Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical gain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Micro-Mechanical Voltage Tunable Fabry-Perot Filters Formed in (111) Silicon

The MEMS (Micro-Electro-Mechanical-Systems) technology is quickly evolving as a viable means to combine micro-mechanical and micro-optical elements on the same chip. One MEMS technology that has recently gained attention by the research community is the micro-mechanical Fabry-Perot optical filter. A MEMS based Fabry-Perot consists of a vertically integrated structure composed of two mirrors separated by an air gap. Wavelength tuning is achieved by applying a bias between the two mirrors resulting in an attractive electrostatic force which pulls the mirrors closer. In this work, we present a new micro-mechanical Fabry-Perot structure which is simple to fabricate and is integratable with low cost silicon photodetectors and transistors. The structure consists of a movable gold coated oxide cantilever for the top mirror and a stationary Au/Ni plated silicon bottom mirror. The fabrication process is single mask level, self aligned, and requires only one grown or deposited layer. Undercutting of the oxide cantilever is carried out by a combination of RIE and anisotropic KOH etching of the (111) silicon substrate. Metallization of the mirrors is provided by thermal evaporation and electroplating. The optical and electrical characteristics of the fabricated devices were studied and show promissing results. A wavelength shift of 120nm with 53V applied bias was demonstrated by one device geometry using 6.27 micrometer air gap. The finesse of the structure was 2.4. Modulation bandwidths ranging from 91KHz to greater than 920KHz were also observed. Theoretical calculations show that if mirror reflectivity, smoothness, and parallelism are improved, a finesse of 30 is attainable. The predictions also suggest that a reduction of the air gap to 1 micrometer results in an increased wavelength tuning range of 175 nm with a CMOS compatible 4.75V.

Patterson, James D.↗
DOE OSTI2020

Topological nanophotonics for photoluminescence control

Rare-earth-doped nanocrystals are emerging light sources that can produce tunable emissions in colours and lifetimes, which has been typically achieved in chemistry and material science. However, one important optical challenge – polarization of photoluminescence – remains largely out of control by chemistry methods. Control over photoluminescence polarization can be gained via coupling of emitters to resonant nanostructures such as optical antennas and metasurfaces. However, the resulting polarization is typically sensitive to position disorder of emitters, which is difficult to mitigate. Recently, new classes of disorder-immune optical systems have been explored within the framework of topological photonics. Here we explore disorder-robust topological arrays of Mie-resonant nanoparticles for polarization control of photoluminescence of nanocrystals. We demonstrate polarized emission from rare-earth-doped nanocrystals governed by photonic topological edge states supported by zigzag arrays of dielectric resonators. We verify the topological origin of polarized photoluminescence by comparing emission from nanoparticles coupled to topologically trivial and nontrivial arrays of nanoresonators. We expect that our results may open a new direction in the study of topology-enable emission properties of topological edge states in many photonic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ten-valley excitonic complexes in charge-tunable monolayer WSe 2

Excitons dominate the optical response of two-dimensional (2D) semiconductors. Strong interactions produce peculiar excitonic complexes, which provide a testing ground for exciton and quantum many-body theories. Here, we report a hitherto unobserved many-body exciton that emerges upon filling both the K and Q valleys of WSe 2 . We optically probe the exciton landscape using charge-tunable devices with unusually thin dielectrics that facilitate doping up to several 10 13 cm −2 . We observe the emergence of the thermodynamically stable complex when 10 valleys are electrostatically filled. We gain insight into its physics using magneto-optical measurements. Our results are well-described by a model where the number of distinguishable Fermi seas interacting with the photoexcited electron-hole pair defines the complex’s behavior. In addition to expanding the repertoire of excitons in 2D semiconductors, this complex could probe the limit of exciton models and answer open questions about screened Coulomb interactions in 2D semiconductors.

M exciton↗
DOE OSTI2023

Sharp, high numerical aperture (NA), nanoimprinted bare pyramid probe for optical mapping

The ability to correlate optical hyperspectral mapping and high resolution topographic imaging is critically important to gain deep insight into the structure–function relationship of nanomaterial systems. Scanning near-field optical microscopy can achieve this goal, but at the cost of significant effort in probe fabrication and experimental expertise. To overcome these two limitations, we have developed a low-cost and high-throughput nanoimprinting technique to integrate a sharp pyramid structure on the end facet of a single-mode fiber that can be scanned with a simple tuning-fork technique. The nanoimprinted pyramid has two main features: (1) a large taper angle (~70°), which determines the far-field confinement at the tip, resulting in a spatial resolution of 275 nm, an effective numerical aperture of 1.06, and (2) a sharp apex with a radius of curvature of ~20 nm, which enables high resolution topographic imaging. Optical performance is demonstrated through evanescent field distribution mapping of a plasmonic nanogroove sample, followed by hyperspectral photoluminescence mapping of nanocrystals using a fiber-in-fiber-out light coupling mode. Through comparative photoluminescence mapping on 2D monolayers, we also show a threefold improvement in spatial resolution over chemically etched fibers. These results show that the bare nanoimprinted near-field probes provide simple access to spectromicroscopy correlated with high resolution topographic mapping and have the potential to advance reproducible fiber-tip-based scanning near-field microscopy.

47 OTHER INSTRUMENTATION↗
NASA NTRS1997

Evolutionary Design of Controlled Structures

Basic physical concepts of structural delay and transmissibility are provided for simple rod and beam structures. Investigations show the sensitivity of these concepts to differing controlled-structures variables, and to rational system modeling effects. An evolutionary controls/structures design method is developed. The basis of the method is an accurate model formulation for dynamic compensator optimization and Genetic Algorithm based updating of sensor/actuator placement and structural attributes. One and three dimensional examples from the literature are used to validate the method. Frequency domain interpretation of these controlled structure systems provide physical insight as to how the objective is optimized and consequently what is important in the objective. Several disturbance rejection type controls-structures systems are optimized for a stellar interferometer spacecraft application. The interferometric designs include closed loop tracking optics. Designs are generated for differing structural aspect ratios, differing disturbance attributes, and differing sensor selections. Physical limitations in achieving performance are given in terms of average system transfer function gains and system phase loss. A spacecraft-like optical interferometry system is investigated experimentally over several different optimized controlled structures configurations. Configurations represent common and not-so-common approaches to mitigating pathlength errors induced by disturbances of two different spectra. Results show that an optimized controlled structure for low frequency broadband disturbances achieves modest performance gains over a mass equivalent regular structure, while an optimized structure for high frequency narrow band disturbances is four times better in terms of root-mean-square pathlength. These results are predictable given the nature of the physical system and the optimization design variables. Fundamental limits on controlled performance are discussed based on the measured and fit average system transfer function gains and system phase loss.

Masters, Brett P.↗
NASA NTRS2001

Power enhanced frequency conversion system

A frequency conversion system includes at least one source providing a first near-IR wavelength output including a gain medium for providing high power amplification, such as double clad fiber amplifier, a double clad fiber laser or a semiconductor tapered amplifier to enhance the power output level of the near-IR wavelength output. The NFM device may be a difference frequency mixing (DFM) device or an optical parametric oscillation (OPO) device. Pump powers are gain enhanced by the addition of a rare earth amplifier or oscillator, or a Ra-man/Brillouin amplifier or oscillator between the high power source and the NFM device.

Sanders, Steven↗
DOE OSTI2023

Large two-photon cross sections and low-threshold multiphoton lasing of CdS/CdSe/CdS quantum shells

Colloidal quantum shells are spherical semiconductor quantum wells, which have shown strong promise as optical materials, particularly in classes of experiments requiring multiple excitons. The two-photon properties of CdS/CdSe/CdS quantum shell samples are studied here to demonstrate large non-linear absorption cross-sections while retaining advantageous multiexciton physics conferred by the geometrical structure. The quantum shells have large two-phonon cross sections (0.4–7.9 × 10 6 GM), which highlights their potential use in upconversion imaging in which large per particle two-photon absorption is critical. Time-resolved measurements confirmed that the quantum shells have long biexciton lifetime (>10 ns in the largest core samples reported here) and large gain bandwidth (>300 meV). The combination of these attributes with large two-photon cross sections makes the CdS/CdSe/CdS quantum shells excellent gain media for two-photon excitation. With a broad gain bandwidth and long gain lifetime, quantum shell solids support multimodal amplified spontaneous emission from excitons, biexcitons, and higher excited states. In conclusion, thresholds for amplified spontaneous emission and lasing, which are as low as 1 mJ cm −2 , are comparable to, or lower than, the thresholds reported for other colloidal materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1999

Polycapillary X-Ray Optics for X-Ray Astronomy

High-energy x-ray spectrometry from astronomical sources is difficult due to low flux rates and high background. Polycapillary x-ray optics can be used to increase the signal-to-noise ratio by focusing photons onto a small energy dispersive detector. Two optics, both designed for x-ray astronomy, have been built and tested as collimating optics with a microfocus x-ray source for x-ray energies up to 70 keV and as focusing optics with parallel x-rays up to 50 keV. Results from these tests show that polycapillary x-ray optics have transmission efficiencies ranging from 5% to 40% and signal gains ranging from 5 to over 100 for energies up to 50 keV. Furthermore the results show that these optics have potential for use up to 100 keV. The experimental results as well as simulations for the measured and for optimized optics will be discussed.

Russell, C. H.↗
NASA NTRS1997

Brillouin Opto-Electronic Oscillator

We demonstrate an all optical Opto-Electronic Oscillator in which the Brillouin selective sideband amplification technique is used to provide a sufficient gain for the oscillator to start and sustain an electro-optic oscillation.

OEO electro-optic oscillation↗
DOE OSTI2020

Engineering Directionality in Quantum Dot Shell Lasing Using Plasmonic Lattices

In this paper, we report how the direction of quantum dot (QD) lasing can be engineered by exploiting high-symmetry points in plasmonic nanoparticle (NP) lattices. The nanolaser architecture consists of CdSe-CdS core-shell QD layers conformally coated on two-dimensional square arrays of Ag NPs. Using waveguide-surface lattice resonances (W-SLRs) near the Δ point in the Brillouin zone as optical feedback, we achieved lasing from the gain in CdS shells at off-normal emission angles. Changing the periodicity of the plasmonic lattices enables other high-symmetry points (Γ or M) of the lattice to overlap with the QD shell emission, which facilitates tuning of the lasing direction. We also increased the thickness of the QD layer to introduce higher order W-SLR modes with additional avoided crossings in the band structure, which expands the selection of cavity modes for any desired lasing emission angle.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Optimal gas cooling with minimal aero-opticaldistortion for next generation high-average-power lasers (Progress report, Year 2)

Next-generation lasers that combine high-peak-power ultrashort pulses with high repetition rates have the potential to efficiently deliver the high-average-power outputs required for inertial fusion energy generation, laser-based particle acceleration, and to generate compact secondary x- and 𝛾-ray radiation sources, among others. The combination of long gain length with high surface-to-volume ratio to remove residual heat makes gas-cooled multi-slab amplifier heads an inherently aperture- and average power scalable technology that enables this new class of solid-state lasers, and their thermal management becomes the most pressing technical challenge. As the index-of refraction depends on the gas density, heat removal from the slab surfaces unavoidably entails scattering of propagated light from regions of high temperature fluctuations. The requirement to maximize convective heat extraction from the gain medium under the constraint of minimum optical aberration of the beam renders amplifier slab cooling a technological challenge at the intersection of aero-optics, fluid-mechanics and heat transfer. The goal of this research is to leverage computational fluid dynamics and aero optics simulations of different levels of fidelity to devise a numerical modeling and optimization framework for gas-cooled multi-slab amplifiers. The project will be conducted in close collaboration with the Advanced Photon Technologies Group at Lawrence Livermore National Laboratory, where a gas-cooled test stand for laser materials and thermal management structures will be developed and installed. The final goal of the collaborative effort is to manufacture and benchmark a physical prototype of an numerically optimized amplifier head design. Measurement data on solid-state and thermo-optical distortions will be used for the validation of the numerical models. The key technical challenge in this multi-objective design problem is that of balancing optimal heat removal with minimal optical distortion. To facilitate computationally efficient design optimization and, at the same time, deepen our basic understanding of the interaction of light with turbulence, a complementary study that combines high and low-fidelity flow simulations and aero-optical models is proposed. Along the lines of these two objectives and solution strategies, the project is organized into two thrusts.

42 ENGINEERING↗
NASA NTRS1975

Laser action generated within a light pipe: A concept

Laser light could be generated within light pipe itself, thereby eliminating coupling losses. Theoretical calculations have shown feasibility of light-pipe laser propagating in circularly-polarized TE mode. It is predicted that fiber-optic distributed-feedback laser would have gain on order of 25 dB.

Elachi, C.↗
NASA NTRS1974

Measurement of the lidar cross sections of cube corner arrays for laser ranging of satellites

The satellite coordinate system necessary to describe the location and orientation of each cube corner in the array is discussed. The method of optical testing is described along with the gain function, and computational methods for deriving the gain function and experimental values for it. The velocity aberration is derived as a function of satellite orbit, a complete method for cross section evaluation is described, and finally the radar equation is described.

Minott, P. O.↗
NASA NTRS1980

Optical observables in stars with non-stationary atmospheres

Experience gained by use of Cepheid modeling codes to predict the dimensional and photometric behavior of nuclear fireballs is used as a means of validating various computational techniques used in the Cepheid codes. Predicted results from Cepheid models are compared with observations of the continuum and lines in an effort to demonstrate that the atmospheric phenomena in Cepheids are quite complex but that they can be quantitatively modeled.

Hillendahl, R. W.↗
NASA NTRS1989

Evaluation of the feasibility of a far-infrared laser based on intersubband transitions in GaAs quantum wells

The threshold current and quantum efficiency are calculated for an FIR injection laser based on intersubband transitions in GaAs single quantum wells. By considering the balance of gain against the free carrier and transverse optical phonon absorption, and the intersubband transition time, the wavelength dependence of the threshold current is calculated. For the wavelength range 50-120 microns, the required threshold currents are the lowest and have reasonable values of 1-10 kA/sq cm. The threshold quantum efficiency in that range is expected to be about 0.0001.

Borenstain, Shmuel I.↗
NASA NTRS1991

Self-Injection Locking Of Diode Lasers

Simple optical coupling scheme locks array of gain-guided diode lasers into oscillation in single mode and with single-lobed output beam. Selective feedback from thin etalon self-injection-locks array into desired mode. One application of new scheme for pumping of neodymium: yttrium aluminum garnet lasers with diode-laser arrays.

Hemmati, H.↗
NASA NTRS1993

OTV bearing deflection investigation

The primary goal of the Bearing Deflectometer Investigation was to gain experience in the use of fiber optic displacement probe technology for bearing health monitoring in a liquid hydrogen turbo pump. The work specified in this Task Order was conducted in conjunction with Air Force Rocket Propulsion Laboratory Contract F04611-86-C-0010. APD conducted the analysis and design coordination to provide a displacement probe design compatible with the XLR-134 liquid hydrogen turbo pump assembly (TPA). Specifications and requirements of the bearing deflectometer were established working with Mechanical Technology Instruments, Inc. (MTI). The TPA design accommodated positioning of the probe to measure outer race cyclic deflections of the pump inlet bearing. The fiber optic sensor was installed as required in the TPA and sensor output was recorded during the TPA testing. Data review indicated that no bearing deflection signature could be differentiated from the inherent system noise. Alternate sensor installations were not investigated, but might yield different results.

Reimer, B. L.↗
NASA NTRS2000

946 nm Diode Pumped Laser Produces 100mJ

An innovative approach to obtaining high energy at 946 nm has yielded 101 mJ of laser energy with an optical-to-optical slope efficiency of 24.5%. A single gain module resonator was evaluated, yielding a maximum output energy of 50 mJ. In order to obtain higher energy a second gain module was incorporated into the resonator. This innovative approach produced un-surprised output energy of 101 mJ. This is of utmost importance since it demonstrates that the laser output energy scales directly with the number of gain modules. Therefore, higher energies can be realized by simply increasing the number of gain modules within the laser oscillator. The laser resonator incorporates two gain modules into a folded "M-shaped" resonator, allowing a quadruple pass gain within each rod. Each of these modules consists of a diode (stack of 30 microlensed 100 Watt diode array bars, each with its own fiber lens) end-pumping a Nd:YAG laser rod. The diode output is collected by a lens duct, which focuses the energy into a 2 mm diameter flat to flat octagonal pump area of the laser crystal. Special coatings have been developed to mitigate energy storage problems, including parasitic lasing and amplified spontaneous emission (ASE), and encourage the resonator to operate at the lower gain transition at 946 nm.

Axenson, Theresa J.↗