Search NASA⌕ Search

SEARCH · Search NASA

Results for “method of characteristics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Process characteristics and design methods for a 300 deg quad OP amp

The results of process characterization, circuit design, and reliability studies for the development of a quad OP amplifier intended for use up to 300 C are presented. A dielectrically isolated complementary vertical bipolar process was chosen to fabricate the amplifier in order to eliminate isolation leakage and the possibility of latch up. Characterization of NPN and PNP junctions showed them to be suitable for use up to 300 C. Interconnect reliability was predicted to be greater than four years mean time between failure. Parasitic MOS formation was eliminated by isolation of each device.

Beasom, J. D.↗

Numerical Solution of the Flow of a Perfect Gas Over A Circular Cylinder at Infinite Mach Number

A solution for the two-dimensional flow of an inviscid perfect gas over a circular cylinder at infinite Mach number is obtained by numerical methods of analysis. Nonisentropic conditions of curved shock waves and vorticity are included in the solution. The analysis is divided into two distinct regions, the subsonic region which is analyzed by the relaxation method of Southwell and the supersonic region which was treated by the method of characteristics. Both these methods of analysis are inapplicable on the sonic line which is therefore considered separately. The shapes of the sonic line and the shock wave are obtained by iteration techniques. The striking result of the solution is the strong curvature of the sonic line and of the other lines of constant Mach number. Because of this the influence of the supersonic flow on the sonic line is negligible. On comparison with Newtonian flow methods, it is found that the approximate methods show a larger variation of surface pressure than is given by the present solution.

Hamaker, Frank M.↗

Application of the OPTEX method for computing reflector parameters

We are investigating the OPTEX reflector model for obtaining few-group reflector parameters consistent with a reference power distribution in the core. In our study, the reference power distribution is obtained using a 142,872-region calculation defined over a 2D eighth-of-core pressurized water reactor and performed with the method of characteristics. The OPTEX method is based on generalized perturbation theory and uses an optimization algorithm known as parametric linear complementarity pivoting. The proposed model leads to few-group diffusion coefficients or P1-weighted macroscopic total cross sections that can be used to represent the reflector in full-core calculations. These few-group parameters can be spatially heterogeneous in order to correctly represent steel baffles present in modern pressurized water reactors. The optimal reflector parameters are compared to those obtained with a flux-volume weighting of the reflector cross sections recovered from the reference calculation. Important improvements in full-core power distribution are observed when the optimal parameters are used. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Comparison of Intercooler Characteristics

A method is presented of comparing the performance, weight, and general dimensional characteristics of inter-coolers. The performance and dimensional characteristics covered in the comparisons are cooling effectiveness, pressure drops and weight flows of the charge and cooling air, power losses, volume, frontal area, and width. A method of presenting intercooler data is described in which two types of charts are plotted; (1) A performance chart setting forth all the important characteristics of a given intercooler and (2) a replot of these characteristics for a number of intercoolers intended to assist in making a selection to satisfy a given set of installation conditions. The characteristics of commercial intercoolers obtained from manufacturers' data and of some computed designs are presented on this basis. A standard test procedure and instrumentation are suggested whereby comparable data may be obtained by different testing organizations.

Reuter, J. George↗

Applying image processing methods to study hydrodynamic characteristics in a rectangular spouted bed

This paper presents systematic image processing methods for investigating hydrodynamic characteristics in a rectangular spouted bed (30.2 mm × 101.6 mm). The objective is to provide a non-intrusive technique to determine the bed expansion ratio, the jet height and the fountain height due to their significant influence on the hydrodynamics of the entire bed. A high-speed video camera is used in the experiment with Geldart D particles as the bed material. After the image acquisition, image denoising, thresholding, logical and mask operations are applied correspondingly for the boundary discrimination, based on which an algorithm has been developed to determine the bed height successfully. With the discriminated boundary, morphological operations viz. erosion and dilation have been used to accurately determine the jet height and the fountain height. The feasibility of the technique is proven through profiles of bed expansion ratio, jet height and fountain height under three initial bed heights (0.0762 m, 0.102 m, and 0.127 m) for two different nozzle sizes (0.0096 m and 0.0127 m). Depending on the determination of the hydrodynamic characteristics, different flow regimes can be distinguished comprehensively through profiles of the bed expansion ratio and bed pressure drop in combination with the standard deviation of jet/fountain height. The proposed flow regime discrimination verifies the feasibility and effectiveness of the image processing methods in assessing the solids behavior in the spouted beds. Results about the variation of the jet height and the fountain height under current operating conditions as determined by the new technique are also discussed.

20 FOSSIL-FUELED POWER PLANTS↗

Bidirectional canopy reflectance and its relationship to vegetation characteristics

A method for determining the relationship between bidirectional canopy reflectance (CR) of a vegetated area and its characteristics (type and growth stage) is presented. In the method, the three-dimensional CR surface is expressed in terms of spherical harmonics which are weighted by appropriate coefficients, and the coefficients are analyzed by a cluster technique. The method is applied to four vegetation types (soybeans, corn, shinnery oak, and orchard grass) at various stages of growth.

Goel, Narendra S.↗

Method for calculating wing characteristics by lifting-line theory using nonlinear section lift data

A method is presented for calculating wing characteristics by lifting-line theory using nonlinear section lift data. Material from various sources is combined with some original work into the single complete method described. Multhopp's systems of multipliers are employed to obtain the induced angle of attack directly from the spanwise lift distribution. Equations are developed for obtaining these multipliers for any even number of spanwise stations, and values are tabulated for 10 stations along the semispan for asymmetrical, symmetrical, and antisymmetrical lift distributions. In order to minimize the computing time and to illustrate the procedures involved, simplified computing forms containing detailed examples are given for symmetrical lift distributions. Similar forms for asymmetrical and antisymmetrical lift distributions, although not shown, can be readily constructed in the same manner as those given. The adaptation of the method for use with linear section lift data is also illustrated. The adaptation has been found to require less computing time than most existing methods.

Sivells, James C↗

Numerical Modeling of Fluid Transient in Cryogenic Fluid Network of Rocket Propulsion System

Fluid transients, also known as water hammer, can have a significant impact on the design and operation of both spacecraft and launch vehicles propulsion systems. These transients often occur at system activation and shut down. For ground safety reasons, many spacecrafts are launched with the propellant lines dry. These lines are often evacuated by the time the spacecraft reaches orbit. When the propellant isolation valve opens during propulsion system activation, propellant rushes into lines creating a pressure surge. During propellant system shutdown, a pressure surge is created due to sudden closure of a valve. During both activation and shutdown, pressure surges must be predicted accurately to ensure structural integrity of the propulsion system fluid network. The method of characteristics is the most widely used method of calculating fluid transients in pipeline [ 1,2]. The method of characteristics, however, has limited applications in calculating flow distribution in complex flow circuits with phase change, heat transfer and rotational effects. A robust cryogenic propulsion system analyzer must have the capability to handle phase change, heat transfer, chemical reaction, rotational effects and fluid transients in conjunction with subsystem flow model for pumps, valves and various pipe fittings. In recent years, such a task has been undertaken at Marshall Space Flight Center with the development of the Generalized Fluid System Simulation Program (GFSSP), which is based on finite volume method in fluid network [3]. GFSSP has been extensively verified and validated by comparing its predictions with test data and other numerical methods for various applications such as internal flow of turbo-pump [4], propellant tank pressurization [5,6], chilldown of cryogenic transfer line [7] and squeeze film damper rotordynamics [8]. The purpose of the present paper is to investigate the applicability of the finite volume method to predict fluid transient in cryogenic flow circuits.

Majumdar, Alok↗

Advancing Building Air Leakage Measurement and Modeling: Measurement of Interior Air Leaks, Experimental Comparison to Conventional Methods, and Building Modeling Characteristics

This report, Advancing Building Air Leakage Measurement and Modeling: Measurement of Interior Air Leaks, Experimental Comparison to Conventional Methods, and Building Modeling Characteristics, developed two new building air leakage measurement methods, experimentally evaluated the performance in comparison to conventional methods, experimentally evaluated the behavior of leaks for specific crack structures, and identified testing constraints and model implications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Determination of the charge transport mechanism in p-n junctions by analyzing temperature dependences of forward current-voltage characteristics

A method is suggested for determining the charge transport mechanism in p-n junctions by analyzing the temperature dependence of forward current-voltage characteristics at a low injection level. The method has been experimentally tested with Si:Au diodes, green GaP LEDs, and blue AlGaN/InGaN/GaN LEDS with a quantum well.

36 MATERIALS SCIENCE↗

Method of investigation of vibroacoustic characteristics of centrifugal pumps

A method for acoustical diagnostics of pumps is described which consists of taking sonograms of the pump, by means of an audio spectrograph. In distinction from usual analyzers, the spectrograph makes it possible to obtain a three-dimensional image of the signal being analyzed, in which its frequency-amplitude characteristics developed over time are depicted with a resolving power of 0.004 sec. As an example, a sonogram of an electrically driven pump, in the 40-4000 Hz frequency range, is presented. The amplitude ratios are determined on the sonogram by the contrast of individual contours, with an accuracy of 6 db.

Pokrovskiy, B. V.↗

Analysis and testing of propellant feed system priming process

This paper presents the analytical and the experimental results pertaining to the priming process of the propellant feed system with initial line pressures starting from 0 psia and greater. The analytical methods employ the method of characteristics to solve for the one-dimensional liquid transients in the liquid-full segments and the lumped inertia technique to model the dynamics of the partially filled segments or the two-phase segments. The advantages of these methods are (1) fluid compressibility and piping flexibility are accounted for in the solution; and (2) the characteristics method can be used in the solution of a complex system. The analytical results were compared with test results. Excellent correlation was obtained between predictions and test results verifying the essential aspects of the analytical modeling techniques and providing the foundation for analyzing a complicated network system.

Lin, T. Y.↗