Search NASA⌕ Search

SEARCH · Search NASA

Results for “obliquity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Preliminary results for a large angle oblique jet impingement and flow and for the effect of initial conditions on the near field of an axisymmetric jet

The structure of an axisymmetric jet in the near field is discussed for jet noise and for jet impingment schemes for STOL aircraft. It is inferred from previous studies, and the inference is supported by analysis, that the scale and intensity of the turbulence structure at the jet exit plane are the important boundary conditions which effect the development of the flow in the near field. The techniques to study these effects while maintaining a uniform mean flow and the results which document the range of the initial conditions are presented. The large angle, oblique jet impingment condition is of interest in terms of the jet/flap interaction. Detailed turbulence data can be obtained with the specially constructed facility. The development of the flow and instrumentation system and initial data from the new facility are presented.

Foss, J. F.↗
NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗
NASA NTRS1972

An experimental investigation of an oblique-wing and body combination at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot wind tunnel to determine the aerodynamic characteristics of an oblique high aspect ratio wing in combination with a high fineness-ratio Sears-Haack body. Longitudinal and lateral-directional stability data were obtained at wing yaw angles from 0 deg to 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 6 deg and 9 deg. The effects of changes in Reynolds number, dihedral, and trailing-edge angle were studied along with the effects of a roughness strip on the upper and lower surfaces of the wing. Flow-visualization studies were made to determine the nature of the flow on the wing surfaces.

Graham, L. A.↗
NASA NTRS1973

Wind tunnel tests of an F-8 airplane model equipped with an oblique wing

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to study the lift, drag and stability characteristics of a 0.087-scale model of an operational airplane fitted with an oblique wing. The model wing was of elliptical planform with an unswept aspect ratio of 12.7 and a thickness of 10 percent. All other external geometric features of the model were scaled to the basic full size operational airplane with the engine inlet faired closed. Longitudinal and lateral-directional stability data were obtained with the wing at sweep angles of 0 deg, 45 deg and 60 deg Test Mach numbers ranged from 0.6 to 1.4 deg Angles of attack were between minus 4 deg and 8 deg at zero sideslip. Angles of sideslip were between plus and minus 4 degrees for two angles of attack depending upon the wing configuration. Tests were conducted at a Reynolds number of 6 million per foot except for a few runs when balance capacity limited the Reynolds number to 4 million per foot.

Graham, L. A.↗
NASA NTRS1973

Oblique structure of Jupiter's bow shock.

Description of the Pioneer 10 flyby trajectory to the nominal bow shock of Jupiter. The analogy between the earth's and Jupiter's bow shocks is extended to include some structural features associated with oblique plasma shocks. A question of special interest to be answered by Pioneer 10 is to what extent results regarding the earth's bow shock structure can be extrapolated, qualitatively and quantitatively, to Jupiter's interaction with the solar wind.

Greenstadt, E. W.↗
NASA NTRS1973

Flowfield analysis for successive oblique shock wave interactions with a turbulent boundary layer

A computation procedure is described for predicting flow fields which develop when successive interactions between oblique shock waves and a turbulent boundary layer occur. Computations were carried out for axisymmetric internal flows at free stream Mach numbers = 3.82 and 2.82. The effect of boundary layer bleed was considered for the free stream Mach number = 2.82 flow. A control volume analysis is used to predict changes in the flow field across the interactions. Two bleed flow models were considered. A turbulent boundary layer program was used to compute changes in the boundary layer between the interactions. The results given are for flows with two shock wave interactions and for bleed at the second interaction site. In principle the method described may be extended to account for additional interactions. The predicted results are compared with measured results and are shown to be in good agreement when the bleed flow rate is low (on the order of 3 percent of the boundary layer mass flow), or when there is no bleed. As the bleed flow rate is increased, differences between the predicted and measured results become larger. Shortcomings of the bleed flow models at higher bleed flow rates are discussed.

Sun, C. C.↗
NASA NTRS1974

Oblique Wing Remotely Piloted Research Aircraft. Volume 1: Development

The NASA Ames/DSI oblique wing remotely piloted research aircraft is a highly unusual, variable remotely piloted vehicle whose configuration and capabilities are the result of certain initial design guidelines that, in terms of conventional aircraft structures and configurations, would be considered to be contradictory and unachievable. Accordingly, the novel design of the yawed wing RPV is at odds in many respects with conventional aircraft practice. Novelty, then, forms the first, unwritten, design guideline. This design is intended to move away from convention in geometry, structure, and materials. The specific guidelines followed in the design of the yawed wing RPV and a short discussion of the impact of each on the configuration of the vehicle are presented.

Source record↗
NASA NTRS1974

Measurements in a large angle oblique jet impingement flow

Velocity and surface pressure measurements, in the flow field of an obliquely impinging jet, and their interpretation as regards the governing mechanics and the aerodynamic noise generation characteristics of such a flow are reported. A computer controlled probe positioning mechanism allowed the measurement of the velocity magnitude and direction in the plane parallel to the plate. The mean velocity and Reynolds stress components were recorded. Measures of the terms in the momentum equation reveal the character of the pressure gradients in the neighborhood of the stagnation point. The effects of the stagnation streamline location on the vorticity field and the vortex sound considerations are discussed in relationship to the aerodynamic noise generation effects of this flow.

Foss, J. F.↗
NASA NTRS1974

The passage of an infinite swept airfoil through an oblique gust

An approximate solution is reported for the unsteady aerodynamic response of an infinite swept wing encountering a vertical oblique gust in a compressible stream. The approximate expressions are of closed form and do not require excessive computer storage or computation time, and further, they are in good agreement with the results of exact theory. This analysis is used to predict the unsteady aerodynamic response of a helicopter rotor blade encountering the trailing vortex from a previous blade. Significant effects of three dimensionality and compressibility are evident in the results obtained. In addition, an approximate solution for the unsteady aerodynamic forces associated with the pitching or plunging motion of a two dimensional airfoil in a subsonic stream is presented. The mathematical form of this solution approaches the incompressible solution as the Mach number vanishes, the linear transonic solution as the Mach number approaches one, and the solution predicted by piston theory as the reduced frequency becomes large.

Adamczyk, J. L.↗
NASA NTRS1974

Flowfield analysis for successive oblique shock wave-turbulent boundary-layer interactions

Description of a procedure for predicting the flowfields that develop when successive interactions between oblique shock waves and a turbulent boundary layer occur. Such interactions may occur, for example, in engine inlets for supersonic aircraft. A control volume analysis is used to predict changes in the flow field across the interactions. Two bleed flow models are considered. The predicted results are compared with measured results and are shown to be in good agreement when the bleed flow rate is low, or when there is no bleed. Shortcomings of the bleed flow models at higher bleed flow rates are discussed.

Sun, C.-C.↗
NASA NTRS1974

Optimal aeroelastic design of an oblique wing structure

A procedure is presented for determining the optimal cover panel thickness of a wing structure to meet specified strength and static aeroelastic divergence requirements for minimum weight. Efficient reanalysis techniques using discrete structural and aerodynamic methods are used in conjunction with redesign algorithms driven by optimality criteria. The optimality conditions for the divergence constraint are established, and expressions are obtained for derivatives of the dynamic pressure at divergence with respect to design variables. The procedure is applied to an oblique wing aircraft where strength and stiffness are critical design considerations for sizing the cover thickness of the wing structure.

Gwin, L. B.↗