6061 was performed by isothermal annealing at 560 °C for 1.5 h, and diffusion couples were subsequently cooled via three different cooling methods: furnace cooling, air cooling, and water quenching. Dog-bone shaped tensile specimens, with 10 mm in gauge length (with diffusion bonded interface in the middle), and 1.5 × 1.5 mm 2 gauge cross-sections, were fabricated from the diffusion bonded AA6061 by electro-discharge machining. Yield strength (% EL at failure) of furnace cooled, air cooled and water quenched tensile specimens determined was 82 ~ 89 MPa (10 ~ 30%), 112 ~ 116 MPa (10 ~ 14%), and 149 ~ 164 MPa (10 ~ 17%), respectively. This variation in mechanical behavior was examined with cooling-rate dependent, concentrated precipitation of Mg 2 Si at the diffusion bonded interface, with due respect for mechanical properties of the AA6061 alloy that inherently vary as a function of cooling rate from 560 °C. Finite element analysis using ABAQUS was employed to augment experimental findings with the appropriate microstructural constituents and alloy properties. Results suggest that the strength is dominated by matrix/bulk properties of AA6061, while ductility is strongly influenced by the cooling method dependent presence of Mg 2 Si precipitates at the interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Sulphur variations in annually layered stalagmites using benchtop micro-XRF

Variation of sulphur in annually laminated stalagmites can be used to infer the impact of past volcanic activities, anthropogenic pollution, and climate change due to increased bushfire activity. The synchrotron radiation micro-X-Ray fluorescence (SR-XRF) microprobe is a powerful tool to analyse and image sulphur recorded in stalagmites with micrometre resolution. However, access to SR-XRF beamlines can be limited, so researchers must select the most promising stalagmites for imaging. Benchtop micro-XRF is an effective tool for trace elemental analysis of speleothem samples and is a candidate for routine laboratory measurement of sulphur along stalagmite laminae and screening for SR-XRF. Here, this study describes a protocol using matrix-matched standards to measure annual variations of sulphur at trace to percent level along the laminae of two Western Australian stalagmites, one of which already having been analysed using SR-XRF. Parameters that affected quantitation include X-ray tube voltage and current, spot size of the X-ray beam and stalagmite surface roughness and porosity. The use of a 20 μm X-ray spot size provides sub-annual spatial resolution that can be completed in an overnight scan. The features in a 1000 point micro-XRF analysis of sulphur along a 20 mm transect show good consistency with SR-XRF microprobe data. Micro-XRF mapping was also performed to produce chemical images on the stalagmite and compared with Raman and X-ray diffraction (XRD) to confirm that the stalagmite is exclusively calcite, with no aragonite, and that the source of sulphur in the samples was gypsum and anhydrite. Regions of very high sulphur in the micro-XRF maps were found to be artefacts due to diffraction of the incident beam but these could be efficiently removed by using a multiple point statistics approach to produce a clean image suitable for analysis of the laminae. This work shows the potential of micro-XRF for routine analysis of sulphur in stalagmites, and to streamline sample characterisation before SR-XRF imaging.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The effect of annealing on kink band formation in Ag/Fe nanolaminates

Kink banding is a common, though not well understood, failure mechanism in anisotropic materials such as nano metallic laminates (NMLs). In this work, we investigate the effect of annealing on kink band (KB) formation in Ag/Fe NMLs prepared by accumulative roll bonding (ARB) using in situ micropillar compression, scanning/transmission electron microscopy (S/TEM), and transmission Kikuchi diffraction (TKD) analyses. Our results show that annealing increases the KB initiation strain, decreases the probability of KB formation, and decreases the load drop magnitude accompanying kink banding in Ag/Fe NMLs. Post-compression analyses reveal that annealing facilitates more uniform deformation of pillars and affects the formation of geometrically necessary grain boundaries (GNBs) near the kink band boundary (KBB). Compared to its as-rolled counterpart, annealed Ag/Fe has wider KBs with blunter KBBs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermomechanical fatigue resistance of low temperature solder for multiwire interconnects in photovoltaic modules

Novel interconnect technologies leveraging low melting temperature solders, such as multiwire interconnects, are being deployed in photovoltaic (PV) modules for improved reliability through interconnect redundancy and lower thermal loads during interconnection and lamination. However, the equivalency of standardized accelerated testing to field conditions has not yet been established for these emerging technologies. In this study, the thermomechanical fatigue resistance of low temperature solder alloys is investigated and compared to that of conventional SnPb to assess the acceleration behavior of these alloys. While InSn is shown to have sufficient thermomechanical fatigue resistance on the order of that of SnPb, these results indicate Sn–Bi alloys may have poor thermomechanical fatigue resistance at field conditions. The results also show that Sn–Bi alloys have thermal cycling acceleration factors of less than one. This indicates that the standardized accelerated thermal cycling test, such as that in IEC 61215, will produce misleading results for Sn–Bi alloys and that unique testing is required for this PV module architecture. Though accelerated thermal cycling may be a meaningful qualification test for SnPb solder joints, these results suggest that mechanical loading may be a more appropriate test for Sn–Bi multiwire interconnects. This is due to the distinct processing and geometry of multiwire interconnects which may allow for mechanical, rather than strictly metallurgical interconnections.

14 SOLAR ENERGY↗
DOE OSTI2023

In-situ determination of moisture- and temperature-driven deflection of an encapsulated Si photovoltaic cell

Module reliability and service lifetime are critical factors in improving photovoltaic system performance and reducing the levelized cost of electricity (LCOE). Soldering and lamination of the cell impart residual stresses that persist over time and superimpose additional loads during operation. This paper demonstrates the use of X-ray Topography (XRT) to image in-situ the dynamic response of a glass/backsheet mini-module upon drying at elevated temperature after saturation at humidity levels compatible with accelerated testing. The local water content in the encapsulant is also determined in-situ over time via Water Reflectometric Detection (WaRD), with diffusion of water in the front (glass side) and rear (backsheet side) resolved. As water diffuses out from the back of the glass/backsheet module, the cell curves towards the backsheet concomitantly. Here we find that the cell edges deflect 40μm out-of-plane with respect to its center while the encapsulant dries, compared to ~100 μm deflection when heating from 25°C to 85°C. The local cell deflections (changes in cell orientation) are correlated with the dynamic loss of water in the backside encapsulant. We conclude that the observed cell deflections are the result of hygroscopic stress induced by the encapsulant upon moisture outdiffusion. Therefore, the cell experiences a continually changing stress state and curvature dependent on local humidity and temperature. Depending on cell architecture and interconnection, this “breathing” mode of the cell may induce wear out and fatigue of the interconnects, affect the electrical connection of cracked pieces or cause failure near the interconnected edges of two cells.

14 SOLAR ENERGY↗
DOE OSTI2023

PV encapsulant formulations and stress test conditions influence dominant degradation mechanisms

Polyethylene-based poly(ethylene-co-vinyl acetate) (EVA), polyolefin elastomer (POE), and thermoplastic polyolefin (TPO) are common polymer candidates for photovoltaic (PV) module encapsulants. The choice of encapsulant must be carefully considered in novel module designs, such as bifacial glass/glass laminates, to limit performance degradation through loss of optical transmittance, mechanical integrity, and corrosion - as well as potential-induced degradation. Encapsulant quality and resilience against environmental stressors are readily influenced by the additives in the encapsulant formulation. Here, we show that, the changes in optical transmittance after UV aging result from the discoloration caused by interactions between additives, and optical scattering from changes in the polymer crystal structure. We observed competing cross-linking and chain scission mechanisms, with their kinetics influenced by the presence of oxygen and elevated temperatures. Increasing chamber temperatures from 55 °C to 85 °C during the UV stress test amplified encapsulant discoloration and promoted polymer cross-linking, causing severe, irreversible damage that remains to be proven field relevant. Damp heat aging was found to be insufficient to produce significant encapsulant degradation; however, combining stress tests sequentially allowed detection of further degradation beyond the limitations of the damp heat test alone. Appropriate degradation screening methods are necessary to uncover potential encapsulant weaknesses.

14 SOLAR ENERGY↗
DOE OSTI2024

Durability enhancement of all-solid-state electrochromic devices by adjusting the charge density ratio between electrochromic and counter electrode layers

Here, owing to an increase in global warming, smart-window devices based on charge-balanced electrochromic devices (ECDs), which exhibit high potential to increase the thermal efficiency of buildings, have gained prominence. However, studies on the fabrication and cycling stability of charge-balanced ECDs are scarce. In this study, WO 3 and NiO x films were deposited on indium-tin-oxide (ITO)-coated glass substrates by reactive direct-current magnetron sputtering, and the deposition time was varied to control the thickness and charge density of the thin films. Subsequently, the NiO x /ITO/glass and WO 3 /ITO/glass substrates were laminated with a Li-based polymeric electrolyte to fabricate all-solid-state ECDs comprising electrochromic (EC) and counter-electrode (CE) layers in charge-density ratios of 12.6, 6.4, 2.3, and 1.1. Changes in the electrochromic properties, device-layer microstructure, crystal structure, and elemental composition of the as-constructed ECDs before and after degradation were investigated to understand the influence of the charge-density ratio of the EC and CE layers on the long-term durability of ECDs. Increasing the charge-density ratio decreased the cycling stability of the device owing to changes in the microstructure and crystal structure of the NiO x layer in the microstructural deep-trap sites. Among all the ECDs, those comprising EC and CE layers with similar charge densities showed the most stable optical modulation and highest long-term durability. Finally, based on the aforementioned results, a degradation mechanism for charge-imbalanced all-solid-state ECDs was proposed. This study is expected to open new frontiers in designing optimal-performance electrochemical devices with a wide variety of potential applications.

14 SOLAR ENERGY↗
DOE OSTI2021

Peridynamic Model for Microballistic Perforation of Multilayer Graphene

The peridynamic theory of solid mechanics is applied to the continuum modeling of the impact of small, high-velocity silica spheres on multilayer graphene targets. The model treats the laminate as a brittle elastic membrane. The material model includes separate failure criteria for the initial rupture of the membrane and for propagating cracks. Material variability is incorporated by assigning random variations in elastic properties within Voronoi cells. Here, the computational model is shown to reproduce the primary aspects of the response observed in experiments, including the growth of a family of radial cracks from the point of impact.

42 ENGINEERING↗
DOE OSTI2021

Roles of miR-204 in retinal development and maintenance

Highlights: • miR-204 plays an important role in the development, maintenance, and diseases of the retina. • Various layers of the retina including RPE express miR-204. • Retinoblastoma, age-related macular degeneration, glaucoma and optic nerve injury are among the most common retinopathies caused by miR-204 dysfunction. • miR-204 target genes are involved in diverse signaling pathways crucial for retinal physiology. The retina is the innermost part of the eye of most vertebrates and it is essential for vision. The development, maintenance, and function of this laminated structure is tightly regulated by numerous genes. Deficiencies in the expression of these genes as well as deregulation of various molecular mechanisms can cause retinopathies and blindness. MicroRNAs (miRNAs) are one of the most important and effective molecular regulatory mechanisms that underlie the biology of the retina. miRNAs have specific functional roles in the development and maintenance of different retinal layers and retinal cell types. While previous studies have reported a large number of miRNAs linked to development, maintenance and diseases of the retina, no comprehensive study has properly discussed and integrated data from these studies. Given the particular importance of miR-204 in retinal biology, we intend to critically discuss the expression and functional significance of this miRNA in the development, maintenance, and pathologies of the retina. Moreover, we explore biological processes through which miR-204 influences retinal pathophysiology. This review highlights the crucial functions of miR-204 in the retina and suggests the putative mechanism of miR-204 action in retinal biology.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Bipolar Membranes for Ion Management in (Photo)Electrochemical Energy Conversion

Conspectus (Photo)electrochemical energy conversion is important in the development of a carbon-neutral energy economy because it can provide a pathway for mitigating the intermittency of renewable energy sources such as wind and solar. In order to operate efficiently, these technologies, which include photoelectrochemical cells, water and CO 2 electrolyzers, fuel cells, and redox flow batteries, require fast charge transfer kinetics at the electrode/electrolyte interface as well as robust ion management in the electrolyte. In conventional electrolyzers and fuel cells, the electrolyte is strongly acidic or basic and ionic current is carried by H + or OH – ions. In contrast, photoelectrodes and electrocatalysts for water splitting are often studied in buffered solutions. The question of ion balance in these systems led us to analyze the polarization losses due to ion concentration gradients in cells that employed various buffer–membrane combinations. Continuously driving the buffer ions across an ionomer membrane not only lowers the buffer capacity of an aqueous electrolyte but also introduces pH gradients that result in significant energy losses. To address the problem, we and other groups have studied the use of reverse-biased bipolar membranes (BPMs) in (photo)electrolytic cells. BPMs consist of an anion exchange layer (AEL) laminated with a cation exchange layer (CEL) and are usually equipped with a catalytic layer in between to accelerate the water dissociation reaction. At the AEL/CEL interface, water dissociates into protons and hydroxide ions, which replenish those consumed at the cathode and anode. Compared to conventional water electrolyzers with proton/anion exchange membranes (PEM/AEM), BPM electrolyzers provide the unique advantage of continuously operating the cathode and anode under different pH conditions, which is desirable when the two electrode reactions have different pH requirements. BPMs also enable the use of buffered electrolytes at pH values that are optimized for electrode stability and product selectivity in applications such as CO 2 electrolysis. Product crossover losses and CO 2 pumping can be dramatically reduced in BPM-based CO 2 electrolyzers, relative to conventional alkaline membranes, by electrostatic repulsion (of anionic products) and electroosmotic drag (for neutral products). BPM-based gas fed CO 2 electrolyzers can achieve high current density, but they suffer from low Faradaic efficiency (FE) due to the acidic local environment of the CEL. This problem can be mitigated by adding an aqueous buffering layer or by creating a weak acid cation exchange film on the CEL face of the membrane. The use of BPMs in fuel cells and redox flow batteries offers some interesting advantages. Configurations with both reverse and forward bias have been studied, but forward bias has been favored due to material compatibility, reaction kinetics, and thermodynamic considerations. The net reaction at the AEL/CEL interface is the acid–base neutralization reaction, which has a high inherent reaction rate constant, but in the BPM is limited to a nanometric space-charge layer and requires efficient catalysis to achieve high current density. Understanding the mechanism of the acid–base neutralization and the opposite process, the water dissociation reaction, will be essential for improving the performance of forward-biased BPMs. In conclusion, this Account reviews our current understanding of the working mechanisms of BPMs and discusses how we can use them to effectively manage ions for various (photo)electrochemical applications.

Yan, Zhifei↗
DOE OSTI2025

Unsteady- and Steady-State Relative Permeability Study with X-ray and Acoustic Monitoring for CO 2 Storage in Deep Saline Aquifers

In this study, we link the multiphase flow measurements with controls of sedimentary structures (e.g., heterogeneity and anisotropy) on relative permeability to variations in ultrasonic velocities for two deep saline aquifer formations (Entrada and Bluff Sandstones) in the San Juan Basin of the Southwestern USA. The rock specimens were extracted from outcrop sites near Durango, CO, USA. They have distinct differences in grain size, cementation composition, and individual chemical amounts, despite both formations being eolian sandstones. We performed a series of unsteady- and steady-state CO 2 -brine relative permeability experiments under capillary-controlled displacement rates. Unsteady-state experiments were conducted at 71 °C and 9.65 MPa; steady-state experiments were conducted at 85 °C and 22.8 MPa and 89 °C and 24.1 MPa for the Bluff and Entrada Sandstones, respectively. During the unsteady experiments, X-ray computed tomography was used to visualize multiphase flow in porous media and quantify saturations during brine drainage under various flow rates. Scan images and saturation profiles indicate that the CO 2 distribution in the pore volume was strongly impacted by the presence of high-angle cross-laminations, heterogeneous rock structure, and direction of bedding orientation. Those factors contribute to dramatic and quick initial breakthroughs and affect the overall saturation dynamics. Steady-state relative permeability tests were conducted at net flow rates of 1 mL/min for both brine drainage and imbibition. During the experimental steps, the CO 2 fractional flow was increased and decreased for both drainage and imbibition scenarios to mimic the front when CO 2 contacts brine and behind the front when brine enters space previously occupied by CO 2 . It was found that compressional velocity decreased, while shear waves slightly increased as brine saturation decreased. The hysteresis effects for the relative permeability and acoustic velocities were distinct. Furthermore, the CO 2 /brine front stability is quantified by applying a mobility ratio approach to spot saturations at which the boundary line between fluids becomes uneven. The results presented in this work can potentially boost the quality and precision of forecasts for the CO 2 storage projects in which the vertical and horizontal core-scale heterogeneity and anisotropy impact the plume migration within host reservoirs.

carbon dioxide (CO2)↗
DOE OSTI2025

Adhesively Bonded Copper and Polyimide for Flexible Printed Circuit Boards: A Data-Driven Degradation Study Under Accelerated Aging

The long-term durability of polyimide laminated adhesive based flexible printed circuit boards (PCBs) is critical to the microelectronics industry. The interface of the adhesive layer binding the polyimide and copper layers is particularly vulnerable since decreased bonding strength can lead to deadhesion, performance loss, and premature device failure. Here, in this study, adhesive-bonded polyimide and copper samples are subjected to 1000 h of damp heat exposure (85 °C/85%RH) to evaluate the impact of moisture and copper inclusion on the adhesive bonding performance. Significant copper diffusion through the adhesive layer is observed, which, combined with moisture uptake, is found to substantially weaken interfacial adhesion in copper-containing samples, thereby reducing device lifetime. Observed surface and bulk material changes are correlated to adhesion strength using the network structural equation modeling (netSEM) approach, resulting in a robust predictive model of performance degradation based on measurable materials properties.

Chemistry↗
DOE OSTI2023

Prelithiation of Lithium Peroxide for Silicon Anode: Achieving a High Activation Rate

The use of lithium peroxide (Li2O2) as a cost-effective low-weight prelithiation cathode additive was successfully demonstrated. Through a series of studies on the chemical stability of Li2O2 and the activation process of Li2O2 on the cathode, we revealed that Li2O2 is more compatible with conventional electrolyte and cathode laminate slurry than lithium oxide. Due to the significantlysmaller size of commercial Li2O2, it can beused directly as a cathode additive. Moreover, the activation of Li2O2 on the cathode leads to the impedance growthof the cathode possibly resulting from the release of dioxygen andevacuation of Li2O2 inside the cathode. Withthe introduction of a new Li2O2 spread-coatingtechnique on the cathode, the capacity loss was suppressed. Si||NMCfull cells using Li2O2 spread-coated cathodedemonstrated a highly promising activation rate of Li2O2 and significantly enhanced specific capacity and cyclingstability compared to the uncoated full cells.

cathode additive↗