Search NASA⌕ Search

SEARCH · Search NASA

Results for “orifice”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Excitation of a Helmholtz resonator by a turbulent boundary layer

A turbulent boundary layer on the fuselage of a glider was used to excite a Helmholtz resonator. The resonator orifice was flush with the surface and smaller than the boundary layer thickness. Resonator frequencies were chosen so they would tune with different portions of the boundary layer wall pressure spectrum. The resonators were excited at both the Helmholtz frequency and a standing wave frequency. The results show a shift in the Helmholtz frequency when the boundary layer is present. This shift indicates the degree to which the turbulence interacts with the acoustic motion in the orifice and modifies the end correction. Four of the nine resonators tested were 'strongly' excited and radiated considerable acoustic sound. This phenomenon occurs when turbulent eddies about the size of the orifice are convected past the orifice with the proper velocity to impose a frequency that matches a resonant frequency of the resonator. Turbulent eddies which are either smaller or larger than the orifice will not produce strong excitation.

Panton, R. L.↗
NASA NTRS1976

Flow visualization in long neck Helmholtz resonators with grazing flow

Both oscillating and steady flows were applied to a single plexiglass resonator cavity with colored dyes injected in both the orifice and grazing flow field to record the motion of the fluid. For oscillatory flow, the instantaneous dye streamlines were similar for both the short and long-neck orifices. The orifice flow blockage appears to be independent of orifice length for a fixed amplitude of flow oscillation and magnitude of the grazing flow. The steady flow dye studies showed that the acoustic and steady flow resistances do not necessarily correspond for long neck orifices.

Baumeister, K. J.↗
NASA NTRS1976

Flow visualization in long neck Helmholtz resonators with grazing flow

Both oscillating and steady flows were applied to a single plexiglass resonator cavity with colored dyes injected in both the orifice and grazing flow field to record the motion of the fluid. For oscillatory flow, the instantaneous dye streamlines were similar for both the short and long-neck orifices. The orifice flow blockage appears to be independent of orifice length for a fixed amplitude of flow oscillation and magnitude of the grazing flow. The steady flow dye studies showed that the acoustic and steady flow resistances do not necessarily correspond for long neck orifices.

Baumeister, K. J.↗
NASA NTRS1978

An investigation of mercury hollow cathode phenomena

An experimental investigation is described in which measurements were made of plasma properties and other physical parameters upstream and downstream of the orifice plate of an operating mercury hollow cathode. These measurements included plasma property profiles, internal surface temperatures, internal pressure, and spectroscopic data of the external discharge. The results show the plume-to-spot mode transition to be characterized by significant changes in the plasma properties downstream of the cathode orifice, including the disappearance of an apparent electron free-fall region which is found to be present in the plume mode. The results also indicate the existence of a very dense plasma (10 to the 10th to 10 to the 14th electrons/cu cm) with steep electron density gradients in the region upstream of the orifice. The upstream data is found to correlate well with a modified form of the Saha equation. The related analysis indicates that the heavy particles approach thermal equilibrium with the electrons in the region of the orifice and that the ionization fraction in the orifice is very high - 80 to 100%.

Siegfried, D. E.↗
NASA NTRS1987

Qualitative evaluation of a flush air data system at transonic speeds and high angles of attack

Flight tests were performed on an F-14 aircraft to evaluate the use of flush pressure orifices on the nose section for obtaining air data at transonic speeds over a large range of flow angles. This program was part of a flight test and wind tunnel program to assess the accuracies of such systems for general use on aircraft. It also provided data to validate algorithms developed for the shuttle entry air data system designed at NASA Langley. Data were obtained for Mach numbers between 0.60 and 1.60, for angles of attack up to 26.0 deg, and for sideslip angles up to 11.0 deg. With careful calibration, a flush air data system with all flush orifices can provide accurate air data information over a large range of flow angles. Several orificies on the nose cap were found to be suitable for determination of stagnation pressure. Other orifices on the nose section aft of the nose cap were shown to be suitable for determination of static pressure. Pairs of orifices on the nose cap provided the most sensitive measurements for determining angles of attack and sideslip, although orifices located farther aft on the nose section could also be used.

Larson, Terry J.↗
NASA NTRS1990

Flow-induced resonance of screen-covered cavities

An experimental study of screen-covered cavities exposed to airflow tangent to the screen is described. The term screen refers to a thin metal plate perforated with a repetitive pattern of round holes. The purpose was to find the detailed aerodynamic and acoustic mechanisms responsible for screen-covered cavity resonance and to find ways to control the pressure oscillations. Results indicate that strong cavity acoustic resonances are created by screen orifices that shed vortices which couple resonance by choosing hole spacings such that shed vortices do not arrive at a downstream orifice in synchronization with cavity pressure oscillations. The proper hole pattern is effective at all airspeeds. It was also discovered that a reduction of orifice size tended to weaken the screen/cavity interaction regardless of hole pattern, probably because of viscous flow losses at the orifices. The screened cavities that resonated did so at much higher frequencies than the equivalent open cavity. The classical large eddy phenomenon occurs at the relatively small scale of the orifices (the excitation is typically of high frequency). The wind tunnel study was made at airspeeds from 0 to 100m/sec. The 457-mm-long by 1.09-m-high rectangular cavities had length-to-depth ratios greater than one, which is indicative of shallow cavities. The cavity screens were perforated in straight rows and columns with hole diameters ranging from 1.59 to 6.35 mm and with porosities from 2.6 to 19.6 percent.

Soderman, Paul T.↗
NASA NTRS1995

Angled injection: Hybrid fluid film bearings for cryogenic applications

A computational bulk-flow analysis for prediction of the force coefficients of hybrid fluid film bearings with angled orifice injection is presented. Past measurements on water-lubricated hybrid bearings with angle orifice injection have demonstrated improved rotordynamic performance with virtual elimination of cross-coupled stiffness coefficients and nul or negative whirl frequency ratios. A simple analysis reveals that the fluid momentum exchange at the orifice discharge produces a pressure rise in the recess which retards the shear flow induced by journal rotation, and consequently, reduces cross-coupling forces. The predictions from the model correlate well with experimental measurements from a radial and 45 deg angled orifice injection, five recess water hybrid bearings (C = 125 microns) operating at 10.2, 17.4, and 24.6 krpm and with nominal supply pressures equal to 4, 5.5, and 7 MPa. An application example for a liquid oxygen six recess/pad hybrid journal bearing shows the advantages of tangential orifice injection on the rotordynamic force coefficients and stability indicator for forward whirl motions and without performance degradation on direct stiffness and damping coefficients. The computer program generated, 'hydrojet,' extends and complements previously developed codes.

SanAndres, Luis↗
NASA NTRS1996

Production of Gas Bubbles in Reduced Gravity Environments

In a wide variety of applications such as waste water treatment, biological reactors, gas-liquid reactors, blood oxygenation, purification of liquids, etc., it is necessary to produce small bubbles in liquids. Since gravity plays an essential role in currently available techniques, the adaptation of these applications to space requires the development of new tools. Under normal gravity, bubbles are typically generated by forcing gas through an orifice in a liquid. When a growing bubble becomes large enough, the buoyancy dominates the surface tension force causing it to detach from the orifice. In space, the process is quite different and the bubble may remain attached to the orifice indefinitely. The most practical approach to simulating gravity seems to be imposing an ambient flow to force bubbles out of the orifice. In this paper, we are interested in the effect of an imposed flow in 0 and 1 g. Specifically, we investigate the process of bubble formation subject to a parallel and a cross flow. In the case of parallel flow, we have a hypodermic needle in a tube from which bubbles can be produced. On the other hand, the cross flow condition is established by forcing bubbles through an orifice on a wall in a shear flow. The first series of experiments have been performed under normal gravity conditions and the working fluid was water. A high quality microgravity facility has been used for the second type and silicone oil is used as the host liquid.

Oguz, Hasan N.↗
NASA NTRS1996

Quick-Mixing Studies Under Reacting Conditions

The low-NO(x) emitting potential of rich-burn/quick-mix/lean-burn )RQL) combustion makes it an attractive option for engines of future stratospheric aircraft. Because NO(x) formation is exponentially dependent on temperature, the success of the RQL combustor depends on minimizing high temperature stoichiometric pocket formation in the quick-mixing section. An experiment was designed and built, and tests were performed to characterize reaction and mixing properties of jets issuing from round orifices into a hot, fuel-rich crossflow confined in a cylindrical duct. The reactor operates on propane and presents a uniform, non-swirling mixture to the mixing modules. Modules consisting of round orifice configurations of 8, 9, 10, 12, 14, and 18 holes were evaluated at a momentum-flux ratio of 57 and jet-to-mainstream mass-flaw ratio of 2.5. Temperatures and concentrations of O2, CO2, CO, HC, and NO(x) were obtained upstream, down-stream, and within the orifice plane to determine jet penetration as well as reaction processes. Jet penetration was a function of the number of orifices and affected the mixing in the reacting system. Of the six configurations tested, the 14-hole module produced jet penetration close to the module half-radius and yielded the best mixing and most complete combustion at a plane one duct diameter from the orifice leading edge. The results reveal that substantial reaction and heat release occur in the jet mixing zone when the entering effluent is hot and rich, and that the experiment as designed will serve to explore satisfactorily jet mixing behavior under realistic reacting conditions in future studies.

Leong, May Y.↗
NASA NTRS2002

Synthetic Jet Interaction With A Turbulent Boundary Layer Flow

Perhaps one of the more notable advances to have occurred in flow control technology in the last fifteen years is the application of surface-issuing jets for separation control on aerodynamic surfaces. The concept was introduced by Johnston and Night (1990) who proposed using circular jets, skewed and inclined to the wall, to generate streamwise vortices for the purpose of mitigating boundary layer separation. The skew and inclination angles have subsequently been shown to affect the strength and sign of the ensuing vortices. With a non-circular orifice, in addition to skew and inclination, the yaw angle of the major axis of the orifice can influence the flow control effectiveness of the jet. In particular, a study by Chang arid Collins (1997) revealed that a non-circular orifice, yawed relative to the freestream, can be used to control the size and strength of the vortices produced by the control jet. This early work used jets with only a steady injection of mass. Seifert et al. revealed that an unsteady blowing jet, could be as effective at separation control as a steady jet but with less mass flow. Seifert et al. showed that small amplitude blowing oscillations superimposed on a low momentum steady jet Was the most effective approach to delaying separation on a NACA 0015 airfoil at post-stall angles of attack. More recent work suggests that perhaps the most efficient jet control effect comes from a synthetic (oscillatory) jet where the time-averaged mass flux through the orifice is zero, but the net wall normal momentum is non-zero. The control effectiveness of synthetic jets has been demonstrated for several internal and external flow fields used synthetic jet control on a thick, blunt-nosed airfoil to delay stall well beyond the stall angles for the uncontrolled airfoil and with a dramatic increase in the lift-to-drag performance. Amitay et al. used an array of synthetic jets to mitigate flow separation in curved and diffusing ducts. While the control effectiveness of synthetic jet actuators in an application setting has been confirmed through a number of studies, the fluid dynamic mechanism by which control is effected is not well understood. Issues like yaw angle arid velocity ratio that have been studied for steady control jets have not been investigated for synthetic jets. Moreover, the role played by the inherently unsteady nature of a synthetic jet in the interaction with the controlled flow is not known. Some recent work by Rinehart and Glazer and Smith suggests that away from tile immediate vicinity of the jet orifice the flow field is steady in the mean, and that the interaction of a synthetic jet and a boundary layer creates a secondary flow in the boundary layer consisting primarily of streamwise vortices.

Smith, Douglas R.↗
NASA NTRS2003

Enhanced Mixing in a Rectangular Duct

An experimental investigation of the mixing of non-reacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. Particular emphasis was placed on the study of closely spaced orifice configurations applicable to the mixing zone of an RQL combustor. Baseline studies were performed of mixing under "ideal" conditions, i.e., plenum fed jets injecting into a crossflow uniform in velocity and turbulence intensity. In addition, more practical ("non-ideal") issues encountered during hardware design were also studied. As in other studies, mixing effectiveness, determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions, was found to be optimum when the spacing-to-duct-height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. This relationship is suitable for design under ideal flow conditions. Inlet flow boundary conditions of the jet and approach flow (mainstream) were found to strongly influence mixing performance, but no attempt was made to determine optimum performance under non-ideal conditions. The tests performed do offer some guidance as to expected mixing behavior for several common variables likely to be imposed by hardware constraints. Additionally, in this study it was found that for rows of orifices with opposite centerlines inline, mixing was similar for blockages up to 89 percent (previous crossflow mixing studies concerned with dilution zone configurations, blockages were typically less than 50 percent). Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but blockage must be =50 percent in this configuration. Round hole and "square" orifice shapes had similar performance. Other variations in orifice shape did not substantially augment overall mixing performance. Furthermore an isothermal mixing data set was generated and used by CFDRC as input to a NO(x) inference code.

Liscinsky, D. S.↗
NASA NTRS2003

Fast-Acting Valve

A fast-acting valve includes an annular valve seat that defines an annular valve orifice between the edges of the annular valve seat, an annular valve plug sized to cover the valve orifice when the valve is closed, and a valve-plug holder for moving the annular valve plug on and off the annular valve seat. The use of an annular orifice reduces the characteristic distance between the edges of the valve seat. Rather than this distance being equal to the diameter of the orifice, as it is for a conventional circular orifice, the characteristic distance equals the distance between the inner and outer radii (for a circular annulus). The reduced characteristic distance greatly reduces the gap required between the annular valve plug and the annular valve seat for the valve to be fully open, thereby greatly reducing the required stroke and corresponding speed and acceleration of the annular valve plug. The use of a valve-plug holder that is under independent control to move the annular valve plug between its open and closed positions is important for achieving controllable fast operation of the valve.

Wojciechowski, Bogdan V.↗
NASA NTRS2007

Experimental Evaluation of an Isolated Synthetic Jet IN Crossflow

The second case for this workshop builds upon the isolated synthetic jet of Case 1 by adding a crossflow, with no streamwise pressure gradient, for the developing jet to interact with. Formally, Case 2 examines the interaction of a single, isolated, synthetic jet and a fully turbulent zero-pressure gradient boundary layer. The resulting flow has many of the characteristics that need to be modeled with fidelity if the results of the calculations are to serve as the basis for research and design with active flow control devices. These include the turbulence in the boundary layer, the time-evolution of the large vortical structure emanating from the jet orifice and its subsequent interaction with and distortion by the boundary layer turbulence, and the effect of the suction cycle on the boundary layer flow. In a synthetic jet, the flow through the orifice and out into the outer flowfield alternates between an exhaust and a suction cycle, driven by the contraction and expansion of a cavity internal to the actuator. In the present experiment, the volume changes in the internal cavity are accomplished by replacing one of the rigid walls of the cavity, the wall opposite the orifice exit, with a deformable wall. This flexible wall is driven by a bottom-mounted moveable piston. The piston is driven electro-mechanically. The synthetic jet issues into the external flow through a circular orifice. In the present experiment, this orifice has a diameter of 0.250 inches (6.35 mm). The flow is conceptually similar to that documented in Schaeffler [1]. To document the flow, several measurement techniques were utilized. The upstream boundary conditions (in-flow conditions), and several key phase-averaged velocity profiles were measured with a 3-component laser-Doppler velocimetry system. Phase-averaged velocity field measurements were made with both stereo digital particle image velocimetry and 2-D digital particle image velocimetry as the primary measurement system. Surface pressure measurements were made utilizing an electronically scanned pressure system.

Schaeffler, Norman W.↗
NASA NTRS2008

Atomizer for thermal management system

An atomizer for thermal management system for efficiently thermally managing one or more heat producing devices. The atomizer for thermal management system includes a housing having a coolant passage and a dispensing end, an orifice within the dispensing end, and an actuator manipulating a plunger within the housing. The plunger includes a head that is sealable within a recessed portion of the orifice to open or close the orifice. The coolant passes through the coolant passage into the orifice for spraying upon a heat producing device. The actuator may reciprocate so that the coolant spray emitted through the orifice is pulsating. The pulsing frequency may be increased to increase cooling or decreased to decrease cooling of the heat producing device.

Tilton, Charles L.↗
NASA NTRS1972

Neutral-particle wake method for measuring the atmospheric temperature from a satellite.

Description of a method that would permit a satellite-borne neutral mass spectrometer to measure the atmospheric temperature. The spectrometer examines the partial pressure variations that occur as the wake of a small rectangular baffle is swept across the entrance orifice of the spectrometer. For a given baffle size and for a mounting distance from the orifice, the depth of the resulting pressure minimum depends only on the thermal velocity or temperature of the observed species. The validity of the method can be checked by measuring the wake characteristics of more than one species and/or by employing each of several baffle sizes. The theory includes the effect of a finite orifice size, finite baffle length, and the backscattering of particles from the baffle into the orifice. It is found that a suitable baffle arrangement can be achieved that will permit the temperature to be measured over at least the range normally encountered in the thermosphere (200 to 2000 K) and, depending on the sensitivity and background pressure of the spectrometer, over an altitude range of about 140 to 600 km.

Brace, L. H.↗
NASA NTRS1973

Multiple jet study

Test data is presented which allows determination of jet penetration and mixing of multiple cold air jets into a ducted subsonic heated mainstream flow. Jet-to-mainstream momentum flux ratios ranged from 6 to 60. Temperature profile data is presented at various duct locations up to 24 orifice diameters downstream of the plane of jet injection. Except for two configurations, all geometries investigated had a single row of constant diameter orifices located transverse to the main flow direction. Orifice size and spacing between orifices were varied. Both of these were found to have a significant effect on jet penetration and mixing. The best mixing of the hot and cold streams was achieved with duct height.

Walker, R. E.↗
NASA NTRS1972

Nonlinearity of Helmholtz resonators

Consideration of the nonlinear damping of pressure oscillations by means of acoustic liners consisting of a perforated plate communicating with a volume or of individual Helmholtz resonators. A nonlinear analysis leads to a modified first-order theory; in particular, some second-order damping effects (due to the formation of jets through the orifices) are considered, while other less important damping effects (of second order) are neglected. The effect of the vena contracta in the orifice flow is also taken into account, and the conditions of maximum damping are discussed. A determination is made of the orifice velocity, the cavity pressure, the admittance coefficient, the resistance, and the reactance, and good agreement is found between the theoretically determined resistance and orifice velocity and the pertinent experimental data.

Sirignano, W. A.↗
NASA NTRS1974

Design, fabrication, and testing of a cryogenic thermal diode

Cryogenic heat pipe diode applications and a new heat pipe geometry are discussed. This new geometry employs excess liquid to block the vapor space of the evaporator and part of the transport section during reverse mode conditions. An orifice plate is positioned in the pipe at the blocking meniscus location, with the opening arranged to permit proper liquid distribution in both ground tests and zero g operation. Experimental data are presented for a room temperature heat pipe modified to operate as a blocking orifice diode. The test results verify feasibility of the blocking orifice technique with the diode having a rapid shutoff characteristic. The selection of a diode for fabrication and test was based mainly on a parametric investigation of the liquid trap and liquid blockage techniques. The blocking orifice form of liquid blockage was selected for the cryogenic diode based on its high throughput, small reservoir requirement, and small energy and time required for shutoff.

Quadrini, J.↗