Search NASA⌕ Search

SEARCH · Search NASA

Results for “material elastic constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Flow Strength Measurements of Wrought and AM SS304L via Pressure Shear Plate Impact Experiments

Pressure-shear plate impact experiments were performed to quantify flow strength of wrought, as-built additively manufactured (AM), and heat-treated and recrystallized AM 304 L stainless steel (SS304L) under combined loading. Impact velocities spanned between 0.03 and 0.24 mm/μs, resulting in corresponding pressures of 0.62–5.93 GPa. Flow strength measurements are comparable for the sample variants across the studied loading conditions; however, shear wave structures significantly differ between sample type. Microstructurally aware simulations indicate local strain differences attributed to anisotropic elastic constants of large grains (~1 mm) in the as-built and heat-treated AM may impede the ability to uniformly transmit a shear wave.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Thermal loading effects on chalk hydromechanical behavior for nuclear waste disposal

Safe disposal of heat-generating nuclear waste depends on host rock stability under thermal, hydrological, and mechanical stresses. This study investigates the effect of thermal loading on mechanical behavior of the shallowly buried Ghareb formation chalk through triaxial and hydrostatic constant strain rate and creep tests at temperatures up to 100 ˚C and effective pressures up to 20.7 MPa. Experimental results show that thermal loading reduces the elastic moduli of chalk by 50–75%, and a transition occurs above 60 ˚C where creep rates increase rapidly. Water saturation nearly doubles the thermally induced strain compared to dry conditions and strongly decreases material rigidity. Thermal loading also leads to significant pore pressure increases under undrained conditions and leads to reductions in the apparent permeability during drained conditions. Laboratory experimental data were used to parameterize and develop a preliminary constitutive model for predicting future deformation during repository operations in the Ghareb. The strongly coupled effects – mechanical weakening, fluid pressure fluctuations, and permeability modification – demonstrate that elevated repository temperatures will have a pronounced effect on the near field Ghareb behavior during waste disposal operations. The findings indicate that the coupled interactions must be considered in predictive models and repository design to ensure long-term nuclear waste isolation and safety.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2000

A Hot-Electron Far-Infrared Direct Detector

A new approach is proposed to improve the sensitivity of direct-detection bolometers at millimeter, submillimeter and far-infrared wavelengths. The idea is to adjust a speed of the thermal relaxation of hot-electrons in a nanometer size normal metal or super-conductive transition edge bolometer by controlling the elastic electron mean free path. If the bolometer contacts are made of a superconductor with high critical temperature (Nb, Pb etc.) then the thermal diffusion into the contacts is absent because of the Andreev's reflection and the electron-phonon relaxation is the only mechanism for heat removal. The relaxation rate should behave as T(sup 4)l at subkelvin temperatures (l is the electron elastic mean free path) and can be reduced by factor of 10-100 by decreasing l. Then an antenna- or waveguide-coupled bolometer with a time constant about 10(exp -3) to 10(exp -5) s at T approximately equals 0.1-0.3 K will exhibit photon-noise limited performance in millimeter and submillimeter range. The choice of the bolometer material is a tradeoff between a low electron heat capacity and fabrication. A state-of-the-art bolometer currently offers NEP = 10(exp -17) W(Square root of (Hz)) at 100 mK along with a approximately equals 2 msec time constant. The bolometer we propose will have a figure-of-merit, NEP(square root (r)), which is 10(exp 3) times smaller. This will allow for a tremendous increase in speed which will have a significant impact for observational mapping applications. Alternatively, the bolometer could operate at higher temperature with still superior sensitivity. This device can significantly increase a science return and reduce the cost for future observational missions. This research was performed by the Center for Space Microelectronics Technology, Jet Propulsion Laboratory, California Institute of Technology, and was sponsored by NASA, Office of Space Science.

Karasik, B. S.↗
DOE OSTI2022

Carburization Kinetics of Zircalloy-4 and Its Implication for Small Modular Reactor Performance

Carburization of cladding materials has long been a concern for the nuclear industry and has led to the restricted use of high-thermal conductivity fuels such as uranium carbides. With the rise of small modular reactors (SMRs) that frequently implement a graphite core-block, carburization of reactor components is once more in the foreground as a potential failure mechanism. To ensure commercial viability for SMRs, neutron-friendly cladding materials such as Zr-based alloys are required. In this work, the carburization kinetics of Zircaloy-4 (Zry-4), for the temperature range 1073–1673 K (covering typical operating temperatures and off-normal scenarios) are established. The following Arrhenius relationship for the parabolic constant describing ZrC growth is derived: Kp (in μm2/s) = 609.35 exp(−1.505 × 105/RT)). Overall, the ZrC growth is sluggish below 1473 K which is within the operational temperature range of SMRs. In all cases the ZrC that forms from solid state reaction is hypo-stoichiometric, as confirmed through XRD. The hardness and elastic modulus of carburized Zry-4 are also examined and it is shown that despite the formation of a ZrC layer, C ingress in the Zry-4 bulk does not impact the mechanical response after carburization at 1073 K and 1473 K for 96 h.

36 MATERIALS SCIENCE↗
NASA NTRS1976

A finite-element analysis of fatigue crack closure

The paper is concerned with the application of a two-dimensional, nonlinear, finite-element analysis using an incremental theory of plasticity to predict crack-closure and crack-opening stresses during the crack-growth process under cyclic loading. A two-dimensional finite-element computer program is developed, which accounts for both elastic-plastic material behavior and changing boundary conditions associated with crack extension and intermittent contact of the crack surfaces under cyclic loading. An efficient technique to account for changing boundary conditions under cyclic loading is also incorporated into the nonlinear analysis program. This program is used to study crack extension and crack closure behavior in a center-cracked panel under constant-amplitude and two-level block loading. The calculated crack-opening stresses are found to be quantitatively consistent with experimental measurements.

Newman, J. C., Jr.↗
DOE OSTI2023

Multi-reward reinforcement learning based development of inter-atomic potential models for silica

Abstract Silica is an abundant and technologically attractive material. Due to the structural complexities of silica polymorphs coupled with subtle differences in Si–O bonding characteristics, the development of accurate models to predict the structure, energetics and properties of silica polymorphs remain challenging. Current models for silica range from computationally efficient Buckingham formalisms (BKS, CHIK, Soules) to reactive (ReaxFF) and more recent machine-learned potentials that are flexible but computationally costly. Here, we introduce an improved formalism and parameterization of BKS model via a multireward reinforcement learning (RL) using an experimental training dataset. Our model concurrently captures the structure, energetics, density, equation of state, and elastic constants of quartz (equilibrium) as well as 20 other metastable silica polymorphs. We also assess its ability in capturing amorphous properties and highlight the limitations of the BKS-type functional forms in simultaneously capturing crystal and amorphous properties. We demonstrate ways to improve model flexibility and introduce a flexible formalism, machine-learned ML-BKS, that outperforms existing empirical models and is on-par with the recently developed 50 to 100 times more expensive Gaussian approximation potential (GAP) in capturing the experimental structure and properties of silica polymorphs and amorphous silica.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A finite viscoelastic constitutive model for low to high strain rate response of elastomers with application of strain rate-induced glass transition

Amorphous elastomers exhibit significant rate-stiffening and unique viscous flow characteristics across a wide range of strain rates, often undergoing glass transition above a strain rate threshold. We have developed a thermodynamically-consistent and micromechanically-inspired constitutive model for soft elastomeric materials to capture the rate-dependent stress-strain behavior and hysteresis when subjected to low to high strain rates. Here, our proposed constitutive model encapsulates the viscous flow of materials through molecular motion at low strain rates and local rearrangement and alignment of the molecules trying to overcome the intermolecular resistance at high strain rates, essentially covering the glass transition. We applied our constitutive model to uniaxial compression experiments performed at low and high strain rates for polyborosiloxane (PBS) to identify the material parameters, and subsequently, performed numerical simulations of single and multi-cycle compression, stress relaxation, and small amplitude oscillatory tension-compression. Our analyses indicate that the model predicts higher total energy dissipation with increasing strain rate; however, dissipation associated with molecular relaxation decreases (forming a cusp) because, beyond a crossover strain rate, intermolecular rearrangement and alignment become dominant, which is consistent with the onset of the glass transition. For cyclic loading-unloading, we observed that dissipation over a cycle remains constant at low strain rates but decreases non-monotonically at high strain rates before becoming constant, with the peak stress over the cycle becoming higher, which can be interpreted as more loading being carried elastically by the polymer network as the intermolecular rearrangement process occurs. Additionally, our model was able to predict the qualitative nature of the storage modulus and loss modulus in the limit of small strain over a wide range of frequency sweeps.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Analytical and experimental investigations of human spine flexure.

The authors report on experiments to measure the resistance of fresh human spines to flexion in the upper lumbar and lower thoracic regions and evaluate results by using a combination of strength of materials theory and effects of shear and comparing with data reported by other authors. The test results indicate that the thoraco-lumbar spine behaves approximately as a linear elastic beam, without relaxation effects. The authors formulate a simple continuum dynamic model of the spine simulating aircraft ejection and solve the resulting boundary value problem to illustrate the importance of the flexural mode. A constant cross-section, the selected model is a sinusoidally curved elastic beam with an end mass subjected to a Heaviside axial acceleration at the other end. The paper presents transient response results for the spinal model axial and bending displacements and axial force.-

Moffatt, C. A.↗
NASA NTRS1992

Effects of constraint on crack growth under aircraft spectrum loading

The objective is to study the effects of constraint on fatigue crack growth under aircraft spectrum loading. A plasticity-induced crack-closure model that accounts for constraint variations during the transition from flat-to-slant crack growth was used to correlate crack-growth rate data under constant-amplitude loading and to calculate crack growth under simulated aircraft spectrum loading. The model was applied to several thin-sheet aluminum alloy materials. Under laboratory air conditions, the transition was shown to be related to the size of the cyclic plastic zone based on the effective stress-intensity factor range for several sheet materials and thicknesses. Results from three-dimensional, elastic-plastic, finite-element analyses of a flat, straight-through crack in a thin-sheet aluminum alloy specimen showed a constraint loss similar to that assumed in the model. Using test data and the closure model, the location of the constraint-loss regime in terms of growth rate and the value of the constraint factor at these rates were determined by trial and error. The model was then used to calculate crack growth under the TWIST spectrum. The calculated results agreed reasonably well with test data. In general, the model predicted shorter crack-growth lives than tests under the TWIST spectrum by about 40 percent. For the TWIST spectrum clipped at Level 3, the calculated lives were within about 20 percent. The results demonstrated that constraint variations, especially for thin-sheet alloys, should be accounted for to predict crack growth under typical aircraft spectra.

Newman, J. C., Jr.↗
NASA NTRS1973

Mechanical property determination of high conductivity metals and alloys

Pertinent mechanical properties of three high conductivity metals and alloys; namely, vacuum hot pressed grade S-200E beryllium, OFHC copper and beryllium-copper alloy no. 10 were determined. These materials were selected based on their possible use in rocket thrust chamber and nozzle hardware. They were procured in a form and condition similar to that which might be ordered for actual hardware fabrication. The mechanical properties measured include (1) tension and compression stress strain curves at constant strain rate (2) tensile and compressive creep, (3) tensile and compressive stress-relaxation behavior and (4) elastic properties. Tests were conducted over the temperature range of from 75 F to 1600 F. The resulting data is presented in both graphical and tabular form.

Harrod, D. L.↗
NASA NTRS1946

Quantitative treatment of the creep of metals by dislocation and rate-process theories

An equation for the steady-state rate of creep has been derived by applying the theory of dislocations to the creep of pure metals. The form of this equation is in agreement with empirical equations describing creep rates. The theory was also used to predict the dependence of steady-state rate of creep on physical constants of the material and good agreement was obtained with data in the literature for pure annealed metals. The rate of creep was found to decrease with increasing modulus of rigidity. This relation suggest that one of the requirements for a heat-resisting alloy is that its matrix be a metal that has a high modulus of rigidity and therefore a high modulus of elasticity.

Nowick, A S↗
NASA NTRS1972

Automated testing data reduction computer program

The capability of a computer program which can be part of a larger computer program for a fully automated multiaxial testing facility is described. The program was designed to process test data from tubular or flat specimens made from isotropic or anistropic materials, including high modulus fiber composites. Data from a large number of strain gages and combinations of applied loads can be used. Options are provided for single element, 90-degree, rectangular or Delta rosettes, or any combinations of these types of strain gages. Options are provided for strain gage transverse sensitivities. The program outputs include: structural axes strains and stresses, initial and strain-dependent elastic constants, shift of principal strain direction with load, and local curvatures from back-to-back strain gages, and either Calcomp or microfilm plots. The computer program is described with respect to its flow chart, input/output, embedding or linking with other programs.

Chamis, C. C.↗
NASA NTRS1972

Automated testing data reduction computer program.

The capability of a computer program which can be part of a larger computer program for a fully automated multiaxial testing facility is described. This computer program is designed to process test data from tubular or flat specimens made from isotropic or anisotropic materials including high modulus fiber composites. The program can receive data from a large number of strain gages and combinations of applied loads. Options are provided for single element, 90-degree, rectangular or Delta rosettes, or any combinations of these types of strain gages. Options are provided for strain gage transverse sensitivities. The program outputs include: structural axes strains and stresses, initial and strain dependent elastic constants, shift of principal strain direction with load, and local curvatures from back-to-back strain gages, and either calcomp or microfilm plots. The computer program is described with respect to its flow chart, input/output, embedment or linking with other programs and its possible utility in a fully automated testing system.

Chamis, C. C.↗
NASA NTRS1976

Rapid interface flaw extension with friction

An idealized two-dimensional example of rapid interface flow extension is described. Initially undisturbed dissimilar isotropic, homogeneous, linearly elastic half-spaces are perfectly bonded along the interface y=0. Quantities associated with the half-space or = to 0 are denoted by the prime superscript or the subscripts 3 or 4 while those in y or = to 0 carry the subscripts 1 or 2. At time t=0 adjacent material points at x=0, y= + or - 0 are forced apart horizontally with a constant relative velocity delta v. This results in a zone of bond failure which extends symmetrically along the interface at a constant rate c. The newly created flaw surfaces are in sliding contact resisted by Coulomb friction. The friction coefficient is gamma.

Brock, L. M.↗
DOE OSTI2024

First-principles investigation of elastic, vibrational, and thermodynamic properties of kagome metals CsM 3 Te 5 (M = Ti, Zr, Hf)

Kagome metals are a unique class of quantum materials characterized by their distinct atomic lattice arrangement, featuring interlocking triangles and expansive hexagonal voids. These lattice structures impart exotic properties, including superconductivity, interaction-driven topological many-body phenomena, and magnetism, among others. The kagome metal CsM 3 ⁢Te 5 (where M = Ti, Zr, or Hf) exhibits both superconductivity and nontrivial topological electronic properties, offering a promising platform for exploring topological superconductivity. This study employs first-principles density functional theory calculations to systematically analyze the elastic, mechanical, vibrational, thermodynamic, and electronic properties of CsM 3 ⁢Te 5 (M = Ti, Zr, Hf). Our calculations reveal that the studied compounds—CsTi 3 ⁢Te 5 , CsZr 3 ⁢Te 5 , and CsHf 3 ⁢Te 5 —are ductile metals with elastic properties akin to the hexagonal Bi and Sb, with average elastic constants, including a bulk modulus of 27 GPa, a shear modulus of 11 GPa, and Young's modulus of 29 GPa. We observe peculiar dispersionless, flat, phonon branches in the vibrational spectra of these metals. Additionally, we thoroughly analyze the symmetries of the zone-center phonon eigenvectors and predict vibrational fingerprints of the Raman- and infrared-active phonon modes. The analysis of thermodynamic properties reveals the Einstein temperature for CsTi 3 ⁢Te 5 , CsZr 3 ⁢Te 5 , and CsHf 3 ⁢Te 5 to be 66, 54, and 53 K, respectively. Our orbital-decomposed electronic structure calculations reveal significant in-plane steric interactions and multiple Dirac band crossings near the Fermi level. We further investigate the role of spin-orbit coupling effect on the studied properties. Furthermore, this theoretical investigation sheds light on the intriguing quantum behavior of kagome metals.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of internal swelling on residual elasticity of a quasi-brittle material through a composite sphere model

This work describes the development of a micromechanical-based constitutive model accounting for the effect of internal expansion on the residual elasticity of a Hashin composite material. This material is made of spherical inclusions that are subjected to gradual swelling within a quasi-brittle matrix. The main focus of this work is to describe and analyze the material mechanical response, with an additional focus on the internal swelling’s effect on the stress–strain response and residual elasticity. Microstructural features and parameters of major importance for the mechanical responses were identified. The innovative characteristics of the proposed approach are summarized as follows: (1) a full determination of the physics of a complete-damage problem throughout the whole process of inclusion swelling with upscaling techniques, which transfers the microcrack-related properties from the lower scale to upper scale; and (2) an evolution of the mechanical fields and the corresponding residual elasticity for various inclusion swelling levels. Concerning the matrix–inclusion composite, it was hypothesized that only the matrix was susceptible to cracking, with varied degrees of damage, whereas the inclusions behave elastically and the elastic modulus of the expanding inclusions remains constant. It is to emphasize that the gradual swelling of inclusions is modeled by an increasing strain in the current micromechanical-based constitutive model, and the microcracks are represented by a set of randomly oriented penny-shaped microcracks with identical radii (namely, closed cracks). The main contribution of the current research is to establish the exact mathematical solutions for the mechanical fields (stress, strain) caused by the swelling of the inclusions (mechanical loading) and derive the effective residual elasticity of a composite (structural response) subject to internal expansion and quasi-brittle damage. Based on the assumption of closed cracks that could be extended to open cracks in the upcoming work, the results proposed by the present paper help to understand the non-linear mechanical behavior of quasi-brittle materials subject to microcracking and provide a theoretical framework to be used as academical benchmark for numerical simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Analysis of Element Size and Element Type on SS304L Material Model Performance

Finite element solutions are only valid if the information inputted into the models is a valid assumption. This is why it is important to determine if the model behaves as expected especially in the material response. Material models that consider deformation in the elastic and plastic regions are desirable. As a material deforms plastically, hardening will occur until the ultimate strength is reached due to the reduction of the cross sectional area in a uniaxial tensile test environment. A phenomenological approximation of this behavior which is known as power law hardening (plh) can be expressed as σ = σ y + K $ϵ^{n}_{p}$ where K and n are empirically determined constants, and σ y is the proportional limit of the material. The first objective of this study is to verify the behavior for a calibrated plh material model for selective deviatoric hexahedral elements when applied to a different material stock. The Sierra SM input for this calibrated model can be found in the appendix. The second objective of this study is to determine the differences in failure characteristics for considerably large shell elements versus that of fine hexahedral elements.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Stress concentrations for straight-shank and countersunk holes in plates subjected to tension, bending, and pin loading

A three dimensional stress concentration analysis was conducted on straight shank and countersunk (rivet) holes in a large plate subjected to various loading conditions. Three dimensional finite element analysis were performed with 20 node isoparametric elements. The plate material was assumed to be linear elastic and isotropic, with a Poisson ratio of 0.3. Stress concentration along the bore of the hole were computed for several ratios of hole radius to plate thickness (0.1 to 2.5) and ratios of countersink depth to plate thickness (0.25 to 1). The countersink angles were varied from 80 to 100 degrees in some typical cases, but the angle was held constant at 100 degrees for most cases. For straight shank holes, three types of loading were considered: remote tension, remote bending, and wedge loading in the hole. Results for remote tension and wedge loading were used to estimate stress concentration for simulated rivet in pin loading. For countersunk holes only remote tension and bending were considered. Based on the finite element results, stress concentration equations were developed. Whenever possible, the present results were compared with other numerical solutions and experimental results from the literature.

Shivakumar, K. N.↗