SEARCH · Search NASA

Results for “mixed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Mixing effectiveness test of an exhaust gas mixer in a high bypass turbofan at altitude

Thermal mixing effectiveness characteristics of an eighteen lobe, scalloped and unscalloped, partial, forced mixer were measured in a high-bypass turbofan engine. Data were also obtained without the mixer installed, i.e. free mixing. Tests were conducted at four combinations of simulated flight conditions from 0.3 to 0.8 Mach number and from 6,096 meters (20,000 ft) to 13,715 m (45,000 ft) altitude. Mixing chamber lengths of L/D = 0.52 and 0.65 were tested. For this range of test conditions and mixer configurations the forced mixing effectiveness varied from 59 to 68 percent. Values of mixing effectiveness and total pressure loss were calculated from temperature and pressure data obtained at the mixer inlet and exhaust nozzle exit.

Cullom, R. R.↗

NASA NTRS1982

Further considerations on modeling the sea breeze with a mixed-layer model

Mixed-layer models have been used to simulate low-level flows under a variety of situations, including flow over complex terrain and in the vicinity of coastal zones. The advantage of mixed-layer models compared to multilevel models is their simplicity and minimal computational requirements. A disadvantage is that the atmosphere above the mixed layer is not modeled explicitly and approximations pertaining to this layer become necessary. This paper examines five approximations for treating this upper layer for a simple sea-breeze circulation. Approximating the flow immediately above the mixed-layer height h by the mixed-layer velocity and using this velocity to advect potential temperature above h gives a better simulation of the sea breeze than the approximation used by Anthes et al. (1980), which neglected horizontal advection at this level.

Anthes, R. A.↗

NASA NTRS1982

Dilution Jet Mixing Program, phase 1

The effect of jet to mainstream density ratio, flow area convergence as encounted in transition sections, and nonuniform mainstream profile upstream of dilution orifices on the mixing of a row of jets with a confined cross flow was quantified. It is found that: (1) jet spreading rate in transverse direction is increased with increasing J, H/D and with decreasing S/D; (2) the density ratio has only a second order effect on the jet mixing characteristics for a constant momentum ratio; (3) the temperature distributions in the jet mixing region are strongly influenced by the undisturbed mainstream profile; (4) flow area convergence enhances mixing in radial and transverse directions. An asymmetric convergent duct with flat wall injection has the same jet mixing characteristics as a symmetric convergent duct. An asymmetric convergent duct with slant wall injection has a faster jet spreading rate in the transverse direction.

Srinivasan, R.↗

NASA NTRS1983

Combustion in a turbulent mixing layer formed at a rearward-facing step

A premixed propane/air flame was stabilized in a turbulent mixing layer formed at a rearward-facing step. The mean and rms averages of the turbulent velocity flowfield were determined by laser velocimetry for both reacting (phi = 0.57) and nonreacting flows (Re = 15,000-37,000 based on step height). The reacting-flow was visualized by high-speed schlieren photography. Large-scale structures dominate the reacting mixing layer. The growth of the large-scale structures was tied to the propagation of the flame. The linear growth rate of the reacting mixing layer defined by the mean velocity profiles was unchanged by combustion but the virtual origin moves downstream. The reacting mixing layer boundaries based on the mean velocity profiles were shifted toward the recirculation zone and reattachment lengths were shortened by 30 percent. The edge of the flame controlled by the large-scale structure development propagated faster into the incoming reactants than the boundary of the mixing layer given by the mean velocity flowfield. Thus, the region of high velocity gradient did not coincide with the region of high reaction and heat transfer.

Pitz, R. W.↗

NASA NTRS1982

Detection and evaluation of mixed pixels in Landsat agricultural scenes

A major problem area encountered in the identification and estimation of agricultural crop proportions in Landsat imagery involves the large proportion of the pixels which are mixed pixels, whose spectral response is influenced by more than one ground cover type. The development of methods for the detection and estimation of crop proportions in mixed pixels is presently reported. The procedure designated CASCADE, based on the estimation of the gradient image for the detection of mixed pixels, considers the consequences of a linear mixing model and is found to provide a method for the allocation of mixed pixels to the surrounding homogeneous region.

Merickel, M. B.↗

NASA NTRS1984

Comparison of full-scale engine and subscale model performance of a mixed flow exhaust system for an energy efficient engine (E3) propulsion system

A full scale engine test of the NASA/General Electric Company (GE) Energy Efficient Engine (E3) was conducted to demonstrate the E3 engine concept and evaluate its performance. The test program, performed at the GE outdoor engine test facilities in Peebles, OH, included a detailed evaluation of the total pressure and temperature profiles at the exit of the mixed flow exhaust system to determine its mixing effectiveness. Subscale model tests of the same mixed flow exhaust system had been previously conducted at FluiDyne Engineering Corporation in Minneapolis, Minnesota as part of the GE E3 mixer aerodynamic technology development program. The scale model and full scale engine nozzle exit survey data and the calculated mixing effectiveness are compared and discussed. Results indicate the full scale engine mixing effectiveness to be five percent higher than the scale model as a result of a geometric difference and higher turbulence levels in the engne exhaust flowfield.

Kuchar, A. P.↗

NASA NTRS1988

A streamwise vortex embedded in a plane mixing layer

Experimental results are presented on the interaction of a single streamwise vortex with a plane turbulent mixing layer. In the present setup, the vortex is generated by a half-delta wing mounted in the settling chamber of a blower-driven wind tunnel. Initially, the vortex is shown to ride just below the mixing layer, locally distorting the mean velocity and turbulence Reynolds stress distributions in the lower part of the mixing layer. Once the vortex becomes embedded within the mixing layer, the distortions are found to spread through the whole width of the layer, and the induced extra strain rates in the mixing layer result in the generation of additional, relatively large, Reynolds normal and shear stresses, mainly in the regions above the vortex.

Bell, James H.↗

NASA NTRS1989

Three-dimensional structure of a plane mixing layer

An experimental study is reported which shows the spanwise structure of a plane mixing layer originating from laminar boundary layers. Quantitative measurements are obtained for the first time which show the origin and evolution of streamwise vortices within the mixing layer. After the first spanwise vortex rollup occurs, streamwise structures are triggered in clusters within the braid region of the mixing layer. Further downstream, they realign to form pairs of counterrotating vortices. The maximum vorticity diffuses rapidly with increasing downstream distance while the vortices grow, scaling with the mixing layer vorticity thickness. The presence of the streamwise vortices leads to significant spanwise distortions in the mean and turbulence properties of the mixing layer. A consistent peak in the secondary shear stress exists for each streamwise vortex.

Bell, James H.↗

NASA NTRS1990

Shock enhancement and control of hypersonic mixing and combustion

Experimental and computational analyses of the possibility that shock-enhanced mixing can substantially increase the rate of mixing between coflowing streams of hydrogen and air are discussed. Numerical computations indicate that the steady interaction between a weak shock in air with a coflowing hydrogen jet can be approximated by the two-dimensional time-dependent interaction between a weak shock and an initially circular region filled with hydrogen imbedded in air. Experimental results obtained in a shock tube and contoured wall injector are presented. It is shown that the shock impinging process causes the light gas cylinder to split into two parts; one of these mixes rapidly with air and the other forms a stably stratified vortex pair which mixes more slowly. The geometry of the flow field and the mixing process and scaling parameters are assessed.

Marble, Frank E.↗

NASA NTRS1991

Mixing of multiple jets with a confined subsonic crossflow. Summary of NASA-supported experiments and modeling

Experimental and computational results on the mixing of single, double, and opposed rows of jets with an isothermal or variable temperature mainstream in a confined subsonic crossflow are summarized. The studies were performed to investigate flow and geometric variations typical of the complex 3-D flowfield in the dilution zone of combustion chambers in gas turbine engines. The principal observations from the experiments were that the momentum-flux ratio was the most significant flow variable, and that temperature distributions were similar (independent of orifice diameter) when the orifice spacing and the square-root of the momentum-flux ratio were inversely proportional. The experiments and empirical model for the mixing of a single row of jets from round holes were extended to include several variations typical of gas turbine combustors. Combinations of flow and geometry that gave optimum mixing were identified from the experimental results. Based on results of calculations made with a 3-D numerical model, the empirical model was further extended to model the effects of curvature and convergence. The principle conclusions from this study were that the orifice spacing and momentum-flux relationships were the same as observed previously in a straight duct, but the jet structure was significantly different for jets injected from the inner wall wall of a turn than for those injected from the outer wall. Also, curvature in the axial direction caused a drift of the jet trajectories toward the inner wall, but the mixing in a turning and converging channel did not seem to be inhibited by the convergence, independent of whether the convergence was radial or circumferential. The calculated jet penetration and mixing in an annulus were similar to those in a rectangular duct when the orifice spacing was specified at the radius dividing the annulus into equal areas.

Holdeman, James D.↗

NASA NTRS1991

Experimental study of cross-stream mixing in a cylindrical duct

An experimental investigation of cross stream injection and mixing was conducted with application to a low NO sub x combustor for the High Speed Civil Transport (HSCT). Mixing in a cylindrical chamber was studied for transverse injection from slanted slot and round orifice injectors. Momentum ratio, density ratio, and number were studied. Quantitative measurement of injectant concentration distributions were obtained by planar digital imaging of the Mie scattered light from an aerosol seed uniformly mixed with the injectant. The unmixedness, defined as the ratio of the r.m.s. concentration fluctuation to mean concentration in a plane perpendicular to the main flow direction, was found to be primarily a function of momentum ratio and injector spacing. An optimum spacing is indicated. Unmixedness is also a function of orifice size, or mass flow ratio, but the mass flow dependence can be accounted for by normalizing the unmixedness with its maximum theoretical value. The data indicate that a density ratio greater than unity retards mixing. It was found that above a certain momentum flux ratio, mixing with slanted slot injectors was better than with round hole injectors.

Vranos, A.↗

NASA NTRS1991

Effect of velocity ratio on plane mixing layer development - Influence of the splitter plate wake

The effect of the velocity ratio on the approach of a plane mixing layer to self-similarity was investigated experimentally. In the experiment, plane mixing layers with velocity ratios 0.5, 0.6, 0.7, 0.8, and 0.9 were generated in a mixing-layer wind tunnel consisting of two individually driven legs, in which the two streams were allowed to merge at the sharp edge of a tappered splitter plate. The leg driven by the bigger blower was operated at a free-stream velocity in the test section of 21 m/s, while the flow speed in the other leg was varied to change the velocity ratio. For each velocity ratio, the mean flow- and turbulence measurements were carried out at eight streamwise locations. Results showed that, for velocity ratios between 0.5 and 0.7, self-similarity of the mixing layer was achieved, with the asymptotic states comparable; mixing layers with higher velocity ratios failed to achieve a self-similar state within the measurement domain.

Mehta, R. D.↗

NASA NTRS1991

Experimental study of cross-stream mixing in a cylindrical duct

An experimental investigation of cross stream injection and mixing has been conducted with application to a low NO(x) combustor for the HSCT. Mixing in a cylindrical chamber has been studied for transverse injection from slanted slot and round orifice injectors. Momentum ratio, density ratio, and injector geometry were the primary variables. Slanted slots of various size, aspect ratio, and number were studied. Quantitative measurement of injectant concentration distributions were obtained by planar digital imaging of the Mie-scattered light from an aerosol seed uniformly mixed with the injectant. The unmixedness, defined as the ratio of the rms concentration fluctuation to mean concentration in a plane perpendicular to the main flow direction, was found to be primarily a function of momentum ratio and injector spacing. An optimum spacing is indicated. Unmixedness is also a function of orifice size, or mass flow ratio, but the mass flow dependence can be accounted for by normalizing the unmixedness with its maximum theoretical value. The data indicate that density ratio greater than unity retards mixing. It was found that above a certain momentum flux ratio, mixing with slanted slot injectors was better than with round hole injectors.

Vranos, A.↗

NASA NTRS1992

Experimental Study of Cross-Stream Mixing in a Rectangular Duct

An experimental investigation of non-reacting cross-stream jet injection and mixing in a rectangular duct was conducted for application in a low emissions combustor. Planar digital imaging was used to measure concentration distributions in planes perpendicular to the duct axis. Mixing rate was measured for 45 deg slanted slot and round orifice injectors. Five areas of inquiry are discussed: (1) mixing improves continuously with increasing momentum-flux ratio; (2) given a momentum-flux ratio, there is an optimum, orifice spacing; (3) mixing is more dependent on injector geometry than mass flow ratio; (4) mixing is influenced by relative slot orientation; and (5) jet structure is different for round holes and slanted slots injectors. The utility of acquiring multipoint fluctuating properties of the flow field is also demonstrated.

Liscinsky, D. S.↗

NASA NTRS1991

Segregation parameters and pair-exchange mixing models for turbulent nonpremixed flames

The progress of chemical reactions in nonpremixed turbulent flows depends on the coexistence of reactants, which are brought together by mixing. The degree of mixing can strongly influence the chemical reactions and it can be quantified by segregation parameters. In this paper, the relevance of segregation parameters to turbulent mixing and chemical reactions is explored. An analysis of the pair-exchange mixing models is performed and an explanation is given for the peculiar behavior of such models in homogeneous turbulence. The nature of segregation parameters in a H2/Ar-air nonpremixed jet flame is investigated. The results show that Monte Carlo simulation with the modified Curl's mixing model predicts segregation parameters in close agreement with the experimental values, providing an indirect validation for the theoretical model.

Chen, J.-Y.↗

NASA NTRS1991

A continuous mixing model for pdf simulations and its applications to combusting shear flows

The problem of time discontinuity (or jump condition) in the coalescence/dispersion (C/D) mixing model is addressed in this work. A C/D mixing model continuous in time is introduced. With the continuous mixing model, the process of chemical reaction can be fully coupled with mixing. In the case of homogeneous turbulence decay, the new model predicts a pdf very close to a Gaussian distribution, with finite higher moments also close to that of a Gaussian distribution. Results from the continuous mixing model are compared with both experimental data and numerical results from conventional C/D models.

Hsu, A. T.↗

NASA NTRS1992

Interrelationships between mixing ratios of long-lived stratospheric constituents

Relationships between the simultaneously measured mixing ratios of certain stratospheric constituents that are sometimes linear are argued to be expected for species of sufficiently long lifetime. Species whose local lifetimes are longer than quasi-horizontal-transport time scales are in climatological slope equilibrium, i.e., they share surfaces of constant mixing ratio, and a scatter plot of the mixing ratio of one versus that of the other collapses to a compact curve whose slope at any point is the ratio of the net global fluxes of the two species through the corresponding surface of constant mixing ratio. Species whose local lifetimes are greater than vertical transport time scales are in gradient equilibrium and their mixing ratios display a linear relationship. These statements are illustrated using results from a 2D chemistry-transport model.

Plumb, R. A.↗

NASA NTRS1992

Experimental study of cross-stream mixing in a rectangular duct

Liscinsky, D. S.↗