SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Anticipated U.S. demands for non-renewable energy and mineral resources exceed domestic supplies essential for economic growth. For the long term changes necessary in the energy supply and demand gap, new technologies and substitute materials as well as legislation and socio-economic strategies are elaborated.
A critical mechanical system in advanced hypersonic engines is the panel-edge seal system that seals gaps between the articulating engine panels and the adjacent engine splitter walls. Significant advancements in seal technology are required to meet the extreme demands placed on the seals, including the simultaneous requirements of low leakage, conformable, high temperature, high pressure, sliding operation. In this investigation, the design, development, analytical and experimental evaluation of a new ceramic wafer seal that shows promise of meeting these demands will be addressed. A high temperature seal test fixture was designed and fabricated to measure static seal leakage performance under engine simulated conditions. Ceramic wafer seal leakage rates are presented for engine-simulated air pressure differentials (up to 100 psi), and temperature (up to 1350 F), sealing both flat and distorted wall conditions, where distortions can be as large as 0.15 inches in only an 18 inch span. Seal leakage rates are low, meeting an industry-established tentative leakage limit for all combinations of temperature, pressure and wall conditions considered. A seal leakage model developed from externally-pressurized gas film bearing theory is also presented. Predicted leakage rates agree favorably with the measured data for nearly all conditions of temperature and pressure. Discrepancies noted at high engine pressure and temperature are attributed to thermally-induced, non-uniform changes in the size and shape of the leakage gap condition. The challenging thermal environment the seal must operate in places considerable demands on the seal concept and material selection. Of the many high temperature materials considered in the design, ceramics were the only materials that met the many challenging seal material design requirements. Of the aluminum oxide, silicon carbide, and silicon nitride ceramics considered in the material ranking scheme developed herein, the silicon nitride class of ceramics ranked the highest because of their high temperature strength; resistance to the intense heating rates; resistance to hydrogen damage; and good structural properties. Baseline seal feasibility has been established through the research conducted in this investigation. Recommendations for future work are also discussed.
Planar RF circuits are used in a wide range of applications from 1 GHz to 300 GHz, including radar, communications, commercial RF test instruments, and remote sensing radiometers. These circuits, however, provide only fixed tuning elements. This lack of adjustability puts severe demands on circuit design procedures and materials parameters. We have developed a novel tuning element which can be incorporated into the design of a planar circuit in order to allow active, post-fabrication tuning by varying the electrical length of a coplanar strip transmission line. It consists of a series of thin plates which can slide in unison along the transmission line, and the size and spacing of the plates are designed to provide a large reflection of RF power over a useful frequency bandwidth. Tests of this structure at 1 GHz to 3 Ghz showed that it produced a reflection coefficient greater than 0.90 over a 20 percent bandwidth. A 2 GHz circuit incorporating this tuning element was also tested to demonstrate practical tuning ranges. This structure can be fabricated for frequencies as high as 1000 GHz using existing micromachining techniques. Many commercial applications can benefit from this micromechanical RF tuning element, as it will aid in extending microwave integrated circuit technology into the high millimeter wave and submillimeter wave bands by easing constraints on circuit technology.
Lunar mining requirements do not appear to be excessively demanding in terms of volume of material processed. It seems clear, however, that the labor-intensive practices that characterize terrestrial mining will not suffice at the low-gravity, hard-vacuum, and inaccessible sites on the Moon. New research efforts are needed in three important areas: (1) to develop high-speed, high-resolution through-rock vision systems that will permit more detailed and efficient mine site investigation and characterization; (2) to investigate the impact of lunar conditions on our ability to convert conventional mining and exploration equipment to lunar prototypes; and (3) to develop telerobotic or fully robotic mining systems for operations on the Moon and other bodies in the inner solar system. Other aspects of lunar site characterization and mining are discussed.
The use of underfill materials is necessary with flip-chip interconnect technology to redistribute stresses due to mismatching coefficients of thermal expansion (CTEs) between dissimilar materials in the overall assembly. Underfills are formulated using organic polymers and possibly inorganic filler materials. There are a few ways to apply the underfills with flip-chip technology. Traditional capillary-flow underfill materials now possess high flow speed and reduced time to cure, but they still require additional processing steps beyond the typical surface-mount technology (SMT) assembly process. Studies were conducted using underfills in a temperature range of -190 to 85 C, which resulted in an increase of reliability by one to two orders of magnitude. Thermal shock of the flip-chip test articles was designed to induce failures at the interconnect sites (-40 to 100 C). The study on the reliability of flip chips using underfills in the extreme temperature region is of significant value for space applications. This technology is considered as an enabling technology for future space missions. Flip-chip interconnect technology is an advanced electrical interconnection approach where the silicon die or chip is electrically connected, face down, to the substrate by reflowing solder bumps on area-array metallized terminals on the die to matching footprints of solder-wettable pads on the chosen substrate. This advanced flip-chip interconnect technology will significantly improve the performance of high-speed systems, productivity enhancement over manual wire bonding, self-alignment during die joining, low lead inductances, and reduced need for attachment of precious metals. The use of commercially developed no-flow fluxing underfills provides a means of reducing the processing steps employed in the traditional capillary flow methods to enhance SMT compatibility. Reliability of flip chips may be significantly increased by matching/tailoring the CTEs of the substrate material and the silicon die or chip, and also the underfill materials. Advanced packaging interconnects technology such as flip-chip interconnect test boards have been subjected to various extreme temperature ranges that cover military specifications and extreme Mars and asteroid environments. The eventual goal of each process step and the entire process is to produce components with 100 percent interconnect and satisfy the reliability requirements. Underfill materials, in general, may possibly meet demanding end use requirements such as low warpage, low stress, fine pitch, high reliability, and high adhesion.
Leveraging its private resources with several Small Business Innovation Research (SBIR) contracts with both NASA and the U.S. Department of Defense, WebCore Technologies LLC, of Miamisburg, Ohio, developed a fiber-reinforced foam sandwich panel it calls TYCOR that can be used for a wide variety of industrial and consumer applications. Testing at Glenn Research Center?s Ballistic Impact Facility demonstrated that the technology was able to exhibit excellent damage localization and stiffness during impact. The patented and trademarked material has found use in many demanding applications, including marine, ground transportation, mobile shelters, bridges, and most notably, wind turbines.
One of key NASA goals is to develop and integrate noise reduction technology to enable unrestricted air transportation service to all communities. One of the technical priorities of this activity has been to account for and reduce noise via propulsion/airframe interactions, identifying advanced concepts to be integrated with the airframe to mitigate these noise-producing mechanisms. An adaptive geometry chevron using embedded smart structures technology offers the possibility of maximizing engine performance while retaining and possibly enhancing the favorable noise characteristics of current designs. New high-temperature shape memory alloy (HTSMA) materials technology enables the devices to operate in both low-temperature (fan) and high-temperature (core) exhaust flows. Chevron-equipped engines have demonstrated reduced noise in testing and operational use. It is desirable to have the noise benefits of chevrons in takeoff/landing conditions, but have them deployed into a minimum drag position for cruise flight. The central feature of the innovation was building on rapidly maturing HTSMA technology to implement a next-generation aircraft noise mitigation system centered on adaptive chevron flow control surfaces. In general, SMA-actuated devices have the potential to enhance the demonstrated noise reduction effectiveness of chevron systems while eliminating the associated performance penalty. The use of structurally integrated smart devices will minimize the mechanical and subsystem complexity of this implementation. The central innovations of the effort entail the modification of prior chevron designs to include a small cut that relaxes structural stiffness without compromising the desired flow characteristics over the surface; the reorientation of SMA actuation devices to apply forces to deflect the chevron tip, exploiting this relaxed stiffness; and the use of high-temperature SMA (HTSMA) materials to enable operation in the demanding core chevron environment. The overall conclusion of these design studies was that the cut chevron concept is a critical enabling step in bringing the variable geometry core chevron within reach. The presence of the cut may be aerodynamically undesirable in some respects, but it is present only when the chevron is not immersed in the core jet exhaust. When deployed, the gap closes as the chevron tip enters the high-speed, high-temperature core stream. Aeroacoustic testing and flow visualization support the contention that this cut is inconsequential to chevron performance.
Efforts are under way to develop a nanofluidic size-exclusion chromatograph (SEC), which would be a compact, robust, lightweight instrument for separating molecules of interest according to their sizes and measuring their relative abundances in small samples. About as large as a deck of playing cards, the nanofluidic SEC would serve, in effect, as a laboratory on a chip that would perform the functions of a much larger, conventional, bench-top SEC and ancillary equipment, while consuming much less power and much smaller quantities of reagent and sample materials. Its compactness and low power demand would render it attractive for field applications in which, typically, it would be used to identify and quantitate a broad range of polar and nonpolar organic compounds in soil, ice, and water samples. Size-exclusion chromatography is a special case of high-performance liquid chromatography. In a conventional SEC, a sample plug is driven by pressure along a column packed with silica or polymer beads that contain uniform nanopores. The interstices between, and the pores in, the beads collectively constitute a size-exclusion network. Molecules follow different paths through the size-exclusion network, such that characteristic elution times can be related to sizes of molecules: basically, smaller molecules reach the downstream end of the column after the larger ones do because the smaller ones enter minor pores and stay there for a while, whereas the larger ones do not enter the pores. The volume accessible to molecules gradually diminishes as their size increases. All molecules bigger than a pore size elute together. For most substances, the elution times and sizes of molecules can be correlated directly with molecular weights. Hence, by measuring the flux of molecules arriving at the downstream end as a function of time, one can obtain a liquid mass spectrum for the molecules present in a sample over a broad range of molecular weights.
Long-wavelength infrared (LWIR) focal plane arrays (FPAs) needed for Earth Science imaging, spectral imaging, and sounding applications have always been among the most challenging in infrared photodetector technology due to the rigorous material growth, device design and fabrication demands. Future small satellite missions will present even more challenges for LWIR FPAs, as operating temperature must be increased so that cooler (and radiator) volume, mass, and power can be reduced.
Concrete production in the U.S. accounted for nearly 393 million cubic yards in 2023, with $38.8 billion in revenue. While cement, the key ingredient in concrete, is only 10%-15% of concrete's mixture by mass, 8% of total global emissions come from the production of cement. A significant challenge lies in the fact that roughly 51% of concrete emissions stem from the material calcination process of cement production. Stakeholders ranging from cement producers to government agencies are beginning to take measures to significantly reduce concrete emissions by 2050 and are seeking novel technologies from the startup community. Strategies to lower carbon emissions include reducing quantities of cement in concrete formulas; optimizing digital and automated production; lower temperature processing; carbon capture, utilization, and durable storage; and other cost-saving approaches to energy and material efficiencies. New materials based on carbon mineralization and novel cement chemistries hold the potential to reach net-zero or even carbon-negative concrete production; however, there is presently no readily available substitute that can replicate concrete's unique properties and versatility at the volume demanded by construction worldwide. The nature of concrete's raw materials, diverse applications, and scale of demand means that complete decarbonization will rely on a combination of innovative production methods and novel cement chemistries. Low-carbon solutions will need to compete economically with traditional concrete to become viable in a high-volume commodity market, although consumer demand and regulation will play important roles. Despite these challenges, this analysis reveals that venture capital (VC) investments in low-carbon concrete reflect a growing awareness of the decarbonized cement market opportunity. Between 2022 and 2023 emerging low-carbon technologies garnered more than $700 million in VC investments, representing a growing share of investment in the built environment. An investment gap appears after Series A for technology solutions, demonstrating the sector's potential, as well as the need for additional performance assurance and technology incubation.
The integration of heat pumps with thermal energy storage (HP-TES) systems is gaining attention as a viable solution for managing peak building demand driven by immense cooling and heating loads. With growing reliance on renewable energy sources, thermal energy storage offers an excellent opportunity to mitigate mismatches in thermal load between energy supply and demand. The use of phase-change material (PCM) TES is especially promising, as PCMs offer significant latent energy storage capacity with smaller temperature glides in smaller volumes compared to other TES technologies. However, challenges arise because current HP-TES architectures can load-shift only cooling or heating, not both, requiring two systems and thus doubling cost, weight, and footprint. Furthermore, current research efforts lack specific tools and techniques to advance integrated systems from concept design to end-user application, focusing on only discharge performance. To address these challenges, this research proposes a dual-mode (heating and cooling) integrated HP-TES system that uses room-temperature PCM-TES as a high-temperature heat source in heating mode and a low-temperature heat sink in cooling mode, thereby reducing temperature lifts and compressor power. Design criteria for PCM-TES heat exchangers were developed, balancing thermal-hydraulic performance with practical constraints such as available building space and weight requirements along with PCM selection considerations such as shipping conditions, moisture exposure, and number of available cycles. A detailed transient model for HP-TES systems was developed to enable rapid annual performance assessments in any US climate zone.
Controlling interface clearances is the most cost effective method of enhancing turbomachinery performance. Seals control turbomachinery leakages, coolant flows and contribute to overall system rotordynamic stability. In many instances, sealing interfaces and coatings are sacrificial, like lubricants, giving up their integrity for the benefit of the component. They are subjected to abrasion, erosion, oxidation, incursive rubs, foreign object damage (FOD) and deposits as well as extremes in thermal, mechanical, aerodynamic and impact loadings. Tribological pairing of materials control how well and how long these interfaces will be effective in controlling flow. A variety of seal types and materials are required to satisfy turbomachinery sealing demands. These seals must be properly designed to maintain the interface clearances. In some cases, this will mean machining adjacent surfaces, yet in many other applications, coatings are employed for optimum performance. Many seals are coating composites fabricated on superstructures or substrates that are coated with sacrificial materials which can be refurbished either in situ or by removal, stripping, recoating and replacing until substrate life is exceeded. For blade and knife tip sealing an important class of materials known as abradables permit blade or knife rubbing without significant damage or wear to the rotating element while maintaining an effective sealing interface. Most such tip interfaces are passive, yet some, as for the high-pressure turbine (HPT) case or shroud, are actively controlled. This work presents an overview of turbomachinery sealing. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.
Nuclear thermal propulsion (NTP) is an in-space propulsion method currently being developed at the NASA Marshall Space Flight Center (MSFC). NTP systems are a high specific impulse (750–1,100 s), high thrust (15,000–250,000 lbf ) method of propulsion which have the potential to allow for faster transit times when optimizing for high ΔV. In the nuclear rocket engine, the heat from the nuclear fission reaction is transferred to a low molecular mass propellant (such as hydrogen). Hot propellant is expanded through a nozzle to generate thrust. Development of ceramic metal (cermet) fuel systems for NTP applications is currently ongoing at MSFC. In cermet fuel systems, ceramic fissile fuel particles such as uranium nitride or uranium dioxide are dispersed within a net-shaped, high-density structural matrix. The composite material is cladded by a protective metal structure to make up an NTP fuel element. Cladding materials must be able to withstand the demanding operating conditions required of the engine as well as retain a hermetic seal to allow for retention of fuel element structural integrity, prevent hydrogen attack or migration of the ceramic fuel, and limit release of fission products during operation. For NTP applications, tungsten is a prime material for both the metal matrix and cladding in cermet fuel systems because of its high melting point, high temperature strength, and compatibility with hot hydrogen. If a weld in tungsten with the capability of holding a hermetic seal is achievable, tungsten becomes a strong candidate for NTP applications. This Technical Memorandum focuses on determining the weldability of pure tungsten using electron beam welding (EBW). Tungsten appears well suited for NTP applications, but it has a high ductile to brittle transition temperature (DBTT) dependent upon chemical composition, structure/stress distribution, and mechanical conditions. Therefore, it is highly subject to brittle fracture. Because of its high susceptibility to brittle fracture, it is very difficult to weld. EBW was chosen for joining pure tungsten because of its low heat input compared to gas tungsten arc welding. Reduced heat input can be directly correlated with an increase in ductility of a tungsten weld. EBW is a high energy density welding process in which a stream of electrons penetrates a weld joint in a deep, narrow spike in contrast to a broad gas tungsten arc weld pool. The investigation initially focused on EBW of tungsten plates of both 0.01 in and 0.03 in thickness to determine if EBW could weld pure tungsten without the presence of visual defects—particularly cracking—in the welds. Variation in the weld procedure and post-weld heat treatment (PWHT) was used to improve the surface appearance of flat EBWs on a pure tungsten sheet. The investigation moved on to weld 0.05-in-thick hexagonal tungsten cans with a weld joint thickness of 0.025 in. The goal for welding the pure tungsten hex cans was to avoid any visual surface defects and generate a weld capable of a hermetic seal. This proved difficult. Cold welds commonly exhibited porosity that leaked air. Hot welds exhibited cracks, typically observed immediately after welding. Later welds were preheated to increase ductility and decrease the likelihood of through-thickness cracking. PWHT was used to arrest microcrack growth both in the flat weld samples and hexagonal weld samples.
The demand for electric vehicles (EVs) in the United States is projected to rise significantly, with sales expected to reach approximately 4.1 million units by 2030. However, the U.S. remains heavily reliant on imports for the batteries and critical raw materials—such as lithium, cobalt, and nickel—that power these vehicles. As of 2024, around 70% of these imports originate from China. This dependency has become even more precarious following China’s imposition of export restrictions in April 2025, a retaliatory move against U.S. tariffs. These developments highlight the strategic vulnerabilities posed by China’s dominant position in the critical materials market. Compounding the issue, decades of intensive extraction have severely depleted global reserves of critical materials, widening the gap between supply and growing demand. This situation underscores the urgent need for the U.S. and other nations to diversify their sources of critical materials and enhance domestic capabilities to secure these resources—an essential step toward ensuring long-term energy security. At the end of their lifecycle—whether due to the battery’s degradation or the retirement of the vehicle—EV batteries are often improperly disposed of or sent to landfills. However, many of these batteries still retain usable capacity and can follow one of three alternative pathways: (a) Re-used: deployed in another vehicle with a shorter driving range, (b) Re-purposed: utilized act as a backup storage/power for data centers, solar panels, and e-scotters or (c) Recycled: broken down to recover the critical materials. To that end, the proposed tool (REBORN) is designed to optimize the reverse logistics network for battery repurposing and recycling. Its goal is to minimize associated costs while identifying optimal locations for battery collection and processing. Ultimately, REBORN ensures that each battery is used to its fullest potential.
Over the past forty years, microgravity has inspired and enabled applications in a wide range of sectors including medicine, materials, computers, communications, and national defense. Trends show that demand for high-tech solutions is increasing in these sectors, solutions that require higher resolution, greater precision, novel materials, innovative processes, and more sophisticated tools. These are areas where microgravity can offer unique capabilities for innovation. The Emerging Space Office (ESO) has engaged in multiple studies over the past year that have found that microgravity RD is one of the most promising technology areas for contributing to economic growth and to NASAs mission. The focus of these studies was on terrestrial markets rather than NASA applications, applied research rather than basic research, and commercial rather than academic investigators. There have been more success stories than are generally appreciated and there are significant areas of promising future potential. Many of the problems that have limited commercial microgravity development in the past are being solved. Microgravity research and development (RD) requires iteration and learning, as rapidly as possible. New technologies enable high throughput and rapid data collection in increasingly small payloads. The International Space Station is in orbit and provides a laboratory that is available 247 at least until 2024. Frequent flights by commercial space providers to and from the ISS now enable the fast learning cycles needed by high-tech industries. Launch costs are decreasing and the ability to return payloads to Earth is increasing. New commercial space laboratories, such as those being developed by SpaceX and Bigelow Aerospace, are in the final stages of development and testing. This ecosystem for microgravity RD has never been available before. These are game-changer conditions for attracting high-tech industries to space for terrestrial, as well as NASA, applications. However, few know that these capabilities are available or how to use them. In aggregate, the potential value for new applications from microgravity RD over the next ten years could add billions of dollars per year in terrestrial applications to the future economy, create new jobs, and generate a wide range of public benefits in medical advances, while broadening the customer base for the emerging space industry.
Los Alamos National Laboratory (LANL) is a multidisciplinary national laboratory that conducts research and development in national security, engineering, materials science, computational modeling, and advanced manufacturing. The laboratory develops innovative technologies to address complex scientific and engineering challenges. This project focuses on the development and evaluation of high-performance absorbing structures through computational design, simulation, and engineering analysis. Absorbing structures are used in applications where damage mitigation, structural protection, and material efficiency are critical performance requirements. The increasing demand for lightweight, high-strength, and highly efficient structural systems has created a need for improved design methodologies capable of maximizing absorption while minimizing weight and material usage. The project utilizes advanced engineering software, including 3D CAD software and FEA, to generate and optimize structural concepts. Computational simulations are performed to evaluate structural behavior under loading conditions, while mathematical analyses are conducted using Python-based tools as well as established analytical equations from material and structural mechanics. The project benefits LANL by supporting the development of advanced design methodologies and improving the understanding of material and structural performance. During the internship term, a significant portion of the design development, simulation, and data analysis activities will be completed. Success of the project depends on collaboration among engineering mentors and technical staff members. Work will be conducted at Los Alamos National Laboratory using laboratory computing resources and engineering software.
Flight proven entry system and TPS technologies are critical for the successful execution of in-situ science missions at Venus. Emerging new technologies point to new possibilities and offer innovative approaches to delivering small satellites for orbital science. Venus entry can be very demanding and there are only a few flight proven TPS, some developed by Industry and others by NASA, capable of meeting the mission needs. NASA developed TPS has predominately been transferred to Industry and it is assumed industry will maintain the fabrication capability. However, lack of mission needs may result in obsolence of TSP fabrication capability if there is no money and no motivation. Even within NASA, its' expertise could be diverted to higher priority objectives and thereby the readiness for particular material systems can be impacted or lost. Atrophy of capabilities can come about in other ways as well such as changes to raw materials. Even small manufacturing process changes can demand requalification and TRL may be degraded. Carbon-Phenolic is a text book example. After a long period of absence of US Venus missions, VEXG and the Science community is making the case for future missions. It is insufficient to assume the TSP technologies will be there in 5 or 10 years without active and continual planning and assessment. After Galileo, Carbon-Phenolic materials and fabrication skills were allowed to atrophy. Then when missions needed it, in early 2000, it was no longer possible to make the heritage Carbon-Phenolic. What do we need to do? The first step is to advocate for the establishment of TPS readiness assess-ment. The assessment will involve understanding threats and opportunities, and the development of risk mitigation strategies. VEXAG needs to advocate for such an active monitoring of the needed capabilities, assessment of emerging risks and development of risk mitigation strategies with implementation plans. Such an approach reduces the threat of material obsolence and helps maintain the availability of entry system and TPS technology capabilities, both old and new. Venus probes, landers, balloons and other variable altitude missions, and skimmer missions such as "Cu-pid's Arrow" as well as aerocapture missions to deliver small spacecraft require qualified entry systems and ablative TPS. VEXAG advocated for HEEET in 2013/2014 and the community is well versed with the need to sustain it. But, other TPS that need to be sustained may not be apparent to VEXAG community. The following figure summarizes the ablative TPS capabilities vs Venus mission needs for both primary heatshield and backshell.
With the ever-increasing demand for high beam power, the currently used beam-intercepting devices (BIDs) such as targets, and beam windows may not be able to handle the high power required for future accelerator complexes or the lifetime may be reduced drastically. As beam power increases, the damage incurred by BIDs, including thermal shock, fatigue, and irradiation damage, also rises. Therefore, it is imperative to design materials that can withstand high beam power for longer lifetimes. High entropy alloys (HEAs) have emerged as potential alternative materials for designing next-generation BIDs. In this study, we primarily focus on materials for developing beam windows for next-generation accelerator complexes. We propose an integrated approach that combines various computational techniques to study and design new materials. Specifically, we use CALPHAD, density functional theory (DFT), and molecular dynamics (MD) to comprehensively investigate the defect properties of suitable HEAs, offering potential alternatives for future beam windows. We begin by scanning the extensive phase space provided by Cr-Mn-V-Ti-Al-Co HEAs, selecting 8 compositions after evaluating approximately 120,000 unique compositions using CALPHAD. We, then employ DFT-informed machine learning techniques to develop force-field parameters. Finally, MD simulations using these developed force-field parameters will be used to study the effects of radiation damage on the defect and mechanical properties of the selected alloys. This research explains the use of the CALPHAD approach and shows how critical modeling (DFT and MD) is in developing novel material such as HEAs. It also highlights the promising role of machine learning in this field. The results from this study will greatly improve the novel materials development to be used in next-generation accelerator components, leading to higher beam power and longer operational times of BIDs.